User's gUide User's gUide
Contents
1. IP69K OPTION USER S GUIDE E USER SECURITY Do respect the power supply voltages and the connection terminals Do not modify or dismantle all or part of the product Do not connect or clean when power is on Do not watch the lighting source directly and follow the advice below If the workstation enables it interpose a filter that will stop the lighting radiation under fixed or adjustable frame between the source and the operator e When these measures cannot be implemented supply the operators with glasses class 4 available for sale at TPL Vision or with a dedicated protective mask that will stop the lighting radiation Forbid or limit the direct access to the lighting source exposure into the radiation axis Establish a security perimeter so as to prevent the operators from approaching the lighting source beyond the recommendations of the manufacturer as for eye irritation is concerned e n any case ensure that the chosen means properly reduce the exposition quantities features of screens or glasses to be chosen according to the wavelengths that the operators are exposed to E EQUIPMENT MAINTENANCE CLEANING when the product is switched off Please use a soft and dry cloth Do not use any abrasive material Do not use any cleaning solvent or aggressive chemical product isopropyl alcohol og TPU 20 rue de Saint Philbert 44118 La Chevroli re France TEL 33 0 2 40 56 10 99 FAX 33 02. Please find below an indicative table recapitulating the classes of risk for our standard products Colour Risk In all cases TPL Vision recommends the use of the protection glasses White WHI Green 525 nm Red 630 nm 0 none that are listed in its catalog Se Mitty BITE Aol Ts 8 310 Ue l low For more information about photo UV 365 nm 2 moderate biological risks do not hesitate to contact us UV 385 nm 3 high IP69K OPTION USER S GUIDE E RECOMMENDATIONS 1 Temperature conditioning before the set up please store the bar during 24 hours in its package at the operating temperature the packa ging will slow down the crossing time from 20 C to 5 C and the air vent will balance both the pressures and the humidity 2 Setting up as soon as the product Is brought out of its packaging please set up immediately connect the fans and turn them on 3 Use e never turn off the fans e unless it is used in continuous mode do not put the bar in a place where the temperature may vary rapidly close to the door of a refrigerator at 20 C e do not wash the product with warm water max 80 C more than 1 minute to avoid any condensation phenomenon e if the product is working in continuous mode do not turn it off during the cleaning e if the product is working in strobe mode please respect the following steps during the cleaning with warm water switch the bar on in continuous mod
3. 2 40 56 42 89 VISION ae is tv e S Active LED solutions www tpl vision com edition 5 L liable to changes without notice and presentations ures 62 TPL IP69K OPTION aaa VISION USER S GUIDE a gt Active LED solutions PREAMBLE This notice includes all the advice and warnings that enables a correct set up and a safe use of the product TPL Vision can not be responsible for the bad use of the notice If so TPL Vision cancels the guarantee s effects neon E UNPACKING Products are packed in our factory using suitable materials for a safe transport through the usual means of transpor tation in France and abroad However a damaged package must be reported to the carrier on delivery Hand written reservations must be indicated on the delivery order Moreover please send a letter or an email to TPL Vision as soon as possible up to 24 hours after the delivery If the transportation damage has not been stipulated on the delivery order and reported to TPL Vision in time the package will not be taken back nor exchanged To open the package do not use any cutting blade so as to avoid damages on the product Please use the delivered accessories if needed do not use any other products or equivalents to replace the delivered accessories E RISK CLASS The EN 62471 norm about lighting fluxes enables the classification of led lightings in 4 distinct groups according to their hazardousness degree
4. e at least one color for RGB bars during 30 minutes clean the product while it is turned on turn it off but keep the fans on during 1 hour you can now use the bar in strobe mode again EE FIXING 64 7 mm PLEASE MOUNT THE STRUCTURE ON A FLAT SURFACE 4 M8 ATTACHMENT POINTS BAR LENGTH 106mm BAR LENGTH 131mm BAR LENGTH 153mm E OTHER FIXING POSSIBILITIES Beware if you don t want to use the brackets supplied with the product on a flat surface here are our recommendations 1 You can use clamps Please place them on the o ring of the tube Do not press it to avoid any pressure or fissure LOCKING ON JOINT 2 You can also mount the tube with your own brackets Then you have to insert rubber blocks to avoid any pressure on the tube RUBBER BLOCK In all cases if the mounting recommendations are not followed TPL Vision can decide to cancel the warranty in case of damage ma CONNECTION To connect the lighting please refer to the associated user s guide To prevent any steam appearance inside the product you need to power the ventilation system The fan has to work 24 hours a day Ventilation connection Brown wire 24V Blue wire GND
Download Pdf Manuals
Related Search