Standard Nagel M2 Bookletmaker Operators Manual
Contents
1. on the driver blade must show towards the rear side of the machine BOOKLETMAKING OR FOLDING Adjust guides 10 11 14 to paper format Switch selector 8 to the icon for BOOKLET Insert paper making sure the sheets are squared up correctly Push button START 6 The stacker 4 can be used to stack a couple of booklets If you only want to fold without stapling then just remove the staples from the stapling heads 5 SIDE OR CORNER STAPLING Note There is a maximum of two stapling heads in this mode Switch selector 8 to the icon for CORNER STAPLING A click sound indicates the activation of the corner stapling back stop which is responsible for stapling 4mm away from the paper edge Now the paper can only be inserted 5cm 2 deep into the bookletmaker FOLDNAK M2 Disengage the folding knife to prevent the stapled paper from being folded To do turn so that it stays pulled out Insert paper making sure the sheets are squared up correctly Push button START 6 Proceed in reverse order for making booklets again You must distinctly feel that the knob 3 on the machine s left side is pushed in 6 TROUBLESHOOTING Machine is switched on but the light inside the ON OFF selector 7 is not on The power cord is plugged in improperly Push power cord thoroughly into power outlet Circuit breaker has been Push circuit breaker button in again It is located at the machine s rear benea2. Use original NAGEL Staples Incorrect staple type Use original NAGEL Staples types 26 6 Ri 26 6 or 26 8S See chapter 2 Driver blade 16 has been put in the wrong Put in the driver blade with the mark 26 way showing towards the rear side of the Residues inside staple channel Take off stapling head remove both screws of front plate 18 take off front plate Clean staple channel and reassemble the stapling head Button START 6 is being pushed without paper inside the machine and fire only with paper being inserted Staples give a weak bind because staple Use staples 26 8S with 8mm leg length for Paper cannot be inserted properly Selector 8 is in position for CORNER You can only insert paper for 5cm 2 when side or comer stapling This is normal Set selector 8 into position BOOKLET if you wish to produce booklets Paper is not being folded and ejected Knob 3 at the machine s left side is Pull the knob turn it by 90 push it pulled out disengaging the folding knife towards the machine Internal problem Booklet is stapled correctly but incorrectly ejected Reduce stickiness of fold rollers because of Clean fold rollers dirt Too many sheets have been inserted Do not insert more than 15 sheets See chapter 9 Booklets are being stapled or folded incorrectly The side guides 10 11 or the back stop 14 are fixed improperly and move and back stop properly
3. immediately and call your dealer 9 TECHNICAL DATA Input paper sizes for booklets Paper sizes for side or corner stapling Maximum booklet size Maximum size of stapled blocks Stapling heads Staple magazine Staples Loop Staples Cycle speed Power requirements Weight shipping weight Dimensions height x width x length Shipping dimensions height x width x length Accessories DIN AS 5 Yx 8 Y A3 11 x 17 SRA3 DIN AS 5 Y x 8 Y A4 8 Yx 11 60 pages or 15 sheets 80g paper 30 sheets 80g paper 2 upgradeable to 4 USA max 3 210 staples stapling head NAGEL 26 6 6mm leg length NAGEL Ri 26 6 6mm leg length loop NAGEL 26 8S 8mm leg length steel User dependant up to 500 booklets hr 230V AC 50Hz 100W 110V AC 60Hz 100W 39 kg 86 lbs 41 5 kg 91 5 Ibs 11 x 19 1 3 x 20 16 1 3 x 26 2 3 x 24 Stand on casters Additional stapling heads Original NAGEL Staples
4. abcofficee When You Need More Than Staples Toll Free 800 658 8788 Fax 801 927 3037 Standard Nagel M2 Bookletmaker Operators Manual Read this manual and thoroughly familiarize yourself with its contents before operating or servicing the equipment STANDARD TABLE OF CONTENTS id D P OY H Setup Loading of Staple Magazine Adjustments 3 1 Paper Width 3 2 Paper Length 3 3 Position of Stapling Heads Bookletmaking or Folding Side or Corner Stapling Troubleshooting Maintenance Security Technical Data Congratulations for choosing to purchase the BOOKLETMAKER FOLDNAK M2 It makes fast and easy work of producing impressive looking booklets Even small quantities become efficient to produce because adjustment requirements are minimal Your bookletmaker is also a side or corner stapler or a folding machine COMPONENTS DELIVERED Bookletmaker FOLDNAK M2 with two stapling heads bag with two knurled screws 1 5 000 NAGEL Staples 26 6 instructions manual 1 SETUP Screw in the two knurled screws 1 Plug in the power cord 2 LOADING OF STAPLE MAGAZINE Pull stapler pusher 12 back until it locks on by itself Open magazine cover 13 Load staples Close magazine cover 13 Push staple pusher 12 gently down to unlock it and guide it towards the machine s front side Do not let the staple pusher snap forward because this would smash the stick of staples You can use either of t
5. around The side guides 10 11 are too far apart from each other allowing unparallel See chapter 3 1 insertion of paper The side guides 10 11 are adjusted to ai side guides farther apart See chapter tightly causing larger paper formats to curl during folding which leads to incorrect stapling Incorrect adjustment of backstop 14 Adjust backstop more precisely so that the machine folds in the center of the sheets Paper is not squared up correctly Square up paper correctly before firing 7 MAINTENANCE Replace scratched or bent driver blades 16 Clean the machine only with a soft and moist tissue without chemical substrates Clean the folding rollers using a substrate that does not dissolve rubber 8 SECURITY The machine must only be used for the stapling and folding of paper Connect machine only to an grounded power outlet Switch off after use Make sure that the power requirement indicated at the machine s back side is the same being provided on your premises before connecting the power cord Check function of safety shut off regularly the machine must not run with cover 5 opened Clean and service the machine only with the power cord disconnected Place on an even support and never in a humid surrounding avoid direct sunlight Never put mugs glasses or bottles onto the machine If you notice smoke heat excessive noises or any unusual performance disconnect the power cord
6. he three original NAGEL Staple types 26 6 Ri 26 6 or 26 8S We recommend that you use the staple types as shown below Staple Type Loop Staple Flat Staple Flat Staple Ri 26 6 Use only NAGEL staples as other staples may damage the stapling head or lead to bad results Booklets 2 15 sheets Thin Paper Sets ca 2 15 sheets Thick Paper Sets ca 16 30 sheets 3 ADJUSTMENTS 3 1 PAPER WIDTH Position the left side guide 10 according to the paper format required using scale 2 and fix it with the knurled screw 1 Insert paper squaring it up parallel to the left guide 10 Shift the right side guide 11 closely to the inserted paper and fix it leaving 0 5mm of air Important The side guides 10 11 must not catch on the movement of the sheets 3 2 PAPER LENGTH Open cover 5 Adjust and fix the back stop 14 according to your paper format using the scale Close cover 5 Check the adjustments 3 1 and 3 2 with a test run and readjust if necessary 3 3 POSITION OF STAPLING HEADS The bookletmaker FOLDNAK M2 is able to use four stapling positions with up to four stapling heads USA Five stapling positions with three stapling heads DIN distances between the stapling heads are 50mm x 80mm x 50mm USA 2 1 8 on center Unlock the latch 15 Take out stapling head put it into a new position and lock the latch 15 The driver blade s 16 hole needs to be hinged onto the pin 17 and the mark 26
7. th the power cord outlet Button START 6 is being pushed but machine does not work Staple jam inside staple channel Take off stapling head remove both screws of front plate 18 take off front plate Remove jammed staple clean staple channel and reassemble Jam of the moving parts because too much Push button RESET 9 for a few paper has been inserted seconds The machine then runs backwards enabling the operator to pull out the jammed paper Circuit breaker has been activated Push circuit breaker button in again It is located at the machine s rear beneath the power cord outlet Machine does not staple although the staple magazine is filled Driver blade 16 is not hinged onto pin Hinge hole of the driver blade 16 onto pin Put in a driver blade The mark 26 must show towards the rear side of the machine Staple jam inside stapler magazine Use original NAGEL Staples and make sure to only use types 26 6 Ri 26 6 or 26 8S Stapler pusher 12 does not push staples Push staple pusher gently down to unlock and guide it towards the staples Staple jam inside staple channel Take off stapling head remove both screws of front plate 18 take off front plate Remove jammed staple clean staple channel and reassemble Use only original NAGEL Staples and make sure to only use types 26 6 Ri 26 6 or 26 8S Frequently miss stapling or two staples in one position Insufficient staple quality
Download Pdf Manuals
Related Search