User's Manual of Laser Engraving Cutting Embedded Software
Contents
1. If you not check move from origin then the offset means the offset to the current position The X axis for example assuming the current position is 100mm such as the step distance is set to 10mm then the exercise once the new location will be 110mm such as the check moves from the origin movement time the new location will be 10mm and repeated Movement location will no longer change Note According to the provisions of the controller the absolute position is no negative in the whole breadth If you check the Move From Origin and set the offset value negative then the machine will hit limiter 3 6 Info Export General Machine Document Manual Info Config Vendor password a o Information on the operation of the motherboard manufacturers need to enter password to view parameters Export General Machine Document Manual Info Config Total on timefhour minisi Po Total processing timefhour min si es Previous processing timethour minisimsi nn Total laser on tinethour minis Po Tokal processing times iE nea x Total travalim E Y Total travelimh e as 1 gt Total on time The total time of motherboard working 2 gt Total processing time The total time of processing including the time of jump moving 3 gt Previous processing time The time of the last processing 4 gt Total laser on time The time of the laser processing 5 gt Total processing times The number of completed pro2. Export Precision velocity Unit mms ae oe lt 4 2S Language 2 4 Object Selection In the process of drawing and edit graphics first of all is to select the object When the object is being selected in the center of this object will have a shaped mark X 22 and surrounded by eight control points Click menu Select switch to status Select Under this status you can select object The following are five kinds of method of selecting Shortcuts Ctrl A select all objects Click mouse on the screen to select single object ag J g Select object using select box Press the mouse and drag as long as the box come into contact with the object will be selected Increased select object minus select object Increase select Press Shift key click or box select to increase select object Minus select Press Shift key click or box select the selected object Select object according to layer Speed MinPower MaxPower Output 100 0 30 0 30 0 Ves 100 0 30 0 30 0 Yes 100 0 30 0 30 0 Ves 100 0 30 0 30 0 Ves Right click the selected layer then the part of all objects in the layer will be selected 2 5 Object Color The color of object that is the color of the object contour You can click the color button on the Layer Bar to change the color of the object has been selected The color of the pressed button is the color of current layer 2 6 Obje
3. G0 scale mode Close laser Go scale blankfmm 0 000 Go scale mode Points of light to go off the border the opening cut borders corners three modes Go scale blank Walking frame can be based on the actual image size up and down again about the direction of some of the white left side of the border in order to ensure complete contains the actual graphics This setting is on the control panel to go with the border related functions while walking on the border with the independent software 3 3 5 Other parameters other parameters Array processing Bi dir Array Return position Absolute Origin Delay before feedis 0 000 Dealy after feedims 0 000 Focus depthtrmme 0 000 Backlash ror 0 000 Backlash imm 0 000 Array mode you can choose the swing mode and the one way mode The Swing mode cutting the array back and forth in order the One way mode always cutting the array from one direction to another If One way mode is selected all array units have the same movement modes and the same liquidity of movement however this mode will take more time than the swing mode The default mode is the Swing mode Return position You can select the locating point and the machine origin This parameter decides the position the locating point or the machine origin where the laser head stops upon completion of each operation Delay before feed Using the feeding device the delay before a single feed users can arrange the time and the lik
4. If the arrow appears in the upper left corner coordinates and the origin in the upper right corner of your machine you just need to check both the X mirror 3 3 7 Position of Laser Head Position of Laser head means the location laser head relative to the graphic Top Left Top Middle Top Right Middle Left Center Middle Right gu 00 are Bottom Left Bottom Middle Bottom Right when you intuitive view just look at the zone where the green point appears 3 3 8 Absolute Coordinate You can directly check this option when you want the graphics location in the graphics display area correspond to the actual work location of processing Then the graph position will no longer relate with the actual output position of the laser head and orientation point but always regard mechanical origin as the anchor point 3 4 Document Management Export General Machine Document Manual Info Config Number File Mame Tired HM SMS Delete Delete All Download Upload Read Process Cal time 1 gt Read Click button Read the software will communications with the controller read the list of files on the controller After read controller successful file information will be displayed in the document list 2 gt Download Click button Download will pop up the file dialog select rd downloaded file then the file will be downloaded to the controller If the download is successful the docum
5. BD too Simulate colori Power o A A oo Idle color P Anchor Top left Top right Bottom left Bottom right You can preview the color of graphics to match the actual output of energy Users can easily view whether the layer energy is true Chpater 3 System Settings Before output graphics required to determine whether the system settings are correct 3 1 Output Setting Export General Machine Document Manual Info Config Path optimize Original or edit path Enable rotate engrave Order of layer Inside to outside Diameter rom zo Auto determine start point and dir _ Auto Find start point Circle pulse jooo _ Backlash reapy optimize Block handle Height Dir Up to bott d Linejcolumn setup Feeding Count lo s Mum sspace mmi p Distance mmi Bo Mur Yspacetram o Position Aaaa Bestrewing breadth nH Qutput select graphics 3 1 1 Path optimize 1 gt Original or edit path Selected by the original path or edit the path press the original drawing graphics output to the machine processing the order If the order by layer from inside to outside and other optimization methods are useless Generally do not choose the property in a very large number of graphics output the choice of this property without having to wait for the software algorithm processing time 2 gt order of layer The list from top to bottom layer by layer order
6. Speed Power Progress BAAADODAODODONDNI Default J v Pause Continue Stop Simulate Software supports the preview of the documents to be processed and you can get some basic information through the preview For example the path of the actual output of the processing general processing time processing the distance The machining process can be simulated In addition to the current edited file preview you can also preview the files have been saved as rd 1 gt Preview rd file Double click in the graphics display area Choose the graphic you want to preview in the pop up dialog box And then open Look in Lj My Documents gt Fi e fal 9 4dobe Scripts My eBooks Source Insight Baidu _ My 150 Files Visual Studio 2008 IC Corel User Files my Music fem Esa ae eal FILTERIT4 User Settings Emy Pictures e5DStore My Q9 Files my Designs a my Webs File name Files of type od Open as read only 2 gt Software also supports to set the parameters of preview Right click Anywhere in the graphics display area the configuration menu will appears Select Config pop up following dialog box Full window Contizuration Conti i Background Heri zontal mirra Back color E Font color o Vertical mirror Draw colori Power w OT E
7. changing with drag scaling Apply to view Current settings is only used for preview without affecting to the original bitmap press button Cancel bitmap will returned to the state of original image Therefore only use for adjust effect However this approach requires more time and memory Space Apply to source Current sttings is use for orginal bitmap directly so even finally click button Cancel image will also unable to return to the original image Therefore it mainly used in multi step operation and the current operation of this step 1s necessary to do such as general pictures must be transformed into grayscale This can save the computing time of the follow up operation Save as Retain the results of the previous operation In addition to using Apply to view can also be exported On this basic to facilitate subsequent processing Gray scale Generally other image processing is based on the grayscale so before handling you can do a grayscale processing then click button Apply to source For the grayscale than the color image occupied smaller memory for large image step by step handle to a certain extent to avoid the lack of memory For color image adjust contrast and brightness have some auxiliary effect to following dither processing Adjust contrast Before processing After processing Invert Before processing Sharp E S Wal FN gt AIT REE wwew 61tu com Before processing
8. followed by the output layer to the machine processing Generally do not choose to not in front of check by order of the output layer 3 gt Inside to outside If there are other graphics within the closed graph then the first cut and then finished cutting all the graphics inside the closed graph 4 gt Auto determine start point and dir If not checked then do path optimization only adjust the order of graphics processing cutting starting point and the cutting direction to remain at the original graphics processing 5 gt Auto find start point Using the change function the graph from the closure point to find a more ideal start cutting For special processes such as cut glass choose this in general do not choose 6 gt Backlash repay optimize When the machine there is space such as dislocation of the seal cutting graphics can be checked in general do not choose 7 gt Block handle Block height for the different graphics to set a different height values there is no rule for the arrangement of the graphics height generally between 10 20mm set Block processing needs can choose the direction from top to bottom from bottom to top from left to right or right to left For a regular arrangement of graphics if you want to achieve the desired cutting sequence you must set the appropriate height Generally high altitude take a single line graph as the block height 3 1 2 Array Setting Array processing setting is f
9. number 2 3 File parameters setting PLT Precision According to the accuracy of the original plt file to select the appropriate import unit Smooth curves When import vector file automatically smoothing the original curves For the original graphic is smooth or need to repeatedly adjust the beset smoothing effect you can uncheck this button Do not do smoothing curves may reduce time of import processing Auto close curves According to close tolerance automatic check and closed curve Combine lines According to merger tolerance auto connecting curves Color map automatically switch to grayscale Because under normal circumstances graphics are based on grayscale If the imported bitmap is a color image can be converted to grayscale Import Dxf text info When the user need only Dxf the graphic information not need the text information within the file do not check this Dxf Unit The default dxf unit of software is MM Users can change it to CM inch and custom Export precision The precision of export output file rd format Velocity unit Software supported two types of speed unit mm s m min Selected according to usage After it was selected the speed of parameters on the interface unit will change with it Export General Machine Document Manual Info Config Auto close curves Close error rom Combine lines Combine errorimm Inport Oxf text info DsF Unit Export Setting
10. selection the general mode and the special mode in the general mode there s no any treatment during the scan in the special mode light spots will be treated If the special mode is activated the power of the laser should be increased and correspondingly the light spot percentage will be lower and the laser power attenuation will be higher to achieve the same depth of scanning the laser power should be higher The purpose to select the special mode is to make the laser to emit beams at high power and in short period during deep scanning the effect of flat bottom can be achieved however if the light spots are improperly adjusted this effect may not be achieved and the working mode of high power and short period may influence the service life of the laser The default mode is the general mode Facula Size When scanning the general pattern of selection the argument is invalid when you select a special mode the onset of the parameters Control the parameters of control in 50 to 99 respectively 3 3 3 Home parameters KH Home para Home speedimm s 80 000 Auto home x Yes Auto home r Yes Auto home z Mo Auto home lJ Mo Home speed This parameter determines the machine is turned back to the origin when the speed of a larger format 1f the machine can be set to reset the speed is too large but not too much X Y Z U Auto home The axis can be set whether should reset at boot time 3 3 4 Go Scale parameters H Go Scale para
11. 50 99 98 000 x Start Speed y Start Speed Off scanning speed in the use of stepper motor drag do not began to accelerate from 0 but can start work directly from a speed to shorten the overall processing time but the speed is not too high and because the X Y axial load is different from the rate general the initial speed of X axis slightly higher than the initial speed of Y axis x Acc y Acc With the scanning speed the speed of layers in the layer parameters to match if set too small the scan speed to a longer distance the scanning efficiency The machine can be set according to the actual structure load conditions vary Since X Y axis load generally much higher than the X axis Y axis accelerometer Line shift speed of scanning this parameter is specially used to control the max speed of the scanning to shift vertically from one line to the next line below it If during the scanning the line space is too large or the block space is too large when scanning block figures while precise positioning for each line or block is required you can set the line shirt speed of scanning to a comparatively low value This parameter cannot be less than the jump off speed of the corresponding axis during the line shift and cannot be higher than the max speed of the corresponding axis during the line shift if the setting is illegal the controller will automatically set this parameter within the range above Scan mode There are two modes for your
12. After processing There are three method for dither processing Net graphic Dot graphic Black and white 1 gt Net graphic Net graphic need adjust net size better suited to material which is not high resolution or the laser is relatively slow to respond To get the appropriate net size you can adjust resolution and net frequency of the image The higher resolution the more delicate The higher net frequency the smaller net size The lower net frequency the bigger net size Generally resolution of image is 500 1000 and net frequency is 30 40lines aba ee eee vz tree eee were ee sa RE trarahat giji 10s Aah 2 gt Dot graphic Dot graphic performance of good grayscale and the laser responds fast 3 gt Black and white In most cases the effects of color image into black and white image is poor however for some clear outline image is very easy to use The aes Eos te Get outline Eitmap handle Width Pixels Height Pixels H Resolution 36 Pixelssinch Y Resolution 36 Pixelsfinch Brightness 0 0 saa Contrast 0 0 aa e Invert color Set output resolution Resalution pixelstinch Dither Met graphic Frequencytlinesfinch Dot graphic Black And White Gray scale Sharpen Apply bo wiew Apply to source Get outline 2 12 9 Processing preview Click menu Preview Size Total time Light time Idle interval Work interval Position
13. Remove backlash Right click scanning reverse gap block in the backlash to delete the item then click the Delete button 3 3 Machine parameters Export General Machine Document Manual Info Config Son Idle speed mmys 300 000 Axis s Mirror Idle Acc mm s2 2000 000 Axis Y Mirror Start speed rnm ss 15 000 l Laser head Min Accimmisz 500 000 Max Acctrim s2 000 000 Ue Cutting mode Normal Cutting F F A Acc Mode 5 mode x Start Speedimrny s 20 000 Absolute coordinate v Shark Speedimmis 15 000 3 3 1 Cut parameters H cut parameters Idle soeed mmis 300 000 Idle Accimmis2 2000 000 Start soeedimm is 15 000 Min Acctmmys2 500 000 Max Accimmisz 2000 000 Cutting mode Normal Cutting Acc Mode S mode Idle speed this parameter decides the max speed of all lines not emitting beams during the operation of the machine This parameter should not be lower than the lower of the jump off speed of the X axis and that of the Y axis and not exceed the higher of the max speed of the X axis and that of the Y axis if the setting is illegal the controller will automatically set this parameter within the range above a comparatively high idling speed can shorten the operation time of the entire figure while excessively high idling speed may cause dithering of the tracks therefore you should take all relevant factors into consideration when setting Idle Acc Corresponds to the acc
14. User s Manual of Laser Engraving Cutting Embedded Software RDCAM6 0 Chapter 1 Overview 1 1 Laser engraving cutting system introduction Laser engraving cutting system through a computer numerical control machine tools to achieve effective control according to the user s different requirements of the completion of processing tasks The system including control board and control panel and supporting software This manual describes how to use the software to complete the task of laser processing Motherboard wiring and control panel operations see the accompanying manual and control panel wiring board operating instructions 1 2 Environmental requirements 1 WindowsXP operating system and above XP recommended 2 Above CPU586 above PIII or PV recommended 3 Memory above 1G recommended 1 3 Software running Embedded software can be embedded in CorelDraw AutoCad CaDian2010 and Illustrator CS5 software the software is similar to the operation embedded software installation methods please refer to lt lt RDCAM software Setup Manual gt gt 1 3 1 Run CorelDraw 1 gt Run CorelDraw 2 gt Import graph to CorelDraw or draw some graphics oa 3 gt Click toolbar button then RDCAM running 1 3 2 Run AutoCad 1 gt Run AutoCad 2 gt Import grahic to AutoCad or draw some 3 gt Click toolbar button Q then RDCAM running 1 3 3 Run Cadian2010 1 gt Run Cadian2010 2 gt Import grahic to Cadian or draw s
15. acilitate used to treatment array processing of graphics X Num and Y Num correspond to the rows and columns of the array X Space and Y Space correspond to the rows spacing and column spacing of the array H represent the distance of the graphic edge represent the distance of the two graphic center Adjust the X space Y space more closely the graphical layout click the plot area so that graphics are not selected then the arrow keys on the keyboard to adjust and roll the mouse to display the zoom so the adjustment interval process more accurate Bestrewing Breadth Setting According to the size of frame and current array settings to determine the maximum number of columns X Num and rows Y Num Click button Bestrewing breadth the following dialog box appears Hestrewing breadth x X breadth imm Y braddth mm 800 Click OK software can automatically calculate the appropriate numbers of rows and columns 3 1 3 Rotate Engraving Enable rotate engrave After enable engraving the actual precision of Y axis will be based on diameter and step per rotate to auto match the setting of pulse precision of Y axis In addition the work area in the main interface will also change Diameter The diameter size of the parts Step per rotate The number of pulse corresponds to the workpiece rotate one week The function is to facilitate the users to replace parts and different size of the workpiece when the wor
16. ame as cut in lines 2 12 3 Curve Smooth For some less accuracy curves this function can make curves more smoothness and processing smoother Click menu Tool gt Curve Smooth the following dialog box appears Curves smooth Smoothness 95 Direct smooth a rn oe Cee Drag the smooth slider and click button Apply before smooth and after smooth curves will all show in the dialog The black curves represent the original curves and the red curves represent after smooth Curves Curves smooth Smoothness J 95 Direct smooth a re CR Cee You can view the graphics with drag mouse You can zoom in zoom out the graphics with scroll wheel Click button FullFrame graphics will shown in the dialog box for largest After get satisfied smoothing effect click button Apply curves will processing smooth according to smoothness settings Select Direct smooth you can use another smoothing method The choice of smoothing method should be changed with the needs of the actual graphic 2 12 4 Check Closure Click menu Tool gt Curve auto close the following dialog box appears Setting close error Close error mm t Force to close cme Close error When distance from the starting point to ending point less than close tolerance automatic closing of the curve Force to close Mandatory closure of all selected curves 2 12 5 Rem
17. ample the laser head emits laser when scanning from right to left but not emits laser when scanning from left to right X_swing The laser head emits laser and scans figures back and forth horizontally Y_unilateralism The laser head scans figures back and forth vertically but only emit laser toward one direction For example the laser head emits laser when scanning from the top down but not emits laser when scanning from the bottom up Y_swing The laser head emits laser and scans figures back and forth vertically Note We generally adopt the scanning mode of X_swing Interval The interval between the current line and the next line to be scanned by the laser head The smaller the interval is the darker the scanned figures is If reverse the weaker Recommendation The scanning interval is set below 0 1mm for vector layer color layer in general The scanning interval is set above 0 1mm for bitmap layer BMP layer in general and then the Minimum power and Maximum power should be changed to attain the perfect effect of the scanned figures 4 4 3 Laser Cut Parameters Setting Eg ra Load parameters From library ayer Ts Output 5 v Speed mmiysi Default IF Blowing Processing Mode Min Powerl o Max Power Layer Parameter Seal cutting has not closed the graphics appear the case is closed you can compensate with the seal to close but if the seal is misplaced you can not compensate you
18. ath RDCANG 0 01 x 600 000 mm fe 611 724 mm 100 1 4 Layer Mode Speed MinPFower MaxPower Output y 399 999 mm T 394 038 mm o c s Har b Cut 100 0 30 0 30 0 Yes Export General Machine Document Manual Info Config Path optimize Original or edit path Enable rotate engrave Order of layer Inside to outside Diameterimm o Auto determine start point and dir l C Auto find start point Circle pulse ooo Backlash reapy optimize Block handle Height Dir Up to bott d Line column setup Feeding Count P x Mum Mspace mm b Distanceimmi soo Y Mum Yspacefmm b Position Ssa USE Auto Start Pause Continue Save oUFile Bestrewing breadth About C Output select graphics Go scale Cut scale Stop Download UFileQutput f Eo E 1 gt Manual sort Choose the primitive that should be changed the cutting order then the cutting serial number of the current primitive will display in the object properties bar x 138 959 mm f 93 622 mm 100 C 9 Y 64 179 mm 33 231 _ mm 100 c Process WMO e oo Enter the serial number directly in the processing number then press the keyboard Enter key or click the plot area the cutting order will be changed 2 gt Change the processing direction Click Cut property gt Set Cut Direction to enter the edit mode of the cutting direction Then you can double click on any position on the se
19. can use 4 9 5 optimization backlash compensation to compensate or to use the user parameter in the Backlash compensation Seal 0 000 mm Open delay Open Delay Do e ms Close Delay 0 Close delay t Throughaode Advance Through mode Using the slit width compensation can compensate for the offset between the graphics and the actual output graphics that caused by laser cutting It only has effective for the closed graph Direction Compensation direction is set according to actual needs such as cutting a circle if you want to retain the cutting down of the circle you should set out the direction of compensation If you want to keep the hole should be set to compensate for the inward direction Sew width it is the width of the laser Other cutting param Enable sew compensation Direction Sew width or mm 4 4 4 Laser Dot Parameters Setting Layer Parameter we M Is Output x Ves T Speedimmniy s Default Yes IF Blowing Processing Mode Bot Advance Min Powerl o Max Poweri o The time for emitting laser on one dot during the process The higher the value is the darker Only dot at center Dot time 0 1 5 7 The interval between the dots Dot interval 5 mn Dot length 0 Dot length for cutting dash line F Centecdot Thank you for using the product of Shenzhen Rui Da Technology Co All parts of this note the economic rights of the Shenzh
20. cessing not include the processing forcing to end 6 gt X total travel The total travel of motor X 7 gt Y total travel The total travel of motor Y Motherboard version The version of the current controller The function of upgrades If the board has additional features the manufacturers will provide the update file bin format the user can load the upgrade file to upgrade the motherboard After the upgrade you need to click on the control panel Reset button reset the motherboard before normal use Chapter 4 Processing Output Stop Pause Continue Save oUFile UFile utput USE Auta Go scale Cuk scale 4 1 Device port Software supported two ways to link motherboard USB and Earthnet Users click the Device port button and set link type and port in the pop up dialog CO web USB If the computer only connected one device you can set to Auto The software will automatically search the device If the computer connected many devices then first of all you need to click Search After search the connected devices will all add to the drop down list What you need to do is select the specified device Earthnet If the computer only connected one device you can set to default If the computer connected many devices all you need to click Search After search the connected devices will all add to the drop down list 4 2 Go Scale Cut Scale For Example Go Scale As the following figure shown t
21. ch run across the bitmap will not Optimized scan If you select Optimized scan it will adjust users setup of Scanning interval automatically to the best values and optimize the scanning effect Otherwise we should select Scanning interval as set by the user for scanning We generally select the Optimized scanning Output direct On the grayscale bitmap grayscale graphics for the actual output where both the deep color of the laser energy laser energy where light color small Ramp effect If you select Ramp effect it can make the track edges of scanned figures presented as ramp in order to attain solid effect Overstriking Includes Un process Intaglio and rilievi General select Un process Scan the font is the font that is part of the scan which is the font intaglio Scan the bottom of the bottom part of the scan which is the font rilievi Note select the ramp effect set the font bold choose not to deal with Otherwise it will affect the ramp effect Font intaglio the text does not have the outline border It is the text itself that is to be scanned Welcome Font rilievi The text has the outline border it is the figureal base to be scanned please see the figure below We C O m C Scan modes including X_unilateralism X_swing Y_unilateralism and Y_swing please see the figure below X_unilateralism The laser head scans figures back and forth at the level direction but only emit laser toward one direction For ex
22. ct Transformation Transformation of object mainly include object location orientation and size But does not change the basic shape of the object and its characteristics Transformation of object for users provides a convenient user interface You can also use the Object Properties toolbar 531 841 mm Wey 162 197 mm 100 C s m H Y 139 70c mm J 281 255 mm 100 c E You can also use the right transformation tools to transform and copy the graphics 2 7 Place object Place the object is to facilitate the view or position Right click menu functions can be docked in the object will be placed on the page selected several special position upper left upper right lower right lower left and center of the page and if placed in another location you can use the 2 6 object transform feature implementation w Select View Dr aw Cut property Tools Align Docking d F d d d d Top left Top right Bottom right Bottom left Gr op Frevyi ew Center 2 8 Object align Select multiple objects use the alignment tool in the context menu on the selected object to a variety of publishing operations Align the base object Press SHIFT for a single object in turn check for an object to the final choice as a benchmark Curve number for the marquee to the object at the bottom for the benchmark Ww Select View Ur aw Cut property F T F Tools Align Left Docking d Align Right Align To Gr op
23. e such as picking process Delay after feed Refers to the material sent to the feed device in place the need for stability after a period of time for processing Focus depth Auto focus operation to find the corresponding panel Backlash X Y Used to compensate the backlash caused by the machine drive problems 3 3 6 Axis Mirror Layer Mode Speed MinPower MaxPower Output Export General Machine Document Manual Info Config z T T Axis Mirror H Cut parameters Idle speedirmmy s 300 000 Axis s Mirror Idle Acc mm s2 2000 000 9 Axis Y Mirror Start speed mm s 15 000 Min Acctmrmnse 500 000 Max Accimmisz 000 000 Laser head Cutting mode Normal Cutting Acc Mode 5 mode Sweep parameters x Start Speed mrmi s 20 000 v Start Speed mrn s 15 000 bsolute coordinate Pause Continue Save ToUFile E T 0 Generally Axis direction of mirror is based on the actual location of the limit or home of machine The default coordinate system if Descartes coordinate system and zero in the bottom left If the zero point of the machine is top left then X Axis do not need to mirror but Y Axis need to mirror If the zero point of the machine is top right then both X Axis and Y Axis are all need to mirror More convenient way is to view the graphical display area if the location coordinates and arrow on your machine the actual position of the same origin If not then modify the direction of the mirror
24. ee Align Bottom Align Horz Center Preview Align Vert Center Align Center f Arrange space horizontal Arrange space vertical Resire width Resize height Resize size 2 9 Object View The view of the object can be used in the viewer right click menu Translation Click View Move Then hold down the left mouse button in the drawing area drag the pan Marquee view Click View View select Mouse to the drawing area hold down the left mouse button and drag in the drawing area displays a marquee in the dashed box release the mouse were framed in the region will be the largest share in the drawing area to display View page Click View View Page Frame You can view the full page display View data Click View View Data Frame You can view the full selected object 2 10 Group and UnGroup Edit graphics and sometimes need to be a part of the operation as a whole such as multi line text layout Method Select the group of graphics and then select the menu Edit Group UnGroup 2 11 Basic graphics creation Line Click menu Line drag the mouse on the screen you can draw an arbitrary line Press the Ctrl key while dragging the mouse to draw horizontal or vertical line Polyline Click menu Polyline Drag the mouse on the screen you can draw an arbitrary polyline Rectangle Click menu Rectangle Drag the mouse on thescreen you can draw an arbitrary si
25. eleration of the speed of air travel time air and air way way speed of acceleration to match if you set too slow the actual speed may not reach the air way set value if set too fast they may not withstand the mechanical structure resulting jitter Slightly higher than the general acceleration of air way cut acceleration Cutting Acc Corresponding to the acceleration of the speed of cutting cutting speed is the speed of the layer parameters of the layers Turning speed Turning the corresponding deceleration in the cutting process the minimum speed of the drop when processing a lot of teeth when the graphics may be appropriate to reduce the turning speed Turning Acc Should match with the turning velocity Cutting mode Split precision cutting fast cutting ultra fast cutting the user can choose according to the actual applications Such as the emphasis on accuracy select the precision cutting such as emphasizing speed select the fast cutting Acce mode this parameter decides the acceleration and deceleration mode S mode or T mode of the motor during operation the motor accelerates and decelerates slowly and smoothly in the S mode and fast and relatively unsmooth in the T mode the default mode is the S mode 3 3 2 Sweep parameters Sweep parameters x Start Speedimmis 20 000 y Start Speedimmisi 15 000 x Acctmmiys2 5000 000 y Acctmmiys2 2000 000 Line Shift Speed imm 150 000 Scan Mode Common Mode Facula Size
26. en Rui Da Technology Co Without our approval no unit or individual shall not reprint copy or distribute the content related to this product manual If the product content information to change without notice Users who have any comments or suggestions in the process of using the instructions please call Phone 0755 26066687 Fax 755 26982287 Address Building 2 501 Nan You Tian an Industry Park Nanshan District Shenzhen City Website www rd acs com
27. ent list will update 3 gt Process Select the file to be processed from the document list and click button Process The controller will start the specified document 4 gt Delete Select the file you want to delete from the document list and click button Delete The controller will delete the specified document If the deletion is successful the document list will be updated 5 gt Delete All Automatically remove all file in the controller and update the document list 6 gt Cal time Motherboard supports processing files towards hours worked Select the file to calculate the work hours worked and click the button Calculation to be completed the control panel will be prompted to complete the calculation And then point to read button shown in the list calculated from the working hours In addition when the document processing operation performed the hours information will also be covered by the actual processing work 7 gt Upload Upload the selected file which is on the motherboard to PC 3 5 Manual Export General Machine Document Manual Info Config Current Position Axis More OfFfset mm Move From origin Speedimm s Power 1 oo IF Light Axis control can only control one axis each time You can set the information for axis move including move length speed laser on off and laser power If you check Move from origin then the offset you set means the offset to machine zero
28. ergy of the layer Enable laser When the machine is equipped with two lasers under normal circumstances is two simultaneous output However users can also be enabled by setting the laser to make them all the way is not output 4 4 2 Laser Scan Parameters Setting Layer Parameter A Layer Parameter i Load parameters From library a Load parameters From library ver ver Is Output Is Output kes E 3 Speedimmisi 100 Default Speedimmisy 100 Default IF Blowing Yes ka IF Blowing ves t Processing Mode Scan wt Processing Mode Scan wt Min Power Max Powers Min Power Max Power o laseri Defaut laser D pefaut C Negative Engrave F Optimized Scan Independent output C Output direct Independent output C FRamp Effect Ramp Length mm Ramp Length mm Qverstriking Un process Overstriking Scan Mode _swing w Scan Mode 4_siwing ka Interval mm 01 Interval mm 0 1 The left side of the dialog box to set the parameters for the vector scan the right of the dialog box a bitmap scan parameters Scan of the vector data do not support Negative Engrave Optimized Scan Output direct Negative engrave If you do not select Negative engraving the black dots which run across the bitmap will emit laser and the white dots which run across the bitmap will not If you select Negative engraving the white dots which run across the bitmap will emit laser and the black dots whi
29. he actual graphic is round and the red rectangle outside the circle is the smallest rectangle click button Go Scale laser head will run x NY For Example Cut Scale As the following figure shown the actual graphic is round and the once along the rectangular path red rectangle outside the circle is the smallest rectangle click button Cut Scale laser head will be cut along the rectangle 4 3 Start Pause Stop SaveToUFile UFileOutput Download Start Output the current graphic to the machine for processing Pause Continue Click Pause will stop the processing work click the button again to Continue Stop Stop the current processing work SaveToUFile Save current file as RD format using for offline processing Can be copied to other memory board for full offline operation UFileOutput Output the offline file RD format After save offline file click UfileOutput to select rd file to processing Download Download the file to the memory of the controller then user can start the file through the machine panel 4 4 Layer Settings Speed MinPower MaxPower Output 100 0 30 0 30 0 Yes 100 0 30 0 30 0 Yes 100 0 30 0 30 0 Yes 100 0 30 0 30 0 Yes Double click the layer that you want to edit in the layer list layer parameters dialog box will pop up Layer parameters in two parts part of the common layer parameters namely how both types of processing layers the layer parameter are valid The other part is t
30. he proprietary layer parameters Namely when change the layer type of processing the corresponding parameters will change Layer Parameter ai Load parameters From library yer Ts Output AEE w Speedimmis Default IF Blowing Yes we Processing Mode Min Powerl Max Power Seal 0 000 Open Delay ms Close Delay ms Through mode 4 4 1 Common Layer Parameters Setting Layer Is Output Speedi mmis Default IF Blowing Yes Processing Mode cyt Min Powerl Maxs Power Laser1 30 Default Laserz 30 a0 Layer Software use layer to distinguish processing graphics parameters of different layers The scan processing methods a number of the bitmap in the same layer the overall output as a picture if you want to separate out all the bitmap the bitmap can be placed into different layers Is Output There are two options Yes and No Select Yes the corresponding layer will be exported for processing Select No the corresponding layer will be not exported for processing Speed The speed of laser processing In terms of cutting speed the better the processing effect is and the smoother the track is the faster the speed is the worse the processing effect is On the scanning process the more slowly the same energy the deeper the next scan scan traces thickening scanning resolution accordingly reduced Faster to scan the same energy the more shallow depth deta
31. il distortion increases On the dot process the main change is the speed of moving air If you check the default the actual speed of the speed set by the panel to decide Is blowing If the machine add a fan and fan has been enabled then if the selection is Yes then when processing the layer it will open the fan otherwise will not open fan If the fan is not enabled you either select yes or No are meaningless Processing mode Processing mode meaning the mode to process corresponding layer If you select vector layer color layer currently there are three options Laser scanning Laser cutting and Laser dotting If you select bitmap layer BMP layer currently there is only one option Laser scanning Laser1 Laser2 Laser signal corresponding to the board 1 channel and 2 way laser output If a single head machine the first 2 way laser meaningless Min power Max power The range of power value is 0 100 it means the intensity of laser during the process the higher the value is the stronger the laser is and the lower the value is the weaker the laser is Processing for different types have different meaning The cutting process the actual power is compared with the cutting speed to follow the speed of low energy is also low high speed energy is high so as to ensure the energy evenly throughout the cutting process Therefore the speed of minimum power corresponding to the lowest energy the minimum speed is
32. ine has been installed lift platform and requires a high degree on different platforms for processing you can the function of Pen up and down This position corresponds to pen up is the height at which the platform for processing carrying the pen position is empty take the corresponding before the platform should be moved to the laser head height which then pan will not produce interference with the workpiece to be processed If the pan does not confirm the laser head to produce interference with the workpiece to be processed you can not lift the pen position set Method 1 gt Enable pen up and down 2 gt The position of pen down Manual control panel key mobile platform to be graphic processing Graphics processing plane adjusting the focus Then the button read you can set the position of pen down 3 gt The position of pen up Manual control panel key mobile platform move to the laser head does not interfere with the workpiece height and moving the laser head through the panel button to confirm no interference click the button read you can set the position of pen up Dot Dot here is specifically for the point drawing tools to draw primitives or imported from a dxf file point primitives And independent of the current way of processing layers namely whether the current layer is cut or a scan pixel graphics of the dot to dot mode is always output The speed of dot is the speed of layer and the energy of dot is the maximum en
33. ircle to determine the speed If parameter configuration appropriate will greatly enhance the quality of small round Click button Add Delete Modify to configuration Small circle is less than speed of the rules limiting the list of small round circle of minimum radius minimum radius circle at the speed of the output of the corresponding If the speed greater than maximum speed limit list the speed round the speed only associated with the speed of the layer If the speed is in the list set the output speed by list If the request received by limiting layer parameters faster than the speed set in the layer press the speed of the output layer 3 2 2 Scan backlash Laser scanning graphic way because the relationship between the machine belt tension may cause the edge of the scanned graphics uneven Therefore increasing backlash to fix It has the specific backlash for the certain speed General the greater the speed the greater the backlash 1 Add backlash Click the Add button the screen will pop up as shown in Figure Speedimrny s Reverse interval ram Set speed and backlash click OK the value to be inserted into the list of backlash 2 Modify backlash Double click the left mouse button scanning reverse gap need to modify the reverse block entry clearance then the pop up screen shown in Figure Reverse intervalimm In the interface can modify the current speed of the corresponding backlash 8
34. kpiece is not very different before use When the relatively large difference in size of the workpiece it is recommended to use directly modify the motor step approach to implementation Rotary engraving is only when using the rotation axis to replace the Y axis use 3 1 4 Feed Setting To use the feed must first enable the feed After set feeding parameters the shaft will be feeding a feeding length and repeat the process until the times of processing reach to number of feeding If the machine is not equipped with feeding devices in general enable the feed ban 3 1 5 Position Setting the laser head back location after processing completed Current position Original anchor Machine Zero Current Position Laser head back to the position before processing Original anchor Laser head back to the last anchor the anchor may set at panel Machine zero Laser head back to the zero of the machine 3 1 6 Output select graphics After check Output select graphics then only output the selected part rather than not output the part not selected 3 2 General settings Export General Machine Document Manual Info Config Small circle speed lirit Scanningi Reverse interval Diametertram Speedirnmy s Speedimmis Reverse int 3 2 1 Small Circle Speed Limit On processing work the software automatically determine whether the current round need to limit speed then according to the diameter size of the c
35. lected graphic 3 gt Change the cutting point Click Cut property gt Set Cut Point to enter the edit mode of the cutting point Then select the curve that should be edited you can double click on the node that you want to set the cutting point to complete the change of the cutting point 2 12 2 Setting And Editing The Cut In Cut Out Lines Drawing or importing curves the curve is default not have any cut in cut out lines If want to add cut in cut out lines select the objects then click Cut property gt Edit cut in property The following dialog box is appear Cut in and out setting Ed ut in Line type Lengthimrn Angle degrees uk out Enable Line Type Lengthitrarn 4nglefdegree To make cut in cut out lines first of all need to enable the cut in cut out function There are two types of the cut in cut out lines straight line and arc Straight line cut in achieve through three ways a Cut in with angle cut in line and starting segment into a certain angle counterclockwise angle is positive b Cutinatcenter the starting point of the cut in line is at center c Cut in from center the direction of the cut in line is from center to starting point and length is as setting Cut out line The arc length of cut in arc is as setting There are two types of cut in cut out arc as shown in the following figure Female Male The processing of setting cut out lines is s
36. ome 3 gt Click toolbar button LazerCut then RDCAM running 1 3 4 Run Illustrator CS5 1 gt Run Illustrator CS5 2 gt Import grahic to Illustrator or draw some 3 gt Click toolbar button then RDCAM running Chapter 2 Software Basic Operation 2 1 Main interface After RDCAM running will see the following interface Familiar to this interface will helpful to use the software for laser working RDCANG 0 01 x 600 000 mm Sy 51 782 mm oo r s S H MinPower MaxPower Gutput 30 0 30 0 Yes 30 0 30 0 a Oo E E w 5 m 7 E E Export General Machine Document Manual Info Config m Fath optimize Oper at ng area 5 E Original or edit path Enable rotate engrave C Order of layer l Inside to outside Diarneter rin a Auto determine start point and dir l S C l Auto find start point Tle pulse joo oo a x Backlash reapy optimize ntr n Block handle Co tro pa e Height so Dir Leto il ae Linefcolumn setup Feeding Count P x Mum ho space mnmi Diskancetmm sco Y Mum ho spacetmmi b Position Seuss USB 4uto SaveToUFile Bestrewing breadth Bestrewing breadth ee Hi See Start About C Output select graphics Download UFileQutput Layer para Depending on the graphics processing requirements layer configuration process parameters Plot area Display graphic
37. ove The Overlap Click menu Tool gt Delete overlap the dialog box appear Delete overlap lines x Enable Overlap error Overlap errorfmm Cancel Under normal circumstances do not select the Enable Overlap error Removing the overlapping lines when two lines are compared to a good degree of coincidence If you need to delete overlapping lines you should select Enable Overlap error and set overlap error Generally do not overlap error set too large so as to avoid accidental deletion 2 12 6 Combine Curve Click menu Tool Combine Curve the following dialog box appears setting combine error ES Combine errorimm k The software automatically merge curves in the selected curves when these curves merge tolerance is less than the setting of combine error 2 12 7 Bitmap Handle Select a bitmap then click menu Tool gt Bitmap handle Bitmap handle width Pixels Height Pixels H Resolution 36 Pixelssinch Y Resolution 96 Pixelsjinch Brightness 0 0 Contrast 0 0 J C Invert color C Set output resolution Resolution pixelsfinch Dither Net graphic aS ESO RES ETE hates Fu Aaa fi esjinc Li Dot graphic Black And White Gray scale Sharpen Apply to view Apply to source In the top right of the dialog box displays the information of the current image Be noted that the horizontal resolution and vertical resolution is
38. s to be processed and simple graphics rendering Graphics Bar Graphics property bar is the basic attributes of graphics operations including graphic location size scale number processing Layer Toolbar Change the color of the selected objects Control Panel All operation relate to processing Operating area basic operation 2 2 Language settings and manufactures information In addition to installation process can set the software language type you can easily switch in different language Export General Machine Document Manual Info Config Import Setting PLT Precision ye Smooth curves Smooth precisiant o Auto close curves Close errortmm 0 1 Combine lines Combine errortrnri 0 1 Auto gray scale Import DxF text info Export Setting Export Precision Velocity Unit we es language English Select the desired type of language can easily switch between different languages To obtain manufacturers information so that we can provide you with better service Click Menu Bar Help gt About cop Mams o O O ets O px O O aan O we O O RECAM 0 0 How to set manufacturers refer to RDCAM Software Setup Manual The bottom of the dialog box shows the current software version number As different versions of software may be have some differences on the functions and interfaces you can easily contact and communicate with manufacturers through software version
39. urrent status of the operation is to edit or view Then you can marquee or click the graphics in the graphics display area or click one pixel or another list to be processed as the first primitive Primitives followed by repeated operations to check many pixels After selecting the graphic select these graphics to be redirected to complete sequencing of all graphics 3 gt Change the direction of graphic processing Mouse select the graphic in the graphics display area or in the list And then click Reverse 4 gt Change the cutting point Set cutting property x No Name ia Name Element Elementz Elementa Element4 Elements Element Element Elements Element Elementid Element11 Elermentiz Elementi3 Element14 Element15 Element16 Elementi Elementi Elementi Elementz0 Elementz1 Element22 Element23 Element24 Elementz5 Elementz6 Element Element2d Element29 Elemento iT i Oo J Oh AN E oo Po e ShowPath xY Select the graphics that should be changed the cutting point it will show all the nodes in the current graphics Select the starting point double click the mouse it will change the starting point of the current graphics After the completion of all changes click ae the result of the changes can be saved In addition to cutting property features the software also offers some tools to change the cutting order cutting direction and cutting point Click menu View Show P
40. usually 0 but if you set a minimum speed of take off speed of the take off speed maximum power corresponds to the layer speed How to set proper Min power and Max power If the laser is too strong during the whole process you should set the minimum and maximal power lower otherwise set them higher If the laser is too weak in some places during the process you should set the maximal power higher If the laser is too strong in some places during the process you should set the minimum power lower If it is cut through the minimum power and maximum power was no significant difference can be set to the same On the scanning process general scanning minimum power and maximum power must be consistent Carving slope the minimum power corresponds to the top of the slope of the power maximum power corresponds to its base of power Minimum power is top of the partial width is too small the details at the Resolution unclear Minimum power is too large then the slope is not obvious Top Bottom On the laser dot process the minimum power and maximum power can be set to the same If you check the default the actual power to set the power from the panel to determine Click the button Advanced you can also set other layer parameters Other layer parameters Ed _ Enable pen up and down Jam o mm Speedinmnmnis Point Enable Laser Enable Laser C Dot intervals eoo cancel Pen Up and Down If the mach
41. ze rectangle Press the Ctrl key while dragging the mouse to draw square Ellipse Click menu Ellipse Drag the mouse on the screen you can draw an arbitrary size ellipse Press the Ctrl key while dragging the mouse to draw round Point Click menu Ellipse Click the mouse on the screen you can draw an point 2 12 Important Tool Here are some frequently used tools Using these important tools can make the current document in the graphics more orderly and make the processing of output more fast 2 12 1 Manual sorting and the set of cutting point and the cutting direction Software provides users a convenient tool for the manual sorting Select Edit gt Set cutting property Cutting property dialog box will pop up All with manual sorting and cut points cutting the direction of the settings in this dialog box can be completed Set cutting property Mame Elementi Elementz Element Element4 Elements Element Element Element Element Elementid Element11 Elermentiz Elementi 3 Element14 Element15 Element1 Elementi Elementi Elementi Elementz0 Elementz1 Element22 Element23 Element24 Elementz5 Elementz6 Element Element2d Element29 Element30 LUT ae o m gl X K Ea 1 gt Show path First check the show path it will display the current graphics cutting order and the cutting direction 2 gt Manual sort Select NI This button is used to switch the c
Download Pdf Manuals
Related Search