Picotrack Endurance User Manual Version 2.6
Contents
1. P67 grade housing IP67 connector is used for configuration and charging USB power supply No effort to replace batteries Figure 2 Picotrack Endurance Rechargeable Telic Telematics amp Telemetry Delivery content The standard delivery includes the Endurance device plus 16 screws The delivery could include furthermore some of the following accessories depending on the details of your purchase order Accessory Name Order Code Functionality USB Charging 17013 cable for Picotrack Endurance Rechargeable USB Cable for 16211 Use this cable to charge the Config Tool Endurance Rechargeable and Picotrack to configure the device via Endurance Config Tool Rechargeable USB Cable for 16210 This cable allows to configure Config Tool the Endurance Primary via Picotrack Config Tool Endurance Primary Table 1 Accessories List Telic Telematics amp Telemetry 2 1 Technical Data The following table lists key technical parameters for the products Picotrack Endurance Picotrack Endurance Primary Rechargeable 230 x 130 x 41 mm 230 x 130 x 41 mm IP67 charging cable IP Protection Class IP69k IP67 3 indicators for the states Status LEDs GSM GPS battery charging full rechargeable only DOTA On Off button Quadband GSM Module GSM GPRS module 850 MHz 900 MHz 1800 MHz 1900 MHz GPS Sensitivity Tracking 165 dBm GPS Acquisition Time Cold 34sec Warm 33 sec Hot lt 1 sec GPS C2. Telic Telematics amp Telemetry 25 26 27 Telic Telematics amp Telemetry Table Overview Tahle LS Accessories SE s sacs cect di apie Kadakad sz kud E EET EATE TEE 7 Table 2 Technical parameters for the product unese zzskdoauij ea ooo kibucech zd 8 Tahle 3 Stat s inditat r zu 4 ia rad oak o hm o oko dra ad a rd 13 Table 4 Troubleshooting Device doesn t show any sign Of life e 420eee 20000eeee00eeeeeeeee nen 16 Table 5 Troubleshooting Device doesn t log into the GSM network lt lt lt lt lt lt lt lt lt lt oz ees 16 Table 6 Troubleshooting Device doesn t log into the GPRS network lt lt lt lt lt lt lt lt lt lt ees eee 17 Table 7 Troubleshooting Device doesn t send MESSABES ccssscccecssssececseseeeececssaeeeeseeeeeeseeeeeeeeeseaeeeenees 17 Table 8 Troubleshooting Device doesn t receive GPS data lt 4444 44 lt s40404esee0000eeeeeeereee 17 Tahle 9 Content GSC TPO dar pst eneeseuitslaneaiit dete sisteaa SAK aro soda ao E dod vaze TEETE E 19 Table 10 Documentation change LOG zs zdnse banda aokukzboot a a a E a E a 27 Figure 1 Picotrack Endurance Primary siclaivasccagederecsadidsentttedasulcalaehiaedealersiuedanaddaddan nd iasdaedeescaate saunas ecesaladders 5 Figure 2 Picotrack Endurance Rechargeable sci csccisicedccsnsiecsetadvatoasesienns sednediassbaciestaueetincavicendandeccduesyaudensevvdent 6 Figure 3
3. Geofencing Roaming alternative configuration The device is able to detect a GSM roaming status and swap automatically to an alternative setup for roaming this alternative setup has to be previously configured This allows optimizing the data traffic and reducing the communication costs Device Watchdogs The Picotrack has different integrated watchdogs They automatically check the functions of the device and generate resets as soon as they recognize any malfunction Malfunction could occur due to internal problems of the device problems related to the GSM connection problems with the GPS reception and many more This watchdog concept ensures that the Picotrack can automatically return to stable operation if necessary Control of the watchdogs by the user is not necessary If the watchdog has to restart the device it may happen that some of the position messages and respectively events are not logged and as a result they are not transmitted to the tracking server Device based wireless positioning GSM Tracking The device can be configured in order to get a localization obtained by the GSM module in case that the GPS has some difficulties on providing a valid fix Of course this position will be less accurate and take a bit longer than the standard way by GPS module therefore this functionality has to be considered as emergency backup for the GPS 20 Telic Telematics amp Telemetry Note that this feature is only availab
4. e g by putting the SIM card into your cell phone and checking whether your cell phone is able to log into a GSM network Please check whether the SIM card is locked This can be done e g by putting the SIM card into your cell phone and checking whether your cell phone is able to log into a GSM network If this not the case then please try to make a phone call If you are successful the SIM card is definitely not locked Please recharge the SIM card in the Picotrack device If they aren t recharged on a regular basis often after 12 or 24 months In this case usually you have to buy a new SIM card Please remove the SIM card from the device and check the PIN code The Pin code has to be deactivated or set to 0000 After a triple wrong entry of the PIN unblocking the SIM card requires the PUK Please check the correct position of the SIM card in the card holder Table 5 Troubleshooting Device doesn t log into the GSM network 16 5 3 5 4 5 5 Telic Telematics amp Telemetry The device doesn t log into the GPRS network Possible issue source Trouble shooting The GPRS service is not yet Please ask your provider whether the GPRS function is already activated activated for the SIM card in use Table 6 Troubleshooting Device doesn t log into the GPRS network The device doesn t send messages Possible issue source Trouble shooting Battery of the device was Please recharge the devi
5. motion it is necessary to open the cover and press the white button like in the Primary cell device version In order to preserve the IP67 enclosure rating do not forget to plug the small black lid after using the serial interface before deploying the device in the field 15 Telic Telematics amp Telemetry Troubleshooting Hints The device doesn t show any sign of life Possible issue source Trouble shooting The device is not connected correctly Please connect the device following instructions in the user manual Table 4 Troubleshooting Device doesn t show any sign of life 5 2 The device doesn t log into the GSM network Possible issue source Trouble shooting The device isn t in a GMS covered area The position of the Picotrack device is not favourable The SIM card in the Asset Tracking device is new and has not yet been activated The SIM card has been locked by the provider The prepaid bonus is exhausted The prepaid SIM card is no longer valid The PIN code of the card has not been deactivated or is not set to 0000 The SIM card hasn t been inserted into the SIM card holder in the correct way Please check whether there is GSM reception in this area e g using a cell phone and move eventually to another area Choose another place in the vehicle which might be less shielded Please check whether the SIM card is already activated This can be done
6. the middle LED is off this does NOT mean that the Telic Picotrack tracking and tracing module is switched off In fact it only indicates that the device is not connected to external power supply The red LED indicates the following This one and the red right indicator are permanently on during the 12 Telic Telematics amp Telemetry Picotrack Endurance Primary Rechargeable whole DOTA Software Update Over The Air procedure During download of data when the DOTA is running the green LED on the left indicator is also on It is blinking red when the battery is Low indicating that the battery needs to get recharged soon otherwise the Picotrack will switch off automatically In case of an internal device reset this LED will be on for about 5 seconds and then return to its initial status At the same time the red LED of the right indicator will be also switched on Also whenever the internal button is pushed the middle LED will illuminate red in order to indicate the button is being pushed Left indicator The left indicator consists of both a green LED and a red LED The green LED reflects the GSM status and also whether the device is switched on When the LED is off the device is switched off Permanently on means GSM is switched on but no GSM network is available Blinking once means the device is logged into the GSM network Blinking twice indicates an established TCP IP connection to the server Slow doubl
7. 0270 0865 5168 14 26 Telic Telematics amp Telemetry 12 Documentation change LOG mm P m 21 01 14 First release on new layout 14 04 2014 Add the CE Declaration of Conformity 22 05 14 Update Installation on board Section 7 Rev 2 3 23 05 2014 Update Figure description Figure 4 5 6 8 Update Endurance Rechargeable Picture 26 05 2014 Update Technical Data 11 07 2014 Update Section 3 4 and 4 09 01 2015 Update Section 3 6 Table 10 Documentation change LOG 27
8. Physical Dimensions of the housing vsiassieedeccatteatadadsnkacdcieneiossansaaausnessaddaaasbaccansvvacatenataannnuaaeeecsaraeens 9 Figure 4 Where to insert the SIM Card Example Endurance Rechargeable eee 10 Figure 5 Plugged in SIM Card Example Endurance Rechargeable cccssccssssecsessecsseeceseeecsseeecsseeeeaes 10 Figure 6 Connecting the Battery Cables oa kdekdo bioetika 11 Figure 7 Switching the device on and off Example Endurance Primary ccc scccessecssscecesseeceseeeesseeeesaes 11 Figure 8 Connecting serial interface cable to the Endurance Primarry cssccccecsssseceessseeeecesseeeeeeeesaeeeeeees 14 Figure 9 Where to plug the configuration cable inside ccccsssecccsssscecesssecececsssaececsssaeeeceeseeeeceeseaaeeeenes 14 Figure 10 Plug inside the configuration cable si suse scun skszzbin sentai Sunceddrwasgtenavayiutecseud bee ke kaaddn saku sna 15 Figure 11 GeofentiNg ass adidas aja ka aa da udi ka oa odd apod an Gee 20 Figure 12 Installation on board Example Endurance Primary scccssscsssecesseecseseecsseeecsseeeceseeeesseeeeaes 22 1 1 Telic Telematics amp Telemetry Introduction Key characteristics of the Picotrack Endurance devices are the extremely long duration battery lifetime and low maintenance requirements The Picotrack Endurance is suited for a wide range of asset tracking applications which includes the following types of assets thi
9. Telic Telematics amp Telemetry Picotrack Endurance User Manual Version 2 6 Oe 3 St i We 6 gt S gt s ma Endurance Rechargeable 1 1 Table of Contents Introduction 1 1 Picotrack Endurance Primary 1 2 Picotrack Endurance Rechargeable Delivery content 2 1 Technical Data Operation Set up 3 1 Schematics of the device 3 2 Opening the device 3 3 Inserting the SIM Card 3 4 Connecting the Battery 3 5 Switching the device ON of OFF 3 6 Closing the device 3 7 Status indicators Configuring the unit via serial interface Troubleshooting Hints 5 1 The device doesn t show any sign of life 5 2 The device doesn t log into the GSM network 5 3 The device doesn t log into the GPRS network 5 4 The device doesn t send messages 5 5 The device doesn t receive GPS data Basic Features 6 1 Event Types 6 2 Connection Establishment Procedure 6 3 Event Message Structure Advanced Features 7 1 Geofencing 7 2 Roaming alternative configuration 7 3 Device Watchdogs 7 4 Device based wireless positioning GSM Tracking Device Installation on Board Safety 9 1 General battery handling 9 2 Battery storage 9 3 Battery disposal Telic Telematics amp Telemetry o O ON o u u N N R K NY NY N NE EEE KR EEE EEE FP E E w w W U N O O O O O NN NY o O0 60 KR NN E RP 10 General Terms and Conditions 11 CE Declaration of Conformity 12 Documentation change LOG
10. been inserted The PIN can be changed e g with a normal GSM mobile phone to 0000 To speed up the log in into the GSM network the SIM card should not contain any phone book entries 10 3 4 3 5 Telic Telematics amp Telemetry Do not touch the GPS antenna in order to avoid contamination of the receiver which may lead to a reduction of receiving quality should you be forced to clean the pad sometime please do so using pure alcohol Connecting the Battery The device is delivered by Telic GmbH with the internal battery disconnected from the electronic PCB Plug the battery inside the PCB connector as shown in Figure 6 and check that the LEDs starts blinking Figure 6 Connecting the Battery cable Switching the device ON of OFF Telic delivers the devices switched OFF To switch on the device push the small push button on the PCB until the green LED of the left GSM indicator starts to light up To switch off the device open the device and push the button twice in quick succession Figure 7 Switching the device on and off Example Endurance Primary 11 3 6 3 7 Telic Telematics amp Telemetry Closing the device Please take care that the housing covers fit together tightly and properly and that the rubber gasket is still in place With the cover in place re insert and tighten down all the screws Be careful not to over tighten the screws as it will damage the cas
11. ce Picotrack Endurance Rechargeable completely drained e g after only and wait for 3D GPS fix to synchronise the internal real several months of storage time clock Table 7 Troubleshooting Device doesn t send messages The device doesn t receive GPS data Possible issue source Trouble shooting The position of the device is Please check whether the device has the indicators facing up not favourable for the GPS and a clear view of the sky reception The GPS receiver has no free Please be aware that a GPS receiver needs always a clear view sight to the sky of the sky Please ensure that the device side with the LEDs has free view to the sky Your asset is placed in an Please consider that a GPS reception operates most efficiently unsuitable location when there is a free view of the sky If GPS reception is not available e g due to location of the asset inside a warehouse considering using the Device based Wireless Positioning feature as an alternative positioning method see Section 7 4 Table 8 Troubleshooting Device doesn t receive GPS data Further hints regarding sources of error are indicated through the 8 LEDs of the 3 indicators which are easily visible from outside You will find details for the meaning of the different colours and blinking signs in chapter 3 7 Status indicators 17 Telic Telematics amp Telemetry 6 1 6 2 6 3 Basic Features The device can be configured
12. d higher power consumption to get a fix Less precise fix The accuracy of the fix might be affected by reflections of the GPS signals It is advisable to configure in such cases the unit to perform 2D fixes No fix possible In this case it is possible to get a rough position by device based GSM tracking Picotrack Endurance Primary only but the battery lifetime of the unit will also be adversely affected 22 9 1 9 2 9 3 Telic Telematics amp Telemetry Safety The following guidelines must be followed in order to ensure the safety of users If these rules are ignored Telic will not assume responsibility for any damages that are incurred General battery handling Because the Picotrack Endurance main power source is a battery with high energy content They are designed to represent the highest possible degree of safety They may however present a potential hazard if they are abused electrically or mechanically This is in most circumstances associated with the generation of excessive heat In this case the internal pressure may cause the cell case to rupture As a result the following general guidelines should be followed when handling the Picotrack Endurance Battery Do not short circuit Do not over discharge Do not incinerate Do not expose to temperatures beyond the specified temperature range Do not crush or puncture Do not open cells do not disassemble battery packs Do not expose contents
13. e blinking of the red LED means that the SIM card is not readable e g not correctly inserted into the SIM cardholder After a certain period of time the Picotrack Endurance will switch off completely as it would be after pushing twice the red on off button Table 3 Status indicator 13 gt gt Telic Telematics amp Telemetry ry m d Configuring the unit via serial interface In order to reconfigure or read trace values from the device via the serial interface the correct cable must be plugged into the proper connector Negative consequences on safety and device integrity may occur when connecting the wrong cable to the unit and which is not listed in the Telic accessory list 1 ENDURANCE PRIMARY The device has to be opened by removing the cover lid and the cable accessory part number 16210 has to be plugged into the 6 pin white connector as shown in Figure 8 Afterwards the white button has to be pressed until the LEDs start blinking Figure 8 Connecting serial interface cable to the Endurance Primary 2 Endurance Rechargeable Open the small black lid on the top right side of the device it needs to be pulled out Figure 9 Where to plug the configuration cable inside 14 lic Telematics amp Telemetry Plug inside the configuration cable Accessory Part Number 16221 Figure 10 Plug inside the configuration cable If the device is not configured to activate by
14. hannels 22 66 tracking acquisition Battery 12 6 Ah Primary cell 13 8 Ah Lithium Polymer rechargeable Messabe Logging Jan Capacity Sleep mode average consumption GPS GSM 70 pA off Average Power consumption for one message cycle acquire position and transmission within 180 sec GSM GPS antennas Both integrated Operating temperature 30 C to 75 C 20 C to 60 C range Recharging Temperature sts 0 C to 45 C Supply voltage 5V USB Weight 550 g 550 g m ROHS ROHS Certificates re CE certified CE certified Table 2 Technical parameters for the product Telic Telematics amp Telemetry 3 Operation Set up The operation set up of the Asset Tracking device can be realized in few quick steps Please take proper measures for ESD protection e g electrical connection of the body to ground to make sure you do not destroy internal electronics Repair of ESD damages caused by user s negligence will not be covered by Telic s warranty Electrostatic discharge ESD is the sudden and momentary electric current that flows between two objects at different electrical potentials normally caused by static electricity 3 1 Schematics of the device The following figure shows the physical dimensions of the housing and should assist in mounting the device Figure 3 Physical Dimensions of the housing 3 2 Opening the device Open the Picotrack Endurance housing by removing the
15. ing and could lead to a reduction in the effectiveness of the environmental protection of the housing Please close the housing by screwing the Phillips screws down back into its original position The clear plastic light guides must be located above the LEDs Please ensure that the cover locks properly into position Min torque M 1 2 Nm Max torque M 1 5 Nm Status indicators Internally the device has three status indicators each indicator has 2 or 3 different coloured LEDs grouped close together Picotrack Endurance Primary Rechargeable Right indicator GPS This indicator includes 3 LEDs under its glass yellow green and red and reflects the status of the GPS reception as well as the device reset off GPS is not switched on 1 time blinking yellow position acquisition not possible 2 times blinking green 2D Fix no valid height and the position may be imprecise 3 times blinking green 3D Fix GPS data are complete About 5 seconds red during device reset in this case also the red LED of the middle indicator is on at the same time Middle indicator The middle indicator consists of two LEDs yellow and red Yellow LED is permanently on this indicates that the device has external power supply and the battery is currently charging only applicable for Picotrack Endurance Rechargeable If the device is in sleep mode the middle indicator works identically just the left and the right indicator are off Remark If
16. le with the Picotrack Endurance Primary A lot of other features are available on Picotrack Endurance but they are kept as confidential therefore not disclosed on this document Please contact the Telic Technical Pre Sales support in case that your specific use case requires something which you don t find described in this document 21 gt a Telic Telematics amp Telemetry Device Installation on Board The device should be installed in a location where it is well hidden in order to protect your asset from theft and vandalism Please install the device in a suitable dry location not in contact to generators of radio and audio frequency interference Be aware to observe ESD Electro Static Discharge protection measures When installing the device consider that antennas are integrated this means the device should be installed in a place with a minimum distance of 7 cm to metallic components of the asset in each direction The surface of the internal GPS antenna should be pointing skywards in order to optimize the quality of the received signal GPS Antenna Figure 12 Installation on board Example Endurance Primary The unit can also be placed on the lateral side of the Asset or even below it if the optimal installation described above is not possible Consider though that this might have the following effects Reduction of the device s battery life time due to the GPS module requiring more time an
17. n 25 11 CE Declaration of Conformity E Telic GmbH Telematik amp Telemetrie Raiffeisenallee 12b 82041 Oberhaching Telefon 089 450292 0 Telematik 4 Telemetrie Telefax 089 450292 CE Konformit tserkl rung Declaration of Conformity Hiermit wird erkl rt dass unser Produkt hereby we declare that our product Picotrack Endurance Primary den folgenden Normen und Richtlinien entspricht is in compliance with the following European Standards and regulations Nummer Kurztitel Eingehaltene Vorschriften Number Title Observed regulations R amp TTE Richtlinie 99 5 EG ETSI EN 301489 1 Electromagnetic compatibility and Radio spectrum i i V1 8 1 2010 Matters ERM EMV Richtlinie 2004 104 EG s ii EMC R amp TTE Directive 99 5 EG EMC Directive 2004 104 EG ETSI EN 301489 7 V1 3 1 2006 DIN EN 55022 VDE 0878 22 2011 12 Limits and methods of measurement it CISPR 2 DIN EN 55024 Information technology equipment VDE 0878 24 2011 0 immunity characteristics Umits and methods of measurement CISPR 24 ETSI EN 301 511 Global System for Mobile communications GSM V9 0 2 2003 Harmonized EN for mobile stations in the GSM 900 ond GSM 1800 bands covering essentio requirements of article 3 2 of the RATTE directive 1999 5 EC Oberhaching den 02 04 2014 Geschaftsfohrer Dr Ditmar Prigge BLZ 700 202 70 HRB Munchen 151080 Frank Heineck Kio 665516814 USTAD DE23266554 Swift HYVEDEMM IBAN DEO2 7002
18. ng server Therefore after switching on the device it will take approximately 2 3 minutes until the first status message can be transmitted Independent of this procedure GPS positions and status information will be generated and stored in the internal memory for later transmission Here follows the message structure Event Message Structure The first identified and valid GPS position will be taken as the reference position for the distance interval calculations The next distance interval event will be generated if the configured distance has been reached If another event e g time interval event has been generated before the distance interval measurement starts again at the position of this new event That means that any position message with an actual GPS position sets a new reference for the distance interval calculations This reduces the number of messages sent while still keeping the desired resolution of the track A position message will also be generated in the case of a direction change being greater than the configured angle while travelling at the configured minimum speed In situations where no new valid GPS position is available the last valid position will be transmitted Event Log Code Reason for the status message Event Log Timestamp Time at which the event has happened 18 Telic Telematics amp Telemetry GPS Timestamp GPS timestamp at the moment of fetching longitude and latitude Longitude Degree of longit
19. rial in the storage area Fire extinguishers for metal fire class D are preferred Do not attempt to extinguish fires with small amounts of water sand or with carbon dioxide extinguishers Battery disposal The disposal or recycling of batteries is regulated by each European country In each country the manufacturers importers and users are responsible for the proper disposal The European Community EC has issued two directives 91 157 EEC and 93 86 EEC These directives are implemented by each member country of the EC independently and in a different way In 23 Witty Telematics amp Telemetry accordance with these directives The Picotrack Endurance Batteries do not contain dangerous substances The reaction products are inorganic and do not represent environmental risks once the decomposition process has terminated 24 10 Telic Telematics amp Telemetry General Terms and Conditions All information in this documentation has been carefully assembled and checked but should not be considered as a guaranteed feature set The copyright of the related documentation is with Telic GmbH The Telic Logo and the terms Telic and Telic Picotrack are brands of Telic GmbH All further names and terms used can be brands or registered brands of their respective owners Telic preserves the right to change the included information without notice and doesn t take responsibility for errors in the document and or missing informatio
20. s list is not exhaustive Containers Freight Wagons Trailers and swap bodies Construction machines Boats Large long life and mobile industrial equipment As different applications may have similar but slightly different requirements for long term low maintenance tracking Telic offers two variants of the Picotrack Endurance the Endurance Primary and the Endurance Rechargeable While software features of both units are nearly identical they do differ in the shape of the enclosure as well as in internal hardware components Picotrack Endurance Primary The Picotrack Endurance Primary non rechargeable battery is the ideal choice for all applications with medium to low tracking frequencies and the requirement for an ultra long battery stand by time Picotrack Endurance Primary provides the following advantages Ultra long stand by time more than 8 years with 1 transmission per day Higher temperature range for operation Extremely low battery self depletion P69k housing Figure 1 Picotrack Endurance Primary Attempting to charge the primary cell can result in damage or injury 1 2 Telic Telematics amp Telemetry Picotrack Endurance Rechargeable This version is best suited for applications with higher tracking frequencies and the ability to occasionally recharge the battery Picotrack Endurance Rechargeable provides the following advantages More appropriate for higher tracking frequencies
21. screws on the outside edge of the housing see Figure below When the screws are removed lift the top of the device in order to reveal the circuit board underneath 3 3 Inserting the SIM Card A working SIM card from a suitable network provider must be properly inserted in order for the device to operate correctly Telic Telematics amp Telemetry The messages of the Picotrack are transmitted via the mobile GSM network Therefore you need a standard 3 Volts or 1 8 Volts SIM card Please give preference to post paid SIM cards To insert the SIM card first open the SIM card holder by gently sliding the top of the holder back and then swinging it into the upright position Then slide the SIM downwards direction of arrow into the top of the SIM card holder as shown in the figure below equally applicable for Picotrack Endurance Primary amp Rechargeable r a2 m BE E fa mas k Figure 4 Where to insert the SIM Card Example Endurance Rechargeable With the SIM inserted close the top of the holder and gently slide it forward direction of arrow below until it snaps into place Figure 5 Plugged in SIM Card Example Endurance Rechargeable Before the Picotrack logs into the mobile GSM network it checks whether the used SIM card is PIN free If it is PIN free it will start normal operation If the SIM card is not PIN free please ensure that the PIN is set to 0000 before it has
22. to water Do not connect with false polarity Do not weld or solder to the battery s body It is very important that only authorized official Telic replacement batteries be used in the Picotrack Endurance Rechargeable or Primary Also the batteries included with the devices are only tested or authorized for use in the Picotrack Endurance The batteries should never be used in any other devices unless specifically authorized by Telic including but not limited to other Telic products or devices No attempt should ever be made to recharge the Picotrack Endurance Primary battery This Primary cell is specifically not rechargeable and attempting to do so would be very dangerous Battery storage Batteries should be stored in rooms with generally low temperature and low humidity levels While it is not essential that these storage areas be temperature and humidity controlled temperatures should generally be kept below 35 C and storage areas should be well ventilated Storage temperatures above 75 C should be avoided Your Picotrack Endurance batteries should be stored in their original packaging materials or in the Picotrack Endurance itself This will eliminate unintentional shorting Do not store batteries in conductive anti static bags or foam unless the resistivity of the material exceeds 1 MO Batteries should not be placed on or covered with metallic or otherwise conductive material Batteries should be stored away from any flammable mate
23. ude default in 100 degrees can be decreased to 1u degrees precision Latitude Degree of latitude default in 100u degrees can be decreased to 1u degrees precision Fix Type 1 2 3 or 6 depending on the availability of satellites in view having a sufficient signal strength 1D Fix no valid data 2D Fix no height indication 3D Fix position message with height indication 6 GSM Tracking Endurance Primary only must be activated in the device Relevant for Endurance Rechargeable only 4 digits e g 0010 if charger is connected Input 1 precision of 1 10 volts Status of the motion sensor Table 9 Content description 19 7 1 7 2 7 3 7 4 Telic Telematics amp Telemetry Advanced Features In this paragraph are described some advanced features supported by the device which might be requirement for different use cases Geofencing Geofencing an electronic safety fence provides the opportunity to set a geographic square around a defined location Here you can set different scenarios like leaving the area or entering the area and transmit an event to the control centre With the Picotrack Endurance you can monitor 50 geofence areas which can also be combined to create larger areas and build up a complex protection zone Every geofence area is given an Area ID a centre defined by its longitude and latitude and a height and width from the centre not completely across in meters Figure 11
24. via serial cable by using the Telic Configuration tool otherwise remotely via SMS and GPRS Please contact Telic GmbH to have more details about the configuration procedure Event Types The Picotrack Endurance s primarily task is to transmit GPS position data including additional status information via a TCP IP connection to the tracking server If a message can t be transmitted it will be stored in the device to be transmitted later There is a storage capacity of about 1 000 position messages The following events will generate a position message which always contains the GPS position Time Event The end of a time period of x seconds x being configurable Distance Event After a distance of x meters straight line distance to the previous event in any direction x being configurable has been travelled Angular Change Event A direction change of a configurable minimum angle in x degrees x being configured at a configurable minimum speed of y km h y being configurable Connection Establishment Procedure The GSM and GPS modules will power up after switching on the Picotrack device After logging in into the GSM network the Picotrack will attempt to establish a GPRS communication link Finally a TCP IP connection to the tracking server will be established to transmit the event messages The selection of the GSM network operator will take about 1 minute plus the time to build up the GPRS and TCP IP connections to the tracki
Download Pdf Manuals
Related Search