m-CAN J1850 – Installation and Operating Instructions For Harley
Contents
1. Connecting the motogadget indicator lights to the m CAN Together with the end ferrules insert the cables of the indicator lights into the screw on terminal see table below and tighten the screws motosign mini a HD handlebar clamp Terminal MS cobi frame metric handlebar clamp motoscope tiny motoscope classic Active view white brown white yellow pe connect to terminal No 19 m CAN _ motogadget a a E J1850 Connecting the supplied motogadget HD Sportster type vehicle connector to the m CAN Insert the cable of the model specific connector included with Terminal Connector ee Color code the attached end ferrules into the screw type terminals shown in table on right side and tighten the screws ATTENTION Remove the grey connector insert inside the connector attached to the vehicle Now please make sure to note the proper polarity when o xg brown plugging the motogadget connector into the connector attached to the vehicle The connector is equipped with a large and a small tab on the left side and the right side respectively Please make sure they fit into the corresponding seat Connecting the menu push button The menu push button is connected to the terminals No 17 and 18 The polarity is irrelevant Mounting the cables to the m CAN Screw the provided black mounting plate to the two mounting bolts on the m CAN To ensure optimum strain relief combine all connecting cables2. see right hand figure and mount them to the mounting plate using both tie bands The m CAN is mounted to vehicle parts or the vehicle wiring harness by screws or tie bands respectively with both bores of the mounting plate Notes No additional mounting of cables required Short circuits of terminal block outputs or contact to ground or 12V respectively may damage the device If the original fuel display remains connected it is not possible to operate the low fuel indicator Therefore you have to disconnect the fuel display from the wiring harness an alternative is not to connect the cable to terminal No 11 Instrument settings motoscope mini Classic Chronoclassic Pro and SureShift ImpE 1 ImpW 4 und Circ 2000mm motoscope Tiny Pulse 4 Circ 2000mm Modes Some of the indicator lights are multi functional For example the figure below shows the modes of the indicator lights assembly with 5 lights ms combi frame motosign mini Activeview and handlebar clamps When using the motoscope Tiny and motoscope Classic only 4 indicator lights are available The display mode layout is as follows green LED left turn signal flashing and low fuel indicator continuously blue LED high beam green LED neutral red LED right error memory flashing and oil pressure continuously OAF FAO turn high beam neutral oil pressure fuel left right MIL flashing alarm flashing The motogadget team
3. wishes you a pleasant and safe trip and a lot of fun with your new motogadget instrument
4. m CAN _ motogadget a a E J1850 m CAN J1850 Installation and Operating Instructions For Harley Davidson XL Sportster model series Thank you very much for choosing a high quality product of motogadget The m CAN and connected instruments might be damaged when installed improperly Please read the following information carefully and follow instructions during installation Please note the correct order of the steps performed in these installation and operating instructions THE CASING MUST NOT BE OPENED IN CASE OF NON COMPLIANCE ALL WARRANTY CLAIMS WILL BECOME VOID THE ONLY INTENDED USE OF THIS DEVICE IS THE COMBINATION WITH MOTOGADGET INSTRUMENTS IN CASE OF IMPROPER USE WITH THIRD PARTY INSTRUMENTS ALL WARRANTY CLAIMS WILL BECOME VOID IN CASE OF NON INTENDED USE THE DEVICE MAY BE DAMAGED IN CASE OF MALFUNCTIONS THE M CAN HAS TO BE RETURNED TO MOTOGADGET FOR INSPECTION TOGETHER WITH THE USED MOTOGADGET INSTRUMENT MOTOGADGET WILL ACCEPT NO LIABILITY FOR ANY DIRECT INDIRECT OR SUBSEQUENT DAMAGE OF ANY KIND RESULTING FROM USE INSTALLATION OR CONNECTION OF THE DEVICE OR OTHER DELIVERED EQUIPMENT THIS EXCLUSION OF LIABILITY APPLIES TO INCLUDING BUT NOT LIMITED TO PERSONAL MATERIAL AND FINANCIAL DAMAGES PARTICULARLY THE USE IN PUBLIC TRAFFIC IS AT THE USER S OWN RISK Scope of Application Using the m CAN all motogadget instruments except motoscope Pro can be connected directly to the wiring harness of the Harley Davids
5. on Sportster series models built from 2004 to 2011 There is no need for modifications to the original motorbike wiring harness Instrument installation According to the respective manual remove the tank and the original soeedometer Disconnect the connector of the speedometer connecting cable from the vehicle s wiring harness Subsequently the m CAN connector will be connected with the connector on the vehicle In case this connector has a grey housing it is a DEUTSCH connector a black housing indicates a MOLEX connector Mount the motogadget instrument and if available the motogadget indicator lights assembly to the vehicle Please use the extensive mounting hardware kits provided for Harley Davidson vehicles Now route the instrument cable and the indicator lights assembly cable to the position of the wiring harness connector of the original soeedometer Carefully remove 50 mm 2 in of the cable jacket Next remove 10 mm approx 1 2 in of the strand insulation and slide the end ferrules onto the exposed strand ends Cut off any excess cable material using wire cutting pliers Connecting the motogadget instrument to the m CAN To protect the components make sure to apply contact grease to all metal parts of the screw type terminals Insert the instrument cables into the corresponding terminals see table below and tighten the screws Terminal motoscope mini motoscope classic motoscope tiny SureShift Multiview 25 red
Download Pdf Manuals
Related Search