USER MANUAL
Contents
1. 0 6 M6 11 M6x10 E Stand n 2 6 M6x20 a In option 18 M6 a ref 052284 2 cross bars 4 ref 98359 COMPOSITION COMBI 230 PRO 39 02 39 04 PRO 230 PRO 400 SA 052451 Set of 2x 55mm extension joints 1 COMBI 230 PRO ONLY 052284 Standfordentpuler 1 050045 Auhok2 1 1 050051 Inertia hammer for glue puller 050938 Alu hook 1 051683 STRAIGHTENING LEVER AND BAR CHOOSE YOUR BAR OR YOUR LEVER STRAIGHTENING POWER Straightening lever Straightening bar Pulling bar ref 050686 ref 050693 ref 050716 N 4 awe 7 d a d For areas when the sheets To straighten or maintain a To straighten or maintain a are thin Ex door fender sheet under stress after sheet under stress after using using the pulling bar the pulling bar lt f A T t x 4 AZ li B a 1 u d L 4 at 3 8 For angles and rounded corners Change the original pads for the double ones ref 050723 Adaptable on Straightening bar Pulling bar For wide areas ex utility vehicle side panel Replace the original traction bar 0 8m by the 1 2 m bar ref 050730 1 2 Adaptable Straightening bar a T Pulling bar Exemple of application CHOOSE THE RIGHT STRAIGHTENING PROCESS Principles 4 8 Compariso2. USER MANUAL 4 71 Sy E V E EE 21 GYSLINER GYSLINER 39 02 GYSLINER 39 04 GYSLINER PRO 230 GYSLINER PRO 400 GYSLINER COMBI 230 PRO SUMMARY ASSEMBLY des 2 COMPOSITION eee ew er a dor v X v ie 3 STRAIGTHENING LEVER AND 5 4 47 2 2 2 4 2 2 1 1 1 1 3 Choose your bar or your lever 4 4 6 nett nnn 3 Choose the right straightening process sssssssssssrsssrrrssrrnurrnnnrrnnnrrrnnernns 4 Examples of application 6 MAGNETIC EARTH ever et est ette et ve sed ust nete V puente ot oui CER i 6 MANUS POST J esc cte e etal De t UE 6 Connections of the different 016 0 0005 6 Universal dent pulling 41 6 mmn 7 Pulling handles 8 Contact shrinking tool diee et Od aa cleus Lele ete tena 8 EASY GUM mE 8 TRE UR E TR NER CER ERE ea rede 8 V7 190914 No contractual illustrations ASSEMBLY 16 M8x16 16 M8 12 M8x16 12 M8 16 M6x20 4 M6x10 4 M8x45 23 M8x16 20 M6 26 M8 4 M8 6 M6x1
3. n AVV VV VAI Wavy wire x50 ref 049727 To straighten all the To straighten light and middle bumps middle to big bumps bumps Advantages Versatility Fast set up Pulling strength Ideal for rounded areas Ideal for sills example wheel arch Disadvantages Standard space between welded points To be used with Traction rod hooks 4 Hooks 4 6 8 claws Possible tools Lever Lever Straightening bar Straightening bar Pulling bar Pulling bar Straight rings Twisted rings X100 ref 050648 X50 ref 050631 To straighten a flat or To pull in the plane of the edge rounded surface Advice It is possible to weld the rings at a slight angle and to manually position them vertically afterwards When the straightening is finished twisting the rings will enable to easily remove them To weld the wavy wire use wavy wire accessory welder for Manuspot page 6 To unweld the wavy wire use pliers to move the wire sideways until the weld breaks off Note the rings or wavy wires can be reused and should only be replaced if worn out 5 8 APPLICATION EXAMPLES MAGNETIC EARTH Principle and Application This system welded earth system allows to fix an earth on a small stripped part less than 2mm against 20mm with a standard earth Its magnets allows you to use it in ever
4. te the spikes created by the dent pulling operations 1Y 2 ao Du 9 Contact pressure Programmed heating Automatic stop EASY GUN Connect the Manuliner contact clamp to the unit Install the tool at the end of the Easy gun then connect the Manuliner contact clamp to the Easy Gun Weld The welding point is made automatically by a simple contact between the tool and the metal piece to straighten e MINI PULLER ref 051003 alu hook 1 ref 050938 alu hook 2 ref 050945 1 Weld the studs to the aluminium sheet with the Combi 230 Pro 2 Fix the hooks on the studs 3 Pull the hooks with the Mini Puller diagram ne pq X Kw KD RR 8 8 1
5. y position horizontal or vertical ih Weld the earth thanks to Screw the earth to the metal sheet contact shrinking tool p8 MANUSPOT er 050679 Manuspot Complete concept including 1 universal dent pulling clamp 1 pulling handle 2 accessory welder tools wavy 2 rings 1 contact shrinking tool contact clamp with 3m cable copper grease tube ref 050440 1 Easy Gun 6 8 CONNECTION OF DIFERENT TOOLS Connect the contact clamp as follows CC rth yt i ee Connect to the Add copper grease on the Fit the clamp on the generator inside of the clamp and on tool the axis of the tool II UNIVERSAL DENT PULLING CLAMP Principle Adjustment and positioning of the pads Unscrew the nuts on both sides e Then choose the position of the pads depending on the area to work on lt gt lt gt NK E E c GM Weld the tip Tighten the handle to dent Twist the handle to unweld pull the tip Consumables 3 electrodes for Manuspot handles 050822 7 8 PULLING HANDLES 1 T 2m 3 6 Jem E t H Weld the tip Pull back the eTwist the handle to hammer to dent pull unweld the tip Consommable 5 lectrodes de tirage ref 050839 CONTACT SHRINKING TOOL Essential tool for the finishing enables to elimina
Download Pdf Manuals
Related Search