OPERATING INSTRUCTIONS
Contents
1. the lower position 2 Position and align the rewinder with the printer 3 Thread the supply as shown Rewinder Printer Note Feed the supply under the pick up arm 4 Tape the supply to the empty core 5 Turn on the rewinder For inside winding 1 Slide the direction switch to the upper position Q 2 Position and align the rewinder with the printer 3 Thread the supply as shown Rewinder Printer Note Feed the supply under the pick up arm 4 Tape the supply to the empty core 5 Turn on the rewinder2. the rewinder ever needs repair Assembling the Rewinder To assemble the rewinder you need a Phillips screwdriver 1 Line up the holes in the base with the holes in the bottom of the rewinder 2 Use the four Phillips screws to attach the base to the rewinder The lower pin prevents the pick up arm from being assembled on the wrong side of the shaft Pe aie Pick up arm Phillips Screw __ h B Base CAUTION Do not lift or carry the rewinder using the pick up arm Monarch and 935 are trademarks of Avery Dennison A AVERY Retail Information Services LLC DENNISON TC09350I1 Rev AF 10 10 2007 Avery Dennison Corp All rights reserved Setting Up the Rewinder The rewinder includes either 3 inch or 4 inch core holders standard The optional Core Kit PN124476 includes 1 inch and 3 inch core holders a spindle and bale for coreless operation Order the Core Kit to match the core sizes you need 1 Slide a disk onto the shaft Make sure the disk rests on the small ridge on the shaft 2 Select the core holder with the small metal clips on the edge 3 Slide and thread the core holder onto the shaft with the beveled edge towards the empty core Note The shaft is threaded and only the core holder with the metal clips threads onto the shaft 4 Slide an empty core onto the shaft Make sure it rests firmly on the core holder 5 Slide the outer disk onto the retainer Make sure the disk rests on the
3. Rewinder Specifications Height 8 5 inches 210 mm 12 inches 305 mm with disks attached Width 10 inches 255 mm Depth 10 inches 255 mm Weight 10 9 Ib 5 kg Hub 3 inches 76 mm Rewinder P N M093503 Diameters 4 inches 102 mm Rewinder P N M093502 1 inches 25 mm optional kit 3 inches 76 mm optional kit Coreless optional kit Rewind 1 to 12 inches per second Speed 25 mm to 305 mm Operating 40 F to 110 F 4 C to 43 C Temperature Storage 15 F to 120 F 9 C to 49 C Temperature Relative Operating and Storage Humidity 5 to 90 non condensing Supply Specifications Supply 0 005 inches to 0 012 inches Thickness 0 13 mm to 0 30 mm Supply 1 2 inches to 4 125 inches Width 30 mm to 105 mm Coreless 1200 inches 30 480 mm Maximum For supplies service or assistance call toll free 1 800 543 6650 In the U S A 1 800 387 4740 In Canada www monarch com OPERATING INSTRUCTIONS These instructions explain how to set up and use the Monarch 935 Rewinder To use multiple core sizes order Rewinder M093502 and optional Core Kit P N 124476 which includes a 1 core a 3 core and a spindle and bale for coreless operation Unpacking the Rewinder After unpacking the rewinder you should have the rewinder power supply with cord the base four Phillips screws two supply guide disks two core holders and a retainer with thumbscrew Keep the box and packaging material in case
4. r 1 inch or 3 inch operation see Setting Up the Rewinder Note The maximum number of inches to rewind with the coreless adapter is 1200 For coreless operation 1 Slide a disk onto the shaft Make sure the disk rests on the small ridge on the shaft 2 Remove the bale from the coreless adapter Slide the threaded end of the coreless adapter onto the shaft 3 Tighten the coreless adapter onto the shaft Place less than 0 5 inch of supply onto the adapter and slide the bale onto the adapter Make sure the short end of the bale is on the top 5 Wind a few labels onto the adapter 6 Turn on the rewinder When finished rewinding remove the bale and slide the roll of rewound supplies off the shaft Connecting the Cables 1 Plug the power supply into the inlet 2 Plug the power cable into the power supply Direction Switch Power Inlet Power Cable 3 Plug the other end of the cable into a grounded electrical outlet 4 Turn on the rewinder Using the Rewinder The rewinder can be set for inside labels wound in or outside labels wound out winding If the full roll of supply was wound face out it should be rewound face out if the full roll of supply was wound face in it should be rewound face in The winding direction switch is located directly above the power inlet Direction Switch g 9 Power re i ZY For outside winding 1 Slide the direction switch to
5. small ridge on the retainer Thread the retainer into the core holder tighten and slide onto the shaft Make sure the beveled edge of the core holder fits into the empty core 6 Align and tighten the thumbscrew with the flat on the shaft to the outer disk Do not push the outer disk in too far Disk Empty Core Retainer Thumbscrew Core Holders Outer Disk Troubleshooting may occur Problem Rewinder feeds supply instead of rewinding Use the following table to correct some minor problems that Action Make sure the direction switch is set properly The core does not stay on the core holder Make sure the inside core holder is the one with the small metal clips on the edge Supply is pinched when rewinding Make sure the outer disk has not been pushed in too far Rewinder is pulling too hard on supply or supply perforations are breaking Note Make sure the supply is fed under the pick up arm and then attached to the empty core or coreless adapter Disable the printer s backfeed option when using the rewinder poor image placement and or supply errors may occur Removing the Supply 1 Loosen the thumbscrew on the outer disk 2 Remove the outer disk and core holder 3 Remove the roll of rewound supplies Setting Up for Coreless Operation The rewinder includes 3 inch or 4 inch core holders standard Set up is the same when using the optional core holders fo
Download Pdf Manuals
Related Search