INSTALLATION AND OPERATION MANUAL
Contents
1. PRIME ce CF INSTALLATION AND OPERATION MANUAL TBD GA 6000DL LIGHT BAR A WARNING The lives of people depend on your safe installation It is important to read and follow all instruction shipped with the products In addition listed beloware some other important safety instructions and precautions you should follow A WARNING 1 The vehicle speed limit is 120 kilometers per hour 2 Strickly following the Installation and Operation Manual SPECIFICATIONS Input Voltage 12VDC Input Current 18 5 AMPS Output Voltage Maximum 222W Input Voltage 24VDC Input Current 9AMPS Output Voltage Maximum 222W PARTS LIST HOOK 2 PCS SHIM 8 PCS SCREW 2 PCS CAP SCREW 2 PCS HOOK MOUNTING 2 PCS ADJUSTMENT BOLT 2 PCS BEFORE INSTALLATION To properly install a light bar you must have a good understanding of automotive electrical procedures and systems along with proficiency in the instruction and service of safety warning equipment e When drilling into a vehicle structure be sure that both sides of the surface are clear of anything that could be damaged e You should frequently inspect the light system to ensure that it is operating properly and that it is securely attached to the vehicle Refer to the instruction sheets packed with related products for additional precautions and information e File these instructions in a safe place2. and refer to them when maintaining and or re installing the product Failure to follow all safety precautions and instructions may result in property damage serious injury or death to you or others DURING INSTALLATION e Do not connect this system to the vehicle battery until all other electrical connections are made mo unting of all components is complete and you have verified That no short exist e Installation of this hook kit requires the use of parts from the mounting system kit WIRING DIAGRAM HOOK MOUNTING LAMP CONTROLLER gore Figure 3 _ BLACK YELLO SH RED ooo LZ H RED LED RAY x ii 71 LAMP e AEN REVOLVING lt LAMP hd Figure 4 AFTER INSTALLATION After joining according to the above Figure 3 wrong to check and install Itis correct to confirm And then put through the power push the light on the controller and accuse of the switch checks considerably the lamps and lanterns are at this moment Deny the normai work ea eo Figure 1 INSIDE STRUCTURE INSTALLATION Place the lightbar assembly on the vehicle roof at the desired location Usually the unit should be installed
3. approximately over the driver s head Refer to the instructions included with the mounting system kit for additional information Water may leak into the vehicle interior if the hook is improperly positioned Ensure that the hook is CAUTION positioned above or near the center door post ae i Ray Light Control Module Place the hook in position on the roof sheet metal Revolving Light e LED Light as shown in figure 1 R otto tteaee Seneca ereasieteaeteeeed Figure 2 A WARNING The use of this or any warning device does not insure that all drivers can or will observe or react to an emergency warning signal Never take the right of way for granted Itis your responsibility to be sure you can proceed safely before entering an intersection driving against traffic responding at a high rate of speed or walking on or around traffic lanes The effectiveness of this warning device is highly dependent upon correct mounting and wiring Read and follow the manufacturer s instructions before installing or using this device The vehicle operator should insure daily that all features of the device operate correctly In use the vehicle operator should insure the projection of the warning signal is not blocked by vehicle components i e open trunks or compartment doors people vehicles or other obstructions This equipment is intended for use by authorized personnel only It is the user s responsibillty to understand an
4. d obey all laws regarding emergency warning devices The user should check all applicable city state and federal laws and regulations Pubic Safety Equipment Inc assumes no liability for any loss resulting from the use of this warning device Proper installation is vital to the performance of this warning device and the safe operation of the emergency vehicle It is important to recognize that the operator of the emergency vehcle is under psychological and physilolgical stress caused by the emergency situation The warning device should be installed in such a manner as to A Not reduce the output performance of the system B Place the controls within convenient reach of the operator so that he can operate the system without losing eye contact with the roadway Emergency warning devices often require high electrical voltages and or currents Properly protect and use caution around live electrical connections Grounding or shorting of electrical connections can cause high current arcing which can cause personal injury and or severe vehicle damage including fire
Download Pdf Manuals
Related Search