USER'S MANUAL - UP Multimedia Service
Contents
1. Wireless DMX 512 TRANSCEIVER USER S MANUAL We congratulate you on your purchase of Wi DMX Before you proced using this product it should be necessary to read care fully the following user s manual to install it correctly and to get the best of its potentialities FRONT PANEL Shows the state of transmission receipt of the channel 1 Shows the state of transmission receipt of the channel 2 LCD display it shows all the informations on the Wi DMX functions MODE key SET key DOWN key UP key INDEX Setting of the equipment 1 1 Unpacking of the equipment 1 2 Acessories issued with the equipment and relative documentation Description of the side panel and installation 2 1 Description of the side panel 2 2 Making a DMX 512 signal cable 2 3 Input connection for power supply 2 4 Connection of the ac adapter to the electric system Initial setting 3 1 Setting of the operating mode Use of the equipment operating modes 4 1 TRANSMITTER mode 4 2 Setting of Tx1 4 3 LED 1 function 4 4 Setting of Tx2 4 5 LED 2 function 4 6 Receiver PAIRING 5 1 RECEIVER mode 5 2 State of Rx1 5 3 LED 1 function 5 4 State of Rx2 5 5 LED 2 function 5 6 Pairing with Transmitter GET PAIRING 5 7 Pairing with Transmitter GET PAIRING using Wi D PEN 6 1 EXTENDER mode 6 2 Setting of Tx1 6 3 LED 1 function 6 4 Setting of Rx2 6 5 LED 2 function 6 6 Receiver PAIRING 6 7 Pairing with Transmitter GET PAIRIN2. All rights reserved No parts of this document can be copied photocopied or reproduced without the prior written permission of the CODEM MUSIC s r l No responibility is taken for possible inaccuracies or mistakes The CODEM MUSIC s r l reserves the right to make any alterations or aesthetics changes of this product that seem necessary at any time and for whatever reason The CODEM MUSIC s r l takes no responsibility for the use or for the application of this product
3. signal Radio channel research 5 3 LED 1 FUNCTION RED Slow blinking Receiver OK no DMX 512 signal Fast blinking Channel research Switched on Receiver OK DMX 512 signal OK 5 4 STATE OF RX2 This function allows to visualize the state of the receiver of band 2 With MODE key Fig 28 find the text like in Fig 29 Reception OK Reception OK no DMX signal Radio channel research 5 5 LED 2 FUNCTION GREEN Slow blinking Receiver OK no DMX 512 signal Fast blinking Channel research Switched on Receiver OK DMX 512 signal OK 5 6 PAIRING WITH TRANSMITTER GET PAIRING This function allows to pair the Wi DMX set as receiver with a Wi DMX set as trasmitter to avoid interactions with other apparatuses of the same type For this operation you need a DMX signal cable connected between the two apparatuses Remove any cable on the DMX connectors and connect the DMX signal cable between the two apparatuses On the RECEIVER Wi DMX with MODE key Fig 29 find the text like in Fig 30 On the TRANSMITTER Wi DMX with MODE key Fig 29 find the text like in Fig 31 On the RECEIVER Wi DMX hold SET key Fig 32 until a writing appears like in Fig 33 On the TRANSMITTER Wi DMX hold SET key Fig 32 until a writing appears like in Fig 34 RECEIVER Wi DMX TRANSMITTER Wi DMX ET PAIRING Fig 30 Fig 31 PAIRING WAIT PAIRING d Fig 33 Fig 34 After a few seconds a resul
4. 12 signal OUTPUT with a 3 5 pole cannon connector Standard DMX 512 signal INPUT with a 3 5 pole cannon connector ED DMX TERMINATOR 2 2 MAKING A DMX 512 SIGNAL CABLE Wi DMX has a DMX 512 input output that uses standard XLR 5 pin or XLR 3 pin connectors The connection must be put into practice with shielded cable by these characteristics 2 conductors shield 120 Ohm impedance low capacity maximum transmission rate 250 Kbaud For the connection refer to the underlying picture XLR 3 pin Common ATTENTION the shield of the cable must never be connected to the ground of the electrical system as this could cause faults during the working of the Wi DMX 2 3 INPUT CONNECTION FOR POWER SUPPLY o g Plug the connector of the ac adapter completly in the power input amp P To disconnect it extract gently ATTENTION do not use ac adapters different from the one supplied it could cause serious damages at the internal circuitation 2 4 CONNECTION OF THE AC ADAPTER TO THE ELECTRIC SYSTEM MAKE SURE THAT VOLTAGE AND POWER FREQUENCY CORRESPOND TO WHAT IS REPORTED ON THE BALLAST PLATE The supplied ac adapter has a plug therefore you should only plug it in the socket When Wi DMX is powered the Icd display appears as in Fig 1 if this condition is not NTE LNREL EC r true please check if there is power in the electric socket or check the connection Fig 1 between ac adapter controller a
5. G 6 8 Pairing with Transmitter GET PAIRING using Wi D PEN 1 1 UNPACKING OF THE EQUIPMENT Open the box Remove the ac adapter and the documentation Take the equipment out of the box as shown in the picture below 1 2 ACCESSORI IN DOTAZIONE E DOCUMENTAZIONE RELATIVA Verify the contents of the packing If one of the following parts of the packing is missing or damaged please contact your dealer immediately Wi DMX User s manual Warranty Ac adapter mod 1882108 1 XLR 3 5 P male connector e 1 XLR 3 5 P female connector Read the following warnings before beginning installation e This unit is not intended for home use e Read this manual thoroughly and observe the following precautions before working with the Wi DMX e Take care not to spill liquids on to the controller and do not use it in excessively humid conditions e Do not install Wi DMX near heat sources or expose it to direct sunlight and do not install in dusty environments without suitable protection e Do not use Wi DMX unless the ac adapter cable and plug are in perfect condition replace or repair if necessary e Do not use solvents such as acetone or alcohol to clean the controller or the finish and panel lettering will be damaged e If a fault occurs consult your nearest service centre or a specialized light equipment repair service Do not attempt to repair the controller yourself 2 1 DESCRIPTION OF THE SIDE PANEL y O EB Standard DMX 5
6. arching until they find the new Radio channel 4 3 LED 2 FUNCTION GREEN Slow blinking Transmitter OK no DMX 512 signal Switched on Transmitter OK DMX 512 signal OK 4 6 RECEIVER PAIRING This function allows to pair the receiver Wi D Pen to the transmitter Wi DMX to avoid interactions with other apparatuses of the same type With MODE key Fig 1 7 find the text like in Fig 18 Connect Wi D Pen to the DMX 512 transmitter signal IN Fig 20 1 without connecting Wi D Pen ac adapter Hold SET key Fig 19 until a writing appears like in Fig 20 PAIRING WAIT 7 Fig 20 Fig 20 1 After a few seconds a result of the operation is given if like in Fig 21 pairing succeeded else the message of Fig 22 appears PAIRING lt Fig 21 PAIRING 5 1 RECEIVER MODE This operation mode allows you to receive the DMX 512 signal coming from a Wi DMX transmitter and provide it to the connected projectors The connection must be like in Fig 23 In this mode switch terminator to ON Wi DMX receives the Radio signal and shows the number of channels generated Fig 24 in absence of Radio or DMX signal the display CH appears like in Fig 25 DMX to other Terminator projector OMX lt NO DAT 5 2 STATE OF RX1 This function allows to visualize the state of the receiver of band 1 With MODE key Fig 26 find the text like in Fig 27 Reception OK Reception OK no DMX
7. nd ac adapter electric socket If the problem persist please consult your dealer 3 1 SETTING OF THE OPERATING MODE The Wi DMX factory default mode is TRANSMITTER REGARDLESS OF THE MODE YOU MUST EXECUTE THE PAIRING OPERATIONS EXPLAINED IN THE RELATIVE CHAPTERS OF THIS MANUAL This procedure allows to change between TRANSMITTER RECEIVER EXTENDER mode of operationa Power down the Wi DMX g While holding down SET key Fig 2 Power up the Wi DMX The lcd display appears as in Fig 3 Use UP DOWN keys to change operating mode Confirm with SET key Fig 2 4 1 TRANSMITTER MODE This operation mode allows you to transmit the DMX 512 signal coming from a con troller to the paired receivers through two channels of transmission The connection must be like in Fig 4 Wi DMX analyzes the DMX 512 signal as soon as the XLR connector is inserted and shows the number of channels generated from the controller Fig 5 in absence of signal the display appears like in Fig 6 DMX coming from controller DMX to other i projectors Fig 4 4 2 SETTING OF TX1 This function allows to set the range of DMX channels to transmit on band 1 RED LED to the paired receivers and the RADIO channel to use among the ten available from OR to 9R With MODE key Fig 7 find the text like in Fig 8 To change the setting hold SET key Fig 9 until the first value starts blinking Fig 10 Use UP DOWN keys to change
8. nels to transmit on band 1 RED LED to the paired receivers and the RADIO channel to use among the ten available from OR to QR With MODE key Fig 46 find the text like in Fig 47 To change the setting hold SET key Fig 48 until the value starts blinking Fig 49 Use UP DOWN keys to change the value Fig 50 When finished confirm with SET key Fig 48 It is advisable not to use the same Radio channel found by the receiver N B If you get problem of transmission try changing the Radio channel When Radio channel is modified receivers start searching until they find the new Radio channel 6 3 LED 1 FUNCTION Slow blinking Transmitter OK no DMX 512 signal Switched on Transmitter OK DMX 512 signal OK N B If a Radio channel between OR and 9R is used the led is Red If a Radio channel between OG and 96 is used the led is Green 6 4 SETTING OF RX2 This function allows to visualize the state of the receiver and to change the receiver band With MODE key Fig 51 find the text like in Fig 52 To change the receiver band hold SET key Fig 53 until the value changes Fig 54 J Reception OK Reception OK no DMX signal Radio channel research Radio band changed 6 5 LED 2 FUNCTION Slow blinking Receiver OK no DMX 512 signal Fast blinking Channel research Switched on Receiver OK DMX 512 signal OK N B If a Radio channel between OR and 9R is used the led is Red If a Radi
9. o channel between OG and 9G is used the led is Green 6 6 RECEIVER PAIRING This function allows to pair the receiver Wi D Pen to the TX1 of the Extender Wi DMX Follow the instructions at v par 4 6 6 7 PAIRING WITH TRANSMITTER GET PAIRING This function allows to pair the RX2 of the Extender Wi DMX with a Wi DMX set as trasmitter Follow the instructions at v par 5 6 6 8 PAIRING WITH TRANSMITTER GET PAIRING USING WI D PEN This function allows to pair the RX2 of the Extender Wi DMX with a Wi DMX set as trasmitter using Wi D PEN Follow the instructions at v par 5 7 Wi DMX TECHNICAL FEATURES Technical features Signal Output signal DMX512 1990 Input signal DMX512 1990 Output connector 3 5 pin cannon connector female Input connector 3 5 pin cannon connector male Max number of projectors connected to the DMX output 32 Technical features Radio Frequency range 2 4 GHz 2 483 GHz ISM Number of channels 20 Transmitter range 1000 meters 3280 ft open air Climatic condition for the use Humidity 35 80 Temperature 5 50 C Power supply Voltage current 9 Vdc 550 mA Dimensions and weight Dimension W x L x H Weight 113 x 224 x 45 mm 0 9 Kg CE01220 C FCC ID RBKUGWR2USXXXX Canadian Cert No IC 5125A UGWR2US CODEM MUSIC S r l Via G Pierini 13 61100 PESARO ITALY Tel 39 0721 204357 Fax 39 0721 203554 http www codemmusic com E mail info 4codemmusic com
10. t of the operation is given if like in Fig 35 on both apparatu ses pairing succeeded else the message of Fig 36 appears PAIRING lt Fig 35 PAIRING FAILED Fig 36 5 7 PAIRING WITH TRANSMITTER GET PAIRING USING WI D PEN This function allows to pair the Wi DMX set as receiver with a Wi DMX set as trasmitter For this operation you need a Wi D PEN already paired with the trasmitter Wi DMX v par 4 6 With MODE key Fig 37 find the text like in Fig 38 Connect Wi D Pen to the DMX signal input without connecting Wi D Pen ac adapter Hold SET key Fig 39 until a writing appears like in Fig 40 AIRING Fig 38 PAIRING WAIT Fig 40 After a few seconds a result of the operation is given if like in Fig 41 pairing succeeded else the message of Fig 42 appears PAIRING lt Fig 41 PAIRING FAILED Fig 42 6 1 EXTENDER MODE This operation mode allows you to receive the DMX 512 signal coming from a Wi DMX transmitter provide it to the connected projectors and re transmit it to other receiver apparatuses The connection must be like in Fig 43 In this mode switch terminator to ON Wi DMX receives the Radio signal and shows the number of channels generated Fig 44 in absence of Radio or DMX signal the display m appears like in Fig 45 i DMX to other Terminator projector 6 2 SETTING OF TX1 This function allows to set the range of DMX chan
11. the value Fig 11 Use MODE key to move to the next value Fig 7 When finished confirm with SET key Fig 9 Fig 10 The range of DMX channels to transmit must correspond to the chan nels used by the projectors connected to the paired receivers on band 1 You should set such projectors on consecutive DMX addresses N B If you get problem of transmission try changing the Radio channel When Radio channel is modified receivers start searching until they find the new Radio channel 4 3 LED 1 FUNCTION RED Slow blinking Transmitter OK no DMX 512 signal Switched on Transmitter OK DMX 512 signal OK 4 4 SETTING OF TX2 This function allows to set the range of DMX channels to transmit on band 2 GREEN LED to the paired receivers and the RADIO channel to use among the ten available from OG to 96 With MODE key Fig 12 find the text like in Fig 19 To change the setting hold SET key Fig 14 until the first value starts blinking Fig 15 o Use UP DOWN keys to change the value Fig 16 Use MODE key to move to the next value Fig 12 When finished confirm with SET key Fig 14 The range of DMX channels to transmit must correspond to the chan nels used by the projectors connected to the paired receivers on band 2 You should set such projectors on consecutive DMX addresses N B If you get problem of transmission try changing the Radio channel When Radio channel is modified receivers start se
Download Pdf Manuals
Related Search