ASA Industrial Electric Screwdriver User's Manual
Contents
1. After use Storage and maintenance when the unit is to be stored for a long period remove the power supply and bit open the carbon brush cover and blow out any accumulated carbon brush dust with compressed air and wipe the exterior clean Then store the screwdriver carefully in a dry dust free place away from direct sunlight Store the bit in grease To ensure continued serviceability periodically check and maintain the screwdriver Troubleshooting If the screwdriver does not work properly check the list below If you cannot solve the problem do not open the unit Contact one of our authorized agents as soon as possible If the screwdriver does not run e Check that the power supply is outputting power Check that the power supply plug is inserted properly and that output plug terminals No 1 and NO 3 show 30VDC approximate between them If no output is shown change the power supply Check for a open or short circuit in the 3p 3p cord connecting the screwdriver to the power supply If an open or short circuit is found change the cord or plug use plug type 2G2016 3P or purchase equivalent type e Check that the rotation direction switch are working properly If no click is heard when a trigger is depressed it is not working and must be replaced make sure to perform this check in a quiet place If the screwdriver is not rotating normally e There is a protective circuit within the power supply Powe2. in order to prevent it from being knocked down and suffering external cracking internal damage or a snapped power cord When the selected torque is reached This product features an internal clutch assembly When a screw is driven and the selected torque is reached the clutch assembly will automatically disengage and a click will be heard At this point even if the forward trigger is not released the power to the motor will be automatically cut off Note When driving screw grasp the screwdriver firmly in order to prevent upwards recoil generated by the clutch release from forcing the screwdriver bit edge form the screw slot and damaging slot When removing screws when a previously driven screw cannot be removed using the same torque that it was driven with raise the torque setting After the screw is removed return the regulating handle to its original setting To simplify this operation note the number click sounds generated as the regulating handle is turned Operational frequency suggest the operational frequency 1 4 ON OFF second the total screws 7000pcs 8hours don t over our operational frequency suggest and avoid the inside part of screwdriver serious damage If everyday work 8hours upward please use two screwdriver by turns protect the life of screwdrivers Guide for 3P plug in MAN guide notch 4 receptacle screwdriver side
3. 000F 1 3 0 7W 3644 1 3 0 7 W6644 BS 6000 2 5 0 7W3864 2 6 0 7 W6964 1 3 0 7W 3644 1 3 0 7 W 6644 BS 6500 2 5 0 7W3864 2 6 0 7 W6964 Power supply optional Dimension mm Operation volt Output volt weight Model L W H AC DC g 1b Approval APS 301A 150 65 40 100 240 20 35 350 0 77 UL CE 3C Before use read the following Use the correct voltage Carefully check the voltage shown on the power supply and this manual and determine the correct voltage Only plug the unit into a power source of the correct voltage Determine the appropriate torque range choose the correct screwdriver for the torque you will require To lengthen product life avoid long term high torque use Make sure the screwdriver is undamaged If the power code is scraped or damaged it should be immediately unplugged and replaced to avoid electric shocks or a short circuit that could result in fire Use in an appropriate work environment To ensure safety do not use in high temperature high humidity environments or near flammable materials Keep the power cord away from tools or equipment that might scrape or melt it When plugging in or unplugging the power cord hold the plug firmly Never pull on the cord Method of operation and important points Drivin
4. 700 1000 700 1000 Torque setting Stepless oz Machine Screw 1 9 5 970 04 0 09 1 0 2 6 0 04 0 1 1 4 3 0 0 06 0 12 2 2 4 2 0 08 0 14 2 6 4 0 0 1 0 16 3 5 mm in Ola ae ga EE N 1 0 2 0 0 04 0 08 1 0 2 3 0 04 0 09 1 4 2 6 0 06 0 10 2 0 3 2 0 08 0 12 2 3 3 5 0 09 0 14 Weight g 1b 4129 0 91b Length mm in 227mm 8 9in Available bit shank 5 or 1 4 6 35 Hex shank Power consumption W 60 Available power supply APS 301A Clutch impact Just one time when torque up BIT SLIDE SLEEVE TORQUE COVER Outline This drawing applies only to 1 4 bit shank screwdrivers 227mm 8 9 in RING 50mm 1 96in 033mm FORWARD TRIGGER ENGRAVING FWD OFF REV SW REVERSE TRIGGER HANGER RING Accessories This product comes supplied with a power code and two bits Bits one set per screwdriver t t oe gU e tee j a 50 i 50 ee hex shank Bit specificatio 50 cee T Available Ti Ti Screwdriver i 1p i 1P Model Tip No diameter D S Hp No diameter D ie 00 91 7 7W3204 00 1 7 7W6204 BS 2000 00 2 0 7W 3404 00 2 0 7 W6404 1 3 0 7W 3644 1 p45 7 W6744 BS 3000 0 2 5 7W3524 0 2 5 7W6524 1 3 0 7W 3644 1 3 0 7W6644 BS 4000 2 65 0 7W3864 2 4 5 7W6764 BS 4
5. g and removing screw insert the tip of the screwdriver bit accurately into the screw slot and press down lightly To drive a screw depress the Forward trigger To remove a screw depress the Reverse lever Either of these actions will automatically engage the motor If both the Forward and Reverse levers are depressed at the same time the screwdriver will not rotate Note During operation do not switch quickly between rotation directions Release one lever and wait for the motor to stop fully before depressing the other lever Torque settings Use the regulating handle to set the torque Turning it in a clockwise direction into the screwdriver will increase the torque Turning it counterclockwise out of the screwdriver will decrease the torque Note The engraved markings on the engraving ring are for reference only and do not indicate torque output Torque output can only be determined by repeated testing with a torque meter or hand held spanner torque meter To prevent your torque setting from being changed we can provide a torque cover which covers and secures the regulating handle Bit insertion Use your finger to depress the slide sleeve into the screwdriver and insert an appropriate bit When the slide sleeve is released the bit will be automatically engaged Note Do not hammer the bit in or pull it out forcibly Secure screwdriver during operation During operation hang the screwdriver up securely as from balancer
6. he date of purchase entered on the Product Information Form The retailer s stamp must appear on the form to confirm the date However the following circumstances we will charge the user for any parts and labor cost associated with repairs For repairs involving normal wear to parts including carbon brushes bits and power cord and also to the exterior surface If the screwdriver was connected to a power source of the incorrect voltage If there was inappropriate use or an attempt to repair the unit by the user After the period of the guarantee or if the user cannot present the manual with stamped Product Information Form Retailer s Stamp Specifications and design may be changed without notice for improvement A 0 Serial No ASA Industrial Electric Screwdriver User s Manual for full automatic models brushless motor with controller A Word of Thanks to Our Customers Thank you for choosing lightweight and powerful electric screwdrivers In order to insure maximum performance and product life please read through this manual before using your screwdriver Feature Adopted the high precision low inertia and low impact driving brushless motor long lift high quality Our screwdrivers are designed for use with precision torque locking screws It can be used for assembly of small items such as mobile phone cameras and eyeglasses and large items such as
7. home appliances computers and furniture Unneeded carbon brush replace effective reduce the expense for business Low vibration low noise meets environmental protection demands It s motor does not generate any carbon particle over flow to reduce air pollution and protect our environment Connecting with soft start and speed adjustable function power supply not only match to differ fastening condition but also keep the best fastening quality With the most prominent gold plated micro switch The service life of the contact point withstands 10 million on and off contacts to more reduce the costs of maintenance Design features separation of screwdriver and control for low repair costs and higher serviceability rate Switching power supply plugs directly into screwdriver and supplies stabile voltage provides more accurate torque and longer motor life Right angel 90 head adapter attaches easily to screwdriver for use in small spaces gt 60mm operates smoothly Optional Ergonomically designed exterior reduces work fatigue and increases productivity Specifications O SS Model Power source Torque range kgf cm 1bf in BS 2000 0 3 2 0 0 26 1 7 BS 3000 0 5 5 0 0 43 4 3 BS 4000 4000F 30VDC 1 0 12 0 87 10 4 BS 6000 2 0 16 0 1 7 13 9 BS 6500 4 0 20 0 3 5 17 4 No load speed rpm 700 1000 700 1000 700 1000 1400 2000
8. r is only supplied normally from 3 to 5 seconds after current flow begins e If the motor only runs intermittently during Forward operation try Reverse operation or rotate the anvil 90 degrees until a click is heard then re attempt Forward operation e Long term use causes the motor s commutator to wear down In this case it must be replaced this repair must be performed by one of our authorized agents If the bit falls out easily or wobbles e check that the bit matches our specifications If not change the bit to one that does e Check that the bit is inserted tightly into two guide channels within the anvil If not remove the bit and re insert it tightly e If the bit tends to wobble remove the bit rotate it 60 or 180 degrees and re insert it If the screwdriver does not stop when the selected torque is reached e An excessive torque setting can cause the screw to strip the threads with the result that the clutch does not activate Lower the torque to a level that does not cause stripping e Differences in size between the bit tip and screw slot lengths can cause slopping Change to a suitable bit tip e The brake circuit may be damaged or the sensor switch may have shifted this repair must be performed by one of our authorized agents Warranty We provide a one year free repair service warranty with this product The warranty is good for one year from t
Download Pdf Manuals
Related Search