Subminiature GPS Vehicle Tracker User Manual
Contents
1. Install the various functions as needed according to the above wiring diagram If you only need the most basic positioning function just connect to the vehicle power supply Optional accessories cut off relay SOS alarm switch MIC Saati verre jaaet ver a A 5 e II Product Characteristics e GPS vehicle location e GSM 850 900 1800 1900MHz e High sensitivity highly integrated GPS chip e Low energy consumption e Fast signal acquisition e Support single location and continuous tracking e Support the fence alarm e Support location information query through SMS and the Internet e Locate the user by telephone or through SMS ePress the SOS button for precise positioning in an emergency II Product Specifications 3 1 Technical specifications GSM module GSM 850 900 1800 1900MHz GPS sensitivity 159dBm GPS center frequency L1 1575 42MHz GPS positioning accuracy 5 25m Speed accuracy 0 1 m s Time accuracy In syne with GPS Default data WGS 84 Hot start ls Cold start 38 s Maximum altitude 18000 m Maximum speed 515 m s Acceleration of gravity lt 4g 3 2 Other specifications Operating temperature 20 65 C Humidity 5 95 Dimensions mm 50 45 21 Voltage 12V 24V Average standby current Less than 80MA LED Power supply work status indication External alarm switch SOS Chapter III Introduction of2. negative connected to GND Pin 3 Relay control output positive voltage 12V forbidden from connecting to GND during operation Pin 4 Relay control output negative connected to GND Pin 5 Debug port RX signal Pin 6 Debug port TX signal Pin 7 Emergency alarm signal input SOS high level under normal circumstances low level input to enable SOS alarm Pin 8 External status signal input TA low level under normal circumstances high level input indicates occurrence of external events Pin 9 Overall power on signal input ON high level under normal circumstances low level input to enable power on Pin10 External input signal reference ground connected to GND Pin11 External microphone input positive MIC Pin12 External microphone input negative MIC Pin13 External battery input positive BAT input voltage 3 6 4 2V the equipment may be permanently damaged if the input voltage exceeds the specified range Pin14 External battery input negative BAT connected to GND 2 Installation of SIM card Remove the shell and install the SIM card as illustrated below Beveled Corner of SIM Card Installation of SIM Card Completed Installation of SIM Card _ 3 After the SIM card is installed close the shell tightly connect the wires and turn on the equipment GPS antenna Notice The motherboard indicators and the light slots of the shell shall be aligned with GPS antenna facing upwards Al Note
3. Location Modes Vehicle tracker is a multifunctional GPS positioning product which integrates voice call SMS positioning and GPRS positioning services The operating instructions of the SMS and GPRS positioning are as follows I Operating instructions of SMS positioning a Send the message instruction 666 user password to the terminal and then the terminal will return a message about the latitude and longitude For example When 6660000 is sent the returned data format is as follows Lat latitude N S latitude value accurate to five decimal places Long longitude E W longitude value accurate to five decimal places Speed KM H accurate to two decimal places Direction direction of course accurate to two decimal places Date YYY Y MM DD Time HH MM SS Greenwich time BS base station information FIX location status A V ID IMEI STATE information state Example of valid data Lat N22 6189 Long E113 6333 Speed 0 17 KM H Direction 62 58 Date 2008 06 17 Time 09 39 45 BS 27970eb3 FIX A ID 123456789000001 STATE SMS Display the location on the map point to point mode Open the IE then key in http maps google com to log onto GOOGLE map website and input the latitude and longitude on the upper left corner For example 22 544N 113 9107E Note If degrees and minutes format is used the degrees and minutes shall be separated by a space Googl em A is the
4. old Description After the instruction is executed the terminal will change the user password according to the user s requirements password 8 P 8 q After successful setting 770 CONFIG OK will be returned to the phone if the password is wrong 770 PASSWORD ER will be returned e g 770 1111 0000 After the instruction is executed the user password changes from 0000 to 1111 801 letters or numbers 0 20 digits user password Change the user name under the GPRS mode Description After the instruction is executed the user name of the terminal under the GPRS mode will be set according to the requirements After successful setting 801 CONFIG OK will be returned to the phone if the password is wrong 801 PASSWORD ER will be returned e g 801 13900139000 0000 After the instruction is executed the user name is 13900139000 802 APN letters or numbers 4 20 digits login user name 4 20 digits login password letters or 4 20 letters or numbers numbers digits user password Set the APN Description After the instruction is executed the terminal APN under the GPRS mode will be set according to the requirements After successful setting 802 CONFIG OK will be returned to the phone if the password is wrong 802 PASSWORD ER will be returned e g 1 802 CMNET 0000 After the instruction is executed the terminal APN is CMNET the login user name a
5. After successful setting the mobile phone will receive the message amp 711 amp CONFIG OK amp amp returned by the terminal e g 1 711 13800000001 13800000002 13800000003 0000 e g 2 711 1380000000 1 0000 After successful setting the terminal returns 711 CONFIG OK to the mobile phone if the password is wrong 711 PASSWORD ER will be returned 720 alarm mode 0 3 user password Set the terminal alarm mode Alarm mode 0 No alarm Alarm mode 1 Dialing alarm Alarm mode 2 Message alarm Alarm mode 3 Dialing alarm Message alarm Note When the back cover is removed or the SOS alarm switch is turned on the terminal will give an alarm according to the preset alarm mode e g 720 3 0000 After the instruction is executed the terminal alarm mode is set as dialing alarm message alarm when the alarm message is sent the first preset number will also be dialed After successful setting the terminal returns 720 CONFIG OK to the mobile phone if the password is wrong 720 PASSWORD ER will be returned Note The default alarm mode of the terminal is 0 that is no alarm 730 interval number of pieces of data returned user password 730 0 1 0000 the GPS is turned off and the timed return function is deactivated 803 fixed IP address port number user password Set the server address under the GPRS mode Instruction for setting 988 server a
6. Subminiature GPS Vehicle Tracker User Manual Table of Contents Chapter L Foreword euiar olebed See th seek dene EE ERN E RAEE 2 KONCI EV a e eE aae a e atom er sce vy NO A NNER 2 MW PRECAUTIONS EE A E T T E T 2 Chapter II Equipment Introduction cece eee e cence eee ee eee eneneeneeneeneeaeeas 3 TQunck Gide sirit ra si E E E degen aaia r asia neat Mah athe Gens 3 II Product Characteristics cceceesceceeceneeneeneeneeeeneeeeeneeneteeneeneeneeneeas 5 ILL Product S pecifications seie snanar iai i Rn EKAA ER A EAER 6 Chapter III Introduction of Location Modes ecc eee ee cece ee ee eee eneeeeneeneenees 7 I Operating instructions of SMS positioning ce cece cece cence eee eee 7 II Operating process for viewing the location through the Internet 8 Chapter IV Operation of Other Functions cece eceee eee ee ene ee eee eeeeneeneneen anes 11 I Query through mobile phone 0 cece cece cree e rene eens ee ee ene ea ees 11 II Oil cut off power off functions cece cece eee cence eee ne neta ete neeaea ees 11 Chapter V Instruction Setos ceres yere ccc cece ence enen iia ipea aeai iaia Eeen 11 a RETTO ARAETA EA A AE tee ole EAEN AA EAT 18 Chapter I Foreword I Overview Are you worried about your car being stolen It is likely that your favorite car attracts car thieves Although you may have insured your car it can
7. ddress 988 www gps02 com 80 user password This instruction is used to set the GPRS center server address The server address can either be a fixed IP whose format is xxx xxx XXX XXX or a domain name whose length is less than 64 bytes After successful setting amp 803 amp CONFIG OK amp amp will be returned to the phone if the password is wrong amp 803 amp PASSWORD ER amp amp will be returned e g 803 119 149 149 114 30000 0000 It can also be set through the domain name e g 803 jk jy 100 com 30000 0000 Note This product has a factory set server address and the instruction shall be used with caution 666 user password Single location query a message about the latitude and longitude will be returned 111 user password Description After the instruction is executed the terminal according to the settings will read the data and status information of the base station in the place where the terminal is located The data and status information of the base station will be returned according to the following format base station information information of 1 base station n 1 digit status bit 4 digit user password requested number e g 25738841 25708 3d 25738709 1 0000 13900139000 223 user password The terminal activates the oil cut off or power off function 233 user password The terminal deactivate the oil cut off or power off function 770 new password
8. e value accurate to five decimal places Long longitude E W longitude value accurate to five decimal places Speed KM H accurate to two decimal places Direction direction of course accurate to two decimal places This message is returned after the instruction 666 user password is sent When you call the terminal with a mobile phone phone number preset number and hang up the phone after ringing 2 5 times the terminal will return a message about the latitude and longitude Date YYY Y MM DD Time HH MM SS Greenwich time BS base station information FIX location status A V ID IMEI STATE information state Precautions 1 This equipment is of non waterproof design 2 The equipment shall work under the GSM GPRS network environment 3 Make sure that there is sufficient balance in the SIM card account so as to avoid inconvenience 4 The equipment can not work under power off status or outside the service area even you are a registered user 5 This equipment supports GPS and GSM GPRS dual positioning mode 6 Please use this equipment in the areas permitted by law Any consequence arising from violation of the laws shall be solely borne by the user Note As this product adopts a GPS module of high sensitivity it is normal for drift in the case of weak GPS signal
9. ease refer to the installation instructions for the relay a Send the message instruction 223 user password to the terminal and then the terminal will return a message RF3 OK The terminal will turn on the oil cut off or power off function b Send the message instruction 233 user password to the terminal and then the terminal will return a message RF3 OFF The terminal will deactivate the oil cut off or power off function Note In order to avoid accidents please take care to use the oil cut off power off instruction especially during driving Chapter V Instruction Set 70X user password X refers to Description The user can switch between the work modes through the work mode this instruction When X is 0 point to point mode is set when X is 3 GRPS mode is set Remarks The default mode of the equipment is 3 710 center number user password Description The center number setting instruction is set by the operator for the normal operation of the terminal under the center mode e g 710 10665 1 2000 0000 After the instruction is executed the center number is set as 1066512000 After successful setting the terminal returns 710 CONFIG OK to the mobile phone if the password is wrong 710 PASSWORD ER will be returned 711 phone number 1 phone number 2 phone number 3 user password Set the preset numbers through the message sent by a mobile phone
10. nagement problems make the transportation process visible transparent and controllable prevent the drivers frauds and irregularities and improve the utilization of vehicles save transportation time reduce fuel consumption costs improve goods delivery accuracy and increase customer satisfaction Featured by compact size exquisite design and high location precision this product can be easily installed and secured It is very suitable for prevention of car theft monitoring and management of logistics vehicles Prior to use this product please take a few minutes to read this user manual so as to understand the operational details and get better service II Precautions 1 Please read this manual carefully for correct operation 2 You need to choose a safe place to install this product and some dangerous places such as automobile airbag are not suitable for placing this product otherwise damage to the driver or passengers may occur 3 This manual is just for your reference The contents and operating steps described in this manual may be different from that of the actual product please refer to the actual product Chapter II Equipment Introduction I Quick Guide 1 Definition of external wiring PIN 1 V RL RX SOS ON MIC BAT PIN 13 gt eet oe pul A are i AV Ze WOES PIN 2 V RL TX TA GND WIC BAT PIN 14 Pin 1 External power input positive voltage range DC 6V 24V Pin 2 External power input
11. nd password are blank e g 2 802 CCDLEN QIUXIA 21 RX 0000 After the instruction is executed the APN is CCDLEN the login user name is QIUXIA 21 and the login password is RX Note The default APN of this product is CMNET 75 l fence radius meter sampling interval minute latitude longitude user password Set the electronic fence Description After successful setting 751 CONFIG OK will be returned if the password is wrong 751 PASSWORD ER will be returned e g 751 5000 5 2232 6208N 11354 6378E 0000 After the instruction is executed the fence of 5 km radius is set for the terminal when the terminal leaves the area the fence alarm message will be sent to the center number 752 user password Read the electronic fence After the instruction is successfully sent the terminal reads the work status data of the fence and returns it to the phone If the password is wrong amp 752 amp PASSWORD ER amp amp will be returned e g 752 0000 The following will be returned open 1 lat 22 54368N Ing 113 91063E distance 500 time 5 status 2 Wherein open 1 refers to the activation of the fence open 0 refers to the deactivation of the fence lat 22 54368 refers to the latitude N S Ing 113 91063 refers to the longitude E W distance 500 refers to the radius of the fence time 5 refers to the sampling interval status 2 refers to that the terminal gets valid
12. not make up for the frustration due to loss of your favorite car Are you worried that your cars are deceitfully leased out and can not be recovered You have many cars for rent and could have stayed at home comfortably to collect rent however the existence of swindlers always make your feel uneasy fearing that your car is not returned on schedule and the lessee disappears together with your car Are you racking your brains to improve the operational efficiency of you fleet It is a widely well known fact that the drivers usually disregard considerable waste of company resources in the process of transportation however it is difficult to supervise them closely on the way of transportation Although a variety of regulations are formulated you still can not completely exclude all kinds of false phenomena The above problems can be readily solved when the subminiature GPS vehicle tracker is used For private cars this product can help you locate your car in time so that you can contact the police to recover your car There are many successful cases of car recovery thanks to the use of our product For the cars for rent purpose this product can achieve monitoring unknowingly Just sitting at home you can know about the location and driving speed of your car so that timely recovery of your car can be achieved based on the monitoring information in case of deceitful lease or theft For the logistics vehicles this product can easily solve many ma
13. satellite data and the fence works normally status 1 refers to that the fence is activated but the terminal fails to get valid satellite data status 0 refers to that the electronic fence is not set 760 user password Cancel the electronic fence Description After the instruction is executed the terminal cancels the fence function After successful setting the terminal returns 760 CONFIG OK to the phone If the password is wrong 760 PASSWORD ER will be returned e g 760 0000H 90 1 Read the user parameters HOO2HH Read the GPRS parameters 904HH Connect to the GPRS HOOSHH Disconnect to the GPRS 92 L H Activate the transmission timing After the instruction is sent a parameter is added during GRPS transmission and the number of minutes calculated by the internal timer will be sent to the center After the transmission timing is activated 15 digit EMI code user name status bit password data type data size base station information latitude longitude speed course data time number of timed minutes Note The number of timed minutes is expressed with 7 digits HO22HH Deactivate the transmission timing After the instruction is sent the original transmission mode will be restored Normal transmission mode 15 digit EMI code user name status bit password data type data size base station information latitude longitude speed course data
14. specific location displayed on the map II Operating process for viewing the location through the Internet The user can operate the GPS tracker through the Internet Positioning Service Center jk jy100 com provided by us Here you can check the location information query costs historical records control amp management items etc Operating process Log onto the website jk jy100 com key in your account number and password click on Login to enter the global positioning system For first logon please register in our service center gt RERAN MS 350657459896535 R Se gcgag we ER Enter the operating interface Q 0 46 POM Se eee eo ee Ao ee Bee mt wee peewee 7 amen sA at aa Double click to select the terminal and the terminal position will be displayed on the map directly Click on Get Position to get the current position Click on Playback to view the historical track aa ane l gt 4 SS S eos Chapter IV Operation of Other Functions I Query through mobile phone When you call the terminal with a mobile phone phone number preset number and hang up the phone after ringing 2 5 times the terminal will return a message about the latitude and longitude To use this function the calling number display function of the SIM card shall be subscribed II Oil cut off power off functions For the installation method pl
15. time HO23 H Activate the timing control After the instruction is sent the timing control will be activated When the status bit of the terminal is high the transmission interval keeps unchanged when the status bit is low the transmission interval will be adjusted to 1 5 of the normal interval 924HH Deactivate the timing control After the instruction is sent the timing control will be deactivated When the status of the terminal returns to normal the transmission interval will not be controlled by the status bit 15 digit EMI code user name status bit password LPD data size base station information latitude longitude speed Low voltage back transmission function and it is a low voltage alarm message course data time 15 digit EMI code user Timed back transmission function and it is a data message name status transmitted back on a timed basis bit password AUT data size base station information latitude longitude speed course data time 15 digit EMI code user name status bit password SOS data size base station information latitude longitude speed course data time SOS alarm function and it is an SOS alarm message 15 digit EMI code user name status bit password OUT data size base station information latitude longitude speed course data time It is an alarm message indicating the vehicle is out of the fence Lat latitude N S latitud
Download Pdf Manuals
Related Search