Home

INSTALLATION MANUAL

1. Ill Installation procedures 1 Turn off the machine and unplug the power cord from the power outlet 2 Remove the right side rear upper cover from the copier three screws Image transmission Softswitch LED connector L Copier LAN cable port Port 2 AOYEIXCOO6DA lt Softswitch gt Lights up when the image controller is running or is ready to be used When turned on the image controller system starts up When turned off the image controller system AOYEIXCO08DB safely shuts down Note e If the image controller malfunctions or cannot be shut off with the softswitch be sure to 3 If the fax kit has been installed loosen the two unplug the power cord from the electrical outlet screws and then remove the circuit board from or the machine s power cord connector the copier e Remove the seal from the connector of the WAIT AW N power cord ANY Ay W ANY gt N Mni LAY MK LAA NK AQ s WY N ANW W AOYEIXCO09DA Y110511 5 Installation Manual 7 Remove the two screws for the main circuit board Note The two screws removed here will be used to install the relay circuit board 4 Remove the rear right cover four screws pee 8 Attach the two supplied shoulder screws for mounting
2. These functions can be used from the image con troller The function limitations are not applied to the image controller 1 Use the supplied copier LAN cable crossover cable to connect the LAN port of the copier to port 2 of the image controller 2 Use a network cable to connect port 1 of the image controller to the hub LAN J m YM AOYEIXCO35DA lt Copier Network Settings gt Since the IP address of the copier can be set from the image controller it is not necessary to specify the IP address from the copier The IP address of the copier appears at the end of the Configuration Sheet for the image controller However the DHCP settings must be specified from the copier in order for the copier and image controller to communicate internally through the crossover cable e Specifying the copier DHCP setting Utility mode Administrator Settings Network Settings TCP IP Settings IPv4 Settings Auto Input DHCP Settings ON In order to use the network functions of the copier the network settings on the copier must be specified according to the functions to be used Y110511 5 Note e When manually specifying the IP address of the image controller Since the IP address of the copier is one num ber higher than the IP address of the image controller consecutively numbered IP addresses must be available Example Imag
3. Tighten the two lower screws first AOYEIXCO66DA Y110511 5 E 5 Installation Manual 22 Connect the supplied image transmission cable to the copier AOYEIXC067DA 23 Attach the supplied ferrite core to the indicated position on the image transmission cable AOYEIXCO68DA 24 Close the door of the cover 25 Connect the other end of the image transmission cable to the image controller AOYEIXCO69DA lt 110 127 V regions gt 26 Plug the copier and image controller power cords into an outlet Installation Manual E 6 lt 220 240 V regions gt 26 Connect the image controller power cord to the copier AOYEIXE072DA 27 Plug the copier power cord into an outlet IV Specifying the copier settings From the copier specify the necessary settings for using the image controller lt Image Controller Settings gt 1 Turn on the machine by using the auxiliary power button and the main power switch Display the Service Mode screen For details on displaying the screen refer to the Service Manual Touch System 2 Touch Image Controller Setting Touch Controller 1 Touch END Touch Exit Turn the copier off then on again If the copier has not been turned off the setting changes are not applied 2 110511 5 V Connecting the copier and image co
4. Be sure to use the two screws removed in step 7 AOYEIXC017DA 12 Using the two supplied shoulder screws for the relay circuit board connector secure the connec tor of the relay circuit board c alf AOYEIXC018DA To install the covers and other parts removed in steps 4 and 5 reverse the removal procedure If the fax kit was removed in step 3 install it at the location from where it was removed Remove the knockout from the cover removed in step 2 with nippers AOYEIXC061DA E 4 110511 5 16 Install the cover removed in step 2 four screws 19 Connect the furnished power cord to the image 17 Remove the mounting brackets from the image controller power cord connector and secure the controller five screws power cord plug with the clamp 110 127 V regions power cord B 220 240 V regions power cord A Note Be sure to use the furnished power cord Power cord for Taiwan that utilizes 110V power is not supplied as an accessory part AOYEIXCO64DA 20 Insert the two image controller tabs into the AOYEIXCO82DA holes on the machine cover 18 Attach the furnished upper and lower mounting brackets to the image controller five screws removed in step 17 AOYEIXCO65DA 21 Screw the image controller to the cover four fur nished screws B AOYEIXCO63DA N ote
5. are limited Note Use a network cable Category 5E or later recom mended to connect to a computer Connecting the copier and image controller with separate LAN cables With this connection method the network func tions of the copier are not impaired and the image controller functions are added The IP address settings for the copier and image controller are specified separately In order to use the network functions of the copier the network settings on the copier must be specified according to the functions to be used Use a network cable to connect the LAN port of the copier to the hub LAN Use a network cable to connect port 1 of the image controller to the hub LAN Note Depending on the connection method the image controller TCP IP settings are different For details refer to step 11 in VI Specifying basic image con troller settings IP address m gt ju hi i 3 3ld09 AOYEIXC034DA Installation Manual Connecting the copier and image controller with the supplied copier LAN cable cross over cable and connecting the image con troller to a hub LAN With this connection method the following copier function limitations are applied e AppleTalk and IPX SPX protocols IPv6 IPsec browsing for file transmissions SMB and replies to broadcasts e The 1000Base T network speed cannot be used
6. removed in step 3 install it at the location from where it was removed 16 Remove the rear lower cover six screws AOYEIXC042DA 17 Remove the right side rear lower cover two J screws AOYEIXCO46DA 18 Remove the center cover from the right side rear lower cover removed in step 17 two screws AOYEIXC043DA Y110511 5 19 Remove the two brackets from the copier two screws each Note The four screws removed here will be used to install the image controller AOYEIXC044DA lt Attaching the image controller to MF651 in all regions and MF551 MF451 in regions that utilize 127 to 240V power gt When attaching the image controller to MF551 MF451 in regions that utilize 110 to 120V power follow the step 20 in page E 6 and later 20 Remove the connector cover from the rear lower side of the copier The connector cover is shown by the arrow in the illustration below AOYEIXE036DA 21 Connect the supplied power cord for connection between copier and IC to the connector Power cord AOYEIXE051DA Y110511 5 22 Insert the harness into the wire saddle Wire saddle AOYEIXE052DA 23 Fix the end of the ground wire included in the power cord for connection between copier and IC to the copier screw furnished with the video interface kit AOYEIXE053
7. the relay circuit board to the main cir cuit board AOYEIXC014DA WA AOYEIXC012DB 6 Remove the interface connector cover for the copier one screw Do not use the removed connector cover AOYEIXC015DB 9 Mount the supplied relay circuit board as shown in the illustration AOYEIXC013DB AOYEIXCO16DA Y110511 5 E 13 Installation Manual 10 While aligning the matchmarks on the relay cir cuit board and the main circuit board connect the connector coming from the back side of the relay circuit board to the connector on the main circuit board NRO wD 967 AOR BBP DARA SP 925 9297 Rs Woe RAM 4 BABA 11 Using the two screws secure the relay circuit board Note Be sure to use the two screws removed in step 7 is ror AOYEIXC017DA 12 Using the two supplied shoulder screws for the relay circuit board connector secure the connec tor of the relay circuit board AOYEIXC018DA Installation Manual 13 Reinstall the internal bracket that has been removed in step 5 11 screws 14 Reinstall the rear right cover that has been removed in step 4 four screws 15 If the fax kit was
8. DA 24 Install the image controller on the copier four screws Note Be sure to use the four screws removed in step 19 Threaded hole Chiggico ra Ou Omen oMe none ne none nexonenexononexone AOYEIXE038DB Installation Manual Installation Manual 25 Connect the other end of the power cord to the connector on the image controller Note No need to secure the connector of the power cord with the clamp Jii r OPO E A 20 SSS y AOYEIXE039DA 26 Connect the supplied image transmission cable to the copier AOYEIXC026DA 27 Attach the supplied ferrite core to the indicated position on the image transmission cable Reinstall the right side rear upper cover removed in step 2 three screws Reinstall the right side rear lower cover removed in step 17 two screws Connect the other end of the image transmission cable to the image controller AOYEIXE040DA 31 Close the right side rear upper lower covers 32 Reinstall the rear lower cover that has been removed in step 16 six screws 33 Plug the copier power cord into a power outlet lt When attaching the image controller to MF551 MF451 in regions that utilize 110 to 120V power gt 20 Install the image controller on the copier four
9. Server Setup in the Controller Details screen Without specifying any other settings touch Exit When Save Changes appears select Yes and then select OK 10 In the same way select Network Setup After selecting Protocol Setup then IPv4 Setup select Ethernet Setup Set Enable AutolP Configuration to No and then select OK Y110511 5 Specify settings for the following IP Address Image controller IP address Subnet Mask Subnet mask for the con nected network Gateway IP address of the default Address gateway Obtain IP for Set whether to obtain the IP Engine address of the copier The setting is different depending on the connec tion method used in V Connecting the copier and image controller to a network a No b Yes If Yes is selected the IP address of the copier appears next to Engine IP Address included in Device Information on Configuration Sheet Note First check with your network administrator for the settings that should be entered 12 Touch Menu three times select Yes when Save Changes appears and then select OK 13 Touch Printer Setup 14 Touch Menu select Yes when Save Changes appears and then select Ok 15 When Exit Setup is selected Rebooting sys tem appears and the image controller is restarted 16 After the image control
10. Settings TCP IP Settings IPv4 Settings Auto Input DHCP Settings ON In order to use the network functions of the copier the network settings on the copier must be specified according to the functions to be used Installation Manual Note e When manually specifying the IP address of the image controller Since the IP address of the copier is one num ber higher than the IP address of the image controller consecutively numbered IP addresses must be available Example Image controller 192 168 1 10 Copier 192 168 1 11 However Xxx xXx Xxx 255 cannot be specified for the IP address of the image controller if it is set manually When using DHCP to specify the IP address of the image controller Use the IP address assigned by the DHCP server for the IP address of the image controller and copier Depending on the connection method the image controller TCP IP settings are different For details refer to step 12 in VI Specifying basic image controller settings IP address With this connection method be careful of the tim ing for turning on the image controller and the copier For details on the timing refer to the end of this manual VI Specifying basic image controller set tings IP address Specify the default settings for the image controller Turn on the image controller Turn on the copier Language Setup appears in the lower center of the screen in th
11. VI 50 5 IC 41 2 Video Interface Kit Image Controller INSTALLATION MANUAL Index VI 505 IC 412 d Color MF360 MF280 Accessory parts Il Part names Ill Installation procedures IV Specifying the copier settings V Connecting the copier and image controller to a network VI Specifying basic image controller settings IP address VII Checking the setup with a test print VI 505 IC 412 d Color MF651 MF551 MF451 Accessory parts Il Part names Ill Installation procedures IV Specifying the copier settings V Connecting the copier and image controller to a network VI Specifying basic image controller settings IP address VII Checking the setup with a test print Y110511 5 E i Installation Manual This page is intentionally left blank Installation Manual E ii Y110511 5 VI 505 IC 41 2 Video Interface Kit Image Controller INSTALLATION MANUAL Applied Machines d Color MF360 MF280 COLOR MFP 36 ppm 28 ppm Product Code AOED I Accessory parts Before starting to set up check that the following are included Only the parts required to install the image controller appear in the package contents list Package contents of the image controller Fiery IC 412 No Name Q ty 1 Image controller Power cord A AOQOHIXCO19HA Power cord B 1 for the wall outlet A00HIXE034HA Copier LAN cable crossover cable Di Image transmissio
12. and image controller to a network the copier and image controller communicate internally through a crossover cable If the DHCP function is enabled on the image con troller the network interface card in the copier per forms a DHCP request when it is turned on in order to acquire the IP address necessary for communi cating with the image controller Since a DHCP request is performed when the copier is turned on the IP address cannot be acquired if the copier is turned on before the image controller is ready to be used preventing communications with the image controller One of the following IP addresses can be assigned to the copier 172 17 249 2 10 249 249 2 Y110511 5 E 9 Installation Manual This page is intentionally left blank Y110511 5 E 10 Installation Manual VI 505 IC 41 2 Video Interface Kit Image Controller INSTALLATION MANUAL Applied Machines d Color MF651 MF551 MF451 COLOR MFP 65 ppm 55 ppm 45 ppm Product Code AOPO AOP1 A0P2 l Accessory parts 3 The accessories are not used when installing the image controller Before starting to set up check that the following are included Package contents of the video interface kit Only the parts required to install the image controller VI 505 appear in the package contents list No Name Q ty Package contents of the image controller Fiery IC 412 1 Relay circuit board No Name Q ty 1 Image controller Power
13. cord Forconnection between copier and IC Screw 4 x 8mm Power cord 1 Shoulder screws for mounting the relay circuit board AOYEIXCOOSDB Shoulder screws for the AOOHIXE034HA relay circuit Copier board connec LAN cable tor AOYEIXC047DA crossover Installation cable manual AOOHIXCO18HA Image transmission cable 4980IXCO19DA ADYEIXCOOSDA Using or not using the part depends on each amp WARNING AOYEIXCO54DA AOQOHIXCO19HA Power cord 2 for the wall outlet Other accesso After unpacking be sure to get rid of the ries 3 packaging materials and keep them out of the reach of children Putting the head in the plastic bag image controller involves danger of suffocation This power cord cannot be used in Taiwan that utilizes 110V power This power cord is not used when installing the Y110511 5 E 11 Installation Manual lt Port descriptions gt ll Part names Port 1 Ethernet 10Base T 100Base TX 1000Base T network port Port 1 Port 2 AOOHIXC033HB Port 1 For the LAN Connect the network cable to the LAN Port 2 For the COPIER Use a crossover cable to connect to the LAN port of Power the copier l l This port is not used depending on the connec cord con i nector tion method Refer to page E 8
14. e controller 192 168 1 10 Copier 192 168 1 11 However Xxx xxx Xxx 255 cannot be specified for the IP address of the image controller if it is set manually When using DHCP to specify the IP address of the image controller Use the IP address assigned by the DHCP server for the IP address of the image controller and copier Depending on the connection method the image controller TCP IP settings are different For details refer to step 11 in VI Specifying basic image controller settings IP address With this connection method be careful of the tim ing for turning on the image controller and the copier For details on the timing refer to the end of this manual VI Specifying basic image controller set tings IP address Specify the default settings for the image controller Turn on the image controller Turn on the copier Language Setup appears in the lower center of the screen in the copier s touch panel Press the Utility Counter key on the copier Touch Controller Details Note If Controller Details does not appear wait a short while and then repeat steps 3 and 4 6 In the Language Setup screen select the lan guage and market region After the settings have been specified the con troller reboots When the password is entered the Setup screen appears The default password is Fiery 1 Be sure to type in the password with the correct cap italization Select
15. e copier s touch panel Press the Utility Counter key on the copier Touch Controller Details Note If Controller Details does not appear wait a short while and then repeat steps 3 and 4 In the Language Setup screen select the lan guage and market region After the settings have been specified the con troller reboots Touch Controller Details When the password is entered the Setup screen appears The default password is Fiery 1 Be sure to type in the password with the correct cap italization Select Server Setup in the Controller Details screen 10 Without specifying any other settings touch Exit When Save Changes appears select Yes and then select OK 11 In the same way select Network Setup After selecting Protocol Setup then IPv4 Setup select Ethernet Setup Set Enable Auto IP Configuration to No and then select OK Installation Manual E 8 12 Specify settings for the following IP Address Image controller IP address Subnet Mask Subnet mask for the con nected network Gateway IP address of the default Address gateway Obtain IP for Set whether to obtain the IP Engine address of the copier The setting is different depending on the connec tion method used in V Connecting the copier and image controller to a network a No b Yes Note First check with your network administrator
16. ear upper cover removed in step 2 three screws 25 Reinstall the right side rear lower cover removed in step 17 two screws 26 Connect the other end of the image transmission cable to the image controller Se 9 l AOYEIXC031DB 27 Close the right side rear upper lower covers 28 Remove the knockout plate from the cable pass through opening in the lower rear cover and then install the rear lower cover to the copier six screws io AOYEIXCO045DA 29 Plug the copier and image controller power cords into a power outlet IV Specifying the copier settings From the copier specify the necessary settings for using the image controller lt Image Controller Settings gt 1 Turn on the machine by using the auxiliary power button and the main power switch 2 Display the Service Mode screen For details on displaying the screen refer to the Service Manual Touch System 2 Touch Image Controller Setting Touch Controller 1 Touch END Touch Exit Turn the copier off then on again If the copier has not been turned off the setting changes are not applied Installation Manual V Connecting the copier and image con troller to a network The network functions of the copier can be used even when the image controller is installed There are two ways of connecting to a network from this copier When connection b is used some func tions
17. er LAN cable cross over cable and connecting the image con troller to a hub LAN With this connection method the following copier function limitations are applied e AppleTalk and IPX SPX protocols IPv6 IPsec browsing for file transmissions SMB and replies to broadcasts e The 1000Base T network speed cannot be used These functions can be used from the image con troller The function limitations are not applied to the image controller 1 Use the supplied copier LAN cable crossover cable to connect the LAN port of the copier to port 2 of the image controller 2 Use a network cable to connect port 1 of the image controller to the hub LAN m e Wo 3ld09 AOYEIXC071DA lt Copier Network Settings gt Since the IP address of the copier can be set from the image controller it is not necessary to specify the IP address from the copier The IP address of the copier appears at the end of the Configuration Sheet for the image controller However the DHCP settings must be specified from the copier in order for the copier and image controller to communicate internally through the crossover cable e Specifying the copier DHCP setting Utility mode Administrator Settings Network
18. for the settings that should be entered 13 Touch Menu three times select Yes when Save Changes appears and then select Ok 14 Touch Printer Setup 15 Touch Menu select Yes when Save Changes appears and then select Ok 16 When Exit Setup is selected Rebooting sys tem appears and the image controller is restarted 17 After the image controller is ready to be used turn the copier off then on again VII Checking the setup with a test print After setting up the image controller print the config uration sheet to check that the controller is operating correctly lt To print a test page gt 1 Press the Utility Counter key on the copier 2 Touch Controller Details 3 Touch Menu 4 Select Print Pages The names of the pages that can be printed are displayed Select Configuration Y110511 5 Timing for turning on the copier with con nection method b from V Connecting the copier and image controller to a network Turning on Turn on the devices in the following order 1 Turn on the softswitch on the image controller 2 Check that the image controller is ready to be used and then turn on the copier If the copier is turned on too soon a malfunction may occur For details refer to the following infor mation Timing for turning on the copier With connection b described in V Connecting the copier
19. gnificant change or problem with the procedure ll Part names __Ethernet 10Base T 100Base TX 1000Base T network port Port 1 Power cord con nector Image transmission Softswitch LED connector _ Copier LAN cable port Port 2 AOYEIXCOO6DA Installation Manual E 2 lt Softswitch gt e Lights up when the image controller is running or is ready to be used When turned on the image controller system starts up When turned off the image controller system safely shuts down Note e If the image controller malfunctions or cannot be shut off with the softswitch be sure to unplug the power cord from the electrical outlet or the machine s power cord connector e Remove the seal from the connector of the power cord lt Port descriptions gt Port 4 Port 2 Port 1 For the LAN Connect the network cable to the LAN AOOHIXC033HB Port 2 For the COPIER Use a crossover cable to connect to the LAN port of the copier This port is not used depending on the connec tion method Refer to page E 7 Y110511 5 lil Installation procedures 1 Turn off the machine and unplug the power cord from the power outlet Remove the cover from the right side of the machine as shown in the illustration four screws 2 AOONIXC024DA 3 If the fax kit has been installed loosen
20. ler is ready to be used E 19 turn the copier off then on again Installation Manual VII Checking the setup with a test print After setting up the image controller print the config uration sheet to check that the controller is operating correctly lt To print a test page gt 1 Press the Utility Counter key on the copier 2 Touch Controller Details 3 Touch Menu 4 Select Print Pages The names of the pages that can be printed are displayed Select Configuration Timing for turning on the copier with con nection method b from V Connecting the copier and image controller to a network Turning on Turn on the devices in the following order 1 Turn on the softswitch on the image controller 2 Check that the image controller is ready to be used and then turn on the copier If the copier is turned on too soon a malfunction may occur For details refer to the following infor mation Timing for turning on the copier With connection b described in V Connecting the copier and image controller to a network the copier and image controller communicate internally through a crossover cable If the DHCP function is enabled on the image con troller the network interface card in the copier per forms a DHCP request when it is turned on in order to acquire the IP address necessary for communi cating with the image controller Since a DHCP request is performed
21. n troller to a network The network functions of the copier can be used even when the image controller is installed There are two ways of connecting to a network from this copier When connection b is used some func tions are limited Note Use a network cable Category 5E or later recom mended to connect to a computer Connecting the copier and image controller with separate LAN cables With this connection method the network func tions of the copier are not impaired and the image controller functions are added The IP address settings for the copier and image controller are specified separately In order to use the network functions of the copier the network settings on the copier must be specified according to the functions to be used Use a network cable to connect the LAN port of the copier to the hub LAN Use a network cable to connect port 1 of the image controller to the hub LAN Note Depending on the connection method the image controller TCP IP settings are different For details refer to step 12 in VI Specifying basic image con troller settings IP address DG 2g ALG o AOYEIXCO70DA Y110511 5 E 7 Connecting the copier and image controller with the supplied copi
22. n cable AOYEIXC003DA Ferrite Core amp AOYEIXCO54DA Other accesso ries 2 This power cord cannot be used in Taiwan that utilizes 110V power The accessories are not used when installing the image controller Y110511 5 Package contents of the video interface kit VI 505 No Name Q ty 1 Relay circuit board Power cord Forconnection between copier and IC Screw A 4 x 8mm Shoulder screws for mounting the relay circuit board AOYEIXCO0SDB Shoulder screws for the relay circuit board connec tor AOYEIXC047DA Upper mount ing bracket eee AOYEIXCO74DA Lower mount ing bracket AOOHIXC105HB Screw B 3 x 20 mm 9J08IXC075DA Installation manual D 4980IXC019DA This part is not used when installing the video interface kit on d Color MF360 MF280 Installation Manual WARNING After unpacking be sure to get rid of the packaging materials and keep them out of the reach of children Putting the head in the plastic bag involves danger of suffocation WD Note This manual provides the illustrations of the acces sory parts and machine that may be slightly differ ent in shape from yours In that case instead of the illustrations use the appearance of your machine to follow the installation procedure This does not cause any si
23. screws Note Be sure to use the four screws removed in step 19 Threaded hole Omen OMe noXOMe none nexononexononexone te le elercertce sty epbererteehceece Ceci cece eeceeCceceeceecet Leelee Cercer cate ofCereeleclcetterccec cel ter ce Ce Ce Cee eese h Ep cecce cceccecceccecCeeCeet eee eke Ceeltece CeeCee Ce Ce lester ee hee ke te Ce CeeCee nce Ce CeeCee Ce eeecceccecceeccectettectectee efcegteetceecectentee cektertee teehee cece cette ttc et ceecce Cece Cee cekCcet ce cece eek eek cceteeKcecee cece ce CCE eeeceSceecceece ce Cee Scotts ecce Cee cecCeeccecceeteetee CeeCeeceeeCceCeecceeCeecee C CeeCeec CeeCee CeeCee ekeebcectcetcececgte e Seegeceseegtcete eecebeee e eect AOYEIXC029DB Y110511 5 21 Plug the supplied power cord for the wall outlet into the power cord connector on the image con troller and then secure the cord with the clamp Note e Be sure to use the supplied power cord for the wall outlet e Power cord for Taiwan that utilizes 110V power is not supplied as an accessory part AOYEIXCO30DA 22 Connect the supplied image transmission cable to the copier Peay Ji Ieee AA 6 es 25 AOYEIXC026DA 23 Attach the supplied ferrite core to the indicated position on the image transmission cable Y110511 5 24 Reinstall right side r
24. the two screws and then remove the circuit board from the copier AOYEIXC073DA 4 Remove the cover from the back of the machine as shown in the illustration four screws AOYEIXCOS6DA Y110511 5 E 3 5 Remove the internal bracket 12 screws AOYEIXC057DA 6 Remove the interface connector cover for the copier one screw Do not use the removed connector cover AOYEIXCO58DA 7 Remove the two screws for the main circuit board Note The two screws removed here will be used to install the relay circuit board i A AOYEIXC014DA Installation Manual Installation Manual 8 Attach the two supplied shoulder screws for mounting the relay circuit board to the main cir cuit board AOYEIXC015DB 9 Flip the switches 1 and 2 up as shown in the illus tration Note If the switches are not flipped up this option can not be detected properly AOYEIXCOS9DA 10 Mount the supplied relay circuit board as shown in the illustration Note Align the matchmark of the relay circuit board with that of the main circuit board Connect the connec tor located on the back of the relay circuit board to the connector on the main circuit board AOYEIXCO60DA 11 Using the two screws secure the relay circuit board Note
25. when the copier is turned on the IP address cannot be acquired if the copier is turned on before the image controller is ready to be used preventing communications with the image controller One of the following IP addresses can be assigned to the copier 172 17 249 2 10 249 249 2 Installation Manual E 20 Y110511 5

INSTALLATION MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents