Home

Operating Instructions (English)

1. 27 Replacing Consumables 0000 cece eee 29 e Replacing the paper feed roller module 2 0 00 eee eee 29 e Replacing the double feed prevention roller module 32 How to re attach the sensor rollers 34 e Re attach the sensor roller for back scanning to the ADF door 34 e Re attach the sensor roller for front scanning 000 eee eee 34 Shading Adjustment 0 0 02 es 35 Repacking Instructions 0000 cee es 36 e KV S2048C KV S2028C KV S2026C S2026CU S2026CA 36 e KV S2046C S2046CU S2046CA 1 0 aaa 37 SPCCHICANONS saueren te NG NANA PANAMA NGA 38 e Changing the paper feed roller module and double feed prevention roller 39 Troubleshooting 4 40 Notice Federal Communications Commission Reguirements For United States only Note This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmf
2. 10 Component Identification E Power turn on sequence 1 Turn on the power of the scanner e Press the power switch The LED will now light 2 Turn on the power of the host computer after scanners LED lights green e In case of the USB connection the host computer recognizes the scanner auto matically when the scanner is powered on even after the host computer is powered on E About LED LED indicates the status of the scanner as follows LED light Ready to scan or scanning Green Blink Sleep mode Orange Blink Initializing Sleeping with warning Ko x1 x1 x2 The rollers need to be cleaned or replaced Check the status of the scanner using the User utility The User utility is included in the CD ROM ss With KV S2048C and KV 52028C the LED blinks in green 11 Component Identification E About the SCSI setting for using SCSI interface only For KV S2046C S2046CU S2046CA S2026C S2026CU S2026CA When connecting the scanner to a SCSI chain using a SCSI cable perform the SCSI ID setting correctly The scanner is provided with a DIP switch for the SCSI ID No setting and the terminator setting DIP switch SCSI ID TERM ON 210 SCSI ID Setting o fo fo o e The last device in the SCSI chain e Default setting Not the last device in the SCSI chain 12 Installing Software E System requirements KV S2048C KV S2046C S2046CU S2046CA KV S2028C KV
3. 1 2 3 4 Insert the CD ROM into your CD DVD drive on your computer If you have a feature called Autorun activated this will start the installation process automatically Note e If the AutoPlay dialog box is displayed in Windows Vista select CDRun exe e If the program does not automatically start click Start click Run click Browse and select the CD DVD drive containing the installation software double click on CDRun exe in the root directory to manually start the installation routine then click OK Select your scanner Select a manual from the list E Viewing manuals installed on your computer All manuals installed on your computer can be viewed as follows 1 Click Start and then click All Programs Panasonic Scanner Manuals e For Windows 2000 click Program instead of All Programs Note e To install manuals on your computer see page 16 2 Select the desired manual 17 Document Specifications E Acceptable documents Document size Paper thickness 50 8 216 mm 2 0 8 5 in Single paper feeding 40 127 g m 10 7 33 9 Ib Continuous paper feeding 50 127 g m 13 3 33 9 Ib The height of all the documents on the tray should not 70 635 mm 2 76 25 in exceed the limit mark on the document guide Single paper feeding is recommended for papers exceeding the legal size length Feeding direction E Unacceptable documents The following
4. Model No KV S2048C Items 343 x 487 x 269 mm 343 x 487 x 239 mm 343 x 487 x 269 mm 13 5 x 19 2 x 10 6 in 13 5 x 19 2 x 9 4 in 13 5 x 19 2 x 10 6 in Note When tray is Note When tray is Note When tray is pulled pulled installed Weight 9 1 kg 20 1 Ibs 8 6 kg 19 0 lbs 8 5 kg 18 7 lbs Power requirement AC100 120V 50 60 Hz Unit i AC220 240 V 50 60 Hz Maximum 1A AC100 120 V Scanning 0 5A AC220 240V Power aa 03A Standby 0 2A External dimensions Width x Depth x Height AC100 120 V 0 35 A AC100 120 V 0 3 A AC100 120 V AC220 240 V 0 2 A AC220 240 V 0 2 A AC220 240 V 3 5 W AC100 120 V I 6W AC100 120 V 3 5 W AC100 120 V 6 W AC100 120 V Sleep mode consump tion 6 W AC220 240V 8W AC220 240 V 6 W AC220 240 V 8 W AC220 240 V Operating temperature Temperature 15 C to 30 C 59 F to 86 F Environ and humidity Humidity 30 to 80 RH ment Storage temperature Temperature 0 C to 35 C 32 F to 95 F and humidity Humidity 10 to 80 RH CD ROM s Printed documents Safety and Installation guide Power cord Roller cleaning paper USB cable For KV S2048C and KV S2028C only Shading paper For KV S2048C and KV S2028C only Accessories White roller kit KV SS023 Roller Exchange Kit with Black Sensor Roller KV SS024 Roller Exchange Kit with White Sensor Roller KV SS025 Roller cleaning pa
5. e Original Scanner Carton amp Packing Materials e Shipping Tape and Scissors 1 Turn the power switch off and disconnect your scanner from the electrical outlet and the interface cable 2 Remove the feed extension tray and exit extension tray 3 Pack the scanner Power cord e Be sure to use a power cord whose shape matches the shape of the electric outlet CD ROM Note How to remove the feed extension tray 1 Pull up the tray 2 With pressing down the center of the tray 3 pull out the tray Feed extension tray 37 Specifications KV S2046C KV S2026C Model No KV S2048C KV S2046CU KV S2028C KV S2026CU Items KV S2046CA KV S2026CA Scanning method CIS Contact type color mage sensor Front amp Back sides Background Black sensor roller Scanning Binary SimplexApprox 43 pages min SimplexApprox 23 pages min speed 1 200 dpi DuplexApprox 76 images min Duplex Approx 42 images min Letter size Color SimplexApprox 19 pages min SimplexApprox 10 pages min portrait 150 dpi DuplexApprox 34 images min Duplex Approx 18 images min Scanning Binary SimplexApprox 41 pages min SimplexApprox 22 pages min speed 1 200 dpi DuplexApprox 72 images min Duplex Approx 40 images min A4 size Color SimplexApprox 18 pages min SimplexApprox 9 pages min portrait 150 dpi DuplexApprox 32 images min Duplex Approx 16 images min 100 600 dpi 10 dpi step Optical 600 dpi Main and Sub scanning directions
6. S2026C S2026CU S2026CA IBM PC AT or compatible machine with a CD ROM drive Pentium III 1GHz or higher Windows 2000 Windows XP 2 Windows Vista 3 64 bit is not available USB 2 0 USB 2 0 SCSI III Interface Recommended SCSI board Adaptec SCSI 2930U 2940U 29160N 19160 With Windows Vista Adaptec 29160N 19160 256 MB or higher HDD 1 GB or more free space is required T Microsoft Windows 2000 operating system hereafter Windows 2000 2 Microsoft Windows XP operating system hereafter Windows XP 3 Microsoft Windows Vista operating system hereafter Windows Vista e The above system requirements may not satisfy recommendation of all operating system and bundled application softwares E CD ROM Contents Device Driver Drivers TWAIN ISIS i f RTIV Applications QuickScan Pro M Demo User Utility Contents Control Sheet Warranty Information U S A Only Utilities O Installation Guide Operating Instructions PIE Reference Manual RTIV Reference Manual User Utility Reference Manual e RTIV Reliable Throughput Imaging Viewer is a Panasonic original application software and does not require either TWAIN driver nor ISIS driver e PIE is an acronym for Panasonic Image Enhancement Technology e To view manuals Adobe Reader must be installed e f the CD ROM does not automatically start please run CDRun exe on the CD ROM e There are some restrictions for QuickScan Pro
7. of the scanner Follow the instructions of the hardware wizard to complete the installation The installation process is performed automatically in Windows Vista Even if the screen Digital Signature was not found for this driver or has not passed Windows Logo testing appears continue with the installation 16 installing Software E Application installation RTIV and or QuickScan Pro Demo can be installed as follows 1 2 Insert the CD ROM into your CD DVD drive on your computer If you have a feature called Autorun activated this will start the installation process automatically Note e If the AutoPlay dialog box is displayed in Windows Vista select CDRun exe e If the program does not automatically start click Start click Run click Browse and select the CD DVD drive containing the installation software double click on CDRun exe in the root directory to manually start the installation routine then click OK Select your scanner Select the RTIV or the Quick Scan Pro Demo from the Installation list Follow the instructions on the screen The installation process is performed automatically in Windows Vista Even if the screen Digital Signature was not found for this driver or has not passed Windows Logo testing appears continue with the installation E Viewing manuals from the CD ROM All manuals on the CD ROM can be viewed using the Adobe Reader
8. the shaft reach the springs of the holder Wider groove 6 Close the double feed prevention roller cover a N ju y Y n A Close the ADF door e When you close the ADF door close it securely until the door is locked Clear the roller replacing counter with the User Utility e After the rollers have been replaced press the Clear Counter button in the User Utility to clear the After Replace Roller counter to zero e Refer to the User Utility Reference Manual 33 How to re attach the sensor rollers If the sensor rollers are removed re attach them E Re attach the sensor roller for back scanning to the ADF door Attach the shorter sensor roller to the ADF door by placing the non gear side to the ADF door release e Match the groove to the guide e Push the roller and confirm the sensor is locked by the springs on both sides Springs s IT OD Attach the longer roller to the unit by placing the non gear side to the ADF door release e Match the groove to the guide e Attach the side of the ADF door release first and a T attach the other side 2 o i TH i TY i P her LA VED E Confirm both rollers move slightly e Press down on the sensor rollers and rotate them 34 Shading Adjustment For KV 52048C and KV S2028C only What is the purpose of the shading adjustment The process whereby the variations in the distribution of the lamp s light
9. types of documents may not scan properly e Curled wrinkled or folded documents Curl Feeding direction Fold Feeding direction Less than IN a Less than s e mi 5 mm 0 2 in lt a 5 mm 0 2 in ng e Perforated or punched documents e Not rectangular or irregularly shaped documents like documents with tags e Thermal or photosensitive paper e Extremely smooth shiny paper or paper that is highly textured e Carbonless paper e Creased or ripped paper e Coated paper When documents cannot be scanned properly try to change the resolution or the number of documents scanned The following types of documents must be avoided e Irregular document thickness such as envelopes e Damaged or notched document e Documents out of specified size thickness and weight e Documents containing hard attachments such as metal or plastic ex Clips or staples e Bound or glued documents e Document with wet ink or cinnabar seal ink e Paper with carbon e Cloths and plastic films e Light penetrating documents such as OHP sheet and tracing paper 18 Loading Documents E When scanning multiple sheets e Remove all staples from the document before scanning e Curled documents may cause a paper Jam or damaging the document therefore set the document flat before scanning e When scanning very important documents confirm that the number of scanned images matches the number of actual pages Documents that have been stapled Prio
10. unit Accidental spillage of liquid into the unit may cause severe damage If this occurs turn the unit off unplug the power cord and contact your dealer for service For Your Safety 4 CT Q o c O s 5 co O a O co N O N Mm O O N O N Y O co N O N a gt lt O 00 N O N 9 gt x O 09 o N o gt x L E KV S2046C S2046CU S2046CA For Your Safety Precautions E Installation Do not place the scanner in direct sunlight in a cold draft or near heating apparatus Do not place the scanner near apparatus which generate electronic or magnetic noise Protect the scanner from static electricity Do not move the scanner immediately from a cold place to a warm place It may cause dew E CD ROM e Handle a CD ROM carefully e Prevent a CD ROM from damage and keep clean E Roller Cleaning Paper e Do not store the roller cleaning paper in direct sunlight or in a place with temperature over 40 C 104 F e Only use the roller cleaning paper to clean the rollers and scanning area e f you need more information about the roller cleaning paper please refer to the Material Safety Data Sheet MSDS e Please ask your Panasonic sales company about obtaining the Material Safety Data Sheet KEEP AWAY FROM FIRE E Others e Remove all staples from the document before scanning e Do not use thinner benzine or cleaners containing abrasives or surfactants for c
11. 26C S2026CU S2026CA 9 e KV S2046C S2046CU S2046CA 1 ee 10 e Power turn on sequence aaa 11 ABOUT LED geeks er eae AG BAON ee eee e ERa EEEE we AAP k es 11 e About the SCSI setting for using SCSI interface only 12 Installing Software 44 13 e System requirements aaa 13 e CD ROM Contents aaa KAG KABAN KAKA LHT zzz zzz 13 e Complete installation 2 0 0 0 0 ccc ee ee eae 14 e All Drivers amp Utilities installation a 15 e Custom installation o26s2c522ck5o538463 Vb Sos eee SATA Aha ALENA 16 e Application installation 0 0 0 0 0 0 eee eee 17 e Viewing manuals from the CD ROM 0 00 00 e eee eee 17 e Viewing manuals installed on your computer 17 Document Specifications 2 000 ce es 18 e Acceptable documents aa 18 e Unacceptable documents aaa 18 Loading Documents 0 an 19 e When scanning multiple sheets 0 19 Clearing Paper Jams an 22 e Removing paper jams from the feeding section 22 Cleaning the Unit sss sells 24 e Outside of the scanner zzz zzz ee eee 24 e Inside the scamer eee eee 24 e Cleaning the reflector sheet for the ending sensor 24 e Cleaning the rollers and sensors ee eee 25 e Cleaning the CIS glasses and sensor rollers
12. 7 B Business card guides 9 10 20 Business card stopper 9 10 20 C Caution labels 0006 T CliSglasseS 28 Cleaning the CIS glasses 21 Cleaning the rollers 25 Cleaning the sensor rollers 27 Cleaning the sensors 25 Cleaning the unit 24 Clearing paper jams 22 Complete installation 14 Component identification 9 Custom installation 16 D DIPswitch 9 10 12 Document guides 9 10 19 Double feed detection 38 Double feed detector 26 Double feed prevention roller 26 Double feed prevention roller cover 32 Double feed prevention roller module 32 Drive rollers nananana uaaa aaa 26 42 Page E ENERGY STAR naaa aana aa 2 Exit extension tray 9 10 20 Exit stopper 9 10 20 Exit tray 0 9 10 External dimensions 39 F Feed extension tray 9 10 20 Feed tray 9 10 20 Feed tray capacity 38 For Your Safety 5 Free TOES Kaw AA Wa MAD aes 26 G Green levers 29 Image control 38 Imprinter door 9 10 Imprinter door pull 9 10
13. CU S2026CA It is highly recommended that you keep the original carton and ALL packing materials If you need to transport or ship your scanner please follow these instructions Please Note e Please use the original carton and all of the original packing materials e Improper repacking of the scanner may result in a service charge to repair the unit e The scanner should be handled in the correct horizontal position Materials Required e Original Scanner Carton amp Packing Materials e Shipping Tape and Scissors 1 Turn the power switch off and disconnect your scanner from the electrical outlet and the interface cable 2 Return the feed extension tray exit stopper and exit extension tray to their original posi tions 3 Pack the scanner Power cord e Be sure to use a pw power cord whose CD ROM shape matches the ty KV S2048C KV S2028C 1 piece shape of the electric KV S2026C S2026CU S2026CA 2 pieces outlet LO 36 Repacking Instructions E KV S2046C S2046CU S2046CA It is highly recommended that you keep the original carton and ALL packing materials If you need to transport or ship your scanner please follow these instructions Please Note e Please use the original carton and all of the original packing materials e Improper repacking of the scanner may result in a service charge to repair the unit e The scanner should be handled in the correct horizontal position Materials Required
14. Interface AA 38 L LED awa ama waa one eee AY 9 10 11 Limit mark 25 oak ee ss be oe ee ee ee 20 Loading documents 19 O Operating temperature and humidity 39 Option Consumables 39 Page pP POPO sz kem m g g randi Ba NG hiraw 38 Paper detector 26 Paper feed roller 9 10 26 Paper feed roller module 29 Power consumption 39 Powercord 4 4 4 9 10 Power requirement 39 Power switch 0 9 10 PrecautiOnNS 2 00 eee ee eee 8 R Radiation vent 9 10 24 Reflector sheets 26 Repacking 0 00 eee 36 Replacing consumables 29 Replacing the double feed prevention roller module 32 Resolution aaa 38 Roller cleaning paper 25 28 Roller exchange kit 39 S Scanning face aonana aaaea anaa 38 Scanning method 38 Scanning speed 38 SCSI connectors 9 10 SCSI setting 00005 12 SCSI terminator 0 12 Sensor rollers 23 28 34 Separation roller 26 Shading adjustment JO Specifications 38 Starting position sensor 26 STOP START button 9 10 Storage temperature and humid
15. Panasonic Operating Instructions High Speed Color Scanner Model No KV S2048C KV S2028C KV S2046C S2046CU S2046CA KV 52026C S2026CU S2026CA KV S2048C KV S2028C KV S2026C KV S2026CU KV 52046C KV 52026CA KV S2046CU KV S2046CA These instructions contain information on operating the scanner Before reading these instructions please read the Installation Guide enclosed with this unit Keep the CD ROM in the protective case Do not expose the CD ROM to direct sunlight or extreme heat and do not scratch or smudge the surface of the CD ROM Thank you for purchasing a Panasonic High Speed Color Scanner e Panasonic supports your imaging needs with a reliable and easy to use document scanner e Panasonic has developed Panasonic Image Enhancement Technology to improve the guality of your scanned images even beyond the quality of your original document illegal Duplication It is unlawful to make duplication of certain documents Duplicating certain documents may be illegal in your country Penalties of fines and or imprisonment may be imposed on those found guilty The following are examples of items that may be illegal to duplicate in your country e Currency e Bank notes and checks e Bank and government bonds and securities e Passports licenses official or private documents identification cards and the like e Copyright materials or trademarks without the consent of the owner e Postage stamps and other negotia
16. Tonal aradation Binary mode Gray scale mode 4 8 bit Dither mode 16 256 step Error diffusion 9 Note Dither and Error diffusion are executed by driver software or RTIV Image emphasis 5 step Dynamic threshold Automatic separation Noise reduction Scanner Image control Deskew Cropping Mirror image Monochrome reversing Gamma correction Note These all functions are executed by driver software or RTIV Other turiction Patch code detection Kodak patch 2 3 T Note 1 portion both side each executed only by ISIS driver 50 8 x 70 mm 2 0 x 2 8 in to 216 x 356 mm 8 5 x 14 in Size Note The setting of the paper length is possible to 25 inches in TWAIN ISIS and RTIV In case of a paper beyond legal size 1 by 1 paper scanning in the resolution under 300 dpi is recommended Paper Single paper feeding 0 05 to 0 15 mm 2 0 to 5 9 mils P Thickness Continuous paper feeding 0 06 to 0 15 mm 2 36 to 5 9 mils Note 1 mil 1 1000 in Single paper feeding 40 to 127 g m 10 7 to 33 9 Ibs Weight Continuous paper feeding 50 to 127 g m 13 3 to 33 9 Ibs Note 1 Ibs 3 75 g m Double feed detection Document length Document length SCSI III 20 MB sec SCSI III 20 MB sec Interface Transfer rate USB 2 0 USB 2 0 USB 2 0 USB 2 0 Feed tray capacity 120 sheets 64 g m 17 Ibs 100 sheets 75 g m 20 Ibs 38 Specifications KV S2046C KV S2026C KV S2046CU KV S2028C KV S2026CU KV S2046CA KV S2026CA
17. Troubleshooting Remedy ME all of the rollers See page 25 Replace the paper feed roller module and the double feed prevention roller module See page 29 and page 32 The document is curled or f lded Flatten the document and load it again after reducing the pages Make a copy of the document on speci fied paper see page 38 and scan the copy Make a copy of the document on paper of the specified size and scan the copy Load the document correctly See page 19 The CIS glasses are dirty aaa glasses The sensor rollers are dirty pana Ng fc Clean the CIS glasses and the sensor rollers See page 27 Adjust the monitor setting Clean the CIS glasses and the sensor rollers See page 27 Please change the resolution and try to scan Flatten the document The Remove Shadow or Border Removal functions may also correct the problem Refer to the PIE Reference Manual or the RTIV Reference Manual when using these functions If you still experience problems after following these suggestions please contact our Technical Support Department at 1 800 726 2797 for further assistance U S A only 41 index Page A AGAD APA 9 10 Acceptable documents 18 AccesSsorleS 0 0 ee ee es 39 ADF door 02000 2a 9 10 ADF door release 9 10 All Drivers 8 Utilities installation 15 Application installation 1
18. When you close the ADF door close it securely until the door is locked Clear the roller cleaning counter with the User Utility e After the rollers have been cleaned press the Clear Counter button in the User Utility to clear the After Clean Roller counter to zero e Refer to the User Utility Reference Manual Cleaning the Unit E Cleaning the CIS glasses and sensor rollers 0 z O ran m O Q Dm Cc gt H PJ 2 Push the ADF door release to open the ADF door 27 Cleaning the Unit Sensor roller front Clean the CIS glasses and sensor roll ers using the roller cleaning paper e If the sensor rollers are removed while cleaning re attach them after cleaning Close the ADF door e When you close the ADF door close it securely until the door is locked 28 naal a NN N SN LL K N PID XK Sensor roller front d a 5 CIS glass back Replacing Consumables E Replacing the paper feed roller module 1 Turn the power off 2 Push the ADF door release to open the ADF door 3 Push the two green levers down at both ends of the paper feed roller mod ule to unlock the paper feed rollers e When moving the green levers do not apply pressure in any other direction other than in the direction shown by the arrows Otherwise the levers may break 29 Replacing Consumables Remove the paper feed roller module strai
19. ardware wizard to complete the installation The installation process is performed automatically in Windows Vista Even if the screen Digital Signature was not found for this driver or has not passed Windows Logo testing appears continue with the installation Microsoft Windows operating system hereafter Windows 14 installing Software E All Drivers amp Utilities installation All drivers utilities and manuals can be installed at the same time using the All Drivers amp Utilities installation 1 Turn off the power of the scanner 2 Insert the CD ROM into your CD DVD drive on your computer 3 If you have a feature called Autorun activated this will start the installation process automatically Note e If tne AutoPlay dialog box is displayed in Windows Vista select CDRun exe e If the program does not automatically start click Start click Run click Browse and select the CD DVD drive containing the installation software double click on CDRun exe in the root directory to manually start the installation routine then click OK Select your scanner Select the All Drivers amp Utilities from the Installation list Follow the instructions on the screen If the screen Windows can t verify the publisher of this driver software appears continue with the installation by selecting Install this driver software anyway Turn on the power of the scanner Follow the instruc
20. atten the document and load it again as the edge of the document is curled The sensors or reflector sheets are Clean the sensors and reflector sheets dirty See page 24 The USB interface of the computer is not installed correctly The document is not loaded properly The document has been loaded on the feed tray But the scanner does not start scanning 40 Symptom Double feeding or skewing problems occur frequently or the scanner stops loading while scanning The scanned document is blank Vertical lines appear on the scanned document The scanning density is uneven The color of the scanned document is extremely different from the original document Dark spots or noise appear on the scanned documents Scanned image has moire fringes such as stripe or wavy pattern noise Portions of the edge of the scanned document are dark Possible Possible Cause The rollers are dirty The rollers have reached their life expectancy The irregular type document is to be scanned The document has a length of less than 70 mm 2 752 The document to be scanned was loaded face down upside down The CIS glasses or the sensor rollers are dirty The setting of the monitor is wrong The CIS glasses or the sensor rollers are dirty It is caused by printing pattern of the document and the congeniality of the scanning resolution The edge of document is folded or wrinkled
21. ble instruments This list is not inclusive and no liability is assumed for either its completeness or accuracy In case of doubt contact your legal counsel Notice Install your machine near a supervised area to prevent illegal duplication from being made As an ENERGY STAR Partner Panasonic has determined that this product meets the ENERGY STAR guidelines for energy efficiency However KV 52026C and KV 52046C do not comply with the ENERGY STAR Eligibility Criteria after April 1 2007 e Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries e IBM and AT are trademarks of International Business Machines Corporation in the United States other countries or both e SIS MultiStream and QuickScan Pro are registered trademarks or trademarks of EMC Corporation e Adobe and Reader are registered trademarks of Adobe Systems Incorporated in the United States and or other countries e Pentium is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries e Each company s name or company product name is each company s trademark or registered trademark The information given in these Operating Instructions is subject to change without notice Table of Contents Notice 0 cc aaa 4 Component Identification Na uu 9 e KV S2048C KV S2028C KV S20
22. due to being a trial version e When using QuickScan Pro the ISIS driver is required e The control sheets are stored as PDF files in the CD ROM provided with the scanner For use them print the control sheets in the same size as the document pages to be scanned Make sure to login to Windows 2000 Windows XP Windows Vista as an administrator 13 Installing Software E Complete installation All drivers applications utilities and manuals can be installed at the same time using the Complete installation 1 Turn off the power of the scanner 2 3 CON OQA Insert the CD ROM into your CD DVD drive on your computer If you have a feature called Autorun activated this will start the installation process automatically Note e If tne AutoPlay dialog box is displayed in Windows Vista select CDRun exe e If the program does not automatically start click Start click Run click Browse and select the CD DVD drive containing the installation software double click on CDRun exe in the root directory to manually start the installation routine then click OK Select your scanner Select the Complete from the Installation list Follow the instructions on the screen If the screen Windows can t verify the publisher of this driver software appears continue with the installation by selecting Install this driver software anyway Turn on the power of the scanner Follow the instructions of the h
23. ed line The roller cleaning paper Model No KV 5503 is available from the dealer where you purchased your scanner For supplies and accessories Call 1 866 823 0002 U S A only or your dealer 1 Turn the power off Push the ADF door release to open the ADF door ADF door release 25 Cleaning the Unit 26 4 5 6 Use the roller cleaning paper KV 5503 to remove the dirt from the surfaces of the double feed prevention roller paper SENO feed roller separation roller 6 drive o ea O rollers and 6 free rollers Remove dust on the paper sensors Paper detector Double feed detectors Waiting sensor and Starting position sensor and reflector sheets with a cotton swab Double feed Paper detector prevention roller Reflector sheets e When wiping off the dirt on the roller sur faces hold the rollers to prevent them from rotating and wipe the rollers all the way around them proceeding from one end to the other in the directions of the arrows shown in the figure on the right Double feed detector KV S2048C and KV S2028C only Drive rollers Drive rollers Paper feed roller Waiting sensor Separation roller Free rollers Starting position sensor Double feed detector KV S2048C and KV S2028C only Free rollers Make sure that the sensor rollers are installed properly before closing the ADF door e If the sensor rollers are removed re attach them Refer to page 34 Close the ADF door e
24. edure that must be emphasized in order to operate the unit safely N WARNING Power and Ground Connection The power source voltage of this unit is listed on the nameplate Only plug the unit into an AC outlet with the proper voltage If you use a cord with an unspecified current rating the unit or plug may emit smoke or become hot to the touch When you operate this product the power outlet should be near the product and easily accessible To ensure safe operation the power cord supplied must be inserted into a standard three prong AC outlet which is effectively grounded earthed through the normal wiring DOGOS GE AA The fact that the equipment operates satisfactorily does not imply that the power point is grounded earthed and that the installation is completely safe For your safety if in any doubt about the effective grounding earthing of the power point consult a qualified electrician If the plug cannot be inserted into the AC outlet contact a licensed electrician to replace the AC outlet with a properly grounded earthed one Do not defeat the purpose of the grounding earthing plug ex do not use a conversion plug Plug the power cord firmly into an AC outlet Otherwise it can cause fire or electric shock Do not pull bend rest objects on or chafe the power cord and plug Damage to the power cord or plug can cause fire or electric shock Do not attempt to repair
25. ghtly holding up the paper feed case along the groove of the feed cover to pull out the claw out of the case 5 Install the new paper feed roller mod ule with its gear on the right 1 Hang both ends of the paper feed roller module 2 While slightly lifting the paper feed roller module pass the claw along the groove of the feed cover 3 Attach the bearings at both ends of the paper feed roller module into the guide grooves of the chassis in the scanner Chassis Green levers 30 Replacing Consumables 6 Push up the green levers at both ends in the direction of the arrows until they click into place e After installing the paper feed roller mod ule confirm that the feed rollers can be moved lightly in vertical direction Close the ADF door e When you close the ADF door close it securely until the door is locked 31 Replacing Consumables E Replacing the double feed prevention roller module 1 Turn the power off 2 Push the ADF door release to open the ADF door 3 Remove the double feed prevention roller cover 4 Remove the double feed prevention roller module in the direction of the arrow Wo Hd Pel 5 ad iP k Mi Ve c Double feed prevention roller module M 32 Replacing Consumables 5 Install the new double feed prevention roller module by matching the groove of its shaft with the groove of the metal holder Make sure that both ends of
26. his appliance must be earthed IMPORTANT The wires in this mains lead are coloured in accordance with the following cord Green and Yellow Earth Blue Neutral Brown Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol 2 or coloured Green and Yellow The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N or coloured Black The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L or coloured Red How to replace the fuse Open the fuse compartment with a screwdriver and replace the fuse For Your Safety To prevent severe injury and loss of life read this section carefully before using the unit to ensure proper and safe operation of your unit E This section explains the graphic symbols used in this manual Denotes a potential hazard that could A N WARN l N G result in serious injury or death Denotes hazards that Id It i i N CAUTION ises minor the unit These symbols are used to alert operators to a specific operating procedure that must not be performed These symbols are used to alert operators to a specific operating proc
27. hroughly wrung e Do not use thinner benzine or cleaners Radiation vent containing abrasives or surfactants 3 Remove dirt and dust from the radia tion vent with a brush E Inside the scanner e Clean the unit at least once a week or when 20 000 sheets have been scanned whichever comes first e Clean the rollers and sensors if paper jamming or multiple sheet feeding occurs frequently Refer to pages 25 26 e Clean the CIS glasses and sensor rollers when lines appear on the scanned images Refer to pages 27 28 e If the documents you scan are dirty then the scanner components will also become dirty To maintain proper scanning clean the scanner components frequently E Cleaning the reflector sheet for the ending sensor Remove dust on the reflector sheet of the ending sensor with a cotton swab e The reflector sheet is behind the center of the paper release rollers Oe CG Paper release roller Cotton swab TI aa 24 Cleaning the Unit E Cleaning the rollers and sensors Roller cleaning paper Open the bag on the dotted line and take out the roller cleaning paper e If the roller cleaning paper bag is left opened for a long period of time before using it the alcohol will evaporate Please use the roller cleaning paper immediately after opening the bag e Before using the roller cleaning paper please read the safety information on the Operation Manual enclosed with the roller cleaning paper Dott
28. ity 39 T Tonal gradation 38 Troubleshooting 40 Page U Unacceptable document 18 USB cable 36 39 USB connector 9 10 User Utility 26 33 W Waiting sensor 26 WGIQNL ee saad a se tad em e E ANA eee ses 39 43 Panasonic Communications Company of North America Unit of Panasonic Corporation of North America One Panasonic Way Secaucus New Jersey 07094 Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario LAW 213 Panasonic Business Systems U K A Division of Panasonic U K Ltd Willoughby Road Bracknell Berkshire RG12 8FP Panasonic Marketing Europe GmbH Hagenauer Strasse 43 65203 Wiesbaden Germany For information of Compliance with EU relevant Regulatory Directives Contact to Authorised Representative Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg Germany Panasonic Corporation Web Site http panasonic net Panasonic Communications Co Ltd 2007 F1108FS0
29. leaning the outside of scanner Co Component Identification E KV S2048C KV S2028C KV S2026C S2026CU S2026CA Document guides Imprinter door for KV S2048C only LE AG ADF door Paper feed roller Z S ADEd Feed tra a oor release ST HA STOPISTART button Feed extension n A KA LED Radiation vent tray eT S ENS Business card stopper p Exit extension D Exit stopper 328 AK Ser Power switch Business card guides Exit tray Imprinter door pull ka mK for KV S2048C only Z Imprinter door AC inlet Y p USB connector for KV S2048C only TS Ae SCSI connectors DIP switch for KV S2026C S2026CU for KV S2026C S2026CU S2026CA only S2026CA only Power cord Plugs vary in shape among countries Note e KV S2048C and KV S2028C have only USB interface Component Identification E KV S2046C S2046CU S2046CA Document guides Imprinter door BA TE ADF door Paper feed roller Z LIU CU ka st lt ADF door release Feed tray ss SS PS SA a SS STOP START button Feed extension _ xm LED tray my Business card FQ stopper E P Nd f Exit stopper gt LA NI AN a P p Radiation vent f NG LL Power switch Exit extension tray Business card guides Exit tray Imprinter door pull Z Imprinter door USB Bf DIP switch SCSI connectors Power cord Plugs vary in shape among countries AC inlet
30. ller cleaning paper fluid including isopropyl alcohol The roller cleaning paper may be harmful to sensitive skin Please use protective gloves Do not use the roller cleaning paper near a heater or open flame CAUTION The unit should be used only with the power cord enclosed with the unit When the unit is not used over an extended period of time switch it off and unplug it If an unused unit is left connected to a power source for a long period degraded insulation may cause electric shock current leakage or fire Installation and Relocation SOO AJDO O A Do not position the unit in a location where it is unstable To prevent fire or shock hazard do not expose this unit to rain or any type of moisture Do not place the unit in a hot humid or dusty environment Prolonged exposure to these adverse conditions may cause fire or electric shock When moving the unit be sure to unplug the power cord from the AC outlet If the unit is moved with the power cord attached it can cause damage to the cord which could result in fire or electric shock Do not use the tray hanging out of a table When carrying the unit do not use the trays as handles When carrying the unit hold the both side grips Operating Safeguards If the unit falls down or gets damaged turn the unit off and unplug the power cord Otherwise it may cause fire or electric shock Do not place any liquids or heavy items on the
31. ocument guide This may cause a paper jam or skew 20 Loading Documents Adjust the document guides to the size of the documents Set documents under the paper feed roller 1 Lift the lever of the paper feed roller as shown in the figure 2 Push documents in the direction of the arrow until they stop under the paper feed roller 21 Clearing Paper Jams Torn documents thin documents or documents that are creased on the top edge may cause paper jams If a paper jam occurs remove the jammed sheet according to the following procedure E Removing paper jams from the feeding section Remove all documents from the feed tray Push the ADF door release to open the ADF door ADF door release Remove the jammed document e If the jammed document remains at the feed tray side pull it up e If the jammed document appears at the exit tray side remove it from the exit side CN A sit ME AG Zo mai 22 Clearing Paper Jams Make sure that the sensor rollers are installed properly before closing the ADF door e If the sensor rollers are removed re attach them Refer to page 34 Close the ADF door e When you close the ADF door close it securely until the door is locked 23 Cleaning the Unit E Outside of the scanner Clean the unit at least once a month 1 Turn the power off 2 Clean the cover with a soft cloth e Please use a water dampened cloth that has been t
32. per KV SS03 Imprinter Unit Imprinter Unit KV SS032 KV SS020 The scanning speed depends on the test environment The scanning speed differs depending on the host computer operating environment or application 2 To change the paper feed roller module and double feed prevention roller see below Option Consumables 1 E Changing the paper feed roller module and double feed prevention roller To ensure long performance Panasonic recommends changing the paper feed roller module and double feed prevention roller after 300 000 sheets have been scanned If double feeding or paper jamming occurs frequently even after roller cleaning please call your dealer and order a Roller Excahnge Kit e Before replacing each roller refer to Replacing Consumables on page 29 39 Troubleshooting If a problem occurs while the unit is being used check the following items and check the scanner status by User Utility If the unit still malfunctions turn it OFF unplug the power cord and call for service Symptom Possible Cause Remedy Problem with the AC outlet Check and reset the circuit breaker The LED does not light when the power The power cord is not plugged in Insert the power plug firmly switch is turned ON AA AA Disconnect the scanner from the elec p ppYy tric outlet and call for service The scanner is not connected to the Connect the cables correctly computer correctly Uninstall the scanner from PC The
33. quantity are transformed into a fixed output within the scanning range is known as shading adjustment It can be carried out by means of the User Utility using the special shading paper which is provided with this scanner When shading adjustment is required Proceed with the compensation when the colors in some parts of the scanned images differ in the extreme or when the image quality fails to be improved even after the inside the scanner is cleaned Before proceeding with the shading adjustment Before proceeding be absolutely sure to thoroughly clean the CIS glasses transport path drive rollers free rollers and sensor rollers using the roller cleaning paper If the shading adjustment is carried out while these parts are still dirty it will not be possible to eliminate the lines that form on the scanned images Shading adjustment procedure 1 Start the User Utility 2 Click User Shading on the main menu and operate as the image display dictates For further details refer to User Shading section in the User Utility Reference Manual Caution If the scanned images are still lined after the shading adjustment has been performed and if these lines are not elim inated even after the ADF glass areas have been cleaned it means that the shading has not been compensated properly Clean the parts again and then proceed with the shading adjustment 35 Repacking Instructions E KV S2048C KV 52028C KV S2026C S2026
34. r to scanning remove all staples and paper clips together or stacked together as in a from pages file folder will need to be separated 1 Fan the stack of documents to sepa rate all the edges 2 Hold both ends and bend the docu ments as shown in the illustration 3 To flatten the documents hold firmly and pull them apart as shown in the illustration Repeat these steps as necessary 2 Carefully align the documents 3 Adjust the document guides slightly larger than the actual size of the docu ments Document guides 19 Loading Documents When scanning paper longer than the feed tray pull out the feed extension tray from the feed tray and the exit extension tray as shown in the figure on the right e The exit extension tray of KV S2046C KV S2046CU and KV S2046CA is fixed Adjust the position of the exit stopper e When using small sized documents like business cards raise the business card guides and the business card stopper Caution Do not use the business card guides and the business card stopper for larger documents than their acceptable size It will cause paper jams Business card guides Business card stopper 5 Place the documents on the feed tray with the side to be scanned facing up Limit mark e Be sure to place the documents on the Paper feed roller feed tray as shown in the figure on the right e The amount of documents should not Feed tray exceed the limit mark on the d
35. scanner is not registered correctly Register the scanner hardware again See page 14 The computer does not recognize the scanner Check your computer whether the SCSI card is installed correctly using the device managers property The same ID number is used for the Use the different SCSI ID numbers for scanner and the other device each devices If the scanner is the last device in the SCSI chain set the DIP switch of SCSI terminator to Enable If the scanner is not the last device in the SCSI chain set the DIP switch of SCSI terminator to Disable The computer cannot recognize the SCSI card SCSI connection The terminator is not set correctly Turn the computer OFF Turn the scan ner ON and then turn the computer ON again The scanner was turned on after the computer was turned on Check the computer whether the USB interface of your computer is correctly using the device manager s property OR CONNECUON The scanner is connected via USB hub Do not connect via USB hub ies _ without High Seed logo is s6 the cable with High Speed logo Scan speed is slow at USB connection Hh SEAKNETIS CONNEC UA SES Connect with USB 2 0 The ADF does not open when the ADF The ADF door is not closed broperl Push the ADF door release again after door release is pushed a a you close the ADF door until it is locked Load the document correctly See page 19 The sensor cannot detect the document l l Fl
36. the power cord or plug If the power cord or plug is damaged or frayed contact an authorized service representative for a replacement Ensure that the plug connection is free of dust In a damp environment a contaminated connector can draw a significant amount of current that can generate heat and eventually cause fire if left unattended over an extended period of time Never touch the plug with wet hands Danger of electric shock exists Stop operation immediately if the unit emits smoke excessive heat abnormal smell or unusual noise These conditions can cause fire or electric shock Immediately turn the unit off and unplug the power cord and contact your dealer for service When disconnecting the unit grasp the plug instead of the cord Pulling on a cord forcibly can damage it and cause fire or electric shock For Your Safety Operating Safeguards 999 A If metal fragments or water gets into the unit turn the unit off and unplug the unit immediately Contact your dealer for service Operating the contaminated unit can cause fire or electric shock Do not open covers and do not attempt to repair the unit yourself Contact your dealer for service Do not alter the unit or modify any parts Alteration or modification can cause fire or electric shock During thunderstorms do not touch the unit and plug It may cause an electric shock Roller Cleaning Paper 6 Do not drink or inhale the ro
37. tions of the hardware wizard to complete the installation The installation process is performed automatically in Windows Vista CON OQA Even if the screen Digital Signature was not found for this driver or has not passed Windows Logo testing appears continue with the installation 15 Installing Software E Custom installation Each driver utility and manual can be installed using the Custom installation selection as reguired 1 Turn off the power of the scanner only when installing Device Driver 2 Insert the CD ROM into your CD DVD drive on your computer 3 If you have a feature called Autorun activated this will start the installation process automatically Note e If tne AutoPlay dialog box is displayed in Windows Vista select CDRun exe e If the program does not automatically start click Start click Run click Browse and select the CD DVD drive containing the installation software double click on CDRun exe in the root directory to manually start the installation routine then click OK 4 Select your scanner 5 Select the Custom from the Installation list Select a driver an utility or a manual If the screen Windows can t verify the publisher of this driver software appears continue with the installation by selecting Install this driver software anyway 7 Follow the instructions on the screen When installing device driver proceed following steps 8 Turn on the power
38. ul interference in which case the user will be required to correct the interference at his own expense FCC Warning To assure continued FCC compliance the user must use only shielded interface cable and the provided power supply cord Also any unauthorized changes or modifications to this equipment would void the user s authority to operate this device For your safety please read the following text carefully For United Kingdom only This appliance is supplied with a moulded three pin mains plug for your safety and convenience A 5 amp fuse is fitted in this plug Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362 Check for the ASTA mark B or the BSI mark on the body of the fuse If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced If you lose the fuse cover the plug must not be used until a replacement cover is obtained A replacement fuse cover can be purchased from your local Panasonic Dealer If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safely There is danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket If a new plug is to be fitted please observe the wiring cord as shown below If in any doubt please consult a qualified electrician WARNING T

Operating Instructions (English)

Contents

Download Pdf Manuals

Related Search

Related Contents