User Manual
Contents
1. Removal of air from the mattress can be facilitated by using the inflation deflation pump connected to the CPR OPEN position The compressor can be put inside the bag in the rolled mattress The following label identifies the cleanliness of the AXTAIR device Slide it into the window on the outer side of the bag QKTQI IX z Blue label when the mattress is clean Yellow label when the mattress is dirty 40 C Temperature conditions mini 10 C or 14 F maxi 40 C or 104 F 104 F 95 Hydrometry level conditions mini 30 maxi 95 3 10 C AAA 30 14 Keep devices away from humidity direct sunlight heat Prevent the risk of shock or alteration by spiky or sharp objects O DISPOSAL OF MEDICAL DEVICE PROTECTION OF THE ENVIRONMENT This device contains several recyclable materials X This symbol shows that this equipment is recyclable and that used devices must not be mixed with other waste Recycling of devices will therefore be done under the best safety conditions to limit the effects on the environment and E human health in the event of the existence of dangerous substances in accordance with the European directive 2002 96 CE for obsolete electrical and electronic equipment You can contact the shop retailer or distributor from whom the product was purchased to find out about collection points for used devices closest to you Before disposal the device should be cleaned in accordance with the MAI2. use in all facilities including domestic ones Pressure fluctuations Flickering 6 a Compliant and those directly connected to low voltage public electricity network CEI 61000 3 3 supplying domestic premises 12 ASKL SANT AXTAIR Electromagnetic immunity Immunity test Test level CEI 60601 Level of compliance Electromagnetic environment Directives Electrostatic discharge eono Floors should be wooden concrete or ceramic tiles If CEI 61000 25 8 kv in air P Dar floors are covered in synthetic materials the relative a B humidity should be at least 30 2 kv AC or DL supply input The quality of the electrical supply network must be that kv signal line and of a typical commercial or hospital environment interconnection 2 kv for electrical supply lines kv for input output lines kv between phases 2 kv between phases and earth lt 5 UT gt 95 weak UT Weak voltage brief for 0 5 cycle 40 UT 0 residual voltage over 0 5 power cuts and voltage 60 weak UT for 5 cycles period variations on electricity 70 UT 30 weak UT for 40 residual voltage for 5 supply lines CEI 61000 4 25 cycles periods lt 5 UT gt 95 weak UT 70 residual voltage for 5s kv in differential mode The quality of the electrical supply network must be that 2 kv in common mode of a typical commercial or hospital environment Transitory excess voltage CEI 61000 4 5 The
3. NTENANCE DISINFECTION instructions to avoid any risk of contamination Thank you for helping to protect the environment P WARRANTY The mattress has a 2 year guarantee except for the cover and foam base and the compressor from the receipt of the purchased good The warranty covers faults or hidden defects and the non compliance of the supplied product The warranty does not apply to the compressor if the seals under the instruction label are removed and or in the event of improper use of the product or non compliance with maintenance recommendations To benefit from it the invoice for the product purchase must be kept Contact your distributor or pharmacist In the event of removal of guarantee seal ASKLE could refuse to cover repair and authorise the right to end this The cover and foam base are guaranteed for year ASKLESANTE AXTAIR Q ELECTROMAGNETIC DATA Axtair One is designed for use in the electromagnetic environment specified below The customer or user of the Axtair One should ensure that it is used in such an environment Emissions test Conformit Electromagnetic environment Directives RE emissions The Axtair One uses RF energy only for internal operations Consequently CISPR group its RF emissions are very low and are not likely to cause interference to a nearby electronic device RF emissions B CISPR du Harmonic emissions class B CEI 61000 3 2 5 The Axtair One is suitable for
4. User Manual ASKLESANTE aKLAIF ONE Pap TE w male be 11111 afaQ PA0010117 150 13485 3nte Medir al MAJ 23 10 2014 UK ASKLESANTE AXTAIR A GENERA D ARR RTS ART Re AR Re TURTON TT IVE AUR en AUTO 2 B RAGCKAGECGONTENTS EK KK 3 C PICTURE LEGEND Siiani aens e eieaa RS RS At 3 D DESCRIP TIO IN 865 3 METHOD OF OPERATION sauts us attrait ut 3 F INDICATIONS SAT RARE AL SSSR EL ni eee 4 G CONTRAINDICATIONS LE 6 4 H RKECAUILIGONS AA 4 l DESCRIPTION aeaiaioe i AR SAR 5 J AXTAIR ONE CONTROL PANEL rennes 6 K INSTALLATION POSE si usa ann Ra Rte L ALARM SUISSE I a A Nr ne dc 8 M MAINTENANCE DISINFECTION 9 N STORAGE LANTA Le AR ARR TR TR R Net Net 11 O DISPOSAL OF MEDICAL DEVICE suis aus Il F WARRANT NNN AN Il Q ELECTROMAGNETIC DA 12 A GENERAL IMPORTANT INFORMATION FOR PATIENTS AND THEIR FAMILIES This product helps to prevent and treat bedsores Why have you been prescribed this Your condi
5. ation relevant to MAINTENANCE STAFF to carry out authorised repairs in accordance with the contract that binds the requester to the ASKLESANTE manufacturer Recommended maintenance and disinfection schema wol ASKLESANTE AXTAIR Receipt Complete device Pre treatment of surface Decontamination Distribution of surface by ufibres Alcohol based solution EPI hygiene mask gloves apron Altered cover Disposal by waste channel Replacement cover Physical property identical to original protective Unacceptable cover YES Biocleaning surface maintenance Method 3 Steps Product Detergent Disinfectant EPI gloves apron Machine wash cover at 90 C Detergent Mattress and compressor Quality Control Compliant Controllo Qualita Product Conforme expertise Materasso e Compressore YES Assemble Record Surface spray Detergent Disinfectant EPI hygiene mask Product release Packaging Broad spectrum alcohol based disinfectant cleaner standardised bactericide ENI040 EN13727 Fungicide ENI275 EN13624 NF 172 190 Sporicide EN13697 EN14561 Polyvirus EN14476 HBV HCV Limit spraying onto cells Detergent Disinfectant for maintenance of floors and surfaces Positive list of Disinfectants Neutral detergent domestic washing product 10 ASKLESANTE AXTAIR N STORAGE A bag is provided for transport and storage of the mattress which must be rolled
6. cept for a cover for the bed support clothing and potentially a complete change Wear loose cotton clothing preferably and if possible with no closures around the pressure area Do not insert folded towels or sheets cushions etc Ensure there are no foreign objects such as piping crumbs etc For hygiene reasons each bedsore preventive aid must be for one person only eo ASKLESANTE AXTAIR B PACKAGE CONTENTS rolled mattress in a carrier bag pump located inside the rolled mattress electrical cable user manual Dirty Clean label C PICTURE LEGENDS Warning electrical and electronic equipment with collective waste collection BF type electrical device Protect against electrocution Complies with requirements of European directive 93 42 CEE applicable to medical devices Alternative current Risk related to electrical current D DESCRIPTION The mattress has 18 air cells that are 12 cm high on a 5 cm foam base The mattress is connected to a pump that blows filtered air at an inflation pressure set according to the patient weight and according to his her position in the bed The cells are interconnected and have 2 networks inflated alternately i e one out of two The whole thing is protected by an integral removable waterproof breathable cover E METHOD OF OPERATION e Alternating pressure avoids prolonged vascular compression likely to cause tissue hypoxia e Pressure adjustment means that t
7. g mode cell out of 2 Cycle time 6 minutes Inflation pressure adjustment depending on the patient s position Mattress inflation time less than 30 minutes or less than 2 minutes with the rapid VKIT AXT inflater Removable anti particle filter Acoustic power lt 35 dBA according to NF EN ISO 3744 1995 Electricity supply 230V 50Hz Electrical cable length 4 2 m Average power consumption 8 Watts Max power 10 VA Fuse T0 63A L35A 250V 5x20 Class Il electric shock protection Electrical and Electro Magnetic conformity according to CEI 60601 1 2005 and 60601 1 2 2007 Legal guarantee 2 years Life span 3 years Pump traceability the number on the back of the pump is a unique identification number PUMP DESCRIPTION indicative values Max flow gt 7 litres min Pmax gt 150 mBar ASKLESANTE AXTAIR J AXTAIR ONE CONTROL PANEL Ce ASKLESANTE www askle com Power indicator light This orange light which is permanently displayed shows that the pump is connected to electricity electric energy source even if the pump is not switched on Pressure adjustment potentiometer This potentiometer adjusts the internal pressure of the mattress cells Its notching principle ensures that the selection is maintained regardless of circumstances touch vibration etc ASKLESANTE AXTAIR K INSTALLATION USE I Unroll the mattress on the bed base according to the in
8. he mattress can be adapted to the patient s morphology and his her position ASKL SANT AXTAIR F INDICATIONS Prevention of bedsores in pressure areas for individuals confined to bed for more than 15 hours with a moderate to high risk of bedsore s assessed according to a validated clinical scale Bedsore treatment aid for stage to stage 2 bedsores in pressure areas with medical advice According to opinion of National Medical Devices Evaluation Commission Ex CEPP published in JORF on 21 July 2005 amended in July 2006 and in accordance with clinical expert opinions G CONTRAINDICATIONS Patients over 110 kg Use as hyperbaric chamber Use on stretcher H PRECAUTIONS Unstable bone injuries and or muscle injuries in contact with the support Cervical pain combined with strict bed confinement Initial post surgery days for bedsore skin graft or strips Patient treated at home unable to have medical assistance or a third person Bed confined individuals with thoracic abdominal corset Individuals requiring continuous posture combining chest levator over 40 and lower limb levator over 20 Behavioural changes in person being treated mood disorder discomfort etc Use of direct physical supports on strict medical prescription re assessed every 24 hours by following the following methods Inflate the mattress using the rapid inflater for a firm surface or adjust the potentiometer to weight 10 kg 2 Attach the co
9. in lying down position e Example 2 For a 10 kg patient adjust the setting according to the person s position a gai on lt 45 Semi sitting position gt 45 3 5 29 CE The pump s instructions for use are written on the right side of it A The weight scale is indicative Check there is no scraping and increase the pressure by one notch if required For comfort inflation can also be adjusted up or down The electrical cable must be installed in such a way as to avoid any interference with articulated parts the wheels of the bed the use of the hoist and staff moving around the bed The mains plug the pneumatic connector and the CPR valve must be permanently visible and accessible When working on the fuse the electricity cable must be disconnected from the pump ASKLESANTE AXTAIR L ALARM In the event of an electrical failure alarm the power light goes off I Check that the compressor is still connected to the pump and or to the socket and or that the general electricity circuit is compliant and that the power light is on 2 If the problem continues we strongly recommend that you disconnect the air pipes from the compressor block them with the transport cap and regularly move the patient change position every 2 to 3 hours 3 Should the device stop working contact your retailer Note correcting the fault results in the power light coming back on Should the mattres
10. nnections to the fixed bed base 3 Select the corresponding weight for the person by turning the potentiometer 4 Check the pressure of support connections several times a day WARNING In accordance with appendix of directive 93 42 CEE covering essential requirements applicable to medical devices only compatibility between systems assembled by ASKL SANT guarantees safe assembly for the use of the AXTAIR motorised air mattress e The description and performance of the motorised air support will be exclusively maintained by the use of the AXTAIR ONE pump ref VAXT POMPE ONE or VAXT2 POMPE ONE combined with the AXTAIR ONE mattress ref VAXT MA ONE or VAXT2 MA ONE and optional inflation deflation kit ref VKIT AXT The national health authority can take appropriate steps at any time to check the marketing conditions for products and take the necessary steps in the event of danger or non compliance with regulations Should the usage requirements listed above not be complied with the user s responsibility is likely to be at cause in the event of an accident e The Axtair One pump is a pressurized device AP generating pressure whose level presents no risk to users and the equipment The Axtair One pump is a device in permanent operation In the event of an emergency it can be switched off by unplugging the cable from its base Only accredited and competent staff can repair or interfere with the inside of the device on condition tha
11. of 150 kHz at 80 MHz 80 MHz at 800 MHz of 800 MHz at 2 5 GHz d 3 5 VI d 3 5 E1 JP d 7 EI For emitters whose assigned maximum emission power is not given above the recommended separation distance d in metres m can be estimated by using the equation applicable to the frequency of the emitter in watts W according to the manufacturer of the latter NOTE At 80 MHz and 800 MHz the separation distance for the highest frequencies range applies NOTE 2 These directives may not apply in all situations The electromagnetic propagation is affected by absorption and by reflection of structures objects and people 14 ASKLESANTE AXTAIR ASKLESANTE Avec Ecofolio papiers tous les papiers se recyclent ASKL SANT groupe Winncare 200 rue Charles Tellier Actiparc de Gr zan 30 034 N mes Cedex 1 France T l 33 0 4 66 02 15 15 Fax 33 0 4 66 02 15 Email contact askle com www winncare fr
12. quality of the electrical supply network must be that of a typical commercial or hospital environment The magnetic fields at the frequency of the electricity network should have the levels characteristic of a representative site located in a typical commercial or hospital environment Magnetic field at frequency of electricity 3 A m at 50 Hz network 50 60 Hz CEI 61000 4 8 Portable and mobile RF communication devices must not be used near any part of an Axtair One including cables that of the recommended separation distance calculated from the equation applicable to the emitting frequency Recommended separation distance d 3 5 VI RF disturbances CEI d 3 5 El VP 80 MHz at 800 MHz 61000 4 6 pO NEM OF SR AI2860 d 7 El VP 800 MHz at 2 5 GHz MHz oh Radiated RF disturbances 3V m of 80 mHz at 2 5 GHz Where P is the maximum output power of the emitting CEI 61000 4 3 device in watts W according to the manufacturer of the emitting device and d is the recommended separation distance in metres m The field intensities of fixed RF emitters determined by an electromagnetic test on site should be lower than the conformity level in each range of frequencies NOTE UT is the voltage of the alternative network before the test level is applied NOTE 2 At 80 MHz and at 800 MHz the highest frequency range applies NOTE 3 These directives may not apply in all situations The electromagnetic propagation is affected b
13. s be accidentally deflated when re inflating check that the patient s limb is not stuck between the mattress and the bed barriers CPR Emergency Cardio Pulmonary Resuscitation In the event of a heart attack I Turn the nozzle of the CPR valve to position the plastic tube to the OPEN position 2 The mattress deflates and the lower part of the thorax can be found in less than 15 seconds on the firm side of the bed base to enable External Cardiac Massage A The mains plug the pneumatic connector and the CPR valve must be permanently visible and accessible ASKLESANTE AXTAIR M MAINTENANCE DISINFECTION The method used depends on the level of disinfection required Techniques and products will be used according to validated good practice recommendations See the diagram at the end of this section J Daily maintenance of the compressor is done when it is switched on and with the mattress connected to the connector By default the electrical cable connected to the compressor must be unplugged The orange light must be off Do not use a high pressure jet to clean an Axtair One compressor Do not put the compressor on bare ground Hang it 2 60 cm away from a water point A Prohibit the use of corrosive cleaning products such as industrial spot removers acetone solvents ether and colorant products iodized alcohol potassium permanganate silver nitrate etc Prohibit abrasive materials such as steel wool or scotch bri
14. structions given by the head and foot symbols printed on the surface of the cover 2 Hang the pump on the bed panel feet side using the brackets and attach them 3 Guide the cable for the pump to the nearest plug socket and plug it in The orange light comes on and the pump starts automatically Recommendation Use the optional ASKLE SANTE rapid inflation pump Connect the electrical cable for the inflation pump to the electricity Block the electricity cable for the mattress with the adjoining cap Turn the CPR valve to OPEN Connect the rapid inflation pump as per the diagram opposite Note the pump inflates in one direction and deflates in the other Press and hold the on button until the mattress is inflated approx 2 minutes Turn the CPR valve of the mattress to the CLOSE position Connect the electricity cable for the mattress to the pump connector Lie the patient down on the mattress if you think it is sufficiently inflated Adjust the inflation pressure for the mattress to the weight of the patient using the weight scale ae di Adjustment of pressure for semi sitting position i e incline of chest levator of bed gt 45 To avoid the risk of pressure of buttock areas on the foam mattress in semi sitting position the internal pressure of cells must be increased We recommend increasing the pressure by notch Example I A 50 kg patient in sitting position would need a pressure equivalent to a 60 kg patient
15. t the cable is disconnected from the electricity network e The Axtair mattress is placed directly on the medical bed base Use under an overmattress is the sole responsibility of the installer Usage temperatures must be between 10 C and 40 C The product must not be used at altitudes over 2000 m The device must be used in an electromagnetic environment in which radiated RF disturbances are controlled see section Q ASKL SANT AXTAIR l DESCRIPTION SUPPORT DESCRIPTION Validated user weight 30 I 10 kg Support weight 5 7 Kg Support size VAXT MA ONE 195 x 85 x 17 cm VAXT2 MA ONE 195 x 87 x 17 cm Height of air cells 12 cm Rapid CPR deflation in less than 15 seconds Cell material Ether polyurethane 300 um Polyether 18 kg m3 foam base optional cover with a PROMUST PU cover Upper section of cover PROMUST PU Jersey Polyurethane ptional Promust CIC Lower section of cover PU PVC non slip polyurethane Vinyl polychloride Standby with transport cap gt 8 hours Compliance with inflammability tests according to EN 597 182 1995 GPEM D 1 90 amp DI 89bis Cover and foam base guarantee year does not replace legal guarantee Promust CIC cover guarantee 2 years Life span 5 years not cover Compatible with the rapid VKIT AXT inflation pump Mattress traceability The date written on the label of the mattress cover is the date of mattress manufacture PUMP DEVICE DESCRIPTION Alternatin
16. te The filter should be changed time per year or more frequently depending on environmental conditions dust smoke Compressor Use a microfibre dish cloth soaked in a surface detergent disinfectant at the manufacturer s recommended concentrations Comply with application time The filter must be changed at least every 6 months or more frequently depending on environmental conditions dust smoke etc Mattress Use a microfibre dish cloth soaked in a surface detergent or Detergent Disinfectant at the manufacturer s recommended concentrations Rinse Use a surface Detergent Disinfectant product Comply with application time CE marking obligatory under terms of directive 93 42 CEE for products claiming use on surfaces of Medical Devices Use products that comply with biocide directive Maintenance recommendations for the cover and base 567 Wash in water max temp 90 C reduced mechanical action rinsing in decreasing temperature reduced wringing out 5000 ppm chlorine authorised 1000 ppm in standard use 5000 pom x Ironing forbidden ed Dry cleaning forbidden use of solvent based stain remover forbidden Drum drying authorised moderate temperatures Item treated with a biocidal substance that is safe for the user www winncare fr The MANUFACTURER will make available upon request the circuit schemas list of components descriptions calibration instructions or any other inform
17. tion reduces your mobility and exposes you to the risk of bedsores What is a bedsore A bedsore is a lesion on the skin which can be deep or shallow and is caused by excessive and prolonged compression of tissue between the body and a support This excessive pressure can stop blood circulation and cause bedsores There are several types of bedsore simple redness lasting longer than a day hardening of the skin or a deep or shallow wound which in serious cases can affect muscles or underlying bone A bedsore may be related to reduced mobility and or a chronic disease How does this support work This support reduces pressure and allows better blood circulation in skin thereby helping to prevent bedsores Directions and precautions for use A support is not enough in itself to prevent bedsores other preventive steps are also required change position frequently at least every 2 to 3 hours keep skin clean and avoid soaking if incontinent replace protection regularly check skin condition daily or have someone else check it have a proper diet drink regularly and sufficiently If any of these steps cannot be followed you must inform your doctor or nurse as early as possible Report any abnormal events to your doctor or nurse such as fever pain or redness or whitening of pressure points head shoulder back hip shoulder blade pelvis heel etc It is important not to have too much thickness between the body and the support ex
18. y absorption and by reflection of structures objects and people The field intensities of fixed emitters such as base stations for radiotelephones cellular cordless and terrestrial mobile radios amateur radio AM and FM radio and TV cannot be theoretically planned with accuracy To evaluate the electromagnetic environment due to fixed RF emitters an electromagnetic test should be considered on this site If the field intensity measured at the location where the Axtair One is used exceeds the applicable RF conformity level below the Axtair One should be monitored to check that it is working normally If abnormal performance is found additional actions may be required like redirecting or repositioning the Axtair One For the frequency range of 150 KHz at 80 MHz the field intensities should be below VIT V m 13 ASKLESANTE AXTAIR Recommended separation distances between portable and mobile RF communication devices and the Axtair One The Axtair One is planned for use in the electromagnetic field in which radiated RF disturbances are controlled The customer or user of the Axtair One can help to prevent electromagnetic interference by maintaining a minimum distance between portable or mobile RF communication devices emitter and the Axtair One as recommended below according to the maximum emission power of the communication device Maximum output power Separation distance according to frequency of emitter assigned forthe emitter
Download Pdf Manuals
Related Search