KORTEX Kx Router 4G LTE Pro User Manual
Contents
1. WEP Keys caca WEP Keys Select ASCII or Hex from the pull down list to set up the key value ASCII American Standard Code for Information Interchange is a code for representing char as numbers from 0 127 Hexadecimal digits consist of the numbers 0 9 and the letters A F a f 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 se KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX pm PSI O WPA PSK WPA2 PSK Mode WPA Wi Fi Protected Access is the older standard select this option if the clients that will be used with the router only support the older standard WPA2 is the newer implementation of the stronger IEEE 802 11i security standard PSK Pre Shared Key is the key which is entered as a pass phrase of up to 63 alphanumeric characters in ASCII American Standard Code for Information Interchange format or 64 digits in HEX format at both ends of the wireless connection When inputting ASCII strings it cannot be shorter than eight characters although for proper security it needs to be of ample length and should not be a commonly known phrase This phrase is used to generate session keys that are unique for each wireless client Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from unauthorized access and monitoring Select SSID SSID choice betaurtWwiri gt 3Jtech WiFi Security Mode WPA PSK WPA Algorithms C TKIP C AES2. KX Router 4G LTE Pro User Manual V1 1 O KORTEX s o 4 5 9 8 Status In the Status page it tells you the basic information of the system You can check the device status including the firmware version system up time current operation mode WAN Local IP address MAC address and so on They will be refreshed per 3 seconds With these informations it is helpful while malfunctioning FWT AP Status Firmware Version 51 10 00 05 System Up Time 32 mins 12 secs Operation Mode Gateway Mode System Flash Size BMBytes System GSM Modem Name Sierra MC7710 WAN IP Address WAN Subnet Mask WAN Default Gateway Primary Domain Name Server 168 95 1 1 Secondary Domain Name Server 8 8 8 8 4G WAN IP Address 176 178 179 229 4G Subnet Mask 255 255 255 255 46 Default Gateway 10 64 64 64 VPN IP Address VPN Subnet Mask VPN Default Gateway Wifi AP Client IP Address wifi AP Client Subnet Mask wifi AP Client Default Gateway WIFI AP Client Connection Status DISCONNECTED Local IP Address 192 168 8 1 Local Netmask 255 255 255 0 MAC Address 00 09 85 22 95 40 IMEI 3581 78042662579 csa 26 PLMN 20820 Connertion Type CCID 893320951 0000862376F Main Route Status 4c From the Status Windows you can read the various informations after the system is connected 91 rue Reaumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual
3. In Static Routing Settings the user can set up a route rule table here Refer to the description of the following parameters to set up the necessary route rule and click the Apply button when you complete Static Routing Settings You may add and remove custom Internet routing rules Add a routing rule Destination Range Gateway Interface Comment Current Routing table in the system Destination Netmask Gateway Flags Metric Ref Use Interface Comment LAN br0 LAN br0 4 255 255 255 255 255 255 255 255 0 0 0 0 5 0 o O 2 192 168 8 0 255 255 255 0 10000 1 Dynamic Routing Settings Dynamic Routing Protocol 91 rue R aumur 75002 PARIS Tel OI 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s ol Destination The IP address of packets that will take this route Range Includes Host and Net options When selecting Net there is another Netmask column that needs to be filled out Netmask The bits in the mask specify which bits of the IP address must match Gateway The gateway for the routing Interface Specifies the interface LAN or WAN that the IP packet must use to transit out of the router when this route is used Or you can choose the user defined way by selecting the Custom option Comment Memo for the routing rule Routing Table Lists the current route rules you have added before Click on the
4. Pass Phrase 12345678 Key Renewal Interval 3600 seconds 0 4194303 Apply Cancel WPA Algorithms Mark the option to enable modes of TKIP or AES Pass Phrase This mode requires only an access point and client station that supports WPA PSK The WPA PSK settings include Key Format Length and Value They must be as same as each wireless client in your wireless network When Key format is Passphrase the key value should have 8 63 ASCII characters or 64 digits in HEX format Key Renewal Interval Enter a value to set up the WPA key renewal interval The device regenerates the key in every interval seconds that you have setup without disconnection The WPA Algorithm will regroup the key for a period The default value is 3600 seconds and you can adjust the time interval Valid Range 0 4194303 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O AP Client Settings With the AP Client function the KX ROUTER 4G LTE PRO could connect to other remote Wi Fi AP AP1 as a Wi Fi station and it will be bridged with KORTEX router Wi Fi AP and LAN which means that PC Wi Fi clients under AP1 and PCs clients under KX ROUTER 4G LTE PRO LAN and Wi Fi could communicate with each other Just fill in the network name SSID and the pass phrase security key of the Wi Fi AP that KORTEX router would like to connect Please note that the setup of Network Mode as well as
5. create When using WEP you must determine the level of encryption The type of encryption determines the key length 128 bit encryption requires a longer key than 64 bit encryption Keys are defined by entering in a string in HEX hexadecimal using characters 0 9 A F a f or ASCII American Standard Code for Information Interchange alphanumeric characters format ASCII format is provided so you can enter a string that is easier to remember The ASCII string is converted to HEX for use over the network 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s om Examples 64 bit hexadecimal keys are exactly 10 characters in length 12345678FA is a valid string of 10 characters for 64 bit encryption 128 bit hexadecimal keys are exactly 26 characters in length 456FBCDF 1234001 22225271730 is a valid string of 26 characters for 128 bit encryption 64 bit ASCII keys are up to 5 characters in length DMODE is a valid string of 5 characters for 64 bit encryption 128 bit ASCII keys are up to 13 characters in length 2002HALOSWIN1 is a valid string of 13 characters for 128 bit encryption Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from unauthorized access and monitoring Select SSID sSID choice DetauitWiFi 3Jtech WiFi Security Mode WEPAUTO y Wire Equivalence Protection WEP
6. server as well as Time Zone the router will sync the time immediately after pressing the Apply button NTP Synchronization hours Though it synchronizes the time automatically NTP does not update the time periodically without user s processing You can set up the time interval Valid range 1 300 hours to have the assigned NTP server do the synchronization of time for your router DDNS Dynamic DNS Settings The Dynamic DNS feature allows you to host a server Web FTP Game Server etc using a domain name that you have registered www dyndns com or www no ip com with your dynamically assigned IP address Most broadband Internet Service Providers assign dynamic changing IP addresses When you use a Dynamic DNS service provider your friends can enter your domain name to connect to your server no matter what your IP address is Dynamic DNS Provider Select a dynamic DNS service provider from the pull down list Account Enter the username or key provided by your service provider Password Enter the password or key provided by your service provider DDNS Enter the hostname you have registered Note After configuring the router for dynamic DNS you can open a browser and navigate to the URL for your domain for example http www mydomain info and KX ROUTER 4G LTE PRO will attempt to forward the request to port 80 on your LAN 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User
7. Delete button to delete the selected route rule 4 3 6 2 Add a routing rule This page is about how to set static routing function of the router Destination please enter Target Host or IP network segment Range Host or Network can be chosen Gateway IP address of the next router Interface You can choose the corresponding interface type Comment some notes Notice gt Gateway and LAN IP of this router must belong to the same network segment gt Ifthe destination IP address is the one of a host and then the Subnet Mask must be 255 255 255 255 gt Ifthe destination IP address is IP network segment it must match with the Subnet Mask For example if the destination IP is 10 0 0 0 and the Subnet Mask is 255 0 0 0 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX PSI O 4 5 7 Wireless settings 4 5 7 1 Basic Wireless Settings The wireless section is used to configure the wireless settings for your Company router Please note that changes made on this section may also need to be duplicated on your Wireless Client To protect your privacy use the wireless security mode to configure the wireless security features This device supports three wireless security modes including WEP WPA PSK and WPA2 PSK WEP is the original wireless encryption standard WPA provides a higher level of security WPA PSK does not require an authentication server The WPA2 PSK
8. Frequency Channel No for the KX ROUTER 4G LTE PRO in the Wireless Settings gt Basic setting page must match the values used on this Wi Fi AP AP Client Feature You could configure AP Client parameters here AP Client Parameters SSID KORTEX 4G LTE PRO MAC Address Optional Security Mode wPA2PSK gt Encryption Type AES Pass Phrase 12345678 Auto Select WIFI channel for FlashAir Disable Apply Cancel 4 5 7 3 Station List From the list of Station you can see which devices are currently connecting to your KX ROUTER 4G LTE PRO in the wireless way through the MAC address You also can have a clear realization of status including Aid PSM MimoPS MCS BW Bandwidth SGI and STBC for each Wi Fi connection Station List You could monitor stations which associated to this AP here ae usss D fh 91 rue R aumur 75002 PARIS Tel OI 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX in PSI O 4 5 7 4 Statistics The KX ROUTER 4G LTE PRO offers the counter function to collect all wireless traffic counting information about the transmitting receiving packets of this router The system will automatically update these wireless data per 3 seconds To restart the counting please click on the Reset Counters button AP Wireless Statistics Wireless TX and RX statistics Transmit Statistics Tx Success 0 Tx Retry Count 0 PER 0 0 Tx Fail after retry 0 PLR 0
9. KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 RTEX rs 4 5 Configure Parameters 4 5 1 Internet Settings 192 168 8 1 home asp or KORTEX2s 4 Home 3 Internet Settings Q wan L LAN O DHCP clients L VPN C Advanced Routing 3 Wireless Settings D Basic Q Security L AP Client Station List L Statistics J Firewall L MAC IP Port Filtering C Port Forwarding C omz C System Security Management System SIM TRO69 Firmware Configuration Status Statistics System Log DEODODODO PRODUCTS amp SERVICES MACHINE TO MACHINE POINT OF SALES POS ENERGY EFFICIENCY KX ROUTER 4G LTE PRO FWT AP Status Firmware Version 51 10 00 05 18 mins 43 secs System Up Time Operation Mode System Flash Size BMBytes System GSM Modem Name Sierra MC7710 WAN IP Address WAN Subnet Mask WAN Default Gateway Primary Domain Name Server Gateway Mode 168 95 1 1 Secondary Domain Name Server 8 8 8 8 4G WAN IP Address 1 76 178 179 229 4G Subnet Mask 255 255 255 255 4G Default Gateway 1 0 64 64 64 VPN IP Address VPN Subnet Mask VPN Default Gateway Wifi AP Client IP Address Wifi AP Client Subnet Mask Wifi AP Client Default Gateway WIFI AP Client Connection Status DISCONNECTED Local IP Address 192 168 8 1 Local Netmask 255 255 255 0 MAC Address 00 09 85
10. ROUTER 4G LTE PRO For more details please refer to the following parameters below SIM Card Status It includes SIM not inserted READY SIM PIN SIM PUK ERROR five statuses SIM not inserted It stands that the SIM card has not been inserted into the router yet READY It stands that the SIM card works normally SIM PIN It stands that the user needs to input the correct PIN code due to the wrong PIN code value of system SIM PUK It stands that the SIM card has already been locked The user needs to request ISP and input the correct PUK to unlock the SIM card ERROR This message will be shown if the system fails to detect the information of the SIM card Remaining attempts to enter PIN It shows the remaining times that you are allowed to input the PIN code for the SIM card inserted into the router Once the times exceeds 3 times the SIM card will be locked Remaining attempts to enter PUK It shows the remaining times that you are allowed to input the PUK for the SIM card inserted into the router Once the times exceeds 10 times the SIM card will be useless 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s i Automatic PIN CODE insertion on boot Decide that whether to use the value filled in the field of Type the PIN CODE for automatic insertion to do the authentication of SIM card or not while the router is powered on To
11. V1 1 O KORTEX o 4 5 9 9 Statistics The KX ROUTER 4G LTE PRO offers the counter function to collect all counting information about the memory status and all interfaces receiving transmitting packets of this router Statistic A Memory total 28052 kB Memory left 7220 KB Name ral Wifi Rx Packet 61 8 Rx Byte 123676 Tx Packet 18 Tx Byte Name eth2 2 WAN Eth Rx Packet lo Rx Byte Tx Packet 201 Tx Byte 119394 Name brO LAN Rx Packet 4748 Rx Byte 389440 Tx Packet 6980 Tx Byte 6778547 Name ppp0 4G Rx Packet 3234 Rx Byte 3966074 Tx Packet 1794 Tx Byte 91850 Display the statistics information of system flow 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O 4 5 9 10 System log System Log Syslog Kortex user info kernel brO port 2 ra0 entering learning state A Kortex user info kernel brO port lieth2 1 entering learning state Kortex user info kernel brO topology change detected propagating Kortex user info kernel brO port 2 ra0 entering forwarding state Kortex user info kernel brO topology change detected propagating Kortex user info kernel brO port lf eth2 1 entering forwarding state Kortex user warn kernel RT305x_ESU Link Status Changed raeth raether c Kortex user warn kernel RT305x ESW Link Status Changed raeth raether c
12. enable it please click on the checkbox in front of this function Enable PIN request for initialization Enable Disable the PIN code function In case this function is enabled and your SIM card has the PIN code setup you must input the correct pin code and press the Apply button for the authentication Three successively incorrect input of Pin Code will make the SIM card locked Enter PIN In case the field of SIM Card Status in the Information Table is at the SIM PIN status you should enter the correct PIN code in the PIN field of this function and press the Apply button for authentication The system will return the message in the pop up window for you to realize whether your setting is successful or not Change PIN Besides the cell phone you are also allowed to modify your PIN code of the SIM card through this function To modify this password please fill in your old password and your desired new password accordingly and then re key this new password into the Confirm New PIN field The new settings will be taken effect immediately after you press the Apply button You also can realize whether this change is successful or not from the message returned by the system in the pop up window PIN Unlock As we had mentioned above the SIM PUK status displayed in the field of SIM Card Status in the Information Table it means that the SIM card is locked To unlock the SIM card you should enter the correct PUK in the PUK field of this f
13. option does require a RADIUS authentication server Through the basic wireless setting page the user can control the ON OFF status of Wi Fi function and set up the 802 11 mode Network Name SSID as well as Channel Besides you can do the further settings related to the HT Physical Mode Basic Wireless Settings You could configure the minimum number of Wireless settings for communication such as Network Name SSID and Channel The Access Point can be set simply with only the minimum setting items Wireless Network Network Mode 1 1b g n mixed mode v Network Name SSID default Hidden Multiple SSID1 Hidden C Multiple SSID2 Hidden Multiple SSID3 Hidden O Broadcast Network Name SSID Enable Disable AP Isolation O Enable Disable MBSSID AP Isolation O Enable Disable Frequency Channel 2437MHz Channel 6 v Operating Mode Mixed Mode Green Field Channel BandWidth O20 20 40 Guard Interval O Long Auto MCS Auto Y Reverse Direction Grant RDG O ia O Enable Extension Channel 2457MHz Channel 10 v Aggregation MSDU A MSDU Disable Enable Auto Block ACK O Disable Enable Decline BA Request Disable O Enable Cor e 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s ol Wireless Network Settings Wi Fi On Off This option turns on and off the wireless connecti
14. option in the back of your desired SSID AP Isolation Enable Disable this function Create a separate virtual network for your wireless network When this feature is enabled each of your wireless clients will be in its own virtual network and will not be able to communicate with each other You may want to utilize this feature if you have many guests that frequent your wireless network MBSSID AP Isolation Enable Disable the MBSSID AP Isolation function The router supports multiple SSIDs You can decide whether the clients associated to different SSIDs on the device can see each other or not Enable the option to block it Default is Disable Frequency Channel A wireless network uses specific channels in the 2 4GHz wireless spectrum to handle communication between clients Some channels in your area may have interference from other electronic devices Choose the clearest channel to help optimize the performance and coverage of your wireless network If you select AutoSelect the router automatically finds the channel with least interference and uses that channel for wireless networking 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX mn PSI O Rate Exist only when selecting 802 11b g mixed mode 802 11b only 802 11g only as the Network Mode for the router You can set up the desired transmitting rate for these network modes Default is Auto HT Physical Mod
15. rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O The table below shows the relationship among Phy data rate Bandwidth and Guard Interval Data Bandwidth 20MHz Rate Short Guard Bandwidth 40 MHz Mbps Interval Long Guard Interval Short Guard Interval Long Guard Interval 72 6 5 15 13 5 144 13 30 27 21 7 19 5 45 405 28 9 26 60 54 43 3 39 90 81 57 8 52 2 108 65 121 5 72 2 65 5 135 144 13 2 28 9 26 54 43 3 39 81 57 8 52 86 7 78 115 6 104 130 144 4 Not Supported par bo A w 5 6 7 7 MCS Modulation Coding Scheme MCS 0 7 1S One Tx Stream MCS 8 15 2S Two Tx Stream MCS 32 BPSK Reverse Direction Grant RDG This is the 11n performance parameter Enable it if needed Extension Channel Exist only when selecting 20 40 as the Channel BandWidth for the router For example if channel 6 is selected it means you can select channel 2 or channel 10 as the extension channel Choose the unused channel as the extension channel Aggregation MSDU A MSDU The multiple HT packets can be transmitted with single ACK reply packet Enable it to apply this function and reduce the network congestion Auto Block ACK It is another aggregation technique which prevents sending ACK in the communication to increase the throughput If this option is enabled the device will activate this function when transmi
16. settings Besides through the press of the RESET button in the front panel to execute the hardware reset function as we had mentioned before for the router The software reset function provided here takes the same effect as the RESET button on the front panel of the router It will take about 30 60 seconds to complete the system boot 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTE X Ps Settings Management You might save system settings by exporting them to a configuration file restore them by importing the file or reset them to factory default Click here to export current configuration Locate import file Factory Defaults Click here to load factory defaults Load Default Export To export the current settings stored in the flash to a config file just press the Export button Import Import the config file into your router Specify the filename and directory where the file is located via the Browse button and press the Import button when completed Load Default Restoring the unit to the factory default settings will erase all settings including any rules that you had created To have the router s settings be returned to the factory default just press the Load Default button Please note that the router cannot be powered off while resetting to the factory default 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI
17. 0e 00 RTS Successfully Receive CTS 0 RTS Fail To Receive CTS 0 Frames Received Successfully 0 Frames Received With CRC Error 0 PER 0 0 SSS E f SNR n a n a n a Reset Counters Tx Success Display the transmitted number of the successful packets Tx Retry Count Display the transmitted number of the retry packets Tx Fail after retry Display the transmitted number of the unsuccessful packets after retry RTS Successfully Receive CTS Display the transmitted number of RTS Request To Send packets which receive CTS Clear To Send packets successfully RTS Fail To Receive CTS Display the transmitted number of RTS Request To Send packets which receive CTS Clear To Send packets unsuccessfully Frames Received Successfully Display the received number of the successful frames Frames Received With CRC Error Display the received number of frames with CRC error packets SNR Signal to Noise ratio SNR It stands that how fast wireless data of the router can travel and how far a wireless signal of the router can reach 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O 4 5 8 Firewall 4 5 8 1 MAC IP Port Filter Settings The router could filter the outgoing packets for security or management consideration You can set up the filter against the IP addresses to block specific internal users from accessing the Internet The firewall could not o
18. 22 95 40 IMEI 3581 78042662579 csa 13 PLMN 20820 Connection Type CCID 893320951 0000862376F Main Route Status 46 el a 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s ol 4 5 2 WAN settings The WAN Wide Area Network section is where you configure your Internet connection type The KX ROUTER 4G LTE PRO supports 4G dialup connection type to access Internet Please contact your Internet Service Provider before configuring the required parameters Wide Area Network WAN Settings WAN Connection Type DHCP Auto config v DHCP Mode Hostname optional 3G Mode APN Dial Number Username Pasword Auth Mode Auto Y Connection Type Automatic Wan Weight WAN1 WAN2 gt WAN Connection Type support Static IP fixed IP DHCP Auto Config PPPOE ADSL DHCP Mode gt Hostname input it optional 3G Mode gt APN Access Point Name This SIM Card APN name is from Mobile Management Service Provider Dial Number Input the Dialing Number you get from ISP Default is 99 Username input it if ISP offers Password input it if ISP offers Auth Mode PAP CHAP Auto Wan Weight gt Wan Weight Default 1 1 Load Balancing if you only use 4G 3G you no need setting or setting 1 1 V y V V 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTE
19. 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 J KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s o Chapter 5 FAQ gt SIM Card Status shows Not Ready It means the SIM card is not found you can take SIM card out and insert it again Signal Strength is normal but can t get WAN IP Check the APN parameters in WAN settings gt Can t visit the router from remote side 1 Make a ping to the WAN IP to check whether it is successful 2 We are using 80 as router s default port but some ISP block the 80 port you can confirm with local ISP which ports are open and change port to try gt LAN fails 1 Check RJ45 cable make sure it is correctly connected 2 Make sure the PC and router are in same network segment 3 Disable the PC network card and re enable it ln Create Shortcut Bridge Connections Create Shortcut Rename Properties Rename Properties 4 Reset the router Press Reset button for several seconds it will load to factory settings gt Get WAN IP but PC can t access internet 1 Check the DNS you can make a ping to a normal IP e g 8 8 8 8 if ping IP is ok the question must be caused by DNS 2 Make sure the SIM card support data service you can try it in your cell phone 3 Signal is too weak Move antenna or change position to get better signal 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1
20. Enter button in your computer keyboard gt Type User Name admin and Password admin in the pop up Login Window and then press the OK button 21x Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name Es admin Y Password ose V Remember my password ce 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 X PSI KX Router 4G LTE Pro L 4 3 Front LEDs 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX4s o Meaning LED 1 Lit when power is ON Lit when a SMS is received Used for remote monitoring MAIL Lit when the Wi Fi function is enabled WLAN Flash when the data is transmitting Off when the Wi Fi function is disabled default LAN port 1 Lit when the cable connection with device exists Flash when the data is transmitting Off when no cable connection exists LAN port 2 Lit when the cable connection with device exists Flash when the data is transmitting Off when no cable connection exists LAN port 3 Lit when the cable connection with device exists Flash when the data is transmitting Off when no cable connection exists LAN port 4 Lit when the cable connection with device exists Flash when the data is transmitting Off when no cable connection exists w Lit when connect
21. G LTE Pro User Manual V1 1 O KORTEX s mes Chapter 1 Introduction Here to introduce the KX ROUTER 4G LTE PRO it will be much helpful during your application 1 Purpose 2 Application range 3 Version 4 Technical support 1 1 Purpose The user manual will be used for your installation and test 1 2 Application range This manual is intended for persons with certain computer networks and electronic technical knowledge network administrators and other related equipment managers who need to use the 4g router 1 3 Edition According to the market and the needs of users the router products will make adjustments on related features and technical improvements The following table explains product specifications and amendments in the revised version of the reasons described in different periods Version No Amendment Participation Date Details V1 0 R amp D Market Technical Dep 2013 12 First Version V1 1 R amp D Market Technical Dep 2015 03 Second Version 1 4 Technical support To enable users to quickly solve problems encountered in the course and get the right solution on hardware operating system and installation please contact customer service staff France 0820 69 00 42 International 33134043760 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O o O KORTEX s O Chapter 2 Product specification 2 1 Overview With the development o
22. KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s ol KORTEX Kx Router 4G LTE Pro User Manual KORTEXA 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX4s oi Content CHAPTER 1 INTRODUCTION 4 PURPOSES e ii ere ene 4 2 APPLICATIONIRANGE u ul u un S abans e dees ae 4 LS DITO Nees o o cines su sua s asa usss ns 4 1 4 TECHNICAL SUPPOR Tecos ralla iii 4 CHAPTER 2 PRODUCT SPECIFICATION 5 BAN OVER VIEN ci a a a aus 5 2 2 SPECIEIGATION aan eno oo het oo 6 CHAPTER 3 INSTALLATIOLN 7 3 ACCESSORIE Sk S let o lea in dio el o a 8 3 2 INSTALLATION Essen ne td iaa 8 CHAPTER 4 CONFIGURE isvsccstiscsisssscosecenseoosoveaseczoressesosassnscessessvonssansuncaiosondcensnsvasbodsoadesssesensesostoesasiesess 9 q AS OVERVIEW exccccessoest casts sds cus muu asan latas asta 9 4 2 CONNECTION ss ne dt men mn nn it in ni ie en nn 9 4 2 1 Computer network configuration 9 4 2 2 Login the router ss 10 4 39 FRONT LEDS voi tie ees Heads ee a en rite 11 4A REAR PANEL ocioso S r E Ee a aE E EE ea E O AE EER 13 4 5 CONFIGURE PARAMETERS LLULLU iia til ita 14 4 5 1 In
23. Kortex user info kernel brO port 2 ra0 entering disabled state Kortex user warn kernel switch register base addr to Oxb0180000 Kortex user warn kernel write offset Ox400 value 0x1080 Kortex user warn kernel write offset 0x1204 value 0x8 Kortex user warn kernel write offset 0x1004 value 0x3 Kortex daemon notice pppd 3410 pppd 2 4 2 started by admin uid 0 Kortex daemon info pppd 3410 Serial connection established Kortex daemon debug pppd 3410 using channel 1 Kortex daemon info pppd 3410 Using interface ppp0 Kortex daemon notice pppd 3410 Connect ppp0 lt gt dev ttyUSB4 Kortex daemon debug pppd 3410 sent LCP ConfReq id 0x1 lt asyncmap 0x0 gt lt magic Kortex daemon debug pppd 3410 rcvd LCP ConfReq id 0x0 lt asyncmap 0x0 gt lt auth Kortex daemon debug pppd 3410 sent LCP ConfRej id 0x0 lt pcomp gt lt accomp gt Kortex daemon debug pppd 3410 rcvd LCP Conf ck id 0x1 lt asyncmap 0x0 gt lt magic Kortex daemon debug pppd 3410 rcvd LCP ConfReg id 0x1 lt asyncmap 0x0 gt lt auth Kortex daemon debug pppd 3410 sent LCP Conf ck id 0xl lt asyncmap 0x0 gt lt auth Kortex daemon debug pppd 3410 rcvd LCP DiscReg id 0x2 magic 0xbe763873 Kortex daemon debug pppd 3410 rcvd CHAP Challenge id 0x 1 lt 6810f2 2729813 28t Kortex daemon debug pppd 3410 sent CHAP Response id 0x1 lt 16baf6539630laaa72t Kortex daemon debug pppd 3410 rcvd CHAP Success id 0x1 Kortex daemon i
24. Manual V1 1 O KORTEX s O 4 5 9 2 SIM On this SIM Card Control settings page you can set up the password for SIM card s authentication The KX ROUTER 4G LTE PRO will detect automatically the current limit times of PIN code and PUK input for your SIM card If the remaining times of PIN code input are less than 3 times the system will stop all related functions You should configure the PIN code of the SIM card on this web setting page and enter the correct PIN code again before the reboot of the device Note 1 The wrong input of PIN code and PUK in the following setup will decrease the allowable input times of PIN code and PUK Note 2 Any changes on this webpage the user needs to reset to power to have all related functions work normally Information SIM Card Status READY Remaining attempts to enter PIN 3 Pemaining attempts to enter PUK 10 Automatic PIN CODE insertion on boot Type the PIN CODE for automatic insertion Apply Cancel Enable PIN request for inicialization Enable No x PIN Co Apply Cancel 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX PSI O Enter PIN PIN Cancel Change PIN Old PIN New PIN Confirm New PIN Apply Cancel PIN Uniock Information Table This table will show all information about the SIM card used in your KX
25. O KORTEX s o gt Port forwarding not working 1 Check with ISP which ports are open by them 2 More than 1 router The most common problem we come across is people who are behind 2 or more routers and don t realize it So here is a quick step by step Step 1 Login into your Router Step 2 Find the status page that shows the WAN Internet IP address and write it down Step 3 Log into the first router modem now Step 4 Find the DMZ page Step 5 Enter the IP you wrote down into the DMZ page and enable DMZ Step 6 Save and your done Thankfully it is easy to get port forwarding if this is happening We simply tell the first router to send all incoming connections to the 2nd router where the port forwarding rules are 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62
26. PI SPI Firewall Remote management via WAN Allow or Not Allow the user to log in the system with the WAN IP Ping from WAN Filter Enable Disable the function of Ping from WAN Filter If the function is enabled the system will reject to response the ICMP ping packets coming from the WAN Block port scan Enable Disable the function of Block port scan The port scan actions will be dropped if you enable this function Block SYN Flood Block TCP SYN Flood or not If this function is enabled it can prevent the system from being attacked by a large amount of SYN packets SPI Firewall SPI stateful packet inspection also known as dynamic packet filtering helps to prevent cyber attacks by tracking more state per session It validates that the traffic passing through that session conforms to the protocol 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O 0 KORTE X Ps O 4 5 9 Management 4 5 9 1 System You may configure language administrator s account and password NTP and DDNS settings here System Management You may configure administrator account and password NTP settings here Language Settings Select Language English he Adminstrator Settings Account Password Apply NTP Settings Current Time Sat Jan 1 01 34 54 UTC 2000 Time Zone GMT 01 00 Germany NTP Server NTP synchroni
27. PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s i DHCP Type DHCP stands for Dynamic Host Configuration Protocol The DHCP section is where you configure the built in DHCP Server to assign IP addresses to the computers and other devices on your local area network LAN When you select Server item from this pull down list to enable this function the following parameters will be displayed You must enter the IP address Subnet Mask Primary DNS Server and or Secondary DNS Server Start IP Address Specify the DHCP Client IP address that will start End IP Address Specify the DHCP Client IP address that will end Note The number of the End IP must be greater than Start IP and cannot be the same as the router s IP address DHCP Lease Time Designate the amount of the time for the device to recycle and give out the IP addresses to the devices in your network default 86400 Statically Assigned You can statically assign the client MAC and IP address Up to three IPs and MAGs can be assigned 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s ol 4 5 4 DHCP clients In this section you can see clearly which devices are currently leasing IP addresses that you had defined for the DHCP Server s allocation of addresses to computers and devices on your Local Area Network DHCP Client List DHCP Clients Hostname MAC Address IP Address Expires i
28. These can be entered in upper or lower case SMS is the last 4 digits of the IMEI password and the command Connect or go orders you can view the IMEI number IP address received from the GPRS 3G 4G and the module reception level CSQ The answer is done only on the number of the SMS sender Order bb Reboot the router Examples of SMS with the IMEI 358178041055718 5718connect or 5718go 5718bb SMS return will consist of the IMEI unique number of the module public or private IP address and module reception level CSQ Example http 80 214 118 34 IMEI 352347031832032 CSQ 22 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s o 4 5 9 5 TELNET The KX ROUTER 4G LTE PRO has a control interface Telnet on port 2000 accessible from the LAN ports or remote Locally you must type in command mode cma Telnet IP of the router 2000 Default Telnet 192 168 8 1 2000 or 2000 if the initial configuration has been loaded into the KX ROUTER 4G LTE PRO The login and default password is admin ex Telnet 192 168 8 1 Kortex Login admin Password www Kortex PSI Kx ROUTER 4G LTE PRO U 51 10 00 05 IMEI 358178042662579 CCID 8933269516606862376 8 179 229 CSQ 16 PLMN 26826 Display this page Reboot the router Ping IP address Display configuration Quit This interface allows among others e Display the IP address and othe
29. X PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s i 4 5 3 LAN settings These are the settings of the LAN Local Area Network interface for the router The router s local network LAN settings are configured based on the IP Address and Subnet Mask assigned in this section The IP address is also used to access this web based management interface It is recommended that you use the default settings if you do not have an existing network Local Area Network LAN Settings You may enable disable networking functions and configure their parameters as your wish LAN Setup IP Address 192 168 8 1 Subnet Mask 255 255 255 0 MAC Address 00 09 B5 21 36 81 DHCP Type Server Start IP Address 192 168 8 100 End IP Address 192 168 8 200 Subnet Mask 255 255 256 0 Primary DNS Server 168 95 1 1 Secondary DNS Server 8 8 8 8 Lease Time 86400 MAC Statically Assigned Statically Assigned C MA Statically Assigned IP ET Setting the LAN parameters include IP Address Subnet Mask DHCP etc IP Address The IP address of your router s LAN port Default 192 168 8 1 Subnet Mask Subnet Mask of your LAN default 255 255 255 0 All devices on the network must have the same subnet mask to communicate on the network 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX
30. Z DMZ IP Address Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication If this computer obtains its address automatically using DHCP then you may want to make a static reservation in the field of Statically Assigned on the nternet Settings gt LAN setting page so that the IP address of the DMZ machine does not change Except TCP port 80 If you click on the checkbox in front of Except TCP port 80 function it means that TCP port 80 cannot be used for DMZ otherwise you can use this port for DMZ 4 5 8 4 System Security To improve the safety of the internal network environment the KX ROUTER 4G LTE PRO offers a variety of basic firewall management functions including Remote management via WAN Ping from WAN Filter Block port scan Block SYN Flood and SPI Firewall By the configuration the following system security settings you can protect the router itself from being attacked scanned or intruded 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTE X Ps System Security Settings You may configure the system firewall to protect AP Router from unauthorized access Remote management Remote management via WAN Ping from WAN Filter Ping from WAN Filter Disable vw Block Port Scan Block port scan Disable v Block SYN Flood Block SYN Flood Disable Stateful Packet Inspection S
31. ccess to services on your LAN This feature is useful for hosting online services such as FTP Web or game servers For each Virtual Server you define a public port on your router for redirection to an internal LAN IP Address and LAN port For Example You are hosting a Web Server on a PC that has LAN IP Address of 192 168 0 50 and your ISP is blocking Port 80 1 Enter the IP Address of the machine on your LAN for example 192 168 0 50 2 Enter the Public Port as 8888 3 Enter the Private Port as 80 4 Select the Protocol TCP 5 Click the Apply button to add the settings to the Virtual Server Table 6 Repeat these steps for each Virtual Server Rule you wish to add With this Virtual Server entry all Internet traffic on Port 8888 will be redirected to your internal webserver on port 80 at IP Address 192 168 0 50 Virtual Server Virtual Server Enable IP Address l Public Port Private Port Protocol TCP amp UDP Comment I The maximum rule count is32 Apply Reset Current Virtual Servers in system No IP Address Public Port Private Port Protocol Comment 1 192 168 0 50 8888 80 TCP Web Delete Selected Reset 91 rue R aumur 75002 PARIS Tel O1 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX on PSI O Virtual Server Enable Disable the function of Virtual Server IP Address The IP address of the syst
32. e Settings This mode settings exist only when 802 1 1b g n mixed mode or 802 11n only 2 4G is chosen as your router s Network Mode Operating Mode Select the option to enable the Mixed Mode or the Green Field Mode for physical layer transceivers Default Mixed Mode Mixed mode In this mode the device transmits the packets with preamble compatible legacy 802 119 so they can be decoded by legacy devices The device receives and decodes both Mixed Mode packets and legacy packets Green Field mode The device transmits HT packets without legacy compatible part But the device receives and decodes both Green Field and legacy packets Channel BandWidth This option only works when selecting Network mode in 11b g n mixed mode and 11n mode Select the option to choose 20 MHz or 20 40MHz This option affects the Phy data rate of radio Please refer to the table below which shows the relationship among Phy data rate Bandwidth and Guard Interval Guard Interval The 11n device inserts the Guard Interval into the signal You can choose the interval between Long and Auto This option affects the Phy data rate of radio For more details please refer to the table below MCS It means Modulation Coding Scheme The available options are Auto 0 1 15 and 32 It changes the modulation of this device and effect the maximum Phy data rate We recommend Auto setting For more details please refer to the table below 91
33. ed to an Ethernet device SAN Green for 100Mbps Orange for 10Mbps Blinking when data is transmitted received 11 Lit when the router is ready to use Phone Lit when the router is attached to the networks 3G Flash when the data is transmitting in 4G 3G networks Off when dialup is disconnected Low 1 3 Cellular Signal Strength LEDs All 3 LEDs lit when the Medium 2 signal strength is good The LEDs lit would decrease progressively upon the signal strength High 3 prog y up g g 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX2s 4 4 Rear Panel LAN 1X 4X RJ 45 connector ANTENNA CONNECTOR Connect an SMA antenna sm Insert a SIM card into the SIM card holder gd WAN RJ 45 connector KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O ss a gt After the device is powered on press the reset button to restore to factory default settings 10 seconds above restore to factory default settings this is used when you cannot login to the router E g forgot the password Connect a UTP Ethernet cable Cat 5 or Cat 5e to one of the four LAN ports when connecting to a PC or an office home network of 10Mbps or 100Mbps Connect a UTP Ethernet cable Cat 5 or Cat 5e to the WAN ports when connecting to a xDSL router or an office home network of 10Mbps or 100Mbps Connect the supplied power adapter to this jack 91 rue R aumur 75002 PARIS Tel O1 34 O4 37 62
34. em on your internal network that will provide the virtual service for example 192 168 0 50 Public Port The port that will be accessed from the Internet Private Port The port that will be used on your internal network Protocol Select the protocol type including TCP UDP or TCP amp UDP used by the service Comment Input any text to describe this mapping Up to 16 alphanumerical characters can be filled in Virtual Server Mapping List After completing the above settings please click on the Apply button The entry of Virtual Server you had added will be listed on this table if it is created successfully Clicking on the Delete Selected button will remove the existing entry you select from this table 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s oi 4 5 8 3 DMZ Settings DMZ means Demilitarized Zone If an application has trouble working from behind the router you can expose one computer to the Internet and run the application on that computer Note Putting a computer in the DMZ may expose that computer to a variety of security risks Use of this option is only recommended as a last resort DMZ Settings You may setup a De militarized Zone DMZ to separate internal network and Internet DMZ Settings Disable DMZ IP Address WAN DMZ IP Address 4G Except TCP port 80 DMZ Settings Enable Disable the function of DM
35. ernet is always maintained VPN VPN Connection Type IA Y Server IP User Name Password Keep Alive Operation Mode Keep Alive Mode Redial Period 60 senconds 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s o 4 5 5 2 PPTP VPN VPN Connection Type PPTPRK4 PPTP Mode Server IP User Name Password Keep Alive Operation Mode Keep Alive Mode Redial Period 60 senconds PPTP Point to Point Tunneling Protocol uses a virtual private network to connect to your ISP This method of connection is primarily used in Europe This method of connection requires you to enter a Username and Password provided by your Internet Service Provider to gain access to the Internet Server IP Address The ISP provides this parameter if necessary The value may be the same as the Gateway IP Address Operation Mode The KX ROUTER 4G LTE PRO allows you to set the reconnection mode The setting is u Keep Alive A connection to the Internet is always maintained 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O 4 5 6 Advanced Routing This section mainly introduces what is Routing Table and how to configure static routing 4 5 6 1 Routing Table This page shows the key routing table of this router
36. f mobile communication technology the mobile data communication network using GPRS CDMA EDGE EVDO HSDPA HSUPA HSPA LTE has covered many regions in the world And network is very stable All these make a large market for wireless terminals Different industries have different applications and different information needs so the industry application solutions provided by the mobile communication operators must satisfy both the common needs and the special individual needs of the industry users perfectly Therefore in recent two years based on the needs of industry users Telecommunication Telecom Operator do innovative practice energetically in mobile application and provide solutions to meet the unique needs of the users Being different with the popular data requirements industry application is very professional Different industry users need different terminals So hardware and software development and system integration must be accord with different industry needs By analyzing the different industry application features in recent years and according to the network features and the actual condition of the network operators we launched the individually designed KX ROUTER 4G LTE PRO KX ROUTER 4G LTE PRO provide users the high speed always online and transparent data transmission communication network to meet the needs of Electronic Power System Automation Industry Monitoring Transportation Management Weather Environment Protection Pipe Netwo
37. l Local Area Connection Properties General Advanced Connect using E Realtek RTL8102 8103 8136 Family This connection uses the following items C2 E Client for Microsoft Networks v File and Printer Sharing for Microsoft Networks v 2 005 Packet Scheduler Internet Protocol TCP IP Description Transmission Control Protocol Internet Protocol The default ide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected Notify me when this connection has limited or no connectivity OK Cancel Choose automatically or input IP manually 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 J KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX si O Internet Protocol TCP7IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the bb gt address P addre subnet Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server 4 2 2 Login the router gt Open the Web browser and type http 192 168 8 1 into the address field and press
38. n siemens sami 00 08 A1 08 C6 3D 192 168 8 100 23 46 55 List the Clients which gain IP address from DHCP Host Name A name for each computer or device that is given an IP address by the DHCP Server This may help you keep track of which computers are assigned this way MAC Address A MAC address is usually located on a sticker at the bottom of a network device The MAC address is comprised of twelve digits Each pair of hexadecimal digits are usually separated by dashes or colons such as 00 0D 88 11 22 33 or 00 0D 88 11 22 33 IP Address The address which is obtained from the DHCP Server Expires in The remaining time of the IP address s lease A specific LAN device no longer needs the leased IP address when the time ends up and this device will also free the IP address it had leased 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s o 4 5 5 VPN 4 5 5 1 L2TP L2TP Layer Two Tunneling Protocol uses a virtual private network to connect to your ISP This method of connection requires you to enter a Username and Password provided by your Internet Service Provider to gain access to the Internet L2TP Server IP Address The ISP provides this parameter if necessary The value may be the same as the Gateway IP Address Operation Mode The KX ROUTER 4G LTE PRO allows you to set the reconnection mode The setting is u Keep Alive A connection to the Int
39. nfo pppd 3410 CHAP authentication succeeded Kortex daemon debug pppd 3410 sent IPCP ConfReq id 0x1 lt addr 0 0 0 0 gt lt ms di Kortex daemon debug pppd 3410 rcvd IPCP ConfNak id 0x1 lt ms dnsl 10 11 12 13 Kortex daemon debug pppd 3410 sent IPCP ConfReq id 0x2 lt addr 0 0 0 0 gt lt ms dt Kortex daemon debug pppd 3410 rcvd IPCP ConfReg id 0x0 Kortex daemon debug pppd 3410 sent IPCP ConfNak id 0x0 lt addr 0 0 0 0 gt Kortex daemon debug pppd 3410 rcvd IPCP ConfNak id 0x2 lt addr 176 178 179 22 Kortex daemon debug pppd 3410 sent IPCP ConfReq id 0x3 lt addr 176 178 179 22 Kortex daemon debug pppd 3410 rcvd IPCP ConfReq id 0x1 Kortex daemon debug pppd 3410 sent IPCP Conf ck id 0x1 Kortex daemon debug pppd 3410 rcvd IPCP ConfAck id 0x3 lt addr 176 178 179 22 Kortex daemon warn pppd 3410 Could not determine remote IP address defaultir Kortex daemon notice pppd 3410 local IP address 176 178 179 229 Kortex daemon notice pppd 3410 remote IP address 10 64 64 64 Kortex daemon notice pppd 3410 primary DNS address 62 201 129 99 Kortex daemon notice pppd 3410 secondary DNS address 62 201 159 99 Kortex daemon debug pppd 3410 Script etc_ro ppp ip up started pid 812 II AA AA AAF SA AAP ET TE VE EE CC CL ay Oe F i F F V a 4 S A V V GS Gs Gs s s s s s s s s s Gs From the system log you can read the various situations after the system starts
40. nly obstruct outside intruders from intruding your system but also restricting the LAN users Port filter restricts certain type of data packets from your LAN to Internet through the router You may setup firewall rules to protect your network from virus worm and malicious activity on the Internet Basic Settings MAC IP Port Filtering Disable M Default Policy The packet that doesn t match with any rules must be Dropped Y Apply MAC IP Port Filter Settings Source MAC sddress Dest IP Address Source IP Address Protocol None Dest Port Range Source Port Range L Action Accept M Comment The maximum rule count is 32 Apply Current MAC IP Port filtering rules in system per Dest IP Source IP N ss No MAC Address Address Protoco Port Action Comment Cnt address Range Packets dropped that don t match with any rules above 91 rue Reaumur 75002 PARIS Tel OI 34 O4 37 62 ce KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX in PSI O This section is mainly about MAC IP Port filter settings Basic Settings MAC IP Port Filtering Enable Disable the function of MAC IP Port Filtering Default Policy The packet that doesn t match with any rules would be Dropped Accepted For example if you select Dropped all packets that do not match the rule you set up in the following MAC IP Port Filte
41. on feature of the router Simply click on the WI Fi ON WI Fi OFF button The system will automatically detect the current status of the router and switch the button accordingly Network Mode There are 5 modes including 802 11b g mixed mode 802 11b only 802 11g only 802 11 b g n mixed mode and 802 11n only 2 4G can be chosen Network Name SSID When you are browsing for available wireless networks this is the name that will appear in the list unless you set it to Hidden see below This name is also referred to as the SSID For security purposes itis highly recommended to change from the pre configured network name Default is Default Wi Fi Hidden The option allows you to hide your wireless network When this option is unchecked your wireless network name is broadcast to anyone within the range of your signal If you re not using encryption then they could connect to your network When you click on this checkbox to enable this function you must enter the Wireless Network Name SSID on the client manually to connect to the network Multiple SSID 1 3 Up to three SSIDs you can additionally set up for this wireless network Broadcast Network Name SSID Enable Disable the SSID broadcast function This function is used to control the broadcast status of all SSIDs If this function is disabled all SSIDs you had set up for the router will be hidden To cancel the hidden status for the specific SSID you can uncheck the Hidden
42. ringSettings would be dropped MAC IP Port Filtering Settings Source MAC address Fill out the MAC address that you wish to filter Dest IP Address Fill in the destination IP address that you wish to filter Source IP Address Fill in the source IP address that you wish to filter Protocol Select the protocol type of TCP UDP or ICMP Dest Port Range Fill in the destination port range that you wish to filter Source Port Range Fill in the source port range that you wish to filter Action You can either choose Accept or Drop to permit or prevent the action Comment Input any text to describe this mapping up to 16 alohanumerical characters MAC IP Port Filter Rule List Lists the MAC IP Port Filter Settings you have added before Click on the Delete Selected button to delete the selected list 4 5 8 2 Port Forwarding This function offers the way of Port Forwarding Virtual Server in order to help redirect requests from computers on the LAN to a server set up on the LAN You can set up an Internet service on the computer on local network without exposing it on Internet directly You can also build many sets of port redirection to provide many different Internet services on different local computers via a single Internet IP address 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O Create a Port Forwarding In this section you can add a new por
43. rk Monitoring Finance Bond industries and pos terminals 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX2 mer 2 2 Specification gt CPU RAM 256Mbit x FLASH 64Mbit gt Power Input Input DC 6 12V standard DC8V 1A 5 8 0W max x Low voltage over current over voltage anti reverse protection gt Environment lt x Storage Temperature 20 C 60 C xx Work Temperature 10 C 65 C lt x Humidity 5 85 gt Volume 4 L W H 110 155 32mm gt Weight x Net weight no accessories 255g gt Data Interface 1 WAN 4LAN 10 100Mb RJ45 gt WIFI xx Transmitting power 802 11n 11dbm 802 11g 13dbm 802 11b 15dbm xx Distance 80 100 m in open area 30 50 m interior xx Allow 32 users to access in theory xx Electrostatic discharge immunity EN6100 4 2 level 2 RFEMS EN6100 4 3 level 2 xx Surge EN6100 4 3 level 2 PFMF EN6100 4 6 level 2 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX on PSI O x Shockwave immunity EN6100 4 8 Horizontal vertical direction 400A m gt level 2 gt Physical property Shockproof IEC60068 2 27 xx Drop test IEC60068 2 32 x Vibration test IEC60068 2 6 gt Applications area Pos terminals ATM terminals access internet Environment monitor Remote meter reading Distribu
44. rs information e Reboot the box KX ROUTER 4G LTE PRO locally or remotely e Ping a specific host 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s men 4 5 9 6 Firmware Software upgrade tool is used to help upgrade the software function in order to fix or improve the function User can upgrade the firmware in this page Please note that power cannot be off in the process of the software upgrade You must do it carefully Specify the filename and directory where the file is located via the Browse button and click on the Apply button when it is completed When the upload is finished the router will start upgrading software A reboot message will be prompted after completing upgrading software At this time you must reboot the router to have the new software worked If your upload is unsuccessful an error message will be shown in the webpage and it will not upgrade the software as well Upgrade Firmware Upgrade the firmware to obtain new functionality The update process takes approximately 1 minute Wait for the program to complete the update Upload Firmware Location Parcourir _ Location File path and filename stored the image file you would like to upgrade Upgrade the firmware to obtain new functionality It takes about 2 minutes 4 5 9 7 Configuration With this function user can back up or reload the config files by exporting importing
45. t forwarding to the port forwarding table below or delete an existing entry from this table Port Forwarding Port Forwarding Enable IP Address 7 Port Range H j Protocol TcPsupP Comment The maximum rule count is32 Apply Reset Current Port Forwarding in system No IP Address Port Range Protocol Comment 1 E 192 168 0 100 100 111 TCP UDP Delete Selected Reset Port Forwarding Enable Disable the function of Port Forwarding IP Address Fill in the IP address of your LAN Server Port Range Fill in the port range that you wish to filter Protocol Select the protocol type including TCP UDP or TCP amp UDP used by the service Comment Input any text to describe this mapping Up to 16 alphanumeric characters can be filled in Port Forwarding Mapping List After completing the above settings please click on the Apply button The entry of Port Forwarding you had added will be listed on this table if it is created successfully Clicking on the Delete Selected button will remove the existing entry you select from this table 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 J KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s om Create a Virtual Server In this section you can add a new virtual server to the virtual server table below or delete an existing entry from this table The Virtual Server option gives Internet users a
46. ternet Settings 14 ADD WAIN Seinos enaa pa au na E E E aE IET e ie E TIa t nae Qha pise tests t ei 15 ADS LAN SCUINGS csi u aa a E EEE EA E AET ER ATT ORES 16 4 3 4 DHCP lenin aid San E A S u l uq asss 18 PII VEN at dan aa yasa E na Sau 19 ADO Advanced Roles a asuata ia akaqa ic 21 4 5 7 Wireless settings sense 23 4 557 Basic Wireless Settings sisi arriere nent nent aa ete 23 4 5 7 2 Wireless Security Encryption Settings ss 27 ASS AN EL O OO NN 30 ADT A SIQHSHOSO SO aa s nt ia 31 ASSP UPC ET cas os RER wens dana Sata va bs boned ED E E Er I 32 4 5 8 1 MAC IP Port Filter Settings ses 32 438 2 PortiFiorwarding u yuana ici diari ste anna sa ives seen E EESE En EE ttes eine 33 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 ce KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O O KORTEX si O j 290 3 DMZ Setin A A EATE TS 37 4 3 8 4 Systemi SECUTUY ni E E E E E de E di tees 37 AO MONG SCIEN qa pataka ha u E EE EEE A E E E AEE E O il 39 TE SV SUC E AN 39 AS DD SIM ua Sa a E EE E TE ici 41 4 5 DS TROO G i 44 RN 45 ANDO LEEN A tds veo 46 A IA sissien a EE i n R Las bsebesadvctnslasdade sea N EE EEEE Ei aE 47 4 5 98 SAUS a NC 49 ANDINOS A A a ent el 50 LNI TOS VSEM oo tin a nuusan suasana spa ER OOO 51 CHAPTER 5 FAQ u asaasaawwaywayshaqowasakaswasshuaykayyasqawqasyaycaysssiswassayaykaysasqaydsksqossssaasyvassassswayis 52 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4
47. tion automation Outdoor LED Smart home Oil monitor Car video surveillance Coach bus X X X X y X Xe Fy XX XX XX XX XX XX LE LE Chapter 3 Installation Here you can see the appearance of KX ROUTER 4G LTE PRO and how to install 1 Accessories 2 Edition 91 rue R aumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s o 3 1 Accessories KX pc 1 router ROUTER 4G LTE PRO WU Power pc 1 standard Antenna pc 2 Integrated for WIFI one for 4G I SMA connector RJ45 cable pc 1 standard User manual pc 1 standard 3 2 Installation KX ROUTER 4G LTE PRO must be properly installed and configured to meet the design features Note Please install the router and SIM card before inputting power 91 rue R aumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O Chapter 4 Configure 4 1 Overview The router has its own webpage for parameter settings You can access the router by the following way 4 2 Connection 4 2 1 Computer network configuration Find Local Area Connection and choose Properties LAN or High Speed Internet oc al At Area Connection C gt Cisco AnyConnect Secure Pe A Mobility Client Connection Disable Status 3 Repair LL tpi Bridge Connections Create Shortcut Rename Les Choose Internet Protoco
48. tting massive data Decline BA Request Enable this option to decline the Block ACK request addressed by the other devices 91 rue Reaumur 75002 PARIS Tel Ol 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX PSI O 4 5 7 2 Wireless Security Encryption Settings In this section you can configure the wireless security and encryption to prevent from unauthorized access and monitoring Please choose a SSID you had created for this router in the Wireless Settings 2 Basic setting page from the SSID Choice pull down list There are 4 encryption modes including Disable WEPAUTO WEP WPA PSK and WPA2 PSK offered for your selection Please also pull down the Security Mode list and select the desired mode for your router s wireless security For more details about the setup in these different modes please refer to the following sections Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from unsuthorized access and monitoring SSID choice defautt v Security Mode Disable v y The SSID select from multi SSID setting Security mode include disable wepauto wpa psk wpa2 psk WEPAUTO WEP Mode WEP is a method of encrypting data for wireless communication intended to provide the same level of privacy as a wired network WEP is not as secure as WPA encryption To gain access to a WEP network you must know the key The key is a string of characters that you
49. unction and new PIN code accordingly Also re key this new PIN into the Confirm New PIN field of this function before pressing the Apply button for authentication The system will return the message in the pop up window for you to realize whether your setting is successful or not 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s O 4 5 9 3 TR069 TR 069 is an application layer protocol for remote management of end user devices Using TR 069 clients can specify another Auto Configuration Server ACS Usually the default settings on the TR 069 Client screen work fine To view or change these settings TR069 URL https 50x xx xx xx 6060 openacs acs Enable Disable v Interval Time 1800 Sec 91 rue R aumur 75002 PARIS Tel Ol 34 O4 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX s mee 4 5 9 4 SMS The KX ROUTER 4G LTE PRO has a function to be controlled via SMS You can send a SMS to the number of the M2M SIM card in the router KX ROUTER 4G LTE PRO a reply SMS will then be sent back if the issuance SMS are allowed on the SIM card You must first make sure with the operator company it is able to provide this service and transmit SMS reception The cost applied for such a service may be charged a flat rate penalty or unit basis Two commands are available for use by SMS
50. zation DDNS Settings Dynamic DNS Provider Dyndns org Account Password DDNS Language Settings Select the language which you would like It includes English and Portuguese Administrator Settings Modify the account and password to set up and manage the router The default settings for administrator are as follows 91 rue Reaumur 75002 PARIS Tel OI 34 04 37 62 KORTEX PSI KX Router 4G LTE Pro User Manual V1 1 O KORTEX mn PSI O Username admin Password admin NTP Settings Set up the system time by syncing from the NTP server or your PC Sync with Host Click on the button of Synchronize with host to synchronize the timer built in the router with the computer you are using Current Time Show the system time of the router Its format day of week month day hours minutes seconds year For instance Wed Aug 29 12 10 10 2012 Time Zone It is an offset time off GMT You have to select the time zone first and then perform time sync via NTP because the router will combine this time zone offset and updated NTP time to come out the local time otherwise you will not able to get the correct time The router supports configurable time zone from 11 to 12 step 1 hour Default Time zone 11 Hrs NTP Sever NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean Time GMT If you manually specify an IP address of user defined NTP
Download Pdf Manuals
Related Search