Installation manual Video interface
Contents
1. amp MU EDIA 5604 EB Eindhoven 14 TECHNICAL SUPPORT All our products are manufactured under strict quality control Each device is being tested before shipment If nevertheless do occur problems or f you have technical questions contact us directly under Distribution by NavInc Technical support email info navinc nl Technical support tel 0031 0 40 7511912 In addition to constant product update and development related changes the instruction manuals of the devices are constantly edited and kept up to date To enable us to provide you with the right information and support for the device you have got at hand please add the following information to every inquiry Date of purchase your name and address item number and the type of your vehicle 15 WARRANTY The product s designed for automotive use and his environment The warranty of the product 1s one year No warranty e not break the labels attached on the board e Damaged of the interface e Own reperations e Modified cables 15 TECHNICAL DATA Software version R2 1 Voltage supply 12V DC and 24VDC Voltage operating capacity 8 24 V Standby current 0 mA Operating current 12 W Power input 12 W Temperature range 30 C up to 80 C Weight 2508 Dimensions W x H x D 13x50 mm NavInc Pagina 182. the CID s turned off Reset function Multi functions push button for selecting and configuring of video sources Can be fitted anywhere in the car Car PC serial port for controlling video interface In this case the multi function push button will be optional NavInc Pagina 2 NavInc P O Box 4063 5604 EB Eindhoven 2 IMPORTANT INFORMATION Installation must be done by a qualified personnel This interface should be used to display fixed menus during your journey for example the MP3 menu for DVD upgrades The driver of the vehicle must never be distracted by moving pictures In most countries states watching movies whilst driving is prohibited Therefore we do not accept any liability for material damage or personal injury resulting directly or indirectly from the installation or the operation of this TV free interface Battery power 12V to the interface is fused by a value of 5mA Power of the interface must be ignition power 15 The best way to take the power is from the fuse box Use the device only at a 12 volt vehicle electrical system Make sure to have a proper ground The device should not be set up in direct proximity of heat sources e g power amplifier Please make sure that no objects or liquids can intrude the interior of the device Danger of short circuit Please follow all caution advises contained in the mounting guidelines Please read through all safety instructi
3. NTN INT P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven Installation manual Video interface Designed for Vectra Signum systems Version 1 0 0 Content 1 Features 2 2 Important information 3 3 Installation amp Safety instructions 3 4 Scope of Delivery 4 5 Product features 4 6 Compatibility 4 7 Wire diagram 5 8 Requirements 7 9 Installation 7 10 Activation 15 11 Note 15 12 FAQ 16 13 Adjustment 17 14 Technical support 18 15 Warranty 18 16 Technical data 18 NavInc Pagina 1 NIAVING P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven 1 FEATURES 1 Input Spec MULTI VIDEO INTERFACE 3 x Video Input External video source 1x REAR CAMERA Input Rear camera source 1x REAR CAMERA Input S Video Rear camera source x CID Input Car system Input 1 x Opel Input 2 Output Spec x CID output 3 Power Spec Input Power 8VDC 12VDC Consumption Power I2WATT Max 4 Switch Input mode Automatic detection and switching to the video source for rear view camera Possible to switch Input mode with Remote control Automatic detection and switching to main CID image for viewing caller s name Opel Phone car kit 5 Extra features Configuration for a reverse camera which does not render the image in the mirror Image luminosity adjustment Down the consumption of the battery while the CID controller displays the image or when
4. e ignition or the colors are not displayed correctly or the selected video input are not displayed the CID has to be removed again for rechecking Please refer to chapter FAQ NavInc Pagina 15 NavInc NAV NG P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven 12 FAQ 1 Usual CID screen has strange colors or no image what can I do Probably the jumper cables are not inserted properly Remove the jumper cables from K1 CID and K2 LCD and insert them again carefully Probably one of the color signals red green or blue is not arriving at the TFT display Remove the CID Interface board from the CID and examine the solder pads of the FCCconnectors 30 pole K1 and K2 especially the pins 4 7 In case of a bad joint try to resolder the particular pad 2 The push button 1s not switching the external video sources The interface male connector was not inserted properly or in the right position Check the position and re insert it 3 External video screen has strange colors or no image Probably the TFT jumper cables are not inserted properly Remove the jumper cable from K2 LCD and insert them again carefully 4 External video screen is white black Your video device is configured to PAL TV system In this case go to the setup menu of the video device and select NTSC TV system Otherwise you have to replace the video device 5 The video interface is not switching properly the main CID and ext
5. eo signals Otherwise you get the image like the picture NavInc Pagina 14 NavInc NAV NG P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven 10 ACTIVATION Standard Control Functions The video interface is controlled by the available push button It main function is to select for displaying the auxiliary video sources and CID one by one as follow 1 At start up the interface will display the main CID information 2 Select Video Input 1 press the button short time when on the TFT is displaying the main CID information 3 Select Video Input 2 CVBS press the button short time when on the TFT is displaying the video input 1 4 Select CID press the button short time when on the TFT is displaying the video source 2 11 NOTE In order to execute the first test run you need to connect the car battery again When switching on the ignition the usual Opel logo etc should appear in the CID Pay special attention to the colors of the CID display they must not be strange or missing Press and release shortly the push button in order to switch the CID to display the Ist video input Press again and select the 2nd video input and again to come back to the CID display If this test looks OK the CID Interface with its jumper cables seems to be installed correctly and the battery must be disconnected again to continue the installation If you should not see any picture in the CID even after switching on th
6. ernal video screens push button rear view camera Telmute Try to reset the interface as indicated in Section Video Interface Control Functions Check the wiring of Rear view camera and Telmute signals 6 The video interface is switching the external video screen but back screen is showing The back screen has a horizontal thin white line which means no signal is presented at the selected video input Check the video out signal NTSC of the device with your home TV LCD or TV Navinc Pagina 16 NavInc N AU NL P O Box 4063 5604 EB Eindhoven 13 AJUSTMENT In addition of selecting the video input sources the push button can be used also for controlling the interface and the screen as follow Control brightness Increase the brightness by pressing the button longer than 2s when on the screen is displaying one of the two video input sources There are available 5 levels 0 to 4 The default value is 2 After level 4 the brightness will go back to level 0 The value will be kept also after ignition is turned off Reset interface Press the button longer than 2 seconds when on the screen is displaying CID information The reset is not visible for the user After reset the brightness level is set to the default value 2 Mirroring the image Press the button longer than 2seconds while the screen is displaying the video signal from rear view camera NavInc Pagina 17 NavInc NAV NG P O Box 4063 N ATION
7. he arrows on the connector are positioned right BUTTON The best position 1s near to cigarette lighter but it can be fitted any ware in dash After that you can wire the backlight of button to the power supply of ashtray LED Probably you have to cut and reconnect again the wires of push button during installation Color Connection E White 5V or 12V ignition from backlight ge li Push Button Brown Ground l Connect the black data plug with the interface cable Navinc Pagina 13 NavInc NAV NL P O Box 4063 NAVIGATI N amp MULTIMEDIA 5604 EB Eindhoven POWER SUPLY 1 Connect the power cable of the interface as followed Color Connection Red 12V ignition power reverse lamp Black Ground Green Ground White Telephone Mute Make sure that the camera signal is good 12V signal otherwise the camera relay on the interface is ticking VIDEO INPUT VIDEO IN 1 Video input must be connected with an A V source DVD player DVB T tuner Ipod front camera AUS inelare Ingany VIDEO IN 2 CVBS Video input must be connected with an A V source DVD player DVB T tuner Ipod front camera VIDEO IN 2 S VIDEO Audio video input must be connected with an A V source DVD player DVB T tuner Ipod front camera R CAM Video input must be connected with a rear camera Note Video interface can be working stand alone to connect only a rear camera Use onlye NTSC vid
8. near to the top of plastic frame approx 3 4 cm in vertical position The free end of the jumper cable approx 1cm can now be bended by 90 to horizontal position Navinc Pagina 10 NavInc NAV NG P O Box 4063 5604 EB Eindhoven urn NAVIGATION A MULTIMEDIA 15 Next step the controller board of the CID can be inserted again The original jumper cable that is still connected to the controller board must also be folded as shown in the picture yellow arrow to bring the open end directly bellow the end if the new jumper wire coming from the TFT display After folding the original jumper wire of the controller board you should verify if it still sits properly inside the connector and if it is not skewed 16 Before installing the CID interface board isolation must be prepared over capacitors indicated in the picture with red line in order to avoid contact between the CID Interface board and the CID controller board otherwise a short might damage or destroy the CID during operation 17 Take the CID interface board from kit and put it over CID controller board Both jumper cables must be connected to the connectors of the CID Interface the TFT jumper cable to K2 LCD connector the controller board cable to K1 CID connector The jumper cables must not cross themselves or be swapped by 180 Both connectors do have a locking slider that must be pushed out first before inserting a jumper cable When inserting the jum
9. no CDC40 Opera CD70navi DVD90 DVD100 Please check www navinc nl for more details NavInc Pagina 4 NavInc P O Box 4063 5604 EB Eindhoven 7 WIRE DIAGRAM Power cable Telephone mute Camera 12V A V cable Yellow cinch Black cinch Video input two CVBS R CAM white cinch Camera input rear NTSC Control Port Switch Red Black connector Interface connector 5V 12V Backlight NavInc Pagina 5 NavInc NAV NG P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven Video Input 2 S Video Control Port Viden Int 7 CVBS Interface Control 4pins male RCA male Good Video Input RVC Relay Rear View Cam Reversing Lamp 12V RVC control TELMUTE Control Signal yellow Backlight 5V 12V red Multi Function Push Button Optional Naine Pagina 6 NavInc NAV NG P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven 8 REQUIREMENTS 1 Check if the interface is compatible with you system 2 When you receive this package you have to check whether there s any parts not included and you have to contact us right away 3 Get the right installation tools 9 INSTALATION Please read through all instructions and handling directions intently before installation and start up of the device The interface must be installed inside the CID between the LCD and Controller Turn igni
10. ntroller board by 180 to the top red arrow NavInc Pagina 9 NavInc NAV NG P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven 11 Now you have to remove the CID TFT by clicking it out from the 3 clamps marked with the red arrows 12 View and flip it carefully as indicated in the picture After that you can see the 30 pole jumper cable connected to the TFT display 13 Now you have to pull out the 30 pole jumper cable connected to the TFT display by pushing the white slider of the connector away from the connector in parallel to unlock the jumper cable red arrows This can be done with the fingertips of both hands Then the original jumper cable can be pulled out of the connector with no force After that you can move to installation steps 14 The new jumper cable from the Opel interface kit must be pushed into this connector and locked with the white slider by pushing it towards the connector It is absolutely necessary to insert the new jumper cable into the connector in parallel until the end of its travel It must not be skewed otherwise it might cause a short and destroy the CID The CID TFT can be inserted again and the new jumper cable must be putted through the holes of the shielding plate as shown in the picture Because the new jumper cable is too long it must be folded as shown in the picture It does not harm the jumper cable if it is folded The free end of the jumper cable should
11. ons and handling directions intently before installation and start up of the device Check alway the compatibility of the interface for your car before installation You can check the compatibility on www navinc nl or call NavInc for support 3 INSTALLATION amp SAFETY INSTRUCTIONS Before starting any installation work you must wait 90 seconds after turning the ignition switch to the LOCK position and disconnecting the negative terminal from the battery When disconnecting the battery the saved addresses and radio stations of the navigation system will not be deleted just the settings of board computer BC1 and BC2 will be lost NavInc Pagina 3 NavInc N AU NL P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven 4 SCOPE OF DELIVERY Package Power Input cable 1x Switch 1x Flat cable 1x Sub boardl 1x Serial cable 1x 3 screws 3x Installation instructions 1x 5 PRODUCT DESCRIPTION Video interface Opel This interface is used for Opel navigation systems The interface alloy you to connect video sources to the navigation screen Input Specificities x S Video input x Rear camera input 2x V NTSC Input 6 COMPATIBILITY 6 1 Car models The interface is compatible for Opel navigation system Please check www navinc nl for more details 6 2 Navigation system The interface 1s compatible for the Opel navigation systems CD30 CD30 MP3 CD50 CD50 pho
12. per cables into the connectors take care that they are not skewed and fully inserted Then push the slider back towards the connector to lock it The slider might not be locked properly in the middle so it is recommended to push the middle of the slider with a small screwdriver towards the connector to assure proper locking NavInc Pagina 11 NavInc NIN NTs es HAVIGATION 8 MULTIMEDIA 18 If this is done put on the rear shielding plate carefully without moving the CIDInterface out of its position Now insert both special screws from kit into CID board holes and under interface board holes using a tweezers as indicated in the picture 19 After that you have to screw them until the rear shielded plate is fixed Insert the torx screws through both interface holes and screw them into special screws n order to fix the interface to the CID See picture 20 You have to do the same with the left corner After that screw the other two torx screws to the opposite holes of rear shielding plate 21 Don t forget to attach green wire to the torx screw as indicated in Figure 17 Attached Cables for proper ground isolation 22 The interface male connector is indicated with yellow arrows in the picture NavInc Pagina 12 NavInc NAV NG P O Box 4063 NAVIGATION amp MULTIMEDIA 5604 EB Eindhoven 23 Connect the 12 pins and 6 pins interface connector to the interface sub board Note Make sure that t
13. tion OFF and wait a couple of minutes before installation Attention do not install the interface when the ignition is ON l Use OEM unlocktools optional to take out the radio unit 2 Remove the airco unit 3 Remove the center console Start with the 4 torkx srews NavInc Pagina 7 NavInc NAV NG P O Box 4063 NAVIGATION 8 MULTIMEDIA 4 Pull the center console back warts The console is locked with 4 lockers 5 Dissemble the 2 torx screws of the CID Disample the screen 6 Pull out the plastic frame 7 Take off the screen Unscrew the 4 torx srews Navinc Pagina 8 NavInc NV ING 5604 EB Eindhoven HAVIGATION 8 MULTIMEDIA 8 After that open the CID by unscrewed and taking off the four Torx screws on the rear shielding plate The following work must be done with special care not to destroy the CID You should discharge yourself from electrostatic energy by touching e g the water pipe prior to open the CID Also you should not wear clothes that support charging with electrostatic energy like wool pullovers etc 9 After removing the rear shield plate of the CID you can see the CID controller board and the 30 pole jumper cable that connects the CID TFT and CID controller It has to be spitted 10 Next step is to take out the CID controller boards and CID TFT In order to do that you must first unplug the power connector for the TFT display bellow Yellow arrow and flip the co
Download Pdf Manuals
Related Search