LI-PO BALANCER USER MANUAL
Contents
1. X LI PO BALANCER amp user MANUAL Special features ADVANCED BALANCING PROGRAM Li Po Balancer controls the charging current adequately to equalize the voltage of each cell in the battery pack being charged by the intemal microprocessor To do this may drain the current to drop the voltage of the cell being higher Li Po Balancer communicates with every X 15 chargers via temperature sensor port of the charger so can monitor the voltage of each cell at the display screen of the charger COMPATIBILITY WITH OTHER BRANDS OF CHARGER Li Po Balancer can be used with any of chargers having Li Polymer charging function But you need to pay attention to operate the Li Po Balancer properly to equalize the voltage perfectly Please read Warning and safety notes carefully SELF BALANCING WITHOUT THE CHARGER Li Po Balancer can be self operative without linking to charger When you connect the battery pack to the individual port of Li Po Balancer the balancing job will be started instantly In this case the individual cell voltages will be equalized to the least cell voltage of the battery pack But if the voltage of peculiar cell is less than 3 0V it will be ignored And the balancing job will be performed without the cell LED DISPLAY Five red LED s represent each of five cells will blink on discharging Agreen CHECK LED will be blinking during the process And they show error status also please refer LED indication Connection2. diagram Example for 2 series Example for 3 series Example for 5 series When the battery pack connected to Li Po Balancer there should not be short circuit on individual port The circuit of Li Po Balancer will be damaged When used with other brand of charger the connection diagram is same except Chager link cable Use aright connector that matches with the battery pack being charged among connectors On operating of self balancing you do not need to connect the output of battery pack to any port When the job finished all LED s will not blink anymore There will not be the buzzer sound to avoid from wasting the current that may cause imbalance LED indication Normal status Drain status 1 gt Check LED blinking one times regularly 2 gt 1 5 cell LED s blinking when discharged 1 cell O Error status 2cell O 1 gt When the battery pack is connected to Li Po Balancer the processor recognize cells are above 2 0V Then all appropriated LED s and Check LED will blink three times But if the 3cell O voltage of any one cell is detected below 2 0V for about 60 seconds by any reason Check LED Ace will blink twice and the buzzer sounds twice repeatedly This status will be continued until the problem is eliminated Or the job will be terminated forcibly to protect the battery 2 gt if the voltage of any peculiar cell is higher than 4 23V during the job Check LED will blink
3. one time 5 cell and the beep will sound one time repeatedly until the voltage goes to below 4 23V But if this happens we recommend to stop the procedure And you need to perform the self balancing with the battery pack before doing the job again Check O 3 gt If the pin assignment of battery pack or the connector has a faulty connection LED of corresponding Error cell and Check LED will keep on blinking until the error is removed 4 gt The blinking LED indicates discharging during balancing job All LED will be off at the completion of balancing job Warnings and safety notes gt Be sure that every components are connected to be connected properly Please refer the connection diagram Use the right connector that suits with the battery pack being charged to link to Li Po Balancer gt The internal FET s emit heat which can cause the temperature of unit raise Li Po Balancer should be set up ona head resistant non inflammable and non conductive surface Never place them on a car seat carpet or similar Keep all inflammable volatile materials well away from operating area gt Using Li Po Balancer with other brand of charger than X 15 series You need to set charge current lower than 0 5A regardless of the battery s capacity at your charger If you do not so the voltage of battery being charged may raise higher instantly because of higher feeding current As a result the final voltage of battery pack can be calculated from the s
4. um of voltages of each cell then the charger will finish the process before the completion of balancing Even though Li PO Balancer is employed with other charger than X 15 series chargers every basic function operates normally except the safety function and monitoring the individual voltages provided by X 15 charger 3 YEAR LIMITED WARRANTY HONG KONG ONLY TLP HONG KONG LIMITED WWW TLP HK
Download Pdf Manuals
Related Search