Home

User's Manual of

1. Idle Acctrnmise 000 000 Start speed mrmnys 15 000 Min Acctrmmysz 500 000 Max Accimm isz 000 000 Cutting mode Normal Cutting Acc Mode 5 mode Idle speed this parameter decides the max speed of all lines not emitting beams during the operation of the machine This parameter should not be lower than the lower of the jump off speed of the X axis and that of the Y axis and not exceed the higher of the max speed of the X axis and that of the Y axis if the setting is illegal the controller will automatically set this parameter within the range above a comparatively high idling speed can shorten the operation time of the entire figure while excessively high idling speed may cause dithering of the tracks therefore you should take all relevant factors into consideration when setting Idle Acc Corresponds to the acceleration of the speed of air travel time air and air way way speed of acceleration to match if you set too slow the actual speed may not reach the air way set value if set too fast they may not withstand the mechanical structure resulting jitter Slightly higher than the general acceleration of air way cut acceleration Cutting Acc Corresponding to the acceleration of the speed of cutting cutting speed is the speed of the layer parameters of the layers Turning speed Turning the corresponding deceleration in the cutting process the minimum speed of the drop when processing a lot of teeth when the graphics may be appro
2. 100 Default Ves T Scan Advance Layer Is Output Speed mmsi IF Blowing Processing Mode Default r Advance Min Powerl Max Powerl 1 Laser 1 30 30 Default ye Min Powerl i Max Powerit o Laser1 30 30 _ Default Laser Laser Negative Engrave Optimized Scan Output direct _ Independent output Ramp Effect Independent output Ramp Length Ramp Length mm Overstriking Un process Overstriking Un process _ Swing Y Cae On the left of the dialog box for vector scanning parameters Settings on the right side of the Scan Mode swing Scan Mode Interval rnm U1 Interval mny 0 1 dialog box for bitmap scanning parameters Settings The vector data do not support the scanning the color carving optimization scanning direct output The color carving normally scanning bitmap in the black spots a laser the laser in white Choose the color carving the bitmap in the white of the laser black spots in a laser Optimal scanning choose optimization will automatically adjust the users scan the scanning interval to set up the best value the scan best effect Otherwise according to user Settings of the scanning interval scan pattern Generally choose optimal scanning Direct output grayscale bitmap acco
3. Cutting property dialog box will pop up All with manual sorting and cut points cutting the direction of the settings in this dialog box can be completed Set cutting property Mame Elementi Elementz Elementa Element4 Elements Element Element Element Element Elementid Elementi 1 Elermentiz Elementis Element14 Element15 Element16 Elementi Element1 Element19 Elementz0 Elementz1 Element22 Element23 Element24 Element25 Element26 Element Elementz8 Elementz9 Flementso Eae p T m x Show path First check the show path it will display the current graphics cutting order and the cutting direction Manual sort Select Rl This button is used to switch the current status of the operation is to edit or view Then you can marquee or click the graphics in the graphics display area or click one pixel or check many pixels After selecting the graphic select gt gt these graphics to be redirected to another list to be processed as the first primitive Primitives followed by repeated operations to complete sequencing of all graphics Change the direction of graphic processing Mouse select the graphic in the graphics display area or in the list And then click ASTROK WARE Change the cutting point Set cutting property Mame Elementi Elementz Elementa Element4 Elements Element6 Element Element Element Elementid Elementi 1 Elementi Element13 Element14 Ele
4. J Enable error Errortrorcnit Data check integration of the closed inspection the inspection the inspection the intersection of the fellowship data overlap a check The user can select a check inspection to the problem after data will be in the dialog box right tip have been found and at the same time the problem in selected state graphics Check gt ruled out repeatedly error gt inspection process until all the data are conform to the requirements of the processing 2 13 11 Generation parallel lines Selected to create parallel lines after the data click on the menu commands the Handle Offset poly or click system toolbar 6 Offset poly OFFsekt rm 0 1 mm _ Delete artwork In Out Auto In Out Cancel Red line in the figure for the original graphics green line is inside shrink graphics 2 13 12 LGP design Click the menu commands the edit LGP design or click drawing toolbar already can start reflex block design tools the tools are specific to block the sun processing is an independent functions such as the user is not involved in the sun block can be ignored this section processing content Play channel tabula rasa design tools we first need to design a reflex guide the outline Play channel tabula rasa design tools we first need to design a reflex guide the outlin RuiDa ACS ASTROS WARE LGP CAD amp CAM System X Parameter Output System L
5. beem S eS fe O m Ah x Laser work SaveToUFile UFileOutput Path optimize C Output select graphics Device USB Auto e a E Position Current positic W Le ERRA te lee aR HSS SS BE HRS T RARR E024 768 R kA ale LAERE RS AR X 329 345mm Y 177 307mm Menu Bar The main function of this software are available through the implementation of the Menu Bar Execute the menu command is the most basic mode of operation Menu Bar including Document Edit Draw Setting Processing View and Help System Bar On the System Bar placed some most commonly command buttons which is chosen from the menu Graphics Bar Graphics property bar is the basic attributes of graphics operations including graphic location size scale number processing Edit Bar The Edit Bar default on the left of the work area In the Edit Bar placed frequently used tools to make the operation more flexible and convenient Align Bar Alignment of the selected objects Layer Bar Change the layer of the selected objects Control Panel Using the Control Panel to complete laser processing of multiple tasks Layer parameter settings axis control processing etc 2 2 Language settings and manufactures information ASTROB WARE In addition to installation process can set the software language type you can easily switch in different language Click Menu Bar Help gt DE Language expand menu select the required language t
6. Laser head back to the position before processing Original anchor Laser head back to the last anchor the anchor may set at panel Machine zero Laser head back to the zero of the machine 4 4 Go Scale Cut Scale For Example Go Scale As the following figure shown the actual graphic is round and the red rectangle outside the circle is the smallest rectangle click button Go Scale laser head will run once along the rectangular path For Example Cut Scale As the following figure shown the actual graphic is round and the red rectangle outside the circle is the smallest rectangle click button Cut Scale laser head will be cut along the rectangle 4 5 Start Pause Stop SaveToUFile UFileOutput Download Start Output the current graphic to the machine for processing Pause Continue Click Pause will stop the processing work click the button again to Continue Stop Stop the current processing work SaveToUFile Save current file as RD format using for offline processing Can be copied to other memory board for full offline operation UFileOutput Output the offline file RD format After save offline file click UfileOutput to select rd file to processing Download Download the file to the memory of the controller then user can start the file through the machine panel 4 6 Output select graphics After check Output select graphics then only output the selected part rather than not output the part not
7. _SaveLFile _OutputuFile LP Size mm Width 218 1 Height 200 0 Lock ratio Apply Enable LGF blank If the outline of import size requirements users can also change size outline and can set up if stay white edge Outline graphics ready they can start on the tabula rasa increase network ASTROS WARE LGF Pointimm LaF type width jooo Height 1o00 Uporad jooo Uporad o oo DownGrad 0000 DownGrad o oo Lefkisrad la cooa Leftarad o oo Rightisrad jogoo RightGrad fo cooa Spacet nm Up arad Down Grad Left Grad Right Grad Base line Zerg vi 0 000 Zero Y 0 000 Enable row and colown EnRo EnZolumn Light source Left Right Top Bottom Apply Network is divided into four ways straight line elliptical rectangle and the grid Network is divided into four ways straight line elliptical rectangle and the grid Baseline related with light source the user can adjust the baseline position according to time light source In the figure above red graticule marker is the baseline users can move the mouse to baseline press the mouse and then drag the baseline to want to position The entire guide baseline reflex is divided into four regions level above baseline definition for uplink and downlink below defined as Vertical baseline definition for the left column on the left the right to define right column Set respectively size and spacing network r
8. are improperly adjusted this effect may not be achieved and the working mode of high power and short period may influence the service life of the laser The default mode is the general mode Facula Size When scanning the general pattern of selection the argument is invalid when you select a special mode the onset of the parameters Control the parameters of control in 50 to 99 respectively 3 3 3 Home parameters H Home para Home speedimm s 80 000 Auto home x Yes Auto home Yes Auto home z Mo Auto home LU Mo Home speed This parameter determines the machine is turned back to the origin when the speed of a larger format if the machine can be set to reset the speed is too large but not too much X Y Z U Auto home The axis can be set whether should reset at boot time 3 3 4 Go Scale parameters ASTROK WARE H Go Scale para G0 scale mode Close laser Go scale blankimmi 0 000 Go scale mode Points of light to go off the border the opening cut borders corners three modes Go scale blank Walking frame can be based on the actual image size up and down again about the direction of some of the white left side of the border in order to ensure complete contains the actual graphics This setting is on the control panel to go with the border related functions while walking on the border with the independent software 3 3 5 Other parameters H other parameters Array processing Bi dir Array Return position Absolute O
9. it is worth noting that if we want to output serial number is ABCIDEF ABC2DEF until ABC9999DEF we can t through the will start SN set to 1 to achieve but through the cancel Enable prefix ZERO to achieve this is ASTROB WARE because set in the specified number from the start the serial number which one beginning outside also specifies the number of significant digits such as will begin to serial number set to 1 the change of the serial number order is 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 Serial number won t change to 10 because the effective a serial number had 1 Enable SN array to the array of way one time processing more serial number for instance 0001 0002 0003 after this batch processing serial number 0015 0014 0013 0006 0005 0004 skip directly to the next group of 0007 0008 0009 0016 0017 0018 0016 0017 0018 Capture Click menu Draw gt Capture or click Edit Bar If the computer has been connected to the image device the dialog box will appear After it was Selected you can collect the pictures from the specified device 2 7 Object Selection In the process of drawing and edit graphics first of all is to select the object When the object is being selected in the center of this object will have a shaped mark x and surrounded by eight control points Click menu Draw gt Select or click Edit Bar R switch to status Select Under this status you can select object The following ar
10. load conditions vary Since X Y axis load generally much higher than the X axis Y axis accelerometer Line shift speed of scanning this parameter is specially used to control the max speed of the scanning to shift vertically from one line to the next line below it If during the scanning the line space is too large or the block space is too large when scanning block figures while precise positioning for each line or block is required you can set the line shirt speed of scanning to a comparatively low value This parameter cannot be less than the jump off speed of the corresponding axis during the line shift and cannot be higher than the max speed of the corresponding axis during the line shift if the setting is illegal the controller will automatically set this parameter within the range above Scan mode There are two modes for your selection the general mode and the special mode in the general mode there s no any treatment during the scan in the special mode light spots will be treated If the special mode is activated the power of the laser should be increased and correspondingly the light spot percentage will be lower and the laser power attenuation will be higher to achieve the same depth of scanning the laser power should be higher The purpose to select the special mode is to make the laser to emit beams at high power and in short period during deep scanning the effect of flat bottom can be achieved however if the light spots
11. machine The default coordinate system if Descartes coordinate system and zero in the bottom left If the zero point of the machine is top left then X Axis do not need to mirror but Y Axis need to mirror If the zero point of the machine is top right then both X Axis and Y Axis are all need to mirror In addition this function can also use to other application for mirror ASTROB 3 WARE Default RD5 0 0 9 Seles File E Edit E Draw D Config S Handle W View VW Help H Deh AG ea RARA RA DOA r wO Aste Go Bo 511 569 mm 705 _ mm If 10 ee 357 mn Masos mn 100 oe tal BI O 2000 4000 6000 8000 1 I I 1 I I an I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I lt Xx 10000 12000 PO ee dG O S O S O R N A A A ne o S A g x ds BB a O FPE Work Output Doc User Test Transform 3 Layer Mode Speed Power Output A v m Down _ Device Find com Com Auto vi Laser work Position Current positic Cese Co ee eee ee SaveToUFile UFileQutput C Output select graphics Path optimize Fe ak OW ON RSTS x4 too eh AY oe AARNE La E Welcome to use the Laser system of cutting Propose the display area 1024 765 or higher XK TT3 957mm 284 STSmm Laser head Position of Laser head means the location laser head relative to the graphic Top Left Top Middle Top Right Middle L
12. may cause the edge of the scanned graphics uneven Therefore increasing backlash to fix It has the specific backlash for the certain speed General the greater the speed the greater the backlash 1 Add backlash Click the Add button the screen will pop up as shown in Figure Speedirnmns Reverse interval rim Set speed and backlash click OK the value to be inserted into the list of backlash 2 Modify backlash Double click the left mouse button scanning reverse gap need to modify the reverse block entry clearance then the pop up screen shown in Figure In the interface can modify the current speed of the corresponding backlash 3 Remove backlash Right click scanning reverse gap block in the backlash to delete the item then click the Delete button ASTROK 3 WARE 3 2 System info setting General settings System Info Vendor password Information on the operation of the motherboard manufacturers need to enter password to view parameters Setting General settings System Info Total on tinmethour min s Total processing timethour minis Previous processing timethour minisims Total laser on timethour min s Total processing times Total travalh Y Total travelinnt Mainboard wersion Total on time The total time of motherboard working RuiDa ACS Total processing time The total time of processing including the time of jump moving
13. more are in the same layer bitmaps and whole as a picture output if hope each bitmap single output it can be a graph respectively placed in different layer can Is Output Have two options yes and no Choice is the corresponding layer will output processing Choose no won t output processing Speed The corresponding processing method of processing speed For cutting processing is concerned the slower processing the better the more smooth track The faster the processing results the worse the trajectory smooth ASTROB WARE To scan for processing the slower under the same energy scanning depth deep and scanning trace the thick scanning the resolution also reduced The faster the same energy the shallow depth of the scanning details distortion increase To fix for processing the main change is empty the speed of the move If check the default the actual speed by panel set up to speed If Blowing f the machine external fan and fan has enabled then if choose is then this layer data processing will open the fan otherwise will not open the fan If you do not make can fan no matter choose yes or no are meaningless Processing methods says the method of processing corresponding layer If the currently selected is vector layer i e color layer it includes three choices laser scanning laser cutting laser rbis If the currently selected is a tutu layer namely BMP layer the only include a choice laser
14. of the graphics 2 9 6 Place Object To The Origin Place the object is to facilitate the view or orientation The following tools are provided by software 5 selected object will be placed in the center of the page that is the object center coincides with the center of the page E Al gt Selected object will be placed on the page left upper right lower right lower left upper left corner of the object upper right lower right lower left and upper left corner top right bottom right bottom left corner of coincidence 2 10 Object Align Select objects click tools on the Align Bar 2 amp 0 8 e Hee eB Whick include Ub OO Left alignment Right alignment Top alignment Bottom alignment oy eb Vertical center alignment Horizontal center alignment center alignment HL amp Horizontal equidistance Vertical equidistance ASTROK WARE E 1 H same width Same height Same size Benchmark object If you press Shift key and select object one by one zhen the benchmark object is the last object If you select object by select box then zhe benchmark object is the object which curve number in the final 2 11 Object View Move Click menu Edit gt Move or click Then hold down the left mouse button in the drawing area and drag pan Zoom Out Click menu Edit gt ZoomOut orclick Each click it the drawing area zoom out once Move mouse to the drawing area and click each click mouse p
15. one dot during the process The higher the value is the darker the dot is if reverse the weaker The interval between the dots Dot interval mn Dot length for cutting dash line Zenter de Only dot at center
16. pen position Use way is 1 gt Can write pen to carry 2 gt Make can write position manual control panel key mobile platform to stay processing graphics graphics processing plane adjust the focal length Then click button read and then write all set up position 3 gt That can carry a position manual control panel key mobile platform move to the optical will not interfere with the work of the height and through the panel key move the optical confirmed that won t interfere some button read and then set up a position point Here the rbis and is suitable for drawing tool create a point figure yuan or from DXF file into the spot diagram yuan And the current layer processing methods has nothing to do namely whether the current layer is cutting or a scan graphics in the spot diagram yuan has always been to the rbi way output The rbi movement speed for layer speed beating the energy for the maximum energy layer laser The laser Enable ASTROB WARE _ _ Z O Y When the machine is equipped with two road laser usually are two road and output But the user may through the set that laser that its not output all the way The joint IO output All the way and the layer associated IO output obligate function 4 10 3 Laser scanning parameters Settings Layer Parameter Ea Layer Parameter Speedirmmys IF Blowing Processing Mode Layer Load parameters From library Is Output
17. scanning Laser 1 laser 2 corresponding to the mainboard laser signals 1 and 2 of the way way laser output If it is only head machine the second road laser meaningless The minimum power the maximum power the power of the values of the range of 0 to 100 said that in the process of the strength of the laser processing Big value the laser is strong is small the laser weak Minimum power loss to the most power is less than or equal to For different processing type has a different meaning For cutting processing the actual power is cutting speed and phase follow speed low energy is also low high speed is high also so that we can guarantee the whole process of cutting energy evenly So the minimum power the speed of the corresponding minimum energy the minimum speed general is 0 but if set the speed is the minimum speed for takeoff take off speed The maximum power correspond to the layer speed Set minimum power and the most high power flow l gt The minimum power and the maximum power set to the same value synchronous adjustment Until all the cutting curve are already appear 2 gt The maximum power unchanged and gradually reduce the minimum power until the energy of the heavy cutting curve at the lowest level and all of the cohesion parts can be processed to come out 3 gt If not yet to best effect can be the most appropriate fine tuning high power and repeat step 2 If is cut through the minimum power loss and the maximu
18. single graphic mm You can array replication object along different directions The direction of copy is based on the orginal graphics Such as choose the array direction lower right then the original graphic will appear on the upper left corner wheras if it is to the upper left array then the original graph appears ASTROB WARE in the lower right After setting the array number and array spacing click button Apply you can see the actual graphics array There are two forms of array spacing center spacing and edge spacing Choose center spacing then X Distance mm Y Distance mm representing the distance of the two graphic center If not choose center spacing then X Distance mm Y Distance mm Jrepresenting the distance of the graphic edge Center distance X Edge distance X width of object Center distanceY Edge distance Y height of object Switch between the two kinds of calculate method X Distance mm Y Distance mm Jwill be calculated automatically Click Bestrewing breadth The software will automatically calculate the array number according to the workpiece sie width height X distance and Y distance Adjust spacing can be directly input values and click Apply Can also press the dirction keys to adjust objects spacing o Check Center then after object array replication graphics will be centered on the work area Scroll the mouse wheel to zoom view of the graphics Drag the mouse to pan view
19. 4 765 or higher X 605 135mm 313 460mm Manual sort Choose the primitive that should be changed the cutting order then the cutting serial number of the current primitive will display in the object properties bar E 243 79 mm 63 862 mm 100 701 941 mm 4 179 859 mm 100 m fel o8FCO 8 ProcessNO 17 Keon 5800 6000 620 0 e400 6600 6800 7000 E 7400 760 0 7300 S000 20 0 Prevlercleversctirselervercliarieclbetrrlarcrberrttlaratclerictirsaclerrctliricecdherrectairear drei poetletcclaoritlerrrtorsederrctarttlorerctorsadberrictacs J ds X pes gt OO Ce N NIA l 20 0 000 Ji iliri 400 600 80 0 Enter the serial number directly in the processing number then press the keyboard Enter key or click the plot area the cutting order will be changed Change the processing direction Click Edit gt Set cut direction to enter the edit mode of the cutting direction Then you can double click on any position on the selected graphic Change the cutting point ASTROK WARE Click Edit gt Set cut point to enter the edit mode of the cutting point Then select the curve that should be edited you can double click on the node that you want to set the cutting point to complete the change of the cutting point 2 13 2 Setting And Editing The Cut In Cut Out Lines Drawing or importing curves the curve is default not have any cut in cut out lines If want to add cut in cut
20. ASTROS WARE Previous processing time The time of the last processing Total laser on time The time of the laser processing Total processing times The number of completed processing not include the processing forcing to end X total travel The total travel of motor X Y total travel The total travel of motor Y Motherboard version The version of the current controller The function of upgrades bin format the user can load the upgrade file to upgrade the motherboard After the upgrade you If the board has additional features the manufacturers will provide the update file need to click on the control panel Reset button reset the motherboard before normal use 3 3 User parameters Work Output Doc User Test Transform EH cut parameters 200 000 2000 000 Idle speedt rimys Idle Acctrmmsz 3 3 1 Cut parameters Start soeed romns Min Acctrorms2 Max Accimmisz Cutting mode Acc Mode Sweep parameters x Start Soeedimriys y Start Soeedi mriys x Acctmmys2 y Acctmmysz2 Line Shift Speed rom Scan Mode Facula Size 50 99 Home para Home speedimiiys Auto home Auto home r Auto home z n Li ee ee I I 15 000 200 000 2000 000 Normal Cutting S mode 20 000 15 000 a000 00g 2000 000 150 000 Common Mode 96 000 80 000 Yes Reading the board parameters must before operating the user parameters ASTROK WARE EE cut parameters Idle speedtmriys 300 000
21. ASTROS WARE User s Manual of Laser Engraving Cutting Software RDCAM6 0 ASTROB WARE Chapter 1 Overview 1 1 Laser engraving cutting system introduction Laser engraving cutting system through a computer numerical control machine tools to achieve effective control according to the user s different requirements of the completion of processing tasks The system including control board and control panel and supporting software This manual describes how to use the software to complete the task of laser processing Motherboard wiring and control panel operations see the accompanying manual and control panel wiring board operating instructions 1 2 Software supported file formats Vector format dxf ai plt dst dsb etc Bitmap format bmp jpg gif png mng etc 1 3 Environmental requirements 1 WindowsXP operating system and above XP recommended 2 Above CPU586 above PIII or PV recommended 3 Memory above 1G recommended ASTROK WARE Chapter 2 Software Basic Operation 2 1 The main interface operation After start the software you can see the interface shown in the following figure Graphics bar System bar Align bar Default SEAR File E Edit E Draw D Configig Handle w View V Help H Deh ae eAaCRAQRaa Dot YwO dae RGF Be BAD OHS HT eR KANYE D mm Work Output Doc User Test Transform Layer Mode Speed Power Output Line column setup Num space mm Dislocation mm x il 0 0 vi e o
22. GP Size mm Width 200 000 Height 200 000 K us ce 3 O a or m m 5 o T a a aq T pa gej o ow 9 i rn f fas o a F ro Apply width 22H Height 200 0 Rectangle O Ellipse Apply Import artwork USB Auto Position Curren t Position v Start Pause Continue l Stop SaveUFile I OutputUFile IL Download Play channel tabula rasa design tools we first need to design a reflex guide the outline In the tool the default created a 200 X200 rectangular guide tabula rasa outline The user can in the tools of system page manually create a standard to the shape of the guide tabula rasa outline Create standard setting the outline can use rectangular or oval Create LGP outline width 200 0 O Rectangle Apply Import artwork Height 00 0 The user can also import a has good graphic design as the outline of the sun Click on the introduction to guide tabula rasa contour button can choose to have the outline of the document as the sun Need to point out that outline file must be closed graphics otherwise the system will automatically deleted ASTROS WARE LGP CAD amp CAN System x Parameter Output System LGP Sizefmm Width 218 1 Height 200 0 Lock ratio Apply C Enable LGP blank La Create LGP outline 200 0 Height 200 0 wid O Ellipse O le Apply Import artwork USB Auto Position Current Position v
23. H 445 91 mim We 500 791 mm _ Lock rotate center Relative center 4_ d_ d do dls O O0 Apply Or use the spin rotation transformation tools to transform In the rotations transformation tool can be set to the center of rotation and locking center of rotation 2 9 3 Object Size z 445 91 mm H 235 989 mm 100 H Y 299 208 mm f 208 549 mm 100 i o ProcessNO 1 O You can set size and center position of the selected object ASTROS 7 WARE Work Output Doc User Test Transform 9 SIZE H 235 989 mm y 208 543 mm Disproportionate d d _d O El O 0 Apply to copy Or use the size transformation toolbar to change the size of object Can modify the size choose whether to lock the aspect ratio and set the position relative to the object to transform 2 9 4 Tilt ASTROK WARE Work Output Doc User Test Transform Apply to copy Apply Object can be tilted by the tilting transformation tools It can be set the tilt anchor and the tilt angle The tilt will cause distortion of the bitmap and the practical application of small currently only supports the tilt vector graphics 2 9 5 Object Array Replication Click Edit Bar r select object wants to copy Then click aa the following dialog box appears Array copy Mum Space 0 000 P p l oo Yum Space c 000 FEE H Width of a single graphic mm I Height of a
24. HourlLHH MM 09 09 12Hour HH MM 09 09 21 24Hour HH MM 09 09 24HourfHH MM 09 09 21 American Date OZ 07 2017 Chinese Date 20i2 Fo2 H07 A Chinese Date Time 2o12reo2 H07 Chinese TirmelOSRT 0944 2180 European Date TimelOFioziz0iza European Date 07 02 2012 fees Year O7 02 2012 09 09 21 s Lile sl ee Oe oe Be Offset Day vo computer time output Software offers a variety of date customers to choose format for Users can also set the date migration have the day by the month according to the years 3 kinds As in carved on the expiration packaging period can use the product ASTROK WARE TrueType font fp Tahoma Width 2 SH Font ay Fs shix Char space Text Line space 9999 Enable variable text Enable prefix ZERO Serialo v Prefix Suffix Start SM 0000 Mumber Space Current SN oo00 J Enable SM array SM Inc E Extend If ABCOOOIDEF processes repeatedly ABC0002DEF ABC003DEF until ABC9999DEF a group of serial number Prefix serial number prefix example ABC is leading string Suffix the seri
25. achine there is space such as dislocation of the seal cutting graphics can be checked 4 9 4 Optical 2 migration In need laser collaborative work complete the same graphics processing occasions usually ASTROK WARE to use the optical 1 to define the graphics location then if the optical 2 can accurately with the optical 1 will need to specify the optical 2 relative to the optical 1 offset This generally used in two power different laser tubes of machine because two of laser tube power different cause different functions If some machines equipped with two different power of laser tube a responsible for cutting a responsible for sculpture 4 10 Layer Settings x Work Mukoue Coc User Test Transform Layer Mode Speed Power Output Cut 100 000 30 000 Yes Cut 200 000 30 000 es Yes Line colurin setup Hum spacelmimn Dislocationimm nH Ao p e v1 e e Gear I es 4 10 1 Ranks se For convenient to set in machining graphics processing on the array X numbers and Y numbers which was the array of columns and rows X intervals and Y interval respectively is array of the column spacing and line spacing Layer Software use layer to distinguish processing graphics parameters of different layers Hy The X interval is said and Y representing between interval graphics margins If hope X interval a
26. al number of the suffix example DEF is the string after Start SN from which a specified number start manufacturing example is to start to 0001 serial number Current SN the current processing to which serial Numbers can also be used to specify the current to processing which serial number As in the processing a group of serial number leakage processing the one but through the designated the current serial number to make processing not set start serial Numbers because in some cases a group of serial number requires repeated processing namely to a serial number need to go back to the start serial number start manufacturing SN Inc the interval number can be prescribed sequence number Example will in turn processing from 0001 to 9999 serial number the increment is 1 If only need to output even or odd number serial number can set incremental is 2 Enable reset when serial number processing to reset the serial number current SN will be automatically reset to start SN Example requires repeated processing from 0001 to 9999 serial Numbers so can be designated 9999 as reset serial Numbers when processing the 9999 serial number text will automatically change to 0001 Enable prefix ZERO if not lead to zero the system will automatically remove the first in the serial number of zero digital before the zero Such as the example serial Numbers if not the leader s zero can ABCO0O01DEF will become ABCI1DEF But
27. d then open ASTRO 7 WARE Look in EI My Documents i Fi EF fe O Adobe Scripts my eBooks Source Insight Baidu My 150 Files Visual Studio 2008 Corel User Files Amy Music Fee FILTERIT4 User Settings Amy Pictures G K5DStore My OO Files amy Designs lt gt File name Files of type rd we Open az read only Software also supports to set the parameters of preview Right click Anywhere in the graphics display area the configuration menu will appears Select Config pop up following dialog box Full window Contizuration Conti ene Background Herazontel mirror Back color W Font color o Vertical mirror Draw colori Power w OT A A too Simulate colori Power w A A oo Idle color es Anchor Top left Top right Bottom left Bottom right You can preview the color of graphics to match the actual output of energy Users can easily view whether the layer energy is true 2 13 10 Data check Selected to check after the graphics click on the menu commands Handle data check or click system toolbar F ASTROK WARE Close check end Check close Not Find unclose curves SelF cross check end Mot Find self cross curves Cross check end Check self crass Mot Find cross curves Overlap check end Nok Find overlap lines _ Auto close Errortrmy 01 Check cross Check overlap
28. e five kinds of method of selecting Click menu Edit gt Select All Shortcuts Ctrl A select all objects Click mouse on the screen to select single object ASTROK 3 WARE Select object using select box Press the mouse and drag as long as the box come into contact with the object will be selected Increased select object minus select object Increase select Press Shift key click or box select to increase select object Minus select Press Shift key click or box select the selected object Select object according to layer HERSH EE ta EE IH 25602 100 000 30 000 EN eE 100 000 30 000 30 000 30 000 D tE 100 000 30 000 lt nT Right click the selected layer then the part of all objects in the layer will be selected 2 8 Object Color The color of object that is the color of the object contour You can click the color button on the Layer Bar to change the color of the object has been selected The color of the pressed button is the color of current layer 2 9 Object Transformation Transformation of object mainly include object location orientation and size But does not change the basic shape of the object and its characteristics Transformation of object for users provides a convenient user interface User can mirror and rotation through 4k Go LZ O within the draw toolbar You can also use the Object Properties toolbar ASTROK 3 WARE x 445 91 enn OY 235 989 m
29. eft Center Middle Right ASTROK 3 WARE Bottom Left Bottom Middle Bottom Right when you intuitive view just look at the zone where the green point appears Absolute Coordinate You can directly check this option when you want the graphics location in the graphics display area correspond to the actual work location of processing Then the graph position will no longer relate with the actual output position of the laser head and orientation point but always regard mechanical origin as the anchor point Small Circle Speed Limit On processing work the software automatically determine whether the current round need to limit speed then according to the diameter size of the circle to determine the speed If parameter configuration appropriate will greatly enhance the quality of small round Click button Add Delete Modify to configuration Small circle is less than speed of the rules limiting the list of small round circle of minimum radius minimum radius circle at the speed of the output of the corresponding If the speed greater than maximum speed limit list the speed round the speed only associated with the speed of the layer If the speed is in the list set the output speed by list If the request received by limiting layer parameters faster than the speed set in the layer press ASTROS WARE the speed of the output layer Scan backlash Laser scanning graphic way because the relationship between the machine belt tension
30. espectively in up down left column the right column initial value and the gradient of the change can form users want to conducting tabula rasa effect For grid way must set exercise can column that can can appear the grid For the convenience of application the system to provide the light setup if the light source is a standard can choose the light source then set the network parameters can be do not need to adjust the baseline At this time baseline shows hides also ASTROK WARE Grid way Elliptic way Left light source Right light source ANY ne eens WLLL WLLL SII SLL SDI SSL TCLS LYN RAAPFP IIOP FIO I FIND I FINED FI ION STIL SS TOES Se ae SS bee wh es wae oa WARING AIK ASTROK WARE Line elliptical rectangular way is the network scanning mode of output LGF cutfEngrave Speedimm si MinFowerf i 30 0 100 0 Default Default MaxPowerl sh 30 0 Li EE J a ma J val Scan precision 1016 dpi OnDelay 0 000 ms OffDelay 0 000 ms Outline cut _ Enable outline cutting speedinm s 00 MinPowert o boo MaxPowerl 1 Boo CrrDelay loco ms Array parameters 0 000 Aum 1 Space Y Num 1 USB Auto i Current Position hgt SavellFile Output UFile Y Space 0 000 Position Scanning mode the minimum energy maximum energy general is same and dedication of the delay is 0 By adjusting the scanning system precisi
31. h Dither Net graphic Frequency iines inch Gat graphic Black 4nd White Gray scale Sharpen Apply bo view Apply to source Get outline In the top right of the dialog box displays the information of the current image Be noted that the horizontal resolution and vertical resolution is changing with drag scaling Apply to view Current settings is only used for preview without affecting to the original bitmap press button Cancel bitmap will returned to the state of original image Therefore only use for adjust effect However this approach requires more time and memory Space Apply to source Current sttings is use for orginal bitmap directly so even finally click button Cancel image will also unable to return to the original image Therefore it mainly used in multi step operation and the current operation of this step is necessary to do such as general pictures must be transformed into grayscale This can save the computing time of the follow up operation Save as Retain the results of the previous operation In addition to using Apply to view can also be exported On this basic to facilitate subsequent processing Gray scale Generally other image processing is based on the grayscale so before handling you can do a grayscale processing then click button Apply to source For the grayscale than the color image occupied smaller memory for large image step by step handle to a certain exten
32. he effects of color image into black and white image is poor however for some clear outline image is very easy to use ASTRO WARE Get outline Kitsap handle LO Lm ZB x width Tetas Pixels Height ea Pixels H Resolution ag Fixelsjinch Y Resolution ab Pixelsfinch Brightness 0 0 rero Zero Contrast Invert color Set output resolution Resolution pixelstinch gt Dither Apply to view Apply to source Get outline Save as FullScreen Click Get outline button to extract the contour graph As following picture ASTROS WARE 2 13 9 Processing preview Click menu Edit gt Preview or click System Bar M 4 E Preview BJA Size Total time Light time Idle interval Work interval kaci at H 4 k ma Power Progress BARAODODODONANIN Default 5 Simulate J Pause Continue Stop Software supports the preview of the documents to be processed and you can get some basic information through the preview For example the path of the actual output of the processing general processing time processing the distance The machining process can be simulated In addition to the current edited file preview you can also preview the files have been saved as rd Preview rd file Double click in the graphics display area Choose the graphic you want to preview in the pop up dialog box An
33. ine Rectangle Click menu Draw gt Rectangle or click Edit Bar LI Drag the mouse on the screen you can draw an arbitrary size rectangle Press the Ctrl key while dragging the mouse to draw square Ellipse Click menu Draw gt Ellipse or click Edit Bar Drag the mouse on the screen you can draw an arbitrary size ellipse Press the Ctrl key while dragging the mouse to draw round Point Click menu Draw gt Ellipse or click Edit Bar Click the mouse on the screen you can draw an point Text Click menu Draw gt Text or click Edit Bar And then in a drawing area any position cli ck pop up text input dialog box ASTRO WARE TrueType Font E Tahoma v SH font Fs SHx Text Width 0 Char space Line space Enable variable text Choose font word input text word then set high wide word spacing line spacing Click again OK The software also supports variable text the so called variable text the text is need according to certain rules change every output processing time text to be automatic change again For the system variables have character type date variables and serial number Variable is the date when the current every time processing take the current system of 2 SHx Font Fs shix Text Width Char space Line space Enable variable text 12
34. m 100 ss A 296 205 mm Gp lena sas mm roo o Mi HH CY o Processnvo 1_ You can also use the right transformation tools to transform and copy the graphics Work Output Doc User Test_ Transform t el Position 2 9 1 Object Image Object image is flip the selected object in the horizontal or vertical direction Click Edit Bar J flip the selected object horizontal Click Edit Bar flip the selected object vertical ASTROK 3 WARE Work Output Dor User Test Transform alle Ratio H i Yi 100 STA Mirror Disproportionate e e E d o d 0 7 Apply to copy Apply Or through the mirror to the transformation tools horizontal and vertical mirror and copy 2 9 2 Object Rotate Click Edit Bar will pop up the dialog of rotate angel setting Set rotate angle and click the button OK Kotate Rotate anglefdeg E Ca cece If you want to drag rotation set rotate angle 0 and determine Dragging the mouse to adjust the rotate angle in the dragging process there will be followed by rotating wire frame outline ASTROS WARE 4 I I K 5 21 mm H 235 989 mm 100 H Y 299 208 mm 208 549 mm 100 i o ProcessNO 1 O Or esi enter the rotation Snes in the or ect Properties toolbar Work Output Doc User l Test Transform q O a Rotate o enter
35. m power no significant difference can be set to give the same To scan processing ordinary scanning the minimum power and the maximum power must be consistent Slope sculpture minimum power loss is the power of the corresponding factors the most power is the power of the bottom of the corresponding top botto Minimum power 1oss 1s tne top tor the small slant wide detail place distinguish clearly Minimum power loss is too large slope not obvious ASTROB WARE To fix processing the minimum power and the maximum power can be set to agree If checked default the actual power panel set by the power to determine Click the button advanced but also can be set to other layer parameters Other layer parameters Ed Enable pen up and down Speedi mmisi Point Dot intervals Extend 10 output j101 Pen up and down If machines have installed the lift platform and need to be in a different platform height on the processing can make can write up function Here the corresponding is platform write position in which high on the processing carried the corresponding is empty pen position before go platform should be moved to which level in the optical translation will not again to interfere with the process workpiece If confirmed the optical not and the translation of the process workpiece to interfere don t need to set up the
36. nd Y interval which between is representative of array center of the graphics spacing can switch to Adjust the X Y interval between enable graphic layout more closely can click drawing area make graphics in the selected state and then through the keyboard of the up and down or so key to adjust and rolling the mouse can be displayed scaling make the spacing of the adjustment process more precise ASTROB WARE Bestrewing breadth According to the size of the wide and the current user Settings ranks spacing to determine how much can output the most listed i e X number how many lines 1 e Y number Click on the button Brestrewing breadth pop up interface as shown in figure Hestrewing breadth Fx breadthimmi Le Y braddth mm 800 According to determine the button the software can automatically calculate the entire width of the ranks of the arrangement number dislocation for some graphics in arrangement the dislocation arrangement can make the arrangement more compact arton ete we Pee 7 2 e r The application to copy in good array chosen to copy graphics some application to copy already can duplicate array graphics In the layer list to edit the double click inside layer namely will pop up layer parameter dialog box The left article color representatives of the current graphics layer choose different color can be in already switch between diffe
37. on to adjust the scanning of the density the more accurately the scanning scan line secret scanning the lower accuracy the scan lines sparse The grid processing methods is cutting and scanning not precision and can be adjusted according to the actual effect the maximum and minimum energy energy light switch delay generally speaking the least energy slightly lower than the maximum energy If need to cut the reflex the outline make can contour cutting About cutting parameters and common cutting Settings identical in hereby here If need to press array in the way processing more panels can be set to array parameters Array direction along the machine is always the origin in the opposite direction ASTROK WARE Chpater 3 System Settings Before output graphics required to determine whether the system settings are correct Click menu Config gt System Setting Configi Handlers System Setting View i File Para Setting Page Setting Password Setting Graph Hatch Show Array Show grid 3 1General settings setting General settings System Info Axis Mirror Laser head d Axis s Mirror O O F A Absolute coordinate Axis Mirror Small circle speed limit Scanningi Reverse interval Diameterimm Speedimm s Speedimmi s Reverse interv Axis Mirror Generally Axis direction of mirror is based on the actual location of the limit or home of
38. osition Current positic 4 1 Search Device Link device in two different ways USB and network But through some equipment port button on the pop up dialog box set connection mode and choose connection port USE Suto Web Default IP If the computer only connected one device you can set to Auto The software will automatically search the device If the computer connected many devices then first of all you need to click Find com After search the connected devices will all add to the drop down list What you need to do is select the specified device Network if the computer is connected only a laser equipment which can be directly in the default IP address to enter in connected device IP When the computer connection has many sets of laser equipment and USB operation is similar Search at present already connected device and choose from the drop down list corresponding IP address machine 4 2 Layer processing First in the menu Handle gt Path optimize check according to layer order then click ORK to exit Layer reorder Click button Up Down can change the order of layers or direct the mouse to drag the layer to the specified location Here you must check the Path optimize option 4 3 Position Setting the laser head back location after processing completed Current position Original ASTROB WARE anchor Machine Zero Current Position
39. osition as center drawing area zoom out once Zoom In Click menu Edit gt ZoomIn or click Each click it the drawing area zoom in once Move mouse to the drawing area and click each click mouse position as center drawing area zoom in once View Select Click menu Edit gt View Select or click 44 Move the mouse to the drawing area hold down the left mouse button and drag a dash border box will show in the drawing area release mouse button then the region in the dash border box will display in the drawing area with the largest proportion View Page Frame Click menu Edit gt View Page Frame or click 4 The page frame will full display View Data Frame Click menu Edit gt View Data Frame or click The selected objects will full display 2 12 Group and UnGroup Edit graphics and sometimes need to be a part of the operation as a whole such as multi line text layout Method Select the group of graphics and then select the menu Edit Group UnGroup or directly select the toolbar g 1 2 13 Important Tool Here are some frequently used tools Using these important tools can make the current ASTROB 3 WARE document in the graphics more orderly and make the processing of output more fast 2 13 1 Manual sorting and the set of cutting point and the cutting direction Software provides users a convenient tool for the manual sorting Select Edit gt Set cutting property
40. out lines select the objects then click Edit gt Edit cut in property or click The following dialog box is appear Cut in and out setting Cut in Enable With angle 4Angle degrees o Cut out Enable LineType iais Female O Male To make cut in cut out lines first of all need to enable the cut in cut out function There are two types of the cut in cut out lines straight line and arc Straight line cut in achieve through three ways Cut in with angle cut in line and starting segment into a certain angle counterclockwise angle is positive Cut in at center the starting point of the cut in line is at center Cut in from center the direction of the cut in line is from center to starting point and length is as setting ASTROB WARE Cut out line The arc length of cut in arc is as setting There are two types of cut in cut out arc as shown in the following figure Female Male The processing of setting cut out lines is same as cut in lines 2 13 3 Path Optimization Path optimization is primarily to re order the vector graphics Click menu Handle gt Cut optimize or click e s the following dialog box is appears Cutting optimize handle Ed Order of layer Inside to outside Single inner to outer wt Block handle Height Dir Up to bott F Start poink optimize Auto determine start point and direction ASTRO 7 WARE Click menu Edit gt Show Pa
41. priate to reduce the turning speed Turning Acc Should match with the turning velocity Cutting mode Split precision cutting fast cutting ultra fast cutting the user can choose according to the actual applications Such as the emphasis on accuracy select the precision cutting such as emphasizing speed select the fast cutting Acce mode this parameter decides the acceleration and deceleration mode S mode or T mode of the motor during operation the motor accelerates and decelerates slowly and smoothly in the S mode and fast and relatively unsmooth in the T mode the default mode is the S mode 3 3 2 Sweep parameters Sweep parameters x Start Speedimmis 20 000 y Start Speedimmis 15 000 x Acctmmiys2 2000 000 y Accimmiys2 000 000 Line Shift Speed fmm 150 000 Scan Mode Common Mode Facula Size S0 99 1 98 000 x Start Speed y Start Speed Off scanning speed in the use of stepper motor drag do not began to accelerate from 0 but can start work directly from a speed to shorten the overall processing time but the speed is not too high and because the X Y axial load is different from the ASTROB WARE rate general the initial speed of X axis slightly higher than the initial speed of Y axis x Acc y Acc With the scanning speed the speed of layers in the layer parameters to match if set too small the scan speed to a longer distance the scanning efficiency The machine can be set according to the actual structure
42. rding to the actual graphics gray in output already color deep place laser energy big color shallow place laser Energy is small Figure yuan respectively output for vector graphics for figure yuan respectively according to vector diagram output is the position of the yuan relationship which in turn will get together the vector map carving output of yuan respectively If not checked figure yuan respectively output it will be the whole vector graphics as a whole to sculpture For a bitmap for if not checked figure yuan respectively output the system will automatically ASTROB WARE will work with a layer of the bitmap in as a whole output If checked the figure yuan respectively output the system will be in a single output bitmap Slope effect the scan the edges of the figure appear slope submit stereo effect Be bold font including don t handle scanning the font scanning the bottom Generally choose not processing Scanning is part of the font scanning is the font also 1s the Yin carving Note that the slope effect choice please will be bold font choose not to deal with or slope affected the effects Font Yin carved not to add text outside the box scanning are text itself as below IK AE FA Font Yang carved text and the outer frame scanning is the bottom of the graphics as below Wr 30 E A XK 1 HH Scanning mode including level one level two way vertical one way vertical two way Level one way the optical scan pat
43. rent layer one time modified multiple layers of parameters The layer parameters is divided into two parts public layer parameters and turn a layer parameters Public layer parameters is to point to no matter how the layer processing type all effective layer parameters Proprietary layer parameters is to point to the layer of processing type change of the corresponding parameters will also be changing ASTROS WARE Layer Parameter Load parameters From library aver Is Output WE 7 Speedimmysi 400 C Defaut IF Blowing ves Processing Mode Cut Min Power Max Powerl Laser1 30 Default Laser Seal Open Delay ms Close Delay ms Laser through mode 4 10 2 Laser Scan Parameters Setting IF Blowing Processing Mode Min Powerl Maxs Power aver M Is Output Speedimmis 400 Default _ Advance fo Laser Laser aj 30 Default Laser Software to distinguish between different layers of the graphics processing technology parameters For scanning processing methods
44. rigin Delay before feedis 0 000 Dealy after feedims 0 000 Focus depthimm 0 000 Backlash ror 0 000 Backlash imm 0 000 Array mode you can choose the swing mode and the one way mode The Swing mode cutting the array back and forth in order the One way mode always cutting the array from one direction to another If One way mode is selected all array units have the same movement modes and the same liquidity of movement however this mode will take more time than the swing mode The default mode is the Swing mode Return position You can select the locating point and the machine origin This parameter decides the position the locating point or the machine origin where the laser head stops upon completion of each operation Delay before feed Using the feeding device the delay before a single feed users can arrange the time and the like such as picking process Delay after feed Refers to the material sent to the feed device in place the need for stability after a period of time for processing Focus depth Auto focus operation to find the corresponding panel Backlash X Y Used to compensate the backlash caused by the machine drive problems 3 4 Document Management ASTROK 3 WARE Work Output Doc User Test Transform Mumber File Mame Time H M 5 M5 Read Click button Read the software will communications with the controller read the list of files on the controller After read controller successful file info
45. rmation will be displayed in the document list Download Click button Download will pop up the file dialog select rd downloaded file then the file will be downloaded to the controller If the download is successful the document list will update Process Select the file to be processed from the document list and click button Process The controller will start the specified document Delete Select the file you want to delete from the document list and click button Delete The controller will delete the specified document If the deletion is successful the document list will be updated Delete All Automatically remove all file in the controller and update the document list ASTROB WARE Cal time Motherboard supports processing files towards hours worked Select the file to calculate the work hours worked and click the button Calculation to be completed the control panel will be prompted to complete the calculation And then point to read button shown in the list calculated from the working hours In addition when the document processing operation performed the hours information will also be covered by the actual processing work uploading On the main board of the selected from read offline files and saved to the computer Chapter 4 Processing Output ASTROB WARE x Laser work Processing control SaveTOUFile UFileGutput ae Layer settings E USE Auko Search device i tI cD cu P
46. rmentiS Element1 Elementi Element1 Element19 Element20 Element 1 Element22 Element23 Element24 Elementz5 Elementz6 Element Elementz8 Elementz9 Element30 il ShowPath xY Select the graphics that should be changed the cutting point it will show all the nodes in the current graphics Select the starting point double click the mouse it will change the starting point of the current graphics After the completion of all changes click the result of the changes can be saved In addition to cutting property features the software also offers some tools to change the cutting order cutting direction and cutting point Select L in the toolbar or click the menu command Edit gt Show Path ASTROK 3 WARE Default RD5 0 0 9 File E Edit E Draw D Config S Handle W View V Help H Deh ARG ea CRQRRR OT a mw O a i eG B gt i 100_ i m ies a oe i 2000 3000 4000 5000 6000 7000 8000 9000 i 10000 lt Xx I I Ii I re Work Output Doc User Test Transform 10 p Chaar Xs S 00 NNA Layer Mode Speed Power Output cut 100 000 30 000 Yes 00 0 Liia al 000 lt D Device Laser work Position Current positic SaveToUFile UFileOutput C Output select graphics Path optimize 000 BaAwoe Ss HT SDA RANY ORE SEE on E Welcome to use the Laser system of cutting Propose the display area 102
47. row key to moving or rotating the selected graphics Color config Setting the color of the work area 2 4 File Open and Save The software uses rld file format to save graphic information layer parameters of various layers and processing sequence of the graphic elements 2 4 1 Open File Click menu File gt Open or click iconla the following dialog box appears SSR CL coo EARE Ds Select file WA Default rld TFE T orld xl Ne ELA ASUTT F R 2 Select file e g Default rld click Open 2 4 2 Save File 1 Click menu File gt Save or click iconkgl the following dialog box appears ASTROK WARE ls Default rld Input file name TA H Default rld IF E FITE I ELaser Files rld Y Hpi 2 Enter the file name in the edit box then click Save 2 5 File Import and Export Because this software is rld format so to make or edit the use of other materials will be done by importing After using the Export to graphic files for other software Supported file format for import dxf a1 plt dst dsb etc Supported file format for export plt 2 5 1 File Import Click menu File gt Import or click icon gl The following dialog box appears Select file and click Open Sie gt PLT 7 amp u 0000033 plt bu 24 plt BTE plt bo BRIEF plt E plt bu HIE plt bul 4 plt bo HEIL plt bu R plt fi Airplane p1t bo RE plt b
48. rror Close error mm Force to close Close error When distance from the starting point to ending point less than close tolerance automatic closing of the curve Force to close Mandatory closure of all selected curves ASTROB WARE 2 13 6 Remove The Overlap Click menu Handle gt Delete overlap or click the dialog box appear Delete overlap lines Enable Overlap error Overlap errortnrrn ooo Under normal circumstances do not select the Enable Overlap error Removing the overlapping lines when two lines are compared to a good degree of coincidence If you need to delete overlapping lines you should select Enable Overlap error and set overlap error Generally do not overlap error set too large so as to avoid accidental deletion 2 13 7 Combine Curve Click menu Handle Combine Curve or click 94 the following dialog box appears setting combine error x Combine errorimm The software automatically merge curves in the selected curves when these curves merge tolerance is less than the setting of combine error 2 13 8 Bitmap Handle Click r and select a bitmap then click menu Handle gt Bitmap handle or click System Bar EMF ASTRO 7 WARE width Fixels Height 750 Pixels H Resolution 36 Pixelstinch Y Resolution 36 Pixelsfinch Brightness Contrast O 0 n Invert color Set output resolution Resolution pixelsfinc
49. selected 4 7 Path optimize After check Path Optimize then automatically perform the path optimize before the output If has done the Path optimize or not need optimize then not check Path Optimize can reduce waiting time RuiDa ACS 4 8 Test Axis control can only control one axis each time You can set the information for axis move ASTROS WARE work Output Doc User Test Transform Current Position Axis Move OfFfsekimm sJ fl Speedimmi s e mes gt Move From origin IF Light including move length speed laser on off and laser power If you check Move from If you not check move from origin then the offset means the offset to the current position The X axis for example to 10mm then the exercise once the new location will be 110mm such as the check moves from the origin movement time the new location will be 10mm and repeated Movement location will no longer change Note According to the provisions of the controller the absolute position is no negative in the whole breadth If you check the Move From Origin and set the offset value negative then the machine will hit limiter 4 9 Output Setting origin then the offset you set means the offset to machine zero assuming the current position is 100mm such as the step distance is set ASTROK WARE work Output Doc User Test Transform _ Enable rotate engrave Circle pulse Diame
50. t to avoid the lack of memory For color image adjust contrast and brightness have some auxiliary effect to following dither processing Adjust contrast ASTROS WARE Invert Before processing After processing Sharp Before processing After processing ASTROB WARE There are three method for dither processing Net graphic Dot graphic Black and white Net graphic Net graphic need adjust net size better suited to material which is not high resolution or the laser is relatively slow to respond To get the appropriate net size you can adjust resolution and net frequency of the image The higher resolution the more delicate The higher net frequency the smaller net size The lower net frequency the bigger net size Generally resolution of image is 500 1000 and net frequency is 30 40lines Teh ims pr oe e emnene a n mse mns aia na nia s Sak gage a aa a a ta a a a a is is aga Marata at a ee a Maa aat aan M an e Mata at A a BT Ma a Ma at Ma a Ma at aa S aa a aia i MP te iat ake aa a a h a h a ae ae Dn be Pe ae oe alta al a MN aata at Ta aata aata at Ta at a aT Ta aTa a E 7 a x ii titg aa MEF aSa RF afa Mat afa a a Ma a Ma aa aha Sah a a ae te ome ome mmm nsmi nmn eR panes cest cls ca Pon saat she a GPa ann Mel Dot graphic Dot graphic performance of good grayscale better suited to material which is high resolution and the laser responds fast Black and white In most cases t
51. ter Ed beset smoothing effect you can uncheck this button Do Import Setting not do smoothing curves may reduce time of import PLT Precision processing DXF Unit Import Dxf text info Auto close curves According to close tolerance C Smooth curves automatic check and closed curve Auto close curves Close errorimm Combine lines According to merger tolerance auto Combine lines Combine errortram connecting Curves Export Setting E Color map automatically switch to grayscale Because under normal circumstances graphics are based on velocity Unit mms grayscale If the imported bitmap is a color image can be converted to grayscale Import Dxf text message When the user need only Dxf the graphic information not need the ASTROK WARE text information within the file do not check this Export precision The precision of export plt file or output file Velocity unit Software supported two types of speed unit mm s m min Selected according to usage After it was selected the speed of parameters on the interface unit will change with it 2 6 Basic graphics creation Line Click menu Draw gt Line or click Edit Bar drag the mouse on the screen you can draw an arbitrary line Press the Ctrl key while dragging the mouse to draw horizontal or vertical line Polyline Click menu Draw gt Polyline or click Edit Bar Drag the mouse on the screen you can draw an arbitrary polyl
52. tern back and forth in a horizontal direction but only to a direction when laser scanning comes out Such as when the optical scan from right to left a laser and from left to right the laser scan Level two way the optical horizontal direction in the back and forth laser scanning graphics The vertical one way the optical scan pattern in vertical direction back and forth but only to a direction will be laser scanning Such as when the optical scan from up to down a laser and from the bottom to scan a laser The vertical two way in vertical direction the optical back and forth laser scanning graphics Note general use level two way scanning mode Scanning interval namely the optical scan every much long distance under a line The smaller the interval scanning the deeper to graphics Conversely the more shallow Suggestions 1 for vector layer i e color layer scanning interval in 0 1 mm general set below 2 for a tutu layer namely BMP layer scanning interval in 0 1 mm general set above Then through the change and the most high power to make the minimum power after scanning the graphics depth to achieve the ideal effect ASTROB 3 WARE 4 10 4 Laser Cut Parameters Setting Layer Parameter Eg Load parameters from library ayer M Is Qubpuk HEE Y Seal cutting has not closed the graphics Speedimmj s 100 Default appear the case is closed you can If Blowing Yes P compensate with the seal to close b
53. tertmm Speedimmnysi Enable Feeding Feeding Count Diskancetram Backlash reapy optimize Enable offset of Laser eE E_ 4 9 1 Rotating sculpture Enable rotate engrave After enable engraving the actual precision of Y axis will be based on diameter and step per rotate to auto match the setting of pulse precision of Y axis In addition the work area in the main interface will also change Diameter The diameter size of the parts Step per rotate The number of pulse corresponds to the workpiece rotate one week speed test the speed of work The function is to facilitate the users to replace parts and different size of the workpiece when the workpiece is not very different before use When the relatively large difference in size of the workpiece it is recommended to use directly modify the motor step approach to implementation Rotary engraving 1s only when using the rotation axis to replace the Y axis use 4 9 2 Feed Setting To use the feed must first enable the feed After set feeding parameters the shaft will be feeding a feeding length and repeat the process until the times of processing reach to number of feeding If the machine is not equipped with feeding devices in general enable the feed ban 4 9 3 Optimization of Backlash Compensation When the m
54. th or click E can see the cutting path before and after FRRIT SIG PRN ESERE E SEREA HT DE AFERRA E T Rae pinnt UELL TAAA t Before processing After processing Graphics cutting path is always starting from the laser head 2 13 4 Curve Smooth For some less accuracy curves this function can make curves more smoothness and processing smoother Click menu Handle gt Curve Smooth or click the following dialog box appears Curves smooth J 95 Direct smooth Smoothness ES ee Eee Drag the smooth slider and click button Apply before smooth and after smooth curves will all ASTROK WARE show in the dialog The black curves represent the original curves and the red curves represent after smooth curves Curves smooth Smoothness 95 Direct smooth EE Ee ee You can view the graphics with drag mouse You can zoom in zoom out the graphics with scroll wheel Click button FullFrame graphics will shown in the dialog box for largest After get satisfied smoothing effect click button Apply curves will processing smooth according to smoothness settings Select Direct smooth you can use another smoothing method The choice of smoothing method should be changed with the needs of the actual graphic 2 13 5 Check Closure Click menu Handle gt Curve auto close or click System Bar _ the following dialog box appears Setting close e
55. u Alphabet plt bu S plt bu AOP plt bu FERETE plt bu Beach plt lor HE plt p Box and Curve plt bul E1 plt bul Box plt bal FFE 22323 plt ju Business plt bu FBSA 2 plt bu Circle plt bu 8 plt bu CONGER plt bo TAMH E plt u Curve plt b HE plt bul gemm plt bul 4s plt lu job 2 plt bu DER plt bu shoe12 plt bu plt bu FEAR plt bo plt V Preview mohina S TFW T Supported Filesi Select Preview the selected file can be shown For most vector file data automatically imported into the corresponding layer of RDCAM software according to the layer description For some special documents such as DST DSB data will be imported into the current layer ASTROB 3 WARE SHET gt pst maa E Ls045 DST E LS066 DST E Lx215 DST MISO DST E PORSCHEZ DST E SUNFLOWR DST E VERONIKA DST V Preview TFA N fAhudiel DST TFW T Supported Filesi Current layer 2 5 2 File export Click menu File gt Export or click icon Hf The Export dialog box appears Input file name and click button Save 2 5 3 File parameters setting PLT Precision According to the accuracy of the original plt file to select the appropriate import unit Smooth curves When import vector file automatically smoothing the original curves For the original graphic is smooth or need to repeatedly adjust the File Parame
56. ut if the seal is misplaced you can not Processing Mode ut compensate you can use 4 9 5 optimization backlash compensation to compensate or to use the user parameter in the Backlash compensation Min Power Max Powerl Laseri 30 30 Defaut Laser Open delay Open Delay FF 0 Ea E Close delay Laser through mode If checked the light switch delay is playin g in time said Otherwise the light switch delay said is la ser movement delay Using the slit width compensation can compensate for the offset between the graphics and the actual output graphics that caused by laser cutting It only has effective for the closed graph Direction Compensation direction is set according to actual needs such as cutting a circle if you want to retain the cutting down of the circle you should set out the direction of compensation If you want to keep the hole should be set to compensate for the inward direction Sew width it is the width of the laser Other cutting param _ Enable sew compensation Direction Ser width jor mm ASTROK 3 WARE 4 10 4 Laser Dot Parameters Setting Layer Parameter Eg Layer E Is Output Yes Speedimmniy s Default IF Blowing Yes Processing Mode Bot oP Min p a Max z The time for emitting laser on
57. ypes About RECAM EE Language 6000 TOO0 To obtain manufacturers information so that we can provide you with better service Click Menu Bar Help gt About RDCAM comp Names E O O ports po pd How to set manufacturers refer to RDCAM software installation instructions The bottom of the dialog box shows the current software version number As different versions of software may be have some differences on the functions and interfaces you can easily contact and communicate with manufacturers through software version number 2 3 Page Setting Click Menu Bar Config gt Page setting the following dialog box appears ASTROB WARE Page width Software page width usually associated with machine X breadth Page height Software page height usually associated with machine Y breadth Under normal circumstances if you have connected to the Page setting Page size Page width Metall Page height soo motherboard software will automatically format for the an current work of the machine as a page size GridSpace 50 If the board is not connected or need their own custom Keyboard page size such as to set the page size by material you can Adust distance 1 use the page setting to reconfigure the page size Adjust ratio Grid Adust angle Setting gird space and whether enable grid Color config Background work area Keyboard Grid User can use ar

User's Manual of

Contents

Download Pdf Manuals

Related Search

Related Contents