User's Manual - Glasfaserinfo
Contents
1. by 16 24 32 Port 10 100Mbps Fast Ethernet Switch ES 3116RL ES 3124RL ES 3132RL User s Manual Ea CO bat 5 0 us an Sn K an vnd LLI vnd Y 5 0 TE Tr E nA AA Y FCC COMPLIANCE STATEMENT This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the instructions provided with the equipment may cause interference to radio and TV reception The equipment has been tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection against such interference in a commercial environment However there is no guarantee that interference will not occur in a particular installation If you suspect this equipment is causing interference turn your switch on and off while your radio or TV is showing interference to determine the source of the interference You can try to correct the interference by one or more of the following measures 1 Reorient the receiving radio or TV antenna where this may be done safely 2 To the extent possible relocate the radio TV or the other receiver away from the equipment 3 Plug the computer which has the equipment installed into a different power outlet so that equipment and the receiver are on different branch circuits If necessary you should consult the place of pur2. loss Importantly 1 rovide Auto MDI MDI X function on all UTP port so you don t need to worry bout whether the cable is normal or cross over type And it offers the best way to relieve bandwidth bottlenecks and provide faste esponse times for networked users his switch is typically used to segment network traffics that can improve the 1etwork performance by increasing the total bandwidth as illustrated in Figure 1 1 200Mbps 100Mbps 100Mbps Figure 1 1 Increase network bandwidth 1 Features Comply with IEEE 802 3 10BaseT Ethernet and 802 3u 100BaseTX Fast Ethernet standards Simple and economical way to bridge 10BaseT network and 100BaseTX network TEEE 802 3x compliant flow control for full duplex and Backpressure for half duplex All of RJ 45 ports support 10BaseT 100BaseTX and Full Duplex Half Duplex Auto negotiation function All of RJ 45 ports provide Auto MDI MDI X function Extensive front panel diagnostic LEDs Support store and forward switching architecture 19 rackmount designed B Standards IEEE 802 3 10BaseT and 802 3u 100BaseTX E 10 100Mbps UTP Ports ES 3116RL RJ 45 x 16 with Auto MDI MDI X ES 3124RL RJ 45 x 24 with Auto MDI MDI X ES 3132RL RJ 45 x 32 with Auto MDI MDI X B Switching Architecture Store and Forward E Filter Forward Rate 148 800 packets sec EMAC A
3. IACT L Fast Ethernet Ns LED LNK ACT LED 3132RL L Power LED Rear View GD S Power Connector A E E PWR Power LNK ACT E Table 4 1 LED description 10 100M Operating Environment This switch must be installed and operated within the limits of specified operating emperature and humidity see previous section under Specifications Do not place ybjects on top of the unit Do not obstruct any vents at the sides of the unit Do not position the unit near any heating source such as heater radiator or direct exposure o sun Prevent entering of water and moisture into the unit If necessary use lehumidifier to reduce humidity Connecting to network devices The RJ 45 ports on the switch are designed as Auto MDI MDI X ports whether the able is straight through or cross over type this switch could connect with vorkstation or other switch hub easily Connect one end of the network cable to the RJ 45 port on the front panel and onnect the other end of the network cable to the RJ 45 port on the network device ollowing the same procedure to connect all the RJ 45 ports of the switch The UTP 1etwork cables must comply with EIA TIA 568 specifications and Category 5 standard for 100Mbps data transmission Maximum length using UTP cable yetween the switch and connected device is 100 meters 300ft 3 Connecting the power Connect the power cord to the power socket on the rear panel of the un
4. chase or an experienced radio television technician for additional suggestion CAUTION The phone jack cannot be connected to telephone system Chapter Chapter Chapter Chapter Chapter Chapter Chapter l 2 3 4 5 6 E Contents Introduction resi is l Features amp Specifications 2 Package Contents 4 Physical Description 5 RED Status maak Ma vaantialaaa vasest 1 stato Rd 8 Trouble shooting 9 Congratulations on your purchase of this Fast Ethernet Switch This higt yerformance switch provides Fast Ethernet ports to segment network traffics extenc ast Ethernet connection distance and convert data packets between differen ransmission speeds This switch utilize stored and forward switching architecture that filters and forward lata after the complete data packet is received and examined to be free of errors With one set of status LEDs for each individual port the switch operation status car je easily monitored t s rackmount design that can be mounted on the industrial standard 19 inches rack n the enterprise wiring center All of UTP ports support full amp half duplex which are able to provide 200Mbps o yandwidth The auto negotiation function providing smooth migration from Etherne o Fast Ethernet It also supports backpressure and IEEE 802 3x advanced flow ontrol capability that can reduce congestion and prevent packet
5. ddress ES 3116RL 8K ES 3124RL 4K ES 3132RL 4K E Buffer Memory ES 3116RL 512KByte ES 3124RL 768KByte ES 3132RL 1MByte B Nway Auto negotiation all ports B Full Duplex Half Duplex all ports B Switch LED Power B Port LEDs Link Activity Collision Full Duplex 10 100M E Dimensions 440 x 172 x 45 mm 17 3 x 6 8 x 1 75 inches E Weight 2 4kg 5 3 lb B Power 100 240V AC full range internal power supply B Oneratino Temneratire 29 1210E 0 5500 E One Fast Ethernet Switch E One power cord E One user s manual E Rackmount accessories S 3116RL S 3124RL S 3132RL E T Eo ia Ad Pii alo puss aen ae sis 1 Panel 10BaseT 100BaseTX Por Front View _ COL FDX LED 80000400 rwo 22222902 Switch 00000000 rwo Fast Ethernet RO L Power LED 100Mbps LED LNK ACT LED Rear View Power Connector SY 10BaseT 100BaseTX Port Front View i 3 ratte FDX LED 3124RL witch ast Ethernet kii LNK ACT LED Rear View Power Connector Fast Ethernet Front View so COL FDX LED COL M
6. it Connect he power cord to the power outlet and turn on power switch The green Power LED m the front panel should be lit Figure 5 5 Connect the power cable e Y Power LED is not lit Check ifthe power cord 1s properly connected to the power outlet and the hub Make sure the power switch on the hub is turned ON 100M UTP Link is not lit when connect to 100 Mbps device Check the power switch of the network device attached to the switch make sure it is turned ON Check the network cable make sure it is properly connected to the switch and the network device 3 UTP Collision LED flashes constantly Remove all the network cables then plug in the cables to isolate the source of the collision Check the network cable inferior cable quality will result in excessive collision and error packets 1 Contact your dealer if problem persist
Download Pdf Manuals
Related Search