VMT8000 series EN User Manual - ads-tec
Contents
1. VMT8000 series 24 6 Putting into operation 6 1 Scope of delivery Please check that all of the following components are contained in the packaging e 1 x device e 1 x 4 pin plug for power supply in service slot Optional scope of delivery e Operating system license opt DVD e Installation kit for brackets e Power adapter with power cable and 4 pin plug for power supply e ads tec cable kit for forklifts depending on operating system 6 2 Check for operational readiness Check the device to determine whether hidden damages have been caused by improper transport incorrect operation storage conditions or improper handling If you find any damage contact the manufacturer immediately The device must not be put into operation The power supply and the device interfaces are located in the service slot lt has to be removed in order to connect the power supply lead and the interface cables Allnecessary cables must be connected at the beginning of commissioning Hazard due to condensation Damage to electronic components caused by condensation resulting from temperature fluctuations The device should only be switched on after it has acclimated to the ambient temperature To avoid overheating in operation The device must not be exposed to direct radiation by sunlight or any other heat source Damage due to electrostatically sensitive components Damage to the device can be caused by electrostatically se2. ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 39 10 Software amp driver installation The device is equipped with a touch screen monitor The touch screen is connected internally via the USB interface The driver software necessary for use as well as the software for the soft keyboard are already included in the respective operating system Inthe case of devices without preinstalled operating system the drivers software can be downloaded from the website Recommendation for use If the hard drive has been reformatted the operating system can be reinstalled by using one of the existing interfaces An external keyboard is required for installation Installing the operating system The device does not have any integrated CD drive The installation of the operating system can therefore only be carried out by using the USB interface Procedure for installation e The boot drive in the system Bios must be switched to USB in order to boot the device from the USB interface e Restart the device and insert a Windows CD e Install Windows and set up the basic data e With devices including touch screens the touch screen driver as well as the soft keyboard should be installed in order to ensure their full functionality ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 11 Maintenance 11 1 Information on maintenance Maintenance should be performed on
3. The USB interfaces are used for connecting peripherals with USB connection These interfaces comply with the USB 2 0 standard requirements PIN number Signal name 1 VDC i VER 2 D 3 D 4 GND 4 4 1 Service slot There are 3 USB connections in the service slot of the device 4 4 2 Front panel There is a USB interface on the front side It is protected against dust and dirt by a cover Recommendation for use The device supports a maximum of 8 external USB mass storage devices If a USB Flash SSD is installed amaximum of 7 USB mass storage devices can be connected Recommendation for use The USB interfaces can be individually locked by using the Lock USB software tool Recommendation for use It should remain closed when not in use in order to ensure the IP protection ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 16 4 5 Network connection If the drivers required for functioning are installed on the device the control system may be integrated in an Ethernet network supporting the 10 100 1000Mbit standard by using the Ethernet 10 100 1000 BaseT network connector The specifications of this network topology must be observed If the drivers necessary for the function are not installed they can be downloaded from the website www ads tec de 110 100Mbit Pin Nummer Signal Name 1 TX 1 8 2 TX 3 RX 4 NC 5 NC 6 RX 7 NC 8 NC 1000 BaseT Pin N
4. active state alohanumeric numeric keys or function keys will be stored and will be displayed when re activating the keyboard Recommendation for use The functional description of the program Soft keyboard can be found in the chapter of the same name for the Configuration Center 7 3 Touch screen The control system is equipped with a touch screen monitor The driver software necessary for use is already included in the respective operating system or can be downloaded from the company s website www ads tec de ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 31 7 4 Status displays SYS LED bicoloured Depending on the colour and type of flashing different device states are displayed by the SYS LED System LED The following signals are displayed System LED indicators Behaviour Description green Device is connected to a power static supply and switched on orangeffl Volume display brightness is ashing being modified orange Minimum maximum value for static volume display brightness is reached ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen acis tec VMT8000 series 32 7 5 Speakers The VMT8000 devices have two internal speakers Speaker positions The volume can be set up by using the device front keys When activating the described key combinations the volume level is modified accordingly If the soft keyboard has been installed the
5. must be shut down immediately Ensure that it is secured against being started up accidentally 3 3 Warranty repairs During the device warranty period any repairs must only be performed by the manufacturer or by service personnel that has been authorised by the manufacturer 3 4 Intended use The device is used for visualisation and control as well as the acquisition of operating and machine data in the production environment Another typical application is in logistics Here the device can be used for mobile data acquisition The device is only to be assembled installed and operated within the permissible specifications Use in non specified environments is prohibited 3 5 Improper use Operation other than or beyond that described for the device shall be deemed improper use The device is not allowed to be used to control vehicles or for applications for which further approvals beyond the manufacturer s declaration are necessary e g applications with explosion hazard medical technology shipping industry The device must not be put into operation in the case of transport damage or nonconformity with the specifications and if necessary must be taken out of operation in the case of changing conditions In the case of improper use ads tec shall not accept responsibility or liability for injury or damage that is directly or indirectly attributable to the handling of the device Should the device have evident signs of damages cause
6. possible 13 2 Company address ads tec GmbH Heinrich Hertz Str 1 72622 N rtingen Germany Phone 49 7022 2522 0 Fax 49 7022 2522 400 Email mailbox ads tec de Web www ads tec de ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec
7. ATA 8 16 32 120 GB Alternatively 2 5 automotive hard disk with a minimum of 80 GB SATA 2 5 SSD 8 16 32 64 GB Interfaces COM 1 RS232 5V supply can be activated for scanner 1 x USB 2 0 in front panel 3 x USB 2 0 All external USB interfaces in high current design up to 1A Optional COM2 RS232 RS485 or CAN Network 2 x Ethernet 10 100 1000Mbit RJ 45 Sound Sound output via two internal speakers Wireless Optional Integrated WLAN module 802 11 a b g n with 3 WLAN antennas for 3 x 3n Optional Connection for external antenna R SMA connector in service slot Power adapter 24 V DC 48 V DC Typ power Typ 0 80 A Typ 1 10 A Typ 1 20 A Typ 1 30 A Operating system Windows 7 Embedded Windows Embedded 8 1 Industry Pro Windows 7 Ultimate Protection class IP65 Operating temperature 20 to 55 C depending on mass storage device Optional 30 to 55 C depending on mass storage medium Dimensions W x H x D 259 x 187 x 60 mm 299 x 246 x 60 mm 344 x 266 x 57 mm 405 x 310 x 61 mm Weight Approx 2 2 kg Approx 3 1 kg Approx 3 5 kg Approx 4 5 kg Vibration and shock resistance EN 60721 3 5 06 1998 class 5M2 for HDD version class 5M3 terrestrial vehicles for SSD version 5 hours of noise type vibrations 3 6 g rms and 30 g peak value MIL STD 810F 01 2000 Annex C Fig 514 5C US Highway Truck Transportation Humidity 10 to 85 non condensing The figures given for the typ current con
8. N rtingen e tec VMT8000 series 26 6 6 Available interfaces Service slot No Designation Description 1 X1 PE OV IGN 24V DC IN optional X1 PE OV IGN 48V 2 S1 AUTOSTART Autostart function OFF ON 3 X2 WLAN Preparation for ext WLAN S2 COM 5V OFF ON 5V connection at port COM1 4 X3 COM COM1 port RS232 5 X4 LAN1 LAN ports RJ45 10 100 1000 Mbit X5 LAN2 6 X6 USB1 USB ports USB 2 0 X7 USB2 X8 USB3 7 Cable entry grommets seals The power supply is realized by means of a transformer The primary side of the transformer which is connected to mains is electrically insulated from the secondary side of the transformer which provides the internal power supply Functional EMC protection is provided only if the PE pin of the power supply plug is connected to earth When mounting on mobile vehicles a functional earth must be established for this purpose ads tec GmbH e Heinrich Hertz Str 1 72622 N rtingen e itec VMT8000 series 27 The device is designed for an LPS supply LPS Class2 Hazard due to damage to device Damage caused by connected peripherals or data loss All cable lines power supply interface cables should only be connected while the device is switched off and de energised ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 28 7 Operation 7 1 Front Panel Operation Keys Fig 6 Depending on the device version an operating system and
9. Version 2 2 Instruction manual Terminals VMT8000 series Industrial IT Effective as of 06 07 2015 VMT8000 series 1 Table of Contents 1 Notes 3 1 1 General remark 3 1 2 Limitation of liability 3 1 3 Manufacturer 3 1 4 Relevant device documentation 3 D 2 Safety instructions 2 1 Structure of safety instructions 4 2 2 Graduation of risk level 4 2 3 Explanation of used symbols 4 2 4 Symbols 5 2 5 Data figures and modifications 5 2 6 Trademarks 5 2 7 Copyright 5 2 8 Environmental conditions 6 2 9 Standards 7 3 Operating and safety instructions 8 3 1 Operating location 9 3 2 Damage due to improper use 9 3 3 Warranty repairs 9 3 4 Intended use 9 3 5 Improper use 9 3 6 Treatment and disposal of lithium batteries 10 3 7 Safety instructions 10 4 Product description 11 4 1 Device features 11 4 2 24 V 48 V DC power supply 13 4 2 1 Release contact IGN 14 4 3 Autostart function 15 4 4 USB connections 15 4 4 1 Service slot 15 4 4 2 Front panel 15 4 5 Network connection 16 4 6 Serial interface COM1 17 4 7 Heater optional 17 5 Assembly 18 5 1 External device dimensions VMT8008 20 5 2 External device dimensions VMT8010 21 5 3 External device dimensions VMT8012 22 5 4 External device dimensions VMT8015 23 ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e ttec VMT8000 series 2 6 Putting into operation 24 6 1 Scope of delivery 24 6 2 Check for operational readiness 24 6 3 Order of steps dur
10. al is protected by copyright For the authorised user simple usage rights are granted within the scope of the intent of the contract Any modified use or exploitation of the provided content particularly duplication modification or publishing in whatever form is permitted only with the prior consent of ads tec In the case of copyright infringement ads tec reserves the right to exercise all rights ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 2 8 Environmental conditions The device can be put into operation and used under the following conditions Failure to observe any one of these conditions will invalidate the warranty ads tec cannot be held liable for any damages arising from improper use and handling e Temperature for devices without a heater in operation 20 BBC for storage 30 60 C e Temperature for devices including a heater in operation 30 55 C for storage 30 60 C e Humidity In operation 10 85 without condensate For storage 10 85 without condensate e Air quality Air pollution level 3 or lower according to This device is compliant to the DIN EN 60068 2 27 shock and bump testing specification e Vibration and shock resistance EN 60721 3 5 06 1998 class 5M2 for HDD version class 5M3 terrestrial vehicles for SSD version 5 hours of noise type vibrations 3 6 g rms and 30 g peak value Additionally applies MIL STD 810F 01 2000 annex C f
11. anner if voltage is no longer present at the ignition contact Prefabricated supply cables are available from ads tec for using the ignition function Recommendation for use Switching the device on or off by using the ON OFF pushbutton will override the ignition function That means if the device is switched off by using the Power button the system is shut down and can be restarted by using the Power button However it can also be restarted by using the ON OFF function of the ignition Hazard due to overvoltage There is an acute risk of irreparable damage if the permissible threshold is exceeded Do not operate on vehicles that exceed the permissible system voltage The following thresholds for system voltage must be observed 24V DC system voltage 5V DC 36V DC 48V DC system voltage 5V DC 60V DC Recommendation for use gt The ignition function must never be used together with the autostart function Recommendation for use gt The functional description of the program Ignition Key Locking can be found in the chapter of the same name ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 15 4 3 Autostart function The autostart function allows the automatic start up of the device upon application of the supply voltage of 24V 48V DC Information The Autostart switch in the service slot must be set to ON in order to use this function 4 4 USB connections
12. configuration of the front buttons is already installed ex works ON OFF pushbutton of the device ATX functionality The operating system is shut down but the device is not disconnected from the input voltage Level 1 Activate and deactivate the soft keyboard for letter character input using the touch screen Level 2 Decrease display brightness B Level 1 Change task Alt ESC in Windows Level 2 Increase display brightness Level 1 Not allocated The configuration of this level can be customised by programming via the soft keyboard program in the configuration center Level 2 Decrease the volume of the internal speakers Level 1 Right mouse key function Level 2 Increase the volume of the internal speakers Capacitive Shift key SHIFT for activating the second keyboard level This key must be pressed simultaneously with the desired function key ae Da BE Resistive The Shift key needs to be pressed Afterwards the desired function key can be pressed ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 29 volume control are active If the values are changed no visible change takes place on the display The key functions can have been previously modified in accordance with customer specific requirements The above described Recommendation for use gt If the soft keyboard is not installed only the functions for display settings and func
13. d e g by improper operation or storage conditions or due to improper use or handling it must be shut down immediately Ensure that it is secured against being started up accidentally ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 10 3 6 Treatment and disposal of lithium batteries This device contains a lithium battery for supplying the system clock with power as long as the supply voltage is not connected The battery has a life cycle of 3 5 years depending on which load is applied Hazard due to thermal loads The more the battery is exposed to higher temperatures the faster it ages Avoid thermal loads Hazard due to explosion Danger of explosion if using incorrect battery types Use the battery type recommended by the manufacturer Lithium batteries should not be exposed to fire soldered recharged opened short circuited reversed or heated above 100 C and they should be disposed of properly as well as protected against sunlight moisture and condensation The battery type to be used is 2 AA 3V Lithium Battery Type FDK Corp CR14250SE ads tec part number DZ SONS 041 00 0 The used lithium battery should be disposed of in accordance with local legal regulations 3 Safety instructions Damage due to electrostatically sensitive components Damage to the device can be caused by electrostatically sensitive components All installation and service wo
14. ed by using a soft cloth and a commercially available glass cleaning agent e g Sidolin with low alcohol content Hazard due to damage to device Damage caused by connected peripherals or data loss All cable lines power supply interface cables should only be connected while the device is switched off and de energised ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 9 3 1 Operating location The device is designed for use on support arm systems wall and table mounting or on vehicles commissioning trolleys forklifts or similar You have to take care that the environmental conditions specified in the technical data are met Use in non specified environments i e on board ships in explosive atmospheres or at extreme elevations is prohibited The device must not be used to control vehicles It must be ensured that the device is installed properly Hazard due to condensation Damage to electronic components caused by condensation resulting from temperature fluctuations The device should only be switched on after it has acclimated to the ambient temperature To avoid overheating in operation The device must not be exposed to direct radiation by sunlight or any other heat source 3 2 Damage due to improper use Should the control system have evident signs of damages caused e g by improper operation or storage conditions or due to improper use or handling the device
15. g steps before starting commissioning via software in order to exclude any possible transport damages or other error sources Depending on hardware equipment a MIFARE or LEGIC RFID reader is installed 8 4 1 MIFARE To test the RFID function select the ads tec RFID example application via the pre installed Configuration Center Recommendation for use Detailed information on the Configuration Center can be found in chapter Configuration Center Ads tec RFID Reader tool This application is configured automatically i e when the program is started all COM ports are searched for the RFID reader Suche nach RFID Leseger t RFID Leseger t gefunden an COM Schnittstelle 5 Bitte den Transponder an die markierte Stelle halten Fig 7 If an RFID reader was detected the device cyclically queries to check whether a serial number CSN was read If a transponder serial number is read during this process it is output directly on the user interface ads tec GmbH Heinrich Hertz Str 1 72622 N rtingen ete itec VMT8000 series 37 If no RFID reader was found one has the option to select the serial interfaces at which the RFID reader IS connected COM Port COM2 2 Suche nach RFID Leseger t Kein RFID Leseger t gefunden Fig 8 After the COM port is selected the application opens the interface which is then ready to receive data The data from a transponder are output o
16. here is a danger of overvoltage at the device Always attach the protective earth The power supply is realized by means of a transformer The primary side of the transformer which is connected to mains is electrically insulated from the secondary side of the transformer which provides the internal power supply Functional EMC protection is provided only if the PE pin of the power supply is connected to earth When mounting on mobile vehicles a functional earth must be established for this purpose The UL marking only applies to 24 V DC power supply ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 14 4 2 1 Release contact IGN The device is capable of being externally started by using an additional signal input This function is well known from the automotive industry switch on by using an ignition contact The device is here continuously supplied with a 24V 48V DC power supply and only if the additional signal is present at the ignition contact e g as a result of turning the ignition key of the forklift the computer is switched on or the blocking is released This function protects the system from unauthorised use If the device is installed onboard of vehicles or other mobile and battery driven equipment the ignition function also saves energy This function can be configured by using the Ignition Key Locking software tool For example the computer can be shut down in a time controlled m
17. iate measures and to pay any costs incurred as a result ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 3 Operating and safety instructions The device operates under electrical voltage and contains highly sensitive components Intervention by the user is required only for connecting the power supply lines Should any further modifications be required it is necessary to consult either with the manufacturer directly or with service personnel authorised by the manufacturer The device must be de energised during work Appropriate measures must be taken to prevent electrostatic discharges on components Ifthe device is opened up by an unauthorised person the user may be subject to hazards and the warranty is invalidated General information e All users must read this manual and have access to it at all times e Assembly commissioning and operation may only be performed by qualified and trained personnel e The safety notices and the manual itself must be observed by all persons who work with this device e At the installation site the valid guidelines and regulations for accident prevention must be observed e The manual contains the most important instructions on how to use this device in a safe way e Appropriate storage proper transport installation and commissioning as well as careful operation are prerequisites for ensuring safe and proper operation of the device e The device can be clean
18. igure 514 5C US highway truck transportation depending on mass storage device The UL marking applies for operating temperatures up to max 40 C and for devices without heater ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 2 9 Standards This device is compliant with the provisions and safety objectives of the following EU directives Standards e This device is compliant with the CE mark test requirements as defined in the European test standards EN 55022 and EN 61000 6 2 e This device is compliant with the DIN EN 60950 VDE0805 IEC950 testing specifications on Information technology equipment Safety e This device is compliant with the DIN EN 60068 2 6 testing specifications sinusoidal vibration e This device is compliant to the DIN EN 60068 2 27 shock and bump testing specification By using the CE conformity declaration in this document you can find detailed information about the standards applicable to this device For full compliance with the EMC legislation all components and cables used for device connection must also be compliant with these requirements Recommendation for use Always use shielded bus and LAN cables with shielded plugs Interference in residential environments This is a class A device Class A devices may cause interference when used in residential environments In this case the operator can be requested to take appropr
19. ing commissioning 25 6 4 Operation 25 6 5 Taking out of operation 25 6 6 Available interfaces 26 7 Operation 28 7 1 Front Panel Operation Keys 28 7 2 Soft keyboard 29 7 3 Touch screen 30 7 4 Status displays 31 7 5 Speakers 32 8 Wireless 33 8 1 WLAN optional 33 8 2 Bluetooth optional 34 8 3 RFID reader as an option 35 8 4 RFID configuration 36 8 4 1 MIFARE 36 8 4 2 LEGIC 37 9 Drives 38 10 Software amp driver installation 39 11 Maintenance 40 11 1 Information on maintenance 40 11 2 Information on storage 40 12 Technical details 41 13 Service amp support 42 13 1 ads tec support 42 13 2 Company address 42 ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye ttec VMT8000 series 3 1 Notes 1 1 General remark This instruction manual is intended to ensure safe and efficient handling of the device It must be accessible to all persons who are involved in installation and commissioning of the device and must be read and understood before any work is started The instruction manual must be passed on to the device system operator after commissioning has been completed All of the safety notices and handling instructions given in the manual must be obeyed in order to ensure that work is carried out safely Figures used in this instruction manual are provided for basic understanding and may differ from the actual design The original version of this instruction manual was written in German All non German versi
20. ion ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 2 Safety instructions 2 1 Structure of safety instructions The signal word classifies the hazard Reference to the type consequences and source of the hazard is made underneath the signal word Instructions for preventing the hazard are identified by an arrow SIGNAL WORD Type consequences of hazard Source of hazard Measures to prevent hazard 2 2 Graduation of risk level The signal word classifies the hazard Instructions for preventing the hazard are identified by an arrow 2 3 Explanation of used symbols Indicates an imminent danger If not avoided death or severe injury will result Indicates a possible danger If not avoided death or severe injury could result Indicates a possible danger If not avoided light or minor injuries could result Indicates a possibly damaging situation If not avoided the system or something in its surroundings could be damaged Recommendation for use The symbol Recommendation for use indicates terms and or conditions that Strictly need to be observed to ensure optimised and or zero defect operation Tips and suggestions for the efficient use of the device and software optimisation are also provided ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 2 4 Symbols Symbol Meaning Designation of batteries i
21. ly by qualified electricians certified by ads tec 40 The following components of the system are maintenance parts Use dry cleaning cloths to clean the system Component Type of maintenance BIOS battery Replace 1 2 AA 3V buffer battery Type FDK Corp CR14250SE ads tec part number DZ SONS 04100 0 Fuse Replace 7A 32Vdc Littelfuse INC F200 F1200 Type 453007 Exterior Clean device with dry cloth Earth Secure connection and connections correct operation 11 2 Information on storage Maintenance interval 3 years Replace only if damaged As necessary dependent on installation site According to VDE0113 Always observe the environmental conditions for storing batteries no direct sun light dry room no frost ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen VMT8000 series 41 12 Technical details Device data VMT8008 VMT8010 VMT8012 VMT8015 Housing Diecast aluminium powder coated Front panel 3 mm glass panel toughened and anti reflective Display 8 TFT 10 4 TFT 12 1 TFT 15 1 TFT Resolution 800 x 480 pixels 1024 x 768 pixels 800 x 600 pixels 1024 x 768 pixels Represented colours max 16 2 million max 16 2 million 1024 x 768 pixels max 16 2 million max 16 2 million colours Touch PCAP multi touch Automatic or manual brightness adjustment of the display Processor Intel Atom N2600 Intel Atom 1 75 GHz Dual Core 1 6 GHz Dual Core RAM 4 GB DDR3 Mass storage mS
22. n accordance with 13 of the German Battery Act BattG Batteries may not be disposed of with household waste but must rather be disposed of separately Used batteries must be returned to the point of sale or a disposal system Labelling of electrical and electronic devices in accordance ST with 7 of the German Electrical and Electronic Equipment Act ElektroG Electrical and electronic gn devices must not be disposed of with household waste but must rather be taken to a collection point for waste electrical equipment Such a collection point is generally operated by public waste management authorities i e by municipalities D Symbol for the protective earth connection 2 5 Data figures and modifications All data text and figures were prepared to the best of our knowledge They do not represent any assurance for the properties themselves Despite taking utmost care no liability can be assumed for accuracy completeness and actuality of the information Subject to changes 2 6 Trademarks It is noted that any software and or hardware trademarks and any company brand names mentioned in this documentation are all subject to the general trademark protection rights StoraXe and Big LinX are registered trademarks of ads tec All other third party trademarks used are hereby acknowledged In the case of infringement of trademark rights ads tec reserves the right to exercise all rights 2 7 Copyright This instruction manu
23. n the user interface 8 4 2 LEGIC To test the RFID function select a suitable editor Notepad Word and hold the RFID tag up to the RFID reader The corresponding information is output Recommendation for use The data that are output can be adjusted in advance in consultation with ads tec to meet customer requirements ads tec GmbH Heinrich Hertz Str 1 72622 N rtingen ete itec VMT8000 series 38 9 Drives The storage medium is selected according to the customer requirements The following options are available for storage mSATA Flash A flash with a storage capacity of at least 1GB is used Its capacity depends on the desired operating system and the additional programs to be installed Hard disk SSD A 2 5 hard disk with at least 80 GB SATA capacity is used The device can alternatively be equipped with an SSD Its capacity depends on the desired operating system and the additional programs to be installed External drives The device includes no drive for removable media CD floppy Instead the system provides a USB interface to which an external drive can be connected In this case you d have to ensure that the used device is suitable for industrial environments Connecting or disconnecting external drives during operation is not admissible since it cannot be excluded that the drive might be in use while connecting or disconnecting it Data loss might result in the event of non compliance
24. nsitive components All installation and service work performed on the device must be performed only under safe secure and de energised conditions ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 25 Recommendation for use The shielding of a data cable must always be connected with the connector housing EMC 6 3 Order of steps during commissioning Removing the lid from the service slot Loosen the undetachable screws on the service slot cover by using a Torx Tx10 screw driver and subsequently remove the service slot cover from the device Fig 5 Connecting the cables Please connect all required cables Always use the grommets to correctly install the cables Breaching of IP protection The device can be damaged if the service slot cover is not attached or is attached incorrectly Make sure that the service slot cover is attached correctly before starting operation Recommendation for use Before attaching the service slot cover make sure that the seal is clean undamaged and dry 6 4 Operation The device should be operated by trained and instructed personnel only The manufacturer must be contacted if damage is found 6 5 Taking out of operation The device can be shut down using the ON OFF pushbutton the ignition function and using the software The method to be used depends on the application case ads tec GmbH Heinrich Hertz Str 1 e 72622
25. ons of this instruction manual are translations of the German instruction manual 1 2 Limitation of liability ads tec GmbH shall not be liable for personal injury property damage or damage caused to the device as well as consequential damage that is was the result of non compliance with this instruction manual improper use of the device repairs and other actions on the device by unqualified electricians and electricians not certified by ads tec or that is was the result of using unapproved replacement parts Failure to observe the maintenance intervals shall also result in exclusion from liability Furthermore it is strictly forbidden to make any unauthorised alterations or technical modifications to the device 1 3 Manufacturer The manufacturer of the product is ads tec GmbH The company is referred to in the following as ads tec 1 4 Relevant device documentation The following documents are decisive to device setup and operation Instruction manual this documentation Contains information for installation commissioning and operation of the device along with technical data of the device hardware Website You can download drivers software user manuals leaflets and flyers about the product from our website www ads tec de Recommendation for use We would recommend to make use of our website contents www ads tec de in order to use current data and to be quickly and comprehensively informed of any technical modificat
26. rk performed on the device must be performed only under safe secure and de energised conditions Recommendation for use Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharges The provisions of DIN EN 61340 5 1 DIN EN 61340 5 2 apply ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 4 Product description 4 1 Device features Terminal 2 Front view No Description 1 Display with touch function 2 Front buttons 3 Front USB 4 Power ON button ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen 11 VMT8000 series 12 Rear view No Description 6 Service slot 7 Mounting bracket optional 8 Cover for third WLAN antenna 9 Mounting points for device attachment Information Detailed information on the device can be found in chapter Technical details ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen acis tec VMT8000 series 13 4 2 24 V 48 V DC power supply The device is available with a 24V DC and a 48V DC power supply The power supply is fed in via a 4 pin plug The figure shows the socket inside the device PIN number Signal name 1234 1 PE EL El 2 OV DC Obbo 3 IGN 4 24V 48V DC Recommendation for use The power supply must be protected with a 4A fuse slow blow Hazard due to overvoltage If the protective earth is not attached t
27. s activated or deactivated Intervention by the user is not necessary ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 18 5 Assembly The device series supports various mounting options Further information can be found on our website www ads tec de Hazard due to excessive tightening torque The device can be damaged if the tightening torque is not observed when the bracket is screwed on Tighten the VESA bracket to max 5 Nm ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen ac tec VMT8000 series No Description 1 Bracket for Rittal housing connector top 2 VESA 75 Standard bracket 3 Table vehicle bracket 4 Mounting bracket left right 5 Bracket for Rittal housing connector bottom ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen 19 VMT8000 series 20 5 1 External device dimensions VMT8008 299 189 Fig 1 ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 21 5 2 External device dimensions VMT8010 r re GD 8 60 Fig 2 ads tec GmbH Heinrich Hertz Str 1 72622 N rtingen e tec VMT8000 series 5 3 External device dimensions VMT8012 Fig 3 ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen 22 VMT8000 series 5 4 External device dimensions VMT8015 234 Fig 4 ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen 23
28. sumption do not take into consideration any peripherals connected to the Universal Serial Bus USB interfaces The UL marking applies for operating temperatures up to max 40 C 24V DC power supply and for devices without heater ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 42 13 Service amp support ads tec and its partner companies offer you comprehensive maintenance and support services ensuring quick and competent support should you have any questions or concerns with regard to ads tec products and equipment Because ads tec products are also used by partner companies these devices may have customised configurations Should any questions arise with regard to these specific configurations and software installations please contact them as ads tec will not be able to answer such questions ads tec does not provide support services for any device that was not purchased directly from ads tec In this case maintenance and support is provided by the partner company 13 1 ads tec support The ads tec support team is available for inquiries from direct customers between 8 30am and 5 00pm Monday to Friday The support team can be reached via phone fax or e mail Phone 49 7022 2522 202 Fax 49 7022 2522 2602 Email support ads tec de Alternatively you can contact us by completing a support form on our website www ads tec de Our Support team will then get in touch with you as soon as
29. system volume is additionally displayed by a bar graph If the Fn button is touched the backlighting of the buttons changes from white to blue Level 2 is now active and the required volume can be set Ty Button combination increase volume Button combination reduce volume ads tec GmbH e Heinrich Hertz Str 1 e 72622 N rtingen e itec VMT8000 series 33 As an option the device can be equipped with a Mini PCI Express WLAN card Two integrated antennas are behind the front panel There is a third internally installed antenna on the rear side of the device 8 Wireless 8 1 WLAN optional WLAN antenna emission at front and rear The Mini PCI Express WLAN card supports standards 802 11a b g n Additionally the following security standards are supported WEP 64 bit 128 bit 802 11i WPA TKIP CCMP AES WPA2 TKIP CCMP AES WPA PSK preshared key WPA enterprise EAP TLS The specifications of this network topology must be observed ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 34 Recommendation for use The device can optionally be equipped with an external antenna Make certain that this antenna is connected in order to retain the expanded antenna concept This antenna is connected in the service slot by means of an R SMA plug This function is optional and must be installed at the factory Hazard due to violation of transmit frequencies Due to
30. the use of non approved antennas If an external antenna is used which is not approved by ads tec the operator operating company shall be responsible for compliance with the regulatory and legal requirements 8 2 Bluetooth optional As an option the device can be equipped with a Bluetooth wireless module at the factory Terminals JEMEN The following Bluetooth standards are available Option Name Range Option 1 Bluetooth 2 0 Approx 100m Class 1 Option 2 Bluetooth 2 0 Approx 10 Class 2 50m ads tec GmbH Heinrich Hertz Str 1 72622 N rtingen ete tec VMT8000 series 35 8 3 RFID reader as an option By using the RFID reader passive RFID TAGS RFID chip key card are available for automatic system login The user applies the RFID tag like a key and requires neither user name nor password For authentication the transponder is raised to the position indicated in the image The information on your transponder is read by the device and evaluated by a software solution The MIFARE and LEGIC technology are used in the VMT series Terminals Terminals Position of RFID reader ads tec GmbH e Heinrich Hertz Str 1 e 72622 N rtingen Ye tec VMT8000 series 36 8 4 RFID configuration On delivery the devices are preconfigured so that a test of the RFID functionality can be performed without configuration Recommendation for use Check the functionality of your RFID reader using the followin
31. tions are pre set ex works 7 2 Soft keyboard If an operating system is installed ex works the soft keyboard is also preinstalled If the operating system is delivered separately with the device the soft keyboard must also be installed on site By using the soft keyboard data can be entered via the touch screen like with an external keyboard LELIE E ESE STIILE r LELLE JILIIN I Os E Graphical representation of soft keyboard ads tec GmbH Heinrich Hertz Str 1 72622 N rtingen Ye itec VMT8000 series 30 Operating the soft keyboard Activate and deactivate the soft keyboard for character input using the touch screen Switches numeric keys on and off only if numeric keys are visible Switching between different representations Alphanumeric keys gt Numeric keys gt Position keys View of numeric keys View of position keys Ce Soft keyboard representation zoom in A e Oa Soft keyboard representation zoom out Recommendation for use If functions are to be called for which two keys must be pressed simultaneously on a standard keyboard e g Alt F4 these keys are to be pressed in sequence on the soft keyboard The Shift Alt and Ctrl special keys must always be pressed first Due to differences in programming of a large variety of software programs we cannot ensure that the soft keyboard works properly with all available software When deactivating the soft keyboard the previously
32. ummer Signal Name 1 Di 1 8 2 D1 h BD A D 5 D3 6 D2 7 D4 8 D4 The device contains the Network Controller Intel 1211 GbE Ethernet Controller Information PXE booting is only possible by using the LAN1 port ads tec GmbH Heinrich Hertz Str 1 e 72622 N rtingen e tec VMT8000 series 17 4 6 Serial interface COM1 The serial interface is used for digital data transmission The RS232 interface can be connected by using a shielded 9 pin SUB D cable Information Pin 9 of the serial interface connector can be used for additional connection of a 5V power supply e g for operating a serial barcode scanner The COM 5V switch in the service slot of the device must be put in the ON position in order to use this function A subsequent restart of the computer is required in order to properly activate this function Interface IRQ Address COM1 4 3F8h PIN number Signal name DCD RxD 2 Loen TxD gt DTR GND DSR RTS CTS Rl or 5V DC max 1 OI NJ OO FR oO PM Information This interface is not electrically isolated 4 7 Heater optional As an option the device can be equipped with a heater The heater can be used in for example the low temperature range down to 30 C The exact temperature ranges are specified in the data sheet The heater is controlled automatically by the firmware If the temperature falls or rises to a predefined value the heater i
Download Pdf Manuals
Related Search