K-BUS IR Emitter & IR Learner User manual-Ver. 1
Contents
1. 5 4 Instructions for the PC software 6 4 1 Start windOoW 6 4 2 Function configuration WINdOW 8 4 2 1 Channel 8 4 2 2 Group address area 9 4 2 3 Function address assignment area 10 4 2 4 Function area 10 4 3 Learning IR function 11 4 4 New a configuration file 14 GYS K BUS KNX EIB IR Emitter and IR Learner 1 General We call it IR Learning that combine the three parts PC Software IR Learner and IR Emitt2. Before the PC software has not been configured the KNX communication interface yet the button Program Address amp Application and Program application are shown gray and can not use and the status bar displays Enx Disconnected and vice versa Program Address amp Application This button is used to program the physical address and download the application for the IR Emitter When programing the address the software will prompt you to press the programming button of the IR Emitter After pressing the button the red LED is on Program application This button is only used to download the application When we do not need program the physical address we can push this button to download application for timesaving IR config Click this button the load configure window will appear shown as fig 3 Here is a list of configuration files and at least has one record otherwise appear a alarm shown as the down right figure Select a configuration file and click the Load button the corresponding function configuration window will appear shown as fig 4 If Click the Cancel button the software will back to the window of the first configuration file When import other configuration file the information will be updated in the group address area and the function area immediately GYS K BUS KNX EIB IR Emitter and IR Learner Load Configure smart home Can t Delete the Last configuration At least has one record F
3. and display Connections Temperature range Mounting Dimensions Weight Green LED flashing EIB KNX Infrared emitter cable Operation Storage Transport Flush mounted the IR Emitter the IR Learner 0 05kg IR Emitter and IR Learner Bus connecting terminal black red Indicate the device running normally OK lt 10m OG 25 GC SE 25 C 70 C In wiring box 60mmx60mm or 86mmx86mm 46mmx46mmx 11 7mm 52 5 mmx 18 Immx9 3mm 3 Dimension and Circuit diagram 3 1 Dimension diagram 11 7 mm lt 4 3 2 Circuit diagram XN X D KNX EIB bus terminal v xt K BUS BTIS 04 00 1 A 46 0 mm gt O O ET Er Aer N X IR Emitter T gt 46 0 mm E j a hol ill Fig 1 IR Emitter BTIS 04 00 1 wa x x E Red LED for entering the physical address green LED for application layer normally work GVS K BUS KNX EIB IR Emitter and IR Learner 8 Programming button 4 Connectors for Infrared emitter cable op Fig 2 IR Learner BTIL 01 00 1 USB commnication port Q IR detector When learning please put the IR emitter on the remote control near to IR detector on the IR Learner as close as you can 4 Instructions for the PC software If you want to know all the functions about the IR Learning you will need a PC which connect to EIB KNX bus via KNX downloader the IR Emi
4. ewitchbd C N ri A yawinglo A yawinglT A varlngl A ee i or Fig 4 The function configuration window 4 2 1 Channel You can view the functions of current channel via selecting the corresponding channel or give the channel configurate functions Each channel can be assigned 16 group address at most and the channels 8 GYS K BUS KNX EIB IR Emitter and IR Learner are independent each other If assign exceeds 16 group addresses to a channel the error as follow will appear 4 2 2 Group address area Here shows the detail information of each group address such as function datapoint type etc These information can be configurated in function address assignment area Clicking the right mouse button in the group address area the menu command as follow appears Delete Group Hew Configration Load Configration Delete Configration Fig 5 New configuration file Delete group To delete selected group address New configration This command is used to add a new configuration file as shown fig 5 dialog box prompting you input the name of a configuration file After save a blank function configuration window will appear as shown fig 4 but there is no data on the function area and group address area Here can add up to 16 configuration files Load configration This command is used to load a configuration file as shown on fig 3 You can select the file in the list to import Delete configration To d
5. function configuration window 4 Inthe function configuration window assign a group address communication type and so on to a learned IR function After configuring well click the download button the software will back to the start window 5 In the start window assign a unique physical address to the IR Emitter and then program it and download the configuration file program application to the IR Emitter 6 After finish above steps send a corresponding telegram to the IR Emitter via other bus devices When the IR Emitter receives the telegram it will send the relevant function to the IR device and the IR device will execute the corresponding action Attention 1 For current version due to have not import export configuration file function yet 14 GVS K BUS KNX EIB IR Emitter and IR Learner you have better back up the mdb file on the program path in advance to avoid lost the configuration files in the software by incaution delete 2 Don t send telegram to the IR Emitter frequently or the telegram cannot be recognized and cannot respond to the bus on time by IR Emitter and lost 15
6. to the KNX standard Datapoint In the option box you can select switch Ibit or scene Ibyte If selecting switch Ibit you can recall different functions from all channels via the Ibit object receiving a telegram 0 and 1 If selecting scene Ibyte you can only recall different function from the current channel via 1byte scene object scene number 1 64 corresponding to telegram 0 63 Object function To name the object function will be recalled When switch 0 If switch Ibit is selected in the datapoint the option box is visible Here you can select a function to be recalled when the object receives a telegram 0 All functions in the function area are visibled in the option drop down box When switch 1 If switch 1bit is selected in the datapoint the option box is visible Here you can select a function to be recalled when the object receives a telegram 1 All functions in the function area are visibled in the option drop down box When these parameters have been finished configuration clicking the button Add amp Modify then the configuration information will be added to the group address area In the group address area via double clicking an object the name of object function can be modified in the function address assignment area Via clicking the button Cancel back to start window as shown on fig 1 4 2 4 Function area Here list all learned IR remote control fun
7. Ne lt T Guangzhou Video Star Eletronnics Co Ltd K BUS IR Emitter amp IR Learner User manual Ver 1 BTIS 04 00 1 BTIL 01 00 1 Intelligent Installation Systems http www video star com cn GVS K BUS KNX EIB IR Emitter and IR Learner Contents 1 General o 0 3 1 1 Product and functional overview HRA KEN HE 2 Technical data m m e 0 0 0 0 0 2 4 2 1 The IR Learner 4 2 2 The PC Software 4 2 3 The IR Emitter 4 3 Dimension and Circuit diagram 5 3 1 Dimension diagram 5 3 2 Circuit diagram
8. ction the channel and scene of the function IR transmitting frequency pulsecount send times and slave function In the function address assignment area you can assign a group address to each function Clicking the right mouse button in the function area menu command as follow appears Add Hew Modi fy Show Delete Add new To add a new function as shown on fig 6 Modify To select the function to be modified then you can modify description of the 10 GVS K BUS KNX EIB IR Emitter and IR Learner function send times current detect send delay and slave command list but can not modify the main channel and main scene as well as the IR learned control code Show To select the function to show then you can see the detail information of the function Delete To select the function to be deleted If click it the tips as follow will be popuped you can chose to delete or not to delete the function The title bar in the function area Channel Channel and scene number like C1 S2 Function Function description of a learned IR remote control code Frequency IR transmitting frequency Sendtime IR transmitting times Plusecount IR pluse number Attachcmd slave function All information in the function area can be configured in fig 6 Each function can be configured 64 functions at most so there are Max 256 functions in the function area for 4 channels Meanwhile each main function can attach up to 5 slave functions wh
9. de area will display the control code information of the function key such as frequency pulse count Meanwhile the button Learning changes back to Learn Test To test the control code information of the function key and ensure that it is effective Now you need to place the IR detector of the IR Learner in areas that the IR device can detect normally and to click the button Test If the IR device has action and the action is the same as the function of the key that means the IR Learner has learned successfully the function of the key If the IR Learner does not successfully learn you need to repeat the above process Configuration To config the parameters such as channel scene number slave function send time send delay and function description etc of the control code information of the function key After finished configuring well to click the OK button the software will back to the window of the function configuration and the information of the function key 12 GVS K BUS KNX EIB IR Emitter and IR Learner is saved to the function area If clicking the Cancel button the software will also back to the window of the function configuration but the information of the function key is not saved In fig 6 Main configuration parameters as follows Main channel To assigns a channel to the function of a key Main scene To assigns a scene number to the function of a key Slave channel To select a chan
10. des of the IR remote controller Attention When learning please put the IR emitter on the remote control near to IR detector on the IR Learner as close as you can within 3cm to avoid the failure of learning The IR Learner is provided with receiving and emitting IR function so it can test and verify whether the learned control code has been learned correctly For convenient to operate suggest that connect the IR Learner to PC via a USB extension cord please 2 2 The PC Software System requirements windows XP or above operating system don t need to install driver Operating environment Install falcon ETS3 or ETS4 software on your PC first so the PC software can run directly and does not need to be installed Meantime there also need install Microsoft Office Access software on your PC or you cannot configure functions 2 3 The IR Emitter The extremely compact design enables the IR Emitter to be inserted into a conventional 60 mm or 86mm wiring box Attention the Infrared emitter of the IR Emitter must be installed in range that the IR device can detect normally to avoid no action Power supply Bus voltage 21 30V DC via the EIB bus Standby current lt 8mA Dynamic current lt 20mA Power consumption lt 240mW Output Channel Number 4 Channels Max transmitting distance 2m IR wavelength 940nm IR emission amp receiving angle lt 45 Operating Red LED and button For assignment of the physical address GVS K BUS KNX EIB
11. elete the current configration file The title bar in the group address area Groupaddress Display the group address of functions Datapoint Display the datapoint type of recalling functions gt DPT Switch 1IBIT or DPT Scene 1BYTE Function Function description or object function name Value 1 It is available if the datapoint type is DPT Switch 1BIT When the object receives a telegram 1 the corresponding function is recalled Value 0 It is available if the datapoint type is DPT Switch 1BIT When the object receives a telegram 0 the corresponding function is recalled Scene It is available if the datapoint type is PT Scene 1BYTE When the object receives the scene number the corresponding function 1s recalled Sign X means that the datapoint type is not recalled or the function has been deleted in the function area Sign means that the functions are recalled via scene GVS K BUS KNX EIB IR Emitter and IR Learner Cx Sx XX Cx Channel number Sx Scene number XX Function description in the function area 4 2 3 Function address assignment area Here you can assign a group address to each function and you can also set the datapoint type of object as 1bit or 1byte Main configuration parameters as follows Assign group address In this textbox you can assign a group address to the IR control functions in the function area There is the group address format on the right side it conforms
12. er The IR Learning can be used for learning control code of the IR Remote Controller and storing the code to the database in the PC software The learned control code can be stored deleted or tested in the software The IR Emitter has 4 channels Usually we use one channel to control one IR Remote Control device The IR Learning can learn up to 64 functional control codes for each channel The IR Learning is consist of PC Software IR Learner and IR Emitter The PC Software is used for config the functions like physical address group address scense call etc IR Learner is connected to the PC via USB interface and used to learn the control codes of the keys of the IR Remote Controller The learning process is realized by operating the software and you should put the IR emitter on the remote control near to IR detector on the IR Learner as close as you can to avoid the failure of learning The IR Emitter is connected to the EIB KNX bus dirrectly using the EIB bus connection terminal As the configuration has been finished the PC software can download the learned control code to the IR Emitter via the KNX downloader which has been connected to the KNX EIB bus After success to download the IR Emitter can control the switch wind speed and timing of a fan as well as the IR remote control devices such as DVD TV Air Condition Fan etc through sending telegrams on the KNX bus by other devices in the EIB KNX system This manual provides detai
13. ich scene number must not to be the same as the main function s 4 3 Learning IR function To learn the control code of common function of IR remote control as shown on fig 6 Here can learn and configure all information for the function area via a IR Learner Clicking the button Learn in fig 4 you will open the following window and learning the functions of IR remote control 11 GYS K BUS KNX EIB IR Emitter and IR Learner HE Video Star IE Learn Assign Channel And Scene No Main Channel Channel I Slave Command List MAX Hum 5 Channel Secene H0 01 Channel 2 Seene HO 02 Main Scene Scene HO 63 Slave Channel Channel zl Slave function area Slave Scene Scene NO 2 Add Slave Del Slave Send Time v Send Delay 0 vw 100ms Function Current Sense Wo Detect if Correct Wave 1666 0562 0562 0562 0562 0562 0562 0562 Function code area of IR remote control oo 0582 0562 0562 0562 0562 0562 0562 IBRA SAS 1688 NGR IE Tool Connected Carrier Frequency URW Fig 6 Learning IR remote control function window The step that the IR learner learns a function of the IR remote control is as follows l Learning Click the button Learn right now the button becomes Learning then put the IR detector of Remote Controller as near as possible to the IR detector of the IR Learner and press the function key of the IR remote control then in fig 6 the function co
14. ig 3 List of configuration files a kep one tecon 4 2 Function configuration window The function configuration window is shown as fig 4 Here you can assign a group address to a learned IR remote control function Via the group address the IR Emitter can communicate with other devices on the bus Meanwhile you can recall these functions via 1bit or 1byte datapoint type HE ideo Star IR Tool smar el 2i 13886 JM Biel Gham E 0 0 1 DFT Switch 1BIT 15 7 255 DFT Switch 1BIT Value ci Sl ci Sl switch Ci E switch A switch saa E l A switchi switchi J940000000068 DFT Scene 1BTTE Scene l x ki elass switch DFT Switch 1BIT IPT Switch 1BIT IPT Switch 1BIT DFT Switch 1BIT DFT Switch 1BIT IPT Switch 1BIT DFT Switch 1BIT IFT Switch 1BIT IFT Switch 1BIT TFT aana 1TAYTE switch class time class time time switch yaring switch switch yaring switch switch TATT aa C4 Si C4 564 a c3 31 c3 31 ce 564 switchl E timel D switchb4 I yawingl yawingl switchb4 E Cl S16 yawingl6 c3 81 C4 564 ce f 564 Ci S64 C4 SI C3 S64 C3 S64 ce Si ci 310 x yawingl switet switet classe timel I switet switel speedl MI0000000000 Assign Group Address 0 02 switchl switche switche switchs switch switchs switch then Switch 1 yawingl C Add amp Modi fy FA A IN A
15. led technical information about the IR Learning for users as well as assembly and programming details and explains how to use the IR Learning by the application examples The functions of the IR Learning are summarized as follows gt Achannels gt Learning and storing up to 64 different IR functional control codes for each channel gt sending time and sending delay can be set for each control codes gt each main function can include 5 slave functions this way is suitable for controlling several functions via one object at a time gt You can set the emittion times and the delay time before sending for each function code gt A channel can link up to 16 group addresses gt The IR functional control codes can be assigned to 1bit or Ibyte type of object gt bit object can recall the control codes from all channels gt lbyte object can recall the control codes from its own channel gt The IR Learner uses a common USB port to communicate it is easy to learn the functional control codes of the IR remote controller and store the codes to the database of the PC Software GYS K BUS KNX EIB IR Emitter and IR Learner gt Can learn more than 95 of remote controllers in the market Each channel can take over all of the functions described above 2 Technical data 2 1 The IR Learner The design of the IR Learner is as a UDisk small and exquisite in size The IR Learner is needed to use only when it learns the functional control co
16. mitting of the pivot and time function Then when the IR Emitter receives a corresponding telegram the IR Emitter will first send the turn on function signal to the fan after a while send the pivot function signal to the fan and then after a time send the time function signal to the fan in order to protect the motor of the fan Function To give a learned IR remote control code add Function description Current Sense Before sending the function code the IR Emitter whether detects the current on the IR device There are three type No Detect The IR Emitter will not detect the current of the IR device when it receives a corresponding telegram and it will send the corresponding function directly to the IR device No Current to send The IR Emitter will detect the current of the IR device when it receives a corresponding telegram if there is not current it will send the corresponding function to the IR device vice versa 13 GVS K BUS KNX EIB IR Emitter and IR Learner Have Current to send The IR Emitter will detect the current of the IR device when it receives a corresponding telegram if there is current it will send the corresponding function to the IR device vice versa For example The current sense is used for controlling a TV Due to turn on or turn off the TV it uses the same control code Now you want to turn on the TV and the current sense is selected with No Current to send if the TV has been turned on it will no actio
17. n or else turn off the TV Now you want to turn off the TV and the current sense is selected with Have Current to send if the TV has been turned off it will no action or else turn on the TV Attention current version has not supported this function so select No Detect please Correct wave To correct waveform of the code for NEC Philips Panasonic Sony and other code correcting them to theoretical cycle and duty cycle to reduce the error in the leraning process By default the parameter is selected If the test of the code can not pass when the correct wave is selected you need to cross out the option and then learn the code again 4 4 Build a new configuration file The main steps that build a new configuration file as follows 1 The IR Learner is connected to a PC the IR Emitter is connected to the EIB KNX bus system start the PC software and come to start window set the KNX communication interface and connect 2 Open a default configuration file enter the function configuration window Click the right mouse button in the group address area select new configuration to build your own configuration file 3 Click the button Learn in function address assignment area enter the learning IR function window here you can learn your required function and test it if test OK configure relevant parameters to it see chapter 4 3 Save the function via clicking the button OK and the software will back to the
18. nel for a slave function Slave scene To select a scene number for a slave function Add slave when a slave function has been assigned a channel and a scene number you can add the slave function to the slave function aera via this button Each main function can attach up to 5 slave functions and the 5 slave function can be found in the function area otherwise no action For example you want to turn on a fan and let it pivot then when you configure a on function you can attach a pivot function and meantime you can also attach an open TV function etc but the pivot function and the open TV function also need to be learned in advance via the IR Learner and saved to the function area Del slave To select the slave function to be deleted in the slave function area and click the button then the slave function is deleted Send time To select the send times for example the wind speed function of a fan is set to 2 times for transmitting then when the IR Emitter receives a corresponding telegram the IR Emitter will send the wind speed signal to the fan and repeat 2 times then the wind speed of the fan will jump 2 steps Send delay 100ms To set the send delay for the control code of a function referred to as function signal For example you turn on a fan and attach a pivot and time function If they are executed at the same time this may influence the life of the fan motor so you can delay a period of time for trans
19. tter which connect to EIB KNX bus system via a KNX interface and the IR Learner which connect to the PC via a USB port and run the PC software to learn and configure the functions of the IR remote control device and download these functions to the IR Emitter 4 1 Start window Start the program GVS KNX Tool exe in the directory Knx IRTool2 the software operating window is shown as fig 1 MA Video Star KNE Tool E Fhysical Addr it 1 1 Open Connection Verify Mode IR Learn Control Area rogram pgram Application IR Config Status Enx Disconnected GYS K BUS KNX EIB IR Emitter and IR Learner Fig 1 Start window Physical Addr Here can be used to set the physical address for the IR Emitter the format is XX XX XXX Open connection Click this button the ETS connection manager window will visible shown as fig 2 Here can configure the KNX communication interface such as USB RS 232 standard RS 232 FT1 2 IPCEIBlib IP KNXnet IP KNXnet IP Routing it is similar to the ETS tool software The KNX communication interface that you select must match the interface of the downloader to be connected in the EIB KNX bus system otherwise the PC software can not connect to the EIB KNX bus system After configuring successfully the status bar displays Hr Tool Connected ETS Connection Manager Acer anise tt Serial PEIG COM1 ra lue v EES S ES USBEG Fig 2 ETS Connection Manager
Download Pdf Manuals
Related Search