Installation manual - Becker
Contents
1. If the drive produces a loud noise and the tube does not turn the drive is a type M Replace the program ming unit immediately with one that is suitable for an M drive If the drive does not react or if it clicks once or twice it is an S PS SEB SF or PSF drive Press the travel button to move in both directions If the drive does not react it is a drive with integrated radio receiver of type SF up to 2002 or type PSF from 2003 onwards Travel the curtain downwards and press the program ming button again for 2 seconds If the drive does not react or if it clicks once start retracting the curtain until the drive stops at the limit position stop or ata pre programmed switch off point If the drive clicks twice press the programming button again until the drive clicks once Then retract the curtain until the drive stops at the limit position stop or at a pre programmed switch off point Both limit positions are now programmed in the drive Press the programming button again for 2 seconds If the drive clicks twice itis a type S up to 2003 If the drive does not react it is a type PS or SEB Carry out the procedure for deleting Press the programming button and keep it pressed Press the button and keep it pressed Release the programming button Press the programming button again until the drive clicks twice Press the programming button O for 2 seconds twice2. Important safety instructions for handling tubular drives e Do not allow children to play with control units e When electrical or electronic equipment and units are operated certain components e g the power supply unit are live Physical injuries or damage to property can result in the event of unauthorised interventions or failure to heed warnings e All work including maintenance and cleaning on electrical installations as well as other sys tem parts must always be performed by authorised specialists especially qualified electricians Before installation shut down all lines and control devices that are not essential for operation e If the mains connecting cable is damaged it may only be replaced by the manufacturer e When installing the drive all pole disconnection from the mains with a contact gap of at least 3mm per pole must be provided EN 60335 e Stop and disconnect the equipment from the mains power supply when maintenance and cleaning is being performed either on the system itself or in the immediate vicinity of it Drives with a HO5VV F connecting cable may only be used indoors All applicable standards and regulations for electrical installation must be complied with Systems have to be regularly checked by authorised specialists for wear and damage e Always put damaged systems out of operation immediately until they are repaired by an authorised specialist e Do not operate equipment if people or o
3. consecutively If the drive clicks Once and then twice it is a type SEB from 2003 onwards If the drive clicks only once it is a type PS from 2003 onwards gt BECKER M drives Type plate for the M drive Type designation e g R 8 17 C M R size of drive tube diameter P 35mm R 45mm L 58mm 8 17 rated torque output speed C pluggable connecting cable M mechanical limit switch Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 08 40 961630 08 year 2008 40 calendar week 961630 consecutive number Connecting M drives Drives with mechanical limit switching must not be connected in parallel to a control section A discharge of the capacitor could damage the limit switch This would cause the limit positions to be overrun The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous RETRACT and EXTEND commands BECKER CE eq AGS P44 GD RKB 4 in Ser Nr 0840961630 Made in Germany Drive 1 Drive 2 Information on the M drive Before installation make sure that the drive adapter safety catch has engaged is screwed on Mark the position of the drive adapter on the tube and drill a 4 mm hole at this point Secure the drive adapter against axial displacem
4. the pow er supply at the radio controlled receiver radio controlled drive or external Centronic radio controlled receiver or set the radio switch of the radio controlled drive to or press the radio programming button of the external Centronic radio receiver O Subsequently press the pro gramming button at the master transmitter to be programmed for ten seconds until the radio controlled drive clicks twice or the external radio controlled recei ver confirms programming slight movement twice Programming other transmitters Press the programming button at the master transmitter or three seconds until the radio controlled drive clicks once or the external radio controlled receiver moves slightly Subsequently press the program ming button at the transmitter to be programmed for three seconds until the radio controlled drive clicks once or the external radio controlled receiver moves slightly Subsequently press the pro gramming button again at the transmitter to be program med for three seconds until the radio controlled drive clicks twice or the external radio controlled re ceiver confirms programming slight movement twice x click eja a O A click BECKER Radio technology Deleting the transmitters Deleting transmitters 1x click a individually ajb ejaje Press the programming button at the mas
5. PS Art Nr 2030 130 131 0 M 30Nmin 17 mi U 230 V f 50 Hz U o1 Ser Nr 0901961657 Made in Germany Drive 2 ANGS 1P44 BECKER KB 4 min 3 Information on the PS drive PS drives with electronic limit swit ching detect and program the closing li mit position automatically if a permanent stop exists If no stop exists a limit switch point is programmed PS drives PS drives are used to operate screens awnings and conservatory shading PS drives PS drives are used to operate casset te awnings that require a higher closing torque The cassette is then always closed completely The limit positions can be set using the programming unit or the switch on the drive head Connect the wires in the connecting cable of the drive to the wires of the same colour in the programming unit AA 62 BECKER PS drives Setting the limit positions via the switches of type PS 1 Delete both limit positions with the switches Set both switches to O and execute a short drive command 2 Programming the exten ding limit position Travel the curtain to the desired position and switch the correspon ding switch from Otol 3 Programming the retrac ting limit position Q Retracting limit position stop Travel the curtain towards the stop until the drive stops automatically Retracting limit position point Travel the curtain to the desired
6. automatically 3 Deleting the limit positions g 2x click using the programming unit 5 Press the programming button on the programming unit until the drive clicks twice 62 BECKER PS drives Type plate for PS drives Type designation e g R 30 17 C PS R size of drive tube diameter P 35mm R 45mm L 58mm 30 17 rated torque output speed C pluggable connecting cable P point to point programming possible S electronic limit switching for sun protection F higher closing force for cassette awnings Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 09 01 961657 09 year 2009 01 calendar week 961657 consecutive number Connecting PS drives Several drives with electronic limit switching can be connected in parallel to a control section The maximum number of synchro nously controlled drives depends on the load capacity of the operator control The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous RETRACT and EXTEND commands The following applies to operator controls with a 5A contact load rating R5 20 PS R12 17 C PS max 5 drives R20 17 C PS R60 17 C PS max 3 drives R70 17 C PS R120 11 C PS max 2 drives Drive 1 CE C R 30 17 C
7. illuminate all the receivers in which the transmitter has been programmed are activated Example 7 _ oe es Channel 1 Individual transmitter A master transmitter controls drive 1 Channel 2 Individual transmitter B master transmitter controls drive 2 Channel 3 Individual transmitter C master transmitter controls drive 3 Channel 4 Group transmitter d controls drive 1 and drive 2 Channel 5 Group transmitter e controls drive 2 and drive 3 Channel 6 The central transmitter all group LEDs illuminate controls drive 1 drive 2 and drive 3 2 BECKER Radio technology Programming the transmitters Programming the master transmitter Switch on Power On the pow er supply at the radio controlled receiver radio controlled drive or external Centronic radio controlled receiver or setthe radio switch of the radio controlled drive to or press the radio programming button of the external Centronic radio receiver O Subsequently press the program ming button at the transmitter for three seconds until the radio controlled drives clicks twice or the external radio controlled receiver confirms programming slight movement twice Overwriting the master transmitter When programming a new master transmitter the old one is overwrit ten All other programmed functions at the receiver remain unaffected Switch on Power On
8. limit position An automatic reversal function in the extending limit position ensures that the fabric is stretched o_o eee ee a SE B drives SE B drives are used to operate screens E Fi awnings and conservatory shading Le Q SE B drives SE B drives are used to operate cassette awnings that require a higher closing torque The cassette is then al ways closed completely The limit positions can be set via the programming unit amp BECKER a a gt Connect the wires in the connecting cable of the drive to the wires of the same colour in the programming unit c5 62 BECKER SE B drives Programming the limit positions with the programming unit of type SE B 1 Programming the exten ding limit position with the programming unit Connect the wires of the tubular drive to those of the same colour in the programming unit Travel the curtain to the desired po sition and press the programming button until the drive clicks once Note If the drive clicks twice an extending limit position had already been saved which has now been deleted In this case press the programming button again until you hear one click 2 Programming the retrac ting limit position via the programming unit Travel the curtain towards the upper stop until the drive stops automatically 1x click gt 3 Deleting the limit positions using the programming unit Press the progra
9. position and change the corres ponding switch from Otol Programming the limit positions via the programming unit of type PS 1 Programming the exten ding limit position with the programming unit Connect the wires in the connec ting cables of the drive to the wires of the same colour in the Becker programming unit At least one switch on the drive head must be in position l Travel the curtain to the desired position and press the programming button until the drive clicks once 2 Programming the retrac ting limit position with the programming unit Retracting limit position stop Travel the curtain towards the stop until the drive stops automatically Retracting limit position point Travel the curtain to the desi red upper position and press the programming button on the programming unit until the drive clicks once 3 Deleting the limit positions using the programming unit Press the programming button and keep it pressed Press the button and keep it pressed Release the programming button Press the programming button again until the drive clicks twice If the drive is situated between the limit positions both limit positions are deleted If the drive is situated in one of the limit positions only this position will be deleted x olick 4 62 BECKER SE B drives Type plate for SE B drives Type designation e g R 40 17 SE B R size of drive
10. tube diameter R 45mm L 58mm 40 17 rated torque output speed S electronic limit switching for sun protection E B automatic fabric stretching in the extending limit position higher closing torque for cassette awnings Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 08 50 20130 08 year 2008 50 calendar week 20130 consecutive number Connecting SE B drives Several drives with electronic limit switching can be connected in parallel to a control section The maximum number of synchro nously controlled drives depends on the load capacity of the operator control The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous RETRACT and EXTEND commands The following applies to operator controls with a 5A contact load rating R20 17 SE B R60 17 SE B max 3 drives R70 17 SE B R120 11 SE B max 2 drives Drive 1 BECKER CE eq AGS P44 GD R 40 17 SE B Art Nr 2040 030 119 0 M 40Nm n 17 min U23230 V IKB 4 min C Ser Nr 085020130 j v o1 Made in Germany Drive 2 Information on the SE B drive SE B drives with electronic limit switching detect and program the closing limit position automatically A fixed stop must be available for the retracting
11. waiting for 15 seconds Q l i press the programming knob until after Uv 6 seconds the LED changes from green to orange and back to green 62 BECKER Controls Radio technology Principle Design of the individual group and central controls Each radio controlled receiver provides one storage space for the master transmit ter and 15 storage spaces for other transmitters Master transmitter 15 other transmitters asm amd ima mest a a a APOE ee eee eee eee The master transmitter is programmed into the receiver via the radio programming button the radio switch or via Power ON All other transmitters are programmed into the receiver with the help of the master transmitter It is possible to create a group or central transmitter by programming one transmitter to several drives Example Becker becker pecker pecker pecker a a a a a a m m m m m m W W W W v g Individual master Group Central Individual transmitter A master transmitter controls drive 1 Individual transmitter B master transmitter controls drive 2 Individual transmitter C master transmitter controls drive 3 Group transmitter d controls drive 1 and drive 2 Group transmitter e controls drive 2 and drive 3 Central transmitter f controls drive 1 drive 2 and drive 3 With a 5 channel transmitter each individual channel acts as a separate transmitter When selecting all the channels all group LEDs
12. 2 17 S max 5 drives R20 17 S R60 17 S max 3 drives R70 17 S R120 11 S max 2 drives BECKER KER KER CEA py R20 17S Made in Germany Drive 1 Art Nr Drive 2 f 2020 030 008 0 o eame Ser Nr 054850572 Information on the S drive S drives with electronic limit switching detect and program the closing limit position automatically if a permanent stop exists S drives S drives are used to operate screens awnings and conservatory shading aE E 1 LAA RRA RRA RAR A SE S drives S drives are used to operate casset te awnings that require a higher closing torque The cassette is then always closed completely The limit positions can be set via the programming unit Connect the wires in the connecting cable of the drive to the wires of the same colour in the programming unit gt BECKER S drives Programming the limit positions with the program ming unit of type S 1 Programming the exten ding limit position via the programming unit Connect the wires in the connecting cables of the drive to the wires of the same colour in the Becker program ming unit Travel the curtain to the desired position and press the programming button until the drive clicks once 2 Programming the retrac ting limit position via the programming unit Travel the curtain towards the upper stop until the drive stops
13. Installation manual Drives and controls for Roller Shutter and Sun Protection Edition 10 2010 BECKER Its that Preface Using the installation manual The installation manual describes the commissioning of Becker tu bular drives for roller shutters and sun protection as well as the com missioning of specific Becker controls This manual is intended for technicians who have been trained by Becker Antriebe GmbH It is essential that you follow the safety instructions for the installation and commissioning of tubular drives and controls on pages IV V at the end of the installation manual Disregarding them can result in serious injuries The installation manual does not replace the Assembly and Opera ting Instructions supplied with Becker products Always observe the information in the installation manual as well as the Assembly and Operating Instructions supplied with the product when operating or repairing the system Becker Antriebe does not accept liability for damages or injury resulting from incorrect usage Subject to technical changes without notice Contents How to identify the type of drive M drives PicoR drives R drives RP drives PR drives PRF drives PROF drives SC431 II control unit How to identify the type of drive M drives S drives PS drives SE B drives PSF drives SWS241 control set SWS441 SWS641 control set SC211 control Princip
14. a row three opening and closing procedures the drive saves the limit positions 62 BECKER Commissioning of the radio controlled light sensor C431 ll Programming the C4931 II 1 Press the programming button on the right hand side of the master transmitter the transmitter that was programmed first until the receiver clicks once Master transmitter 2 Now press the programming button of the SC431 Il until the receiver clicks once PIA ne 3 Now press the programming button of the SC431 II again until the receiver clicks twice Ml Setting the sun protection 1 By rotating the sun threshold regulator you can adjust the sun threshold value with the help of the indicator lamp Setting the twilight function 2 By rotating the twilight threshold regulator you can adjust the twilight threshold value with the help of the indicator lamp Manual Auto button Press the manual auto button to switch the automatic commands sun protec tion and twilight function on off Glass break function Press the button until the display LED illuminates green The glass break function is now active Press the button again to deactivate the glass break function The display LED illuminates red O N Ee cq eas eo eo ed YO cq c ca S LED green LED red LED flashes Sun protection Sun protection yellow function being function not Rotary switch executed being execu setto0
15. bjects are within the danger zone e Observe the danger zone of the equipment during operation Ensure that there is adequate clearance at least 40 cm between moving parts and adjacent objects e Crushing or shearing points must be avoided or protected e Observe safety clearances in accordance with DIN EN 294 e Observe the safety instructions in EN 60335 2 97 Please note that this list of safety instructions is not exhaustive since it would be impossible for the standard to include all sources of danger For example the design of the operated product the way the drive works in the situation it is installed in or even the way the end product is mounted in the end user s place of use cannot be taken into consideration by the drive manufacturer e If any questions or uncertainties regarding the safety instructions contained in the standard arise please contact the manufacturer of the part or end product in question e Only use spare parts tools and additional devices which are authorised by the manufacturer of the drive e Unapproved third party products or modifications to the system and its accessories represent a risk to your safety and the safety of others This means that the use of unapproved third party products or modifications which have not been agreed with or approved by us are prohibited We do not accept liability for damages or injury arising from such actions e Position control devices within sight of the d
16. can be set using the programming unit or the switch on the drive head Connect the wires in the connecting cable of the drive to the wires of the same colour in the programming unit 62 BECKER PR drives Setting the limit positions with switches of type PR 1 Delete both limit positions with the switches Set both switches to O and give a short driving command 2 Setting the lower limit position with the switches QO To lower point Travel the roller shutters to the desired position and switch the corresponding switch from Otol To lower limit Set both switches to I When using anti lifting devices fixed mounting travel the roller shutters downwards until the drive stops automatically 3 Setting the upper limit position with the switches To upper stop Travel the roller shutters towards the upper stop position until the drive stops automatically To upper point Travel the roller shutters to the desired upper position and switch the corresponding switch from O to I in the case of anti lifting de vices this is only possible with a programming unit Programming the limit positions with the programming unit of type PR 1 Setting the lower limit position with the programming unit Connect the wires in the connecting cables of the drive with the wires of the same colour in the Becker programming unit Set both switches to pr
17. d in one of the limit positions only this position will be deleted Setting the intermediate positions for type PROF 4 Programming the intermedia te position ventilation position Travel the drive to the desired intermediate ventilation position and press the STOP and the DOWN button or the STOP and the UP button until the drive clicks once To move to the intermediate ventilation position press the DOWN button or UP button twice in one second double press 5 Deleting the intermediate ventilation position Travel the drive to the position you wish to delete and repeat the programming procedure press the STOP and the DOWN button or the STOP and the UP button until the drive clicks twice Intermediate position Ventilation position 6 Activating the anti freeze protection at the top optional Travel the roller shutter towards the upper limit position Subsequent ly press the programming button until the drive clicks once Then press the programming STOP and UP button simultaneously until the drive clicks three times The same procedure deactivates the anti freeze protection at the top again Note During the installation run first upward and downward travel the drive operates in deadman mode The drive indicates the lack of a limit position by starting up stopping and continuing limit position status indicator Once the limit positions have been detected correctly three times in
18. e control cables safety extra low voltages only use cables with sufficient electrical strength Important safety instructions for handling tubular drives with batteryopera ted or solar power operated control units Keep children away from the control units Device contains small parts that can be swallowed Keep people out of the system s range of movement Only use in dry rooms exceptions SC861 SC561 SC211 SC431 Only use original unmodified Becker parts Observe the country specific regulations Dispose of exhausted batteries properly Only replace batteries with the same type If the system is controlled by one or several transmitters the system s range of travel must always be visible during operation 62 BECKER BECKER Antriebe GmbH Friedrich Ebert Str 2 4 D 35764 Sinn Tel 49 0 27 72 507 0 Fax 49 0 27 72 507 151 info becker antriebe com www becker antriebe com 4995 900 070 1 Stand 10 2010 BECKER Its that easy
19. e stops automatically To retracting limit position point Travel the curtain to the desired retracting position Then press the programming button and the RETRACT button until the drive clicks once 3 Deleting the limit positions via the master transmitter Press the programming button and the STOP button simultaneously until the drive clicks twice after 10 seconds If the curtain is situated between the limit positions both limit positions are deleted in the procedure If the curtain is situated in one of the limit positions only this position will be deleted anes click jl Q A click t is BECKER H X 2x click Setting the intermediate positions for type PSF F 4 Programming intermediate TEER position l gt 5 Travel the curtain to the desired intermediate position and press the STOP and EXTEND buttons until the drive clicks once To travel to intermediate position press the EXTEND button twice J within one second 2 Programming intermediate Dy 1x click position Il a Travel the curtain to the desired intermediate position and press the STOP and RETRACT buttons until the drive clicks once To travel to intermediate position Il press the RETRACT button twice within one second 6 Delete intermediate positi click gt 2x click on I intermediate position Il a Travel the drive to the position you wish to delete and repeat the programming
20. ent in the tube using a screw or a rivet The arrow on the drive head indicates the direction of rotation at The limit position is set via the corresponding adjuster using the flexible tool item no 4933 200 002 0 Turning in the direction increases the range turning in the direction reduces it The barrel may not be turned more than 38 revolutions in one direction gt BECKER M drives Setting the limit positions for M drives 1 Setting the extending limit position After the tube is installed move the drive in the extending direction un til it stops automatically Using the flexible tool turn the corresponding adjuster in the direction clockwi se until the tube is in a suitable po sition for connecting the curtain with the tube Connect the curtain with the tube Retract the curtain until the drive switches off automatically via the limit switch for the retracting limit position Note When delivered from the factory the limit switch range is preset to 2 revolutions in the retracting and extending directions While retracting the drive switches off after 4 5 revolutions Turn the corresponding adjuster in the direction clockwise using the flexible tool until the curtain is in the retracting limit position l D Switch off the retracting mecha nism Using the flexible tool turn the adjuster for the extending limit position 3 10 revolutions in the direc
21. f Serial number e g 10 18 60713 10 year 2010 18 calendar week 60713 consecutive number Connecting PROF drives Drives with electronic limit switching and inte grated radio receiver are connected directly to the power supply The brown wire is connec ted together with the blue wire at the neutral conductor To ensure that the sensible obstacle detection iS active the drive adapter with obstacle de tection must be installed at the drive 64 BECKER CE e 2s GS P44 QB KA Banne Made in Germany N Drive Drive adapter Drive adapter with obstacle detection Information on the PROF drive PROF drives with electronic limit swit ching detect and program the limit positions automatically if stops exist If no stops exist limit switch points are programmed In order for the drive to detect the up per limit position without problems a defined stop must be present angled strip Or mechanical stop Installation with anti lifting devices The anti lifting device must be secure ly engaged and be pressing the roller shutters onto the window sill Programming the master o o A A transmitter Set the drive to programming mode for 3 minutes by switching the power on or by setting the radio switch to the position Subsequently press the pro gramming button at the desired master transmitter until the drive clicks twice 3 sec for initial installation 10 sec to ove
22. he roller shutters are in the upper limit position Pi coR drives Type plate for PicoR drives Type designation e g P 9 16 R P size of drive tube diameter P 35mm 9 16 rated torque output speed R electronic limit switching for roller shutters T suitable for anti lifting device Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 03 28 56789 03 year 2003 28 calendar week 56789 consecutive number Connecting PicoR drives Several drives with electronic limit switching may be connected in parallel to a control sec tion The maximum number of synchronously controlled drives depends on the respective current consumption but must not exceed 5 The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous UP and DOWN commands BECKER KEUR C EA IP44 Made in Germany P9 16R Art Nr 2009 000 001 0 KB 4 mng Ser Nr 032856789 Drive 1 Drive 2 Information on the PicoR drive PicoR drives with electronic limit swit ching detect and program the upper limit position automatically In order for the drive to detect the upper limit position without problems a defi ned stop must be present angled strip or mechanical stop The s
23. imit position automatically if a permanent stop exists If no stop exists a limit switch point is programmed PSF drives PSF drives are used to operate screens awnings and conservatory shading PSF drives PSF drives are used to operate cas sette awnings that require a higher clo sing torque The cassette is then always closed completely Programming the master transmitter Set the drive to programming mode O for 3 minutes by switching the power on or by setting the radio switch to the po sition Then press the programming button on the master transmitter un til the drive clicks twice 3 seconds when installing new drives 10 seconds to overwrite a previously programmed master transmitter Correcting the direction If the drive is moving in the wrong direc tion reverse the directional switch on the drive Attention The direction can only be switched as long as no limit positions have been programmed HNN ATW 2x click 62 BECKER PSF drives Setting the limit positions for type PSF 1 Programming the exten ding limit position via the programming unit Travel the curtain to the extending limit position Then press the pro gramming button and the extending button until the drive clicks once 2 Programming the retrac ting limit position via the master transmitter Q Retracting limit position stop Travel the curtain towards the upper stop until the driv
24. itial installation 10 sec to overwrite a previously programmed master sender Correcting the direction If the drive is moving in the wrong direc tion reverse the directional switch on the drive Attention The direction can only be switched as long as no limit positions have been programmed o gt 2x click 62 BECKER PRF drives Setting the limit positions for type PRF 1 Programming the upper limit position with the master transmitter Q To upper stop Travel the roller shutters towards the upper stop until the drive stops automatically To upper point Travel the roller shutters to the desi red upper position Then press the programming button and the UP button until the drive clicks once S 1x click 23 2 Programming the lower limit position with the master transmitter To lower point Travel the roller shutters to the desired position Then press the programming button and the DOWN button until the drive clicks once To lower stop only with anti lif ting devices Travel the roller shutters down wards until the drive switches off automatically 3 Deleting the limit positions using the master transmitter Press the programming button and the STOP button simultaneously until the drive clicks twice after 10 seconds If the roller shutters are situated bet ween the limit positions both limit posi tions are deleted in the procedure If the rolle
25. ive learns the distance between the limit positions and auto matically concludes the programming phase Using the installation set to delete the final positions Ae click Press the programming button until the drive clicks twice Nonstop 62 BECKER R drives Type plate for R drives Type designation e g R 8 17 R R size of drive tube diameter R 45mm 8 17 rated torque output speed R electronic limit switching for roller shutters T suitable for anti lifting device Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 05 48 50542 05 year 2005 48 calendar week 50542 consecutive number Connecting R drives Several drives with electronic limit switching may be connected in parallel to a control sec tion The maximum number of synchronously controlled drives depends on the respective current consumption but must not exceed 5 The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous UP and DOWN commands Kee CEA py Made in Germany R8 17R Art Nr 2010 020 022 0 RKB 4 mg Ser Nr 054850542 Drive 1 Drive 2 Information on the R drive R drives with electronic limit switching detect and program both limit positions automatically In order for the dri
26. le Design of the individual group and central controls Programming the transmitters Deleting the transmitters Page R 2 Page R 4 PageR 8 Page R 12 Page R 16 Page R 20 Page R 24 Page R 28 Page R 32 Page S 2 Page S 4 Page S 8 Page S 12 Page S 16 Page S 20 Page S 24 Page S 26 Page S 28 Page F 2 Page F 4 Page F 6 Roller Shutter Controls Sun Protection Controls rs Ecer General Which type of roller shutter drive has been installed Possible drive types Type M Drive with mechanical limit switching Type R Drive with electronic limit switching and sensitive obstruction detec tion 1997 2009 Type Pico R Drive with electronic limit switching for the mini tube 1999 2007 Type RF Drives with radio receiver 40 MHz and sensitive obstruction detec tion 2000 2002 Type PRF Drives with radio receiver 868 3 MHz and point to point program ming from 2003 onwards Type PR Drive with electronic limit switching and point to point programming from 2005 onwards Type RP Drive with electronic limit switching point to point programming and sensitive obstruction detection from 2009 onwards means suitable for rigid tube connectors or anti lifting devices How to identify the type of drive Even if the drive is already installed the type can be identified via the programming unit To this end con nect the wires in the connecting cables of the drive to
27. lick o3 ey 3 Setting the sun threshold Remove the labelling space on the rear of the radio controlled handheld trans mitter SWC441 IIl Use the tool provided to turn the sun threshold regulator to the desired setting The sun threshold has 15 possible settings approx 2 klux to 100 klux When slowly turning the regulator the tubular drive clicks to indicate the setting changes 4 Setting the wind threshold Use the tool provided to turn the wind threshold regulator to the desired setting The wind threshold has 11 possible settings approx 2 m s to 22 m s When slowly turning the regulator the tubular drive clicks to indicate the setting changes 5 Checking settings After the threshold values are set the system switches to the TEST mode automatically In the TEST mode the shade function and wind monitoring times are shortened The functions can be controlled in automatic mode End the test mode by using the slide switch on the SWC441 Il to move from automatic mode to manual mode and back to automatic mode If the slide switch is not operated within 15 minutes the test mode is ended automatically C xor C C S Q P Manual mode Automatic mode amp g amp BEC BEC Q 2 BECKER 2 BECKER Q S V 62 BECKER Controls SC211 control Commissioning the motion sensor for awnings SC211 1 Programming the master transmitter Switch off the power supp
28. ller shutters towards the lower limit position until the drive switches off automatically Deleting the limit positions using the programming unit Press the programming button until the drive clicks twice Pa Programming the limit position when installing with anti lifting devices of type R 1 Programming the upper limit position First travel the roller shutters towards the upper limit position until the drive switches off automatically Note When the shutters close for the first time installation run the drive uses less force for safety reasons If the force is configurated close to the limit the drive may stop before re aching the upper limit position After resetting deletion of the limit posi tions the drive is started again until it reaches the upper limit position 2 Programming the lower limit position Then travel the roller shutters towards the lower limit position until the drive switches off automatically Deleting the limit positions using the programming unit N 2x click Press the programming button until the drive clicks twice 62 BECKER RP drives Type plate for RP drives Type designation e g R 8 17RP R size of drive tube diameter R 45mm 8 17 rated torque output speed P point to point programming possible R electronic limit switching for roller shutters F suitable for anti lifting device Operating mode sho
29. ly on the ra dio receiver drive type PSF and then switch it back on Press the programming button on the master transmitter SWC241 II until the drive clicks twice Note Follow the instructions on pa ges S 22 and S 23 to set the limit po sitions for the PSF drive 2 Programming the SC211 a Remove the labelling space on the rear of the radio controlled hand held transmitter SWC24 II Use the tool provided to turn the wind threshold regulator clockwise to the maximum setting Then press the programming button until the drive clicks once b Press the red programming button of the SC211 O until the tubular drive clicks once c Press the red programming button again until the tubular drive clicks twice 1x click G o Ga c i c 1 oF c E wl 1x click a i 2x click a 3 Setting the wind threshold Use the tool provided to turn the wind threshold regulator at the SWC241 II to C the desired setting The wind threshold has 11 possible settings approx 2 m s to 22 m s C When slowly turning the regulator the emm tubular drive clicks to indicate the setting F changes C 4 Setting the release angle Use the tool provided to set the release angle on the rotary switch of the PCB 0 0ff 1 Sensitive 9 Insensitive 2 5 Programming the release Q angle Move the awning to the extending limit al position After
30. mming button and keep it pressed Press the button and keep it pressed Release the programming button Press the programming button again until the drive clicks twice If the drive is situated between the limit positions both limit positions are deleted If the drive is situated in one of the limit positions only this position will be deleted 62 BECKER PSF drives Type plate for PSF drives Type designation e g R30 17C PSF R size of drive tube diameter G BECKER P 35mm CE 2 R 45mm 2S GS P44 KE To Rn 6 PSF O 30 17 rated torque output speed Art Nr 2030 130 135 0 C pluggable connecting cable P point to point programming U 230 V f o i possible a er S electronic limit switching for sun protection Made in Germany F radio receiver T higher closing torque for cassette awnings Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 08 49 20095 08 year 2008 49 calendar week 20095 consecutive number Connecting PSF drives Drives with electronic limit switching and inte grated radio receiver are connected directly Drive to the power supply The brown wire and the black wire are clasped together on the outer conductor L1 Information on the PSF drive PSF drives with electronic limit switching detect and program the retracting l
31. n and keep it pressed Press the button and keep it pressed Release the programming button Press the programming button again until the drive clicks twice Note When the shutters close for the first time installation run the drive uses less force for safety reasons If the force is configurated close to the limit the drive may stop before reaching the upper limit position Af ter reversing a short way the drive is started again until it reaches the up per limit position The drive indicates the lack of a limit position by driving forward stopping and then continuing limit position status indicator Once the limit positions have been detected 3 times consecutively without problems 3 opening and closing movements the drive saves the limit positions 4 Activating the cyclic curtain length adjustment optional By pressing the programming button on the programming unit for 10 seconds you activate the cyclical curtain length adjustment The drive confirms the action by clicking three times After the programming is completed 3 complete opening and closing movements the roller shutters stop shortly before reaching the upper limit position and will only reach the stop every 32nd time correction run 62 BECKER PR drives Type plate for PR drives Type designation e g R 8 17 C PR R size of drive tube diameter P 35mm R 45mm 12 17 rated torque output speed C
32. ogramming setting D Q To lower point Travel the roller shutters to the desired position and press the pro gramming button on the program ming unit until the drive clicks once To lower stop When using anti lifting devices fixed mounting travel the roller shut ters downwards until the drive stops automatically 2 Setting the upper limit positi on with the programming unit To upper stop Travel the roller shutters towards the upper stop until the stops automati Cally To upper point Travel the roller shutters to the desi red upper position and press the pro gramming button on the program ming unit until the drive clicks once 1x click 3 Deleting the limit positions using the programming unit Press the programming button and keep it pressed Press the button and keep it pressed Release the programming button Press the programming button again until the drive clicks twice If the drive is situated between the limit positions both limit positions are dele ted If the drive is situated in one of the limit positions only this position will be deleted BECKER PRF drives Type plate for PRF drives Type designation e g R8 17 C PRF R size of drive tube diameter P 35mm R 45mm 8 17 rated torque output speed C pluggable connecting cable P point to point programming possible R electronic limit switches for roller shutter
33. pluggable connecting cable P point to point programming possible R electronic limit switching for roller shutters i suitable for anti lifting device Operating mode short time operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 08 40 961630 08 year 2008 40 calendar week 961630 consecutive number Connecting PR drives Several drives with electronic limit switching can be connected in parallel to a control section The maximum number of synchro nously controlled drives depends on the respective current consumption but must not exceed 5 The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous UP and DOWN commands Drive 1 Sa Ser Nr 0840961630 Made in Germany Drive 2 BECKER CE eq AGS P44 GD KB 4 min Information on the PR drive PR drives with electronic limit swit ching detect and program the limit po sitions automatically if stops exist If no stops exist limit switch points are programmed In order for the drive to detect the up per limit position without problems a defined stop must be present angled strip Or mechanical stop Installation with anti lifting devices The anti lifting devices must be secu rely engaged and be pressing the roller shutters onto the window sill The limit positions
34. prings are attached to the mini tube using tube clamps This stops the springs from dragging against the drive The limit positions can be set using any operator control Limit positions are deleted using the pro gramming unit Connect the wires of the connecting cable of the drive to the wires of the same color in the programming unit rs Ecer Pi coR drives Programming the end positions for type PicoR 1 Programming the upper limit position First travel the roller shutters towards the upper limit position until the drive switches off automatically Note When the shutters move up wards for the first time installation run the drive uses less force for sa fety reasons If the force is configu rated close to the limit the drive may stop before reaching the upper limit position After resetting deletion of the limit positions the drive is star ted again until it reaches the upper limit position 2 Programming the lower limit position Now travel the roller shutters to thedesi red lower limit position If anti lifting devices or rigid safety springs are installed travel the roller shutters downwards until the drive stops automatically 3 Programming the travelling distance Travel the roller shutters towards the upper limit position again without in terruption until the drive switches off automatically This time the dr
35. procedure press the STOP and EXTEND buttons or STOP and RETRACT buttons until the drive clicks twice 2 2 SWS241 control set Commissioning the radio controlled Sun Wind Set with handheld transmitter and SWS241 sensor 1 Programming the master transmitter a Travel the curtain to a centre positi on using the UP STOP DOWN toggle switch b Press the programming button on the SWC510 The SWC510 is now in programming mode for 3 minutes c When in the programming mode press the programming button on the radio controlled handheld trans mitter SWC441 II until a confirmation the curtain shifts is received Note In order to recognise the shift clearly the curtain should be situated between the limit positions I 2 Setting the sun threshold Remove the labelling space on the rear of the radio controlled handheld trans mitter SWC441 IIl Use the tool provided to turn the sun threshold regulator to the desired setting The sun threshold has 15 possible settings approx 2 klux to 100 klux When slowly turning the regulator the curtain shifts to indicate the setting changes 3 Setting the wind threshold Use the tool provided to turn the wind threshold regulator to the desired setting The wind threshold has 11 possible settings approx 2 m s to 22 m s When slowly turning the regulator the curtain shifts to indicate the setting changes 4 Checking settings Afte
36. pter against axial displacement in the tube using a screw or a rivet The arrow on the drive head indicates the direction of rotation at The limit position is set using the corresponding adjuster for example the flexible tool item no 4933 200 002 0 Turning in the direction increases the range turning in the direction reduces it The barrel may not be turned more than 38 revolutions in one direction gt BECKER M drives Setting the limit positions for M drives 1 Setting the lower limit position After the tube is installed move the drive downwards until it switches off auto matically Using the flexi ble tool turn the corres ponding adjuster in the direction clockwise until the tube is in a suitable po sition for connecting the roller shutter to the tube Switch off the down di rection and connect the roller shutters to the tube mount the springs gt A LT 2 Setting the upper limit position Travel the roller shutters upwards until the drive switches off automatically via the limit switch for the upper limit position Note When delivered from the factory the limit switch range is preset to 2 revolutions in the up and down di rections While moving up the drive switches off after 4 5 revolutions Turn the corresponding adjuster in the direction clockwise until t
37. r shutters are situated in one of the limit positions only this position will be deleted Setting the intermediate positions for type PRF 4 Programming the intermedia te position Move the drive to the required inter mediate position and press the STOP and DOWN buttons until the drive clicks once To drive up to the intermediate positi on press the DOWN button twice in one second Double press 5 Programming the ventilation position Move the drive to the required ventilation position and press the STOP and UP but tons until the drive clicks once To drive up to the ventilation position press the UP button twice in one second Double press 6 Deleting the intermediate position ventilation position Travel the drive to the position you wish to delete and repeat the programming procedure press the STOP and DOWN buttons or STOP and UP buttons until the drive clicks twice vA gy 62 BECKER PROF drives Type plate for PROF drives Type designation e g R8 17 C PROF R size of drive tube diameter P 35mm R 45mm 8 17 rated torque output speed C pluggable connecting cable P point to point programming possible R electronic limit switches for roller shutters O sensitive obstacle detection F radio receiver T suitable for anti lifting device Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool of
38. r the thresholds are set the system switches to the TEST mode automatically Inthe TEST mode theshade function and wind monitoring times are shortened The functions can be controlled in automatic mode End the test mode by using the slide switch to move from automatic mode to manual mode and back to automatic mode If the slide switch is not opera ted within 15 minutes the test mode is ended automatically C xor C C S Q P Manual mode Automatic mode amp g amp BEC Q 2 BECKER 2 BECKER Q S V 62 BECKER Controls SWS441 SWS641 control set Commissioning the radio controlled Sun Wind Set with handheld transmitter and SWS441 SWS641 sensor 1 Programming the master transmitter Switch off the power supply on the radio receiver drive type PSF and then switch it back on Press the program ming button on the master transmitter until the drive clicks twice Note Follow the instructions on pages S 22 and S 23 to set the limit positions for the PSF drive 2 Programming the SC811 SC861 a Press the programming button of the master transmitter O until the tubular drive clicks once b Press the programming button of the SC811 SC861 until the tubular drive clicks once c Press the programming button of the SC811 SC861 again until the tubular drive clicks twice i ry 2x click og a 1x click o4 2x c
39. riven product at a height of over 1 5 m e Rated torque and duty cycle must be suitable for the requirements of the driven product e Technical data rated torque and service life can be found on the type plate of the tubular drive e Moving parts of the drive must be installed at a height of more than 2 5 m above floor level or other flat surface which allows access to the drive e To connect the drive to the driven part solely components from the current Becker mechanical accessory catalogue may be used Important safety instructions for handling tubular drives with mains operated control units Keep children away from the control units Device contains small parts that can be swallowed Risk of injury due to electric shock Connections to the 230 V mains must always be performed by a specialist Disconnect the connecting cable from the power prior to installation Always comply with regulations of local energy supply companies and VDE 100 provisions for wet and damp rooms during installation Keep people out of the system s range of movement Only use in dry rooms exceptions VCJ470 VC410 VC510 SWC510 Only use original unmodified Becker parts Observe the country specific regulations Dispose of exhausted batteries properly Only replace batteries with the same type If the system is controlled by one or several appliances the system s range of travel must always be visible during operation When connecting th
40. rt period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 09 01 102030 09 year 2009 01 calendar week 102030 consecutive number Connecting RP drives Several drives with electronic limit switching can be connected in parallel to a control sec tion The maximum number of synchronously controlled drives depends on the respective current consumption but must not exceed 5 The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous UP and DOWN commands BECKER KEUR CEA P4 GD Made in Germany R8 17RP Art Nr 2010 120 022 O emg Ser Nr 0901102030 Drive 1 Drive 2 Information on the RP drive RP drives with electronic limit swit ching detect and program both limit po sitions automatically If no stops exist limit switch points are programmed In order for the drive to detect the upper limit position automatically a defined stop must be present angled strip or mechanical stop Installation with springs of type RP No more than one roller shutter bar should jut out over the intake guide In the lower limit position the springs must counteract the tube s rotary motion The springs should be mounted 30 cm apart from one another Installation with anti lifting devices of type RP The anti lifting devices must be securel
41. rwrite a previously programmed master sender Correcting the direction If the drive is moving in the wrong direc tion reverse the directional switch on the drive Attention The direction can only be switched as long as no limit positions have been programmed 62 BECKER PROF drives Setting the limit positions for type PROF 1 Programming the upper limit position with the master transmitter QO To upper stop Travel the roller shutters towards the upper stop until the drive stops automatically To upper point Travel the roller shutters to the desi red upper position Then press the programming button and the UP button until the drive clicks once S 1x click 23 2 Programming the lower limit position with the master transmitter To lower point Travel the roller shutter downwards until the drive switches off automatically the drive adapter with obstacle detection must be used for installation with springs To lower point Travel the roller shutter to the desired position Subsequently press the programming and the DOWN button until the drive clicks once 3 Deleting the limit positions using the master transmitter Press the programming button and the STOP button simultaneously until the drive clicks twice after 10 seconds If the roller shutters are situated between the limit positions both limit positions are deleted in the procedure If the roller shutters are situate
42. s F radio receiver J suitable for anti lifting device Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 08 49 20071 08 year 2008 49 calendar week 20071 consecutive number Connecting PRF drives Drives with electronic limit switching and inte grated radio receiver are connected directly to the power supply The brown wire and the black wire are clasped together on the outer conductor L1 64 BECKER CE G ANGS IP44 R 8 17 C PRF Art Nr 2010 120 124 0 KB 4 min Ser Nr 084920071 Made in Germany Drive Information on the PRF drive PRF drives with electronic limit switching detect and program the limit positions automatically if stops exist If no stops exist limit switch points are programmed In order for the drive to detect the upper limit position without problems a defi ned stop must be present angled strip or mechanical stop Installation with anti lifting devices The anti lifting device must be secure ly engaged and be pressing the roller shutters onto the window sill Programming the master transmitter Set the drive to programming mode for 3 minutes by switching the power on or by setting the radio switch to the position Subsequently press the pro gramming button at the desired master transmitter until the drive clicks twice 3 sec for in
43. t position If the drive runs without interruption it is a PR drive from 2003 onwards If the drive interrupts after one turn and then continu es itis a RP drive from 2009 onwards gt BECKER M drives Type plate for the M drive Type designation e g R 8 17 C M R size of drive tube diameter P 35mm R 45mm L 58mm 8 17 rated torque output speed C pluggable connecting cable M mechanical limit switch Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 08 40 961630 08 year 2008 40 calendar week 961630 consecutive number Connecting M drives Drives with mechanical limit switching must not be connected in parallel to a control sec tion A discharge of the capacitor could dama ge the limit switch This would cause the limit positions to be overrun The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous UP and DOWN commands Sa Ser Nr 0840961630 Made in Germany Drive 2 BECKER CE eq AGS P44 GD KB 4 min Information on drive type M Before installation make sure that the drive adapter safety catch has engaged is screwed on tightly Mark the position of the drive adapter on the tube and drill a 4 mm hole at this point Secure the drive ada
44. ted Sun protection function swit ched off MA eS CG x 1 x y0 xM ne ca lt q o LED red LED green LED flashes Twilight func Twilight func yellow tion not being tion being exe Rotary switch executed cuted setto 0 Twilight func tion switched off as y 0 2 BECKER BECKER Automatic on N at Automatic off Roller Shutter Controls 62 BECKER General Which type of sun protection drive has been installed Possible drive types Type M Drive with mechanical limit switching Type S Drive with electronic limit switching 1997 2003 Type SF Drives with electronic obstruction detection and radio receiver 2000 2003 Type PS Drives with electronic limit switching and point to point programming from 2003 onwards Type SEB Drives with electronic limit switching and automatic reversal fabric stretching in the extending limit position from 2003 onwards Type PSF Drives with radio receiver and point to point programming from 2003 onwards means higher closing force for cassette awnings How to identify the type of drive The drives can be identified using the programming amp BECKER unit even when they are installed Connect the wires in the connecting cables of the drive to the wires of the En B same colour in the Becker programming unit Perform the following steps one after the other Press the programming button for 2 seconds
45. ter transmitter for three seconds until the radio controlled drive clicks once or the external radio controlled receiver moves slightly Subsequently press the program ming button at the transmitter to be deleted for three seconds until the radio controlled drive clicks once or the external radio controlled receiver moves slightly Subsequently press the pro gramming button again at the transmitter to be dele ted for ten seconds until the radio controlled drive clicks twice or the external radio controlled receiver confirms deleting slight movement twice Deleting all the transmitters except the master transmitter Press the programming button at the master transmitter for three seconds until the radio controlled drive clicks once or the external radio controlled receiver moves slightly Press the programming button again at the master transmitter for three seconds until the radio controlled drive clicks once or the external radio controlled receiver moves slightly Subsequently press the program ming button again at the transmitter or ten seconds until the radio controlled drive clicks twice or the external radio controlled receiver confirms deleting slight movement twice a 1x click 1x clic 5 2x click BECKER Important safety instructions Caution Failure to observe these instructions can lead to serious injuries
46. those of the same colour in the Becker programming unit Perform the following steps one after the other Press the programming button for 2 seconds If the drive produces a loud noise and the tube does not turn the drive is a type M Replace the program ming unit immediately with one that is suitable for an M drive If the drive clicks twice a type R has been installed If the drive clicks once or does not react itis a PicoR PP PR RF or PRF drive Let the drive turn twice and then press the program ming button again for 2 seconds another click indica tes that a second limit position has been set Let the drive turn once in the opposite direction and carry out the following procedure for deleting Press the programming button and keep it pressed Press the button and keep it pressed Release the programming button Press the programming button again until the drive clicks twice If the drive does not react drives with integrated radio controlled receiver type RF up to 2002 tyoe PRF from 2003 onwards or type PROF from 2011 on wards have been installed If the drive clicks twice PicoR RP or PR drives were installed Press the programming button again If the drive does not react a PicoR drive up to 2007 has been installed If the drive clicks once it is a RP or PR drive You have now programmed a limit position Let the drive turn twice from the limi
47. tion depending on how many times the fabric is wrapped around the tube when the curtain is extended 2 Setting the retracting limit position Travel the curtain in the extending direction until the drive switches off automatically via the limit switch for the extending limit position Using the flexible tool turn the adjuster for the extending limit position in the direction clock wise until the desired extending position is reached gt BECKER S drives Type plate for S drives Type designation e g R 20 17 S R size of drive tube diameter R 45mm L 58mm 20 17 rated torque output speed S electronic limit switches for sun protection higher closing force for cassette awnings Operating mode short period operation S2 After 4 minutes of continuous operation the drive must be allowed to cool off Serial number e g 05 48 50572 05 year 2005 48 calendar week 50572 consecutive number Connecting S drives Several drives with electronic limit switching can be connected in parallel to a control section The maximum number of synchro nously controlled drives depends on the load capacity of the operator control The changeover time for switching the running direction must be at least 0 5 seconds The switch and controls must not execute simulta neous RETRACT and EXTEND commands The following applies to operator controls with a 5A contact load rating R8 17 S R1
48. ve to detect the upper limit position without problems a defi ned stop must be present angled strip or mechanical stop Installation with springs of type R No more than one roller shutter bar should jut out over the intake guide In the lower limit position the springs must counteract the tube s rotary motion The springs should be mounted 30 cm apart from one another Installation with anti lifting devices of type R The anti lifting device must be securely engaged and be pressing the roller shut ters onto the window sill The limit positions can be set using any operator control Limit positions are deleted using the pro gramming unit Connect the wires in the connecting cable of the drive to the wires of the same colour in the programming unit Ee 62 BECKER R drives Programming the limit position when installing with springs of type R 1 Programming the upper limit position First travel the roller shutters towards the upper limit position until the drive switches off automatically Note When the shutters close for the first time installation run the drive uses less force for safety reasons If the force is configurated close to the limit the drive may stop before re aching the upper limit position After esetting deletion of the limit posi tions the drive is started again until it reaches the upper limit position 2 Programming the lower limit position Then travel the ro
49. y engaged and be pressing the roller shut ters onto the window sill The limit positions can be set using any operator control Limit positions are deleted using the programming unit Connect the wires in the connecting cable of the drive to the wires of the same colour in the programming unit 62 BECKER RP drives Programming the limit positions with the programming unit of type RP 1 Programming the upper limit position Connect the wires in the connecting cables of the drive to the wires of the same colour in the Becker programming unit To upper stop Travel the roller shutters towards the upper limit position until the drive automatically stops To upper point Move the roller shutters to the desi red upper position and press thepro gramming button on the program Typ RP Typ RP ming unit until the drive clicks once txclick N 4 amp BECKER 2 Programming the lower limit position To lower stop Travel the roller shutters downwards until the drive switches off automati cally due to the effect of the springs tyoe PR or being blocked by the anti lifting devices type RP To lower point Travel the roller shutters to the desi red position and press the program ming button on the programming unit until the drive clicks once l amp BECKER 3 Deleting the limit positions via the programming unit Press the programming butto
Download Pdf Manuals
Related Search