User's gUide
Contents
1. id y TPL MFDOME STANDARD amp OVERDRIVE oo VISION USER S GUIDE Active LED solutions PREAMBLE This notice includes all the advice and warnings that enables a correct set up and a safe use of the product TPL Vision can not be responsible for the bad use of the notice If so TPL Vision cancels the guarantee s effects ekee E UNPACKING Products are packed in our factory using suitable materials for a safe transport through the usual means of transportation in France and abroad However a damaged package must be reported to the carrier on delivery Hand written reservations must be indicated on the delivery order Moreover please send a letter or an email to TPL Vision as soon as possible up to 24 hours after the delivery If the transportation damage has not been sti pulated on the delivery order and reported to TPL Vision in time the package will not be taken back nor exchanged To open the package do not use any cutting blade so as to avoid damages on the product Please use the delivered accessories if needed do not use any other products or equivalents to replace the delivered accessories E RISK CLASS The EN 62471 norm about lighting fluxes enables the classification of led lightings in 4 distinct groups according to their hazardousness degree Please find below an indicative table recapitulating the classes of risk for our standard products Colour Class Risk In all cases TPL Vision recom2. mends the use of the protection glasses White WHI Green 525 nm Red 630 nm 0 none that are listed in its catalog DNA a Te Get ate l low For more information about photo UV 365 nm 2 moderate biological risks do not hesitate to contact us UV 385 nm 3 high TPL Vision can provide calculation notes about the nominal distance of eye risks security distance BEWARE to the infrared light invisible to the eyes To know if the light is on please refer to the LED indicators MEDIUM FLAT MFDOME STANDARD amp OVERDRIVE USER S GUIDE M DIMENSIONS Height with Diameter pay pe se fixing plate of central mm mm hole mm A B C C 10 mm D Min 200 Max 1900 Min 200 Max 900 45 55 65 e Useful surface x B Max useful surface 0 88 m2 e Max useful perimeter 4 5 m Total surface connector excluded A 4mm x B 4mm E FIXING ON THE MACHINE During the set up the light has to be switched off and unplugged Please use the fixing groove or holes designed for that purpose We recommend the using of nuts supplied in the groove or M4 screws not supplied with a tightening torque from 0 5 to 1 5 Nm We also recommend the use of a threadlocker not supplied to avoid any risk of loosening FIXING ON THE LENGTH groove FIXING ON THE CORNER max depth 5mm 4 M4 nuts supplied CHC screw M3x20 not supplied 10 BEWARE to the use of angle brackets x Do n
3. nd dry cloth Do not use any abrasive material Do not use any cleaning solvent or aggressive chemical product isopropyl alcohol 06 7 ds 3 TPL 0 VISION Active LED solutions 20 rue de Saint Philbert 44118 La Chevroli re France TEL 33 0 2 40 56 10 99 FAX 33 0 2 40 56 42 89 www tpl vision com Version B 2 2015 07 edition Features and presentations liable to changes without notice
4. ot hang up f f x Do not deform the structure NA t M CAMERA FIXING Length 125 mm 125 62 5 Width 125 mm 8 Height 10 mm 125 Screw M6 MEDIUM FLAT MFDOME STANDARD amp OVERDRIVE USER S GUIDE M LED INDICATORS amp POTENTIOMETER LED indicator strobe mode ee _Singleturn ee a ea ie __________ potentiometer 20 100 LED indicator functioning mode EE WIRING STANDARD VERSION OVERDRIVE VERSION SURFACE lt 0 5M SURFACE gt 0 5N SURFACE lt 0 25N 0 25M lt SURFACE lt 0 88N 1 wiring 1 wiring 1 wiring 2 wirings ee ee ee o o 0 M12 connector M12 connector M12 connector Cable Cable Cable Cable M POTENTIOMETER SETTING STANDARD VERSION e Lowest level of the potentiometer 20 of the power e Highest level of the potentiometer 100 of the power 350mA led OVERDRIVE VERSION nuous mode To use it in Overdrive lighting power x3 when the potentiometer is set at 100 you must When the product is delivered the potentiometer is set at 30 and the product can be used in conti A absolutely respect a maximum lighting time of 3ms and a maximum duty cycle of 10 EM CONNECTION M12 Connector POWER CONNECTOR T CODING black ami brown ANS blue 24V EE Ce 3m GND wie STROBE L NPN STROBE mode PNP from 5 to 24V for 100 ON From O to 1V fo
5. r 100 OFF NPN less than 1V for 100 ON Above 2V for 100 OFF Max 20V Voltage drop for Connector M12 wire 10 meters Minimum Voltage at the product input 20VDC 1 15V 5A Cable 2 white STROBE NPN brown 24V Tp gt black STROBE PNP STROBE mode PNP from 5 to 24V for 100 ON From 0 to 1V for 100 OFF NPN less than 1V for 100 ON Above 2V for 100 OFF Max 20V Voltage drop for Cable 10 meters Minimum Voltage at the product input 20VDC 1 15V 5A STROBE PNP STROBE NPN i 24V 1 24V _ 2 2 NPN 3 Ground J 3 Ground JS 4 PP EE 4 CONTINUOUS MODE 1 24V J 1 24 l2 3 Ground 4 PNP 2 NPN Ground 2 3V 10A 3 5V 15A 4 6V 20A MAX 20A STROBE PNP STROBE NPN E 24V Gi 24V 2 2 NPN H 3 Ground JW 3 Ground E 4 PNP En 4 CONTINUOUS MODE 1 24V E 24V D 2 NPN F Ground 3 Ground 4 PNP 2 3V 10A 3 5V 15A 4 6V 20A MAX 20A MEDIUM FLAT MFDOME STANDARD amp OVERDRIVE USER S GUIDE P6 8 Overdrive version WIRING 2 Control and power Power In the OVERDRIVE version both wirings can be powered by THE SAME POWER SUPPLY 24V M TECHNICAL INFORMATION FEATURES MFDOME MFDOME Overdrive 1 32W par 25cm 3W 25cm in peak max Consumption de Tee 0 43W 25cm2 max on average 3ms 10 Min functioning Voltage 20V in the light input Normal functioning Vol
6. tage 24V in the light input 10 Max functioning Voltage 30V in the light input Max consumption Strobe signal 5mA 10 to 40 C 80 of humidity without condensation No thermal shock max temperature variation 10 C in 24h Operating temperature M USER SECURITY Do respect the power supply voltages and the connection terminals Do not modify or dismantle all or part of the product Do not connect or clean when power is on Do not watch the lighting source directly and follow the advice below e f the workstation enables it interpose a filter that will stop the lighting radiation under fixed or adjustable frame between the source and the operator e When these measures cannot be implemented supply the operators with glasses class 4 available for sale at TPL Vision or with a dedicated protective mask that will stop the lighting radiation e Forbid or limit the direct access to the lighting source exposure into the radiation axis e Establish a security perimeter so as to prevent the operators from approaching the lighting source beyond the recommendations of the manufacturer as for eye irritation is concerned e In any case ensure that the chosen means properly reduce the exposition quantities features of screens or glasses to be chosen according to the wavelengths that the operators are exposed to M EQUIPMENT MAINTENANCE CLEANING when the product is switched off Please use a soft a
Download Pdf Manuals
Related Search