Home

User Manual - ads-tec

image

Contents

1. rich Hertz Str 1 e D 72622 N rtingen ads tec GmbH Hein Industrial PCs MCR5000 13 3 2 ORDER OF INSTALLATION The following must be checked before starting the installation e Check the bearing capacity of the wall e Monitor is permitted for fixing with M6 screws by VESA 100 200 e Monitor weight lt 50kg e Monitor size lt 50 e Installation incline lt 30 from vertical line 0 with DVD operation e Observe the monitor data sheet Note The maximum torque for fixing the MCR 5000 installation screws is 5 Nm for wall mount installation Tighten screws evenly O ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 14 PREPARATION FOR FIXING Warning The MCR 5000 device is designated for installation with a TFT or plasma display Before the MCR 5000 can be fixed to the display the respective brackets or retainers for protecting the MCR 5000 from falling must be in place The fall protection measures must correspond to the BGV C1 regulations Respective retainers must be installed above the MCR 5000 device As soon as the retainers have been installed the device should be secured with these brackets or retainers as it can be seen in the figure for example O ads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen ET Eiter Industrial PCs MCR5000 15 ATTACHING THE MCR 5000 IN THE PLACE OF INSTALLATION The MCR 5000 device
2. the brackets or retainers must be hinged back into place in the provided eyes on the monitor Warning You finally have to check that the monitor is properly installed this can be done by visual inspection and by carefully trying to pull the monitor to the front at the bottom edge puna 5J HR A Cas N ASA D ES Q OS r a A lV nn N mm uy d Mag WR n TT HW 1 e A The locking plate is pushed into the provided holes by using both tabs as shown in the figure and finally pushed into the device until the lock snaps audibly and noticeably into place ns ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen Industrial PCs MCR5000 23 4 COMMISSIONING All supply leads and all required data leads have to be connected before commissioning Warning The device must be switched off before connecting or disconnecting any cables in order to prevent damage to the electronics Warning This device may only be switched on after the required ambient temperature is reached in order to avoid condensate accumulation Make sure to meet the permissible voltage requirements for this device Warning After switching off and before switching on you must wait for at least 10 seconds Note The screen of a data cable must always be connected with the connector housing EMC Note Under the embedded op
3. Note This device meets the test requirements for granting the CE sign and according to the European test standards EN 61000 6 3 2001 A11 2004 and EN 61000 6 2 2005 This device complies with the test requirements in accordance with DIN EN 60950 1 2001 VDE0805 IEC950 Safety of Information Technology Equipment The device meets the DIN EN 60068 2 6 test requirements sinus excitation The device meets the DIN EN 60068 2 27 test requirements shock resistance test A respective conformity declaration for the authority in charge is available on request from the manufacturer All connected components as well as cable connections must also meet these requirements for compliance with the EMC legislation For this reason screened bus and LAN cables including screened connectors must be used and installed according to the instructions in this user manual ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen ET tec Industrial PCs MCR5000 9 1 8 SCOPE OF DELIVERY Please check that all of the following components are contained in the packaging e 1x MCR 5000 e 1x Installation bracket pre installed e 1x Locking plate pre installed e 1x Set of keys for locking plate lock Schl sselsatz ji N bech schlie MCR 5000 Montageblech Q The optional cable set might include the following individual cables 1 x Rubber power lead 1 x Rubber power lead extension for monitor display 1x DVI cab
4. The installation procedure described below must be carried out by at least 3 persons due to the weight of the equipment Fix the monitor to the MCR 5000 device by using the pre installed installation bracket Lr Tre ER 7 LE 7 7 EFi d SE EE EFT LLE HZ Z i 737 2 227200 L CA 7271777 NAE 233737377 i ZZ TET Z de EOS Er E hes ES 227777 gt 77 Seis i Z HERE 7 L d Fi EL d PEEL DS ELLIS sis HS d 277 fit LEPER ETE 77 ZZ 277 d d 277777770 SA 277 7277 EE BLES 77 77 Note The figure shows the installation bracket from the point of view of the monitor Please take care that the monitor plate is properly pushed into the guides provided on the MCR 5000 case when attaching the monitor installation bracket is flush with the MCR 5000 unit after installation ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen 20 Industrial PCs MCR5000 ET tec ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen Industrial PCs MCR5000 21 SECURING MONITOR AND MCR 5000 The installation bracket is screwed to the MCR 5000 case by using the previously removed fixing screws M6x10mm Warning The monitor must still be supported by two persons until both components are safely connected Va MIHIR T e an g In H E W ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 22 Subsequently
5. disk with at least 60 GB UDMA is used On delivery the hard disk is formatted in NTFS format default for Windows XP Warning Never remove or insert a hard disk during operation when the device is powered 6 2 DVD DRIVE INTEGRATED MODEL NOTEBOOK The DVD drive is located beneath the locking plate The device must be switched on for opening the drive After pushing the Eject button the drawer jumps open and must be pulled out completely The CD DVD is now placed with the opening on top of the centre piece and carefully pushed downwards until the disk holder snaps in Subsequently the drive must be pushed in Note The DVD drive is of the slim line drive type Warning If the device includes a DVD drive this drive may only be operated perpendicular to the installation position O ads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen ET Eiter Industrial PCs MCR5000 33 6 3 EXTERNAL DRIVES One drive for removable media is integrated in the device by default Additionally the system provides USB interfaces to which an external drive could be connected Warning Removing an external drive during the reading writing process is not permitted Data loss or damage could be the result if this is not observed ads tec GmbH Heinrich Hertz Str 1 e D 72622 N rtingen Ye tec Industrial PCs MCR5000 34 7 TECHNICAL DETAILS 7 1 COMPUTER DATA Processor RAM Graphic controller Graphic memory Ma
6. is installed including the pre installed bracket at the place of installation by using 6 x M6 screws and must be held in place by an additional person during installation N N ET TE ee a 7 N E N YD y Attention a thread depth of at least 12 and at most 15 mm inside the MCR 5000 device must be observed Use all six screwing points EXAMPLE FOR INSTALLING THE MCR 5000 TO A WOODEN WALL FROM 18 MM PLYWOOD Required installation materials not included in the scope of delivery 6 units of M6 x 35 Allen screw acc to DIN 912 6 units of M6 washer for wooden constructions acc to DIN 440R Note The screw length for each individual place of installation is determined in the following way Wall thickness 18mm washer thickness 2 mm required penetration depth 12 15mm screw length 35 mm The 6 screws together with their washers will directly beneath the screw head be put through holes drilled in the wall screwed into the blind rivet nuts in the MCR 5000 device and subsequenily tightened with a torque of 5 Nm ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen ET tec Industrial PCs MCR5000 16 REMOVING THE LOCKING PLATE The locking plate on the device must be removed in order to continue with the installation This is done by opening the lock and by removing the locking plate upwards REMOVING THE INSTALLATION BRACKET For removing the installation bracket it is required to unhi
7. DIO POWER FUSE PIN NUMBER SIGNAL NAME VDC D D GND A U N gt Note The USB interfaces may be locked using the Lock USB software tool You ll find the software and the documentation on the service CD ToP USB INTERFACE One USB interface can be accessed from the front The interface is located under a plastic cover The cover has a tab on the right which is used for protecting the USB connection Note All USB interfaces available meet the USB 2 0 standard 5 3 SIM CARD READER ACCORDING TO ISO 7816 The SIM card reader is currently under preparation for future use ads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 27 5 4 IEEE1394 FIREWIRE 4 PIN CONNECTION WITHOUT POWER The FireWire interface is used for fast data exchange between peripherals e g in industrial and automotive electronics e II en L R SYS USB 1394 LAN DVI I S P DIF AUDIO POWER FUSE PIN NUMBER SIGNAL NAME 1234 4 TPB 2 TPB r 3 TPA 4 TPA Note The FireWire interface complies with the IEEE 1394a standard FireWire 400 5 5 NETWORK CONNECTION RJ45 If the drivers required for functioning are installed on the device the control system may be integrated in an Ethernet network supporting the 10 100 1000 Mbit standard by using the Ethernet 10 100BaseT network connector Specifications of this network topology must be observed in this case You can install t
8. MCR5000 37 9 BATTERY REPLACEMENT Please follow this procedure for replacing the lithium battery inside the device Disconnect all cables between the MCR 5000 and its TFT or plasma display Warning Make sure the power plug has been disconnected before starting disassembly OPENING THE LOCKING PLATE Open the locking plate by using the supplied set of keys After that the locking plate can completely be unhinged and removed 1 Remove both safety screws connecting the installation adapter with the device 2 Push and slide the installation adapter upwards and out of the guide Warning If a TFT or plasma display has been installed disassembly should be carried out by at least two persons Also make sure that the TFT or plasma display is sufficiently supported in order to avoid falling after loosening ads tec GmbH Heinrich Hertz Str Le D 72622 N rtingen Ye tec Industrial PCs MCR5000 38 3 Remove the installation adapter from the MCR 5000 device BATTERY COMPARTMENT LOCATION The location of the battery compartment is highlighted in the figure ry a OPENING THE BATTERY COMPARTMENT 1 Remove the safety screw from the battery compartment lid by using a suitable screw driver ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen ET tec Industrial PCs MCR5000 39 REMOVING THE RETAINING CLIP 2 The battery is kept in place with a plugged in retaining clip The retaining clip can be rem
9. Version e H z A BEL Hu O gt N STA SS x I LL I User Manual Industrial PCs MCR5000 the rugged world of IT Industrial PCs MCR5000 2 Product Portfolio Tablet PCs IT infrastructure Copyright ads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen Germany ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen Pha tec Industrial PCs MCR5000 3 INDEX About us PER k GREEN k k k k OO JO Q ON 3 1 3 2 SE 5 Ku 6 Relevant device documentation ur2au200022an000nannu0nnnnnnunnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 6 Description of the warning symbols used in this guide uuususnnnannonnnnnnnnnnnnnnnnnnnnnnnnnnnnn 6 Data Images Amendments and Variations uuusuoanu0naanunnnnnunnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnenn 6 A PP EEE H Teurdalet 7 o Lalo y E 7 Stellt OCH Til De E 8 MO AEN AE SS nas 8 o e Ro NEO A 9 Operating UV dote EE 10 Opera ino loca lO E 10 Damages due to Improper Use ee ein 10 UU Ty zT TER AAA one eo 11 Treatment and disposal of lithium batteries u2a20000022an0000nnnnnnnnnonnnnnnnnnnnnnnnnnnnnnn 11 SCENE 11 AS SCMDIV ss ia 12 Overall Device Dimensions za222222022aan0000nnannnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnen 12 Order of installation EE 13 COMMISSIONING rennen ita ee 23 Available interfaces ce es sure ea ana sce ee ca ee a n
10. a display Warning Make sure the power plug has been disconnected before starting disassembly LOCATION OF THE FUSE The MCR 5000 fuse is located in the position highlighted in the picture REMOVING THE FUSE In order to remove the fuse inside the MCR 5000 device please push a suitable tool e g a screw driver into the red marked area in order to release the lock as shown in the figure REPLACING THE FUSE You can now remove the fuse from the fuse retainer and replace it with the same type of fuse The type of fuse to be used is Vendor Littelfuse ads tec GmbH Heinrich Hertz Str Le D 72622 N rtingen ET tec Industrial PCs MCR5000 42 Part number 215 010 P INSTALLATION Use the reverse order of steps in this description for re installing the fuse Push the fuse into the retainer and push both components together back into the unit Activate the locking mechanism by using a suitable tool screw driver and slightly pushing the fuse retainer in while twisting it into its initial position Make sure to check that the fuse retainer is properly positioned ads tec GmbH Heinrich Hertz Str Le D 72622 N rtingen Ye tec
11. can be delivered by the manufacturer on request ads tec GmbH Heinrich Hertz Str 1 e D 72622 N rtingen Industrial PCs MCR5000 36 8 SERVICE AND SUPPORT ads tec and appointed partner companies offer you comprehensive maintenance and support services ensuring quick and competent support should you have any questions or concerns with regard to ads tec products and equipment ads tec products may also be provided and installed by partner companies Such devices may have customised configurations Should any questions arise with regard to such specific settings and software installations please contact the system supplier in question as ads tec will not be able to reply to such questions ads tec does not provide support services for any device or unit that was not bought directly from ads tec In any such case maintenance and support is provided solely by the partner company that supplied the device or unit 8 1 ADS TEC SUPPORT The ads tec support team is available for direct clients from Monday to Friday from 08 30 AM to 05 00 PM using the following phone number Phone 49 0 7022 2522 202 Fax 49 0 7022 2522 2602 Email support ads tec de 8 2 COMPANY ADDRESS ads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen Germany Phone 49 0 7022 2522 0 Fax 49 0 7022 2522 400 E Mail mailbox ads tec de Home www ads tec de ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen ET tec Industrial PCs
12. d or hazards or to any hardware and software damages Note This Symbol indicates special notes terms and or conditions that strictly need to be observed to ensure optimised and or zero defect operations It also precedes tips and suggestions for efficient unit implementation and software optimisation 1 3 DATA IMAGES AMENDMENTS AND VARIATIONS The texts data and images herein are not binding The right to any subsequent amendment and or variation due to any technical and engineering progresses in the art whatsoever is hereby reserved ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen ET tec Industrial PCs MCR5000 Z 1 4 TRADEMARKS It is hereby notified that any software and or hardware trademarks further to any company brand names as mentioned in this User s Guide are all strictly subject to the various trademark brand name and patent protection rights WINDOWS WINDOWS CE and WINDOWS CE net are registered trademarks of Microsoft Corp Citrix and ICA are registered trademarks of Citrix Systems Inc Intel and Pentium are registered trademarks of Intel Corp IBM PS 2 and VGA are registered trademarks of IBM Corp CompactFlash and CF are registered trademarks of SanDisk Corp Any further additional trademarks and or brand names herein be they domestic or international are hereby duly acknowledged 1 5 COPYRIGHT This User s Guide inclusive of all the images it contains is entirely p
13. enna nnmnnn nnmnnn ennenen 23 ll ECHTEN an DEEN 24 Readiness for Operation Checks ae 24 Status diISpla SS era o apo iii 24 Iw 25 230 V AC ie Ts e E 25 A vo seg a 26 Sim Card Reader according to ISO 7816 u22 22020000nnnnnn00onnnnnnnnnnnnnnnnnnnonnnnnnnnnnnnn nun 26 IEEE1394 Firewire 4 pin connection without power uuunuuuunnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 27 Network CONMECHION RJ45 scciaicia eiii 27 COM RS232 Serial Interface aria en ana Sa ana ann anna 28 Optional radio network Card EE 28 BAR 29 AUDIO C eee te eee eee 30 ads tec GmbH Heinrich Hertz Str 1 e D 72622 N rtingen Ye tec Industrial PCs MCR5000 4 6 1 6 3 7 1 7 2 8 1 8 2 10 DAVOS iii 32 Hard drives compact flash drive IDE interface cccccesseeceeseecenseseensesenneesenseesonees 32 DVD drive integrated model Notebook ooccconcnccconccccccncccccononnccconcnnnnonannnnennnnnnnnnannnnnananos 32 External TN 33 ee e alle sii ee 34 COMpuler 1 E 34 General data ME 35 Service and SUPPO EE 36 ads tee SUDDO aiii 36 COMP aN VAG a S seen en ee 36 STIT UA e Eaa 37 Fuse FODIAG COON EE 41 ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen ET tec Industrial PCs MCR5000 5 ABOUT US Oads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen Germany Phone 49 0 7022 2522 0 Fax 49 0 7022 2522 400 E Mail mailbox ads tec de Home www ads tec com ads tec GmbH provid
14. erating system interfaces must explicitly be enabled and required drivers must be installed for being able to use them 4 1 AVAILABLE INTERFACES L R SYS USB 1394 LAN DVI I S P DIF AUDIO COM1 O ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen ET Eiter Industrial PCs MCR5000 24 4 2 CABLE INSTALLATION 1 Install all required cables and leads Make sure that the cables are secured against slipping off 2 Connect the MCR 5000 device with a power source by using the AC in socket If you d like to supply a monitor or any other component with power as well you could do this by connecting the component to the AC out socket at the MCR 5000 3 Verify that all cables and leads are correctly installed 4 The power supply is enabled by pushing the Power button 1 Subsequently turn the device on by using the ATX button 2 ER 7a Tr 5 un LU kal R n e E ah e CN P l gt de e m 900 BW fe D gt L z YS USB 1394 LAN DVI I S P DIF AUDIO comi AC OUT POWER FUSE 2 I I 1 4 3 READINESS FOR OPERATION CHECKS Accurately check the unit for any hidden damages possibly incurred during improper transport and or handling or wrong operation site and or storage conditions e g smoke emissions or formation by the unit etc If any damages are found the unit must be decommissioned or scrapped Ensure that it is safe from accidental re implementation 4 4 STATUS DISPLAYS SYS LED BICOLOURED Dependin
15. es large enterprises and globally active corporations with cutting edge technology up to date know how and comprehensive services in the area of automation technology data processing technology and systems engineering en AUTOMATION ads tec GmbH implements full automation solutions from planning to commissioning and is specialized in handling and material handling technologies DATENTECHNIK The data systems division develops and produces PC based solutions and offers a broad range of industrial PCs thin clients and embedded systems SYSTEMTECHNIK ads tec is specialized in modifying and optimizing embedded operating systems and develops software tools to complement its hardware platforms ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen a d e tec Industrial PCs MCR5000 6 1 REMARKS 1 1 RELEVANT DEVICE DOCUMENTATION Consult the following documentation for information pertaining to device setup and operation USER MANUAL ON THE SERVICE CD THIS DOCUMENTATION Contains information pertaining to device mounting startup and operation as well as the technical data for the device hardware SERVICE CD Contains drivers user manual and installation instructions for installing drivers calibration and using the touch screen 1 2 DESCRIPTION OF THE WARNING SYMBOLS USED IN THIS GUIDE Warning The Warning symbol precedes warnings on uses or operations that might either lead to personal injury an
16. g on the colour and type of flashing different device states are displayed by the SYS LED The following signals are displayed e LED lights green The device is ready for operation Power ON e LED is off The device is switched off Power OFF ads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen ET Eiter Industrial PCs MCR5000 25 S INTERFACES 5 1 230 V AC POWER SUPPLY The voltage is supplied through a rubber connector The MCR 5000 is equipped with an AC IN socket through which the voltage can be supplied to the device Additionally the MCR 5000 device is equipped with an AC OUT socket which allows supplying external devices If the MCR 5000 is attached to a monitor the monitor can also be supplied through the AC OUT socket of tne MCR 5000 o ill en L R SYS USB 1394 LAN DVI I S PDIF AUDIO Comi POWER FUSE TECHNICAL DATA OF THE POWER ADAPTER e Power consumption Max 72 Watts e Input voltage 90 264 VAC e Mains frequency 47 63Hz e Current consumption 1 85A e Max switch on current 100A 230V AC Warning The load at the switched AC power supply output must not exceed 500W AC out Max 5A 100V max 2 1A 240V ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 26 5 2 USB CONNECTIONS The USB interfaces are used for connecting peripherals with USB connection o J I N dl dE AE N 7 O L R SY5 USB 394 LAN DVI I S P DIF AU
17. gue C5 RGB ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen ET Eiter Industrial PCs MCR5000 30 5 9 AUDIO L R gt e II W OO w am gt L R SYS USB 1394 LAN DVI I S P DIF AUDIO POWER FUSE ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen a d e tec Industrial PCs MCR5000 31 DESCRIPTION The MCR 5000 is equipped with an S PDIF interface Analogue audio signals may be played on other pieces of equipment by using a commercially available cinch cable The Audio L R cinch EAN ADO input jack allows transmitting analogue audio signals to other pieces of equipment The input jacks may be connected with commercially available cinch cables AUDIO INTERFACE e Note The integrated stereo speakers may be enabled or disabled by using the Internal Speaker Control extension module You ll find a detailed documentation for installation of this extension module on the service CD supplied with the equipment ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 32 6 DRIVES 6 1 HARD DRIVES COMPACT FLASH DRIVE IDE INTERFACE The storage medium is selected according to the customer requirements The following options are available for storage Compact Flash memory A compact flash memory is used Its capacity depends on the desired operating system and the additional programmes to be installed Hard disk A 2 5 hard
18. he drivers required for functioning from the enclosed service CD should they not be installed on the device TIS i en 980 9 o L R SYS USB 1394 LAN DVI I S P DIF AUDIO comi AC OUT POWER FUSE PIN NUMBER SIGNAL NAME 1 8 TX TX RX NC NC RX NC NC CON OOF O M O ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 28 5 6 COM RS232 SERIAL INTERFACE SIGNAL NAME 9 e RxD TxD DTR GND DSR RTS CTS RI O ON OO Bb Y bh Special Note The interface is not electrically isolated 5 7 OPTIONAL RADIO NETWORK CARD If a slot with a radio network card and an externally attached antenna is installed in the device and if this card is supported by the corresponding drivers in the operating system this device may be integrated in an Ethernet network supporting 11 Mbit or 54 Mbit 802 11b g compatible connections Specifications of this network topology must be observed in this case Devices from ads tec including wireless LAN are equipped with a Mini PCI WLAN card including Atheros chips If a device is delivered including operating system by ads tec all required device drivers will also be integrated in the system Under the Windows XP Professional and Windows XP Embedded operating systems the original Atheros Client Utility ACU will also be installed which can be used for defining new WLAN networks and WLAN connection settings The mentioned
19. ion are prerequisites for ensuring safe and proper operation of the device Warning Any leads e g power leads interface cables may only be connected if the device is switched off in order to avoid damaging the device 2 1 OPERATING LOCATION The MCR 5000 model is designed for use with a monitor You have to take care that the environmental conditions specified in the Technical data chapter are met Using the device in non specified environments like e g onboard of ships in areas that might contain explosive gases or in extreme heights is prohibited Warning This device may only be switched on after the required ambient temperature is reached in order to avoid condensate accumulation The same applies if the device has previously been exposed to extreme temperature variations To avoid overheating The device must not be exposed to direct radiation by sunlight or any other light or heat source 2 2 DAMAGES DUE TO IMPROPER USE Should the service system have evident signs of damages incurred e g due to wrong operation or storage conditions or due to improper unit use the unit must be decommissioned or scrapped Ensure that it is safe from accidental re implementation ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen ET tec Industrial PCs MCR5000 11 2 3 WARRANTY REPAIRS During the unit warranty period any repairs thereto must strictly be conducted solely by the manufacturer or by service personnel
20. le 1 x Serial null modem cable O ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 10 2 OPERATING INSTRUCTIONS This device contains electrical voltages and extremely sensitive components The manufacturer or a service partner authorised by the manufacturer should be consulted if you plan to make any modifications For this type of work the device must be switched off at the mains and the power lead must be disconnected Suitable measures for avoiding electrostatic discharge towards parts of the components when touching the equipment must be taken If the device is opened by an unauthorised person hazards for the user might arise and any warranty claim will cease GENERAL INSTRUCTIONS e All users must read this manual and have access to it at all times e Installation commissioning and operation may only be carried out by trained and qualified staff e The security instructions and the manual itself must be observed by all persons who work with this device e AL ihe location of use the valid guidelines and regulations for accident prevention must be observed The accident prevention regulations according to the BGV C1 Accident Prevention amp Insurance regulation must be observed in particular e The manual contains the most important instructions on how to use this device in a safe way e Appropriate storage proper transport installation and commissioning as well as careful operat
21. nge the previously attached brackets or retainers In this case the MCR 5000 must be supported by another person The installation plate is unhinged after removing both safety screws from the MCR 5000 D A _ ads tec GmbH Heinrich Hertz Str 1 D 72622 N rtingen ET Eiter Industrial PCs MCR5000 17 INSTALLING THE INSTALLATION BRACKET The installation bracket including 6 x M6 screws must be screwed to the monitor according to the instructions of the monitor manufacturer Horizontal installation Warning All six screws must be used for fixing the installation bracket Warning The permissible thread depth of the fixing screws inside the monitor case has to be checked before installing the bracket on the monitor ads tec GmbH Heinrich Hertz Str 1 s D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 18 Note Vertical installation is possible depending on the purpose of use and the installation conditions at the display For this purpose the monitor has to be installed in a tilted position according to the manufacturer instructions Vertical installation Warning The installation adapter must always be attached in the centre with both installation methods Verify if vertical operation is permitted for your display unit ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen Ye Eiter Industrial PCs MCR5000 19 MONITOR INSTALLATION AT THE MCR 5000 Warning
22. oved from the battery compartment by carefully lifting the external tabs by using a flat bladed tool screw driver REPLACING THE BATTERY 3 Now the lithium battery can be removed It must be replaced by the same battery type only The type of battery to be used is Saft LS 14250 1 2AA 3 6V 1000mAh um dc Please observe the correct polarity when replacing the battery Warning There is a risk of explosion if the battery is replaced with the wrong type or with the wrong polarity Adhere to the valid regulations for environmentally friendly disposal of batteries if the battery has reached the end of its life cycle ASSEMBLY ads tec GmbH Heinrich Hertz Str Le D 72622 N rtingen Ye tec Industrial PCs MCR5000 40 Please reverse the order of steps described before for re assembling the MCR 5000 device Place the retaining clip on top of the newly inserted battery first Subsequently fit the screws to the battery compartment and to the MCR 5000 casing Observe the required security measures when attaching the installation adapter You can find information about the design of the MCR 5000 device incl its TFT or plasma display in more detail in the user manual ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen Ye tec Industrial PCs MCR5000 41 10 FUSE REPLACEMENT Please follow this procedure for replacing the fuse inside the device Disconnect all cables between the MCR 5000 and its TFT or plasm
23. roprietary and subject to copyright Any irregular use of this Guide by third parties infringing copyright terms is thus strictly forbidden Reproduction translation as well as electronic and photographic image storage and or amendment processes are subject to prior written authorisation directly by M s ads tec GmbH Any violation and infringement thereto will be held liable for compensation of all damages ads tec GmbH Heinrich Hertz Str 1 e D 72622 N rtingen Ye tec Industrial PCs MCR5000 8 1 6 ENVIRONMENTAL CONDITIONS The device may be operated under the following conditions Failure to observe these specifications will terminate any warranty for this device Ads tec cannot be held liable for any damages arising due to improper use and handling Temperature for devices including a HDD In operation O 40 C For storage 20 60 C Because of the integrated maximum temperature memory Temperature for devices including a compact flash memory In operation 0 40 C For storage 20 60 C Because of the integrated maximum temperature memory Humidity In operation 10 85 without any condensate For storage 10 85 without any condensate Vibrations In operation 1G 10 150 Hz DIN EN 60068 2 6 Shock resistance In operation 15 G with a half wave of 11 ms duration DIN EN 60068 2 27 1 7 STANDARDS This device complies with the requirements and protective aims of the following EC regulations
24. ss storage device Interfaces Video Audio Removable disk drives Network Wireless Power supply ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen Pentium M 1 8GHz Pentium M 1 6GHz Pentium M 1 1 GHz Celeron 800 MHz ULV 512 MB to 2GB DDR RAM Intel 855 GME A max of 64 MB shared memory Up to 1600 x 1200 pixels resolution 2 5 hard disk with at least 60 GB UDMA Compact flash memory slot master external access 1 x RS232 SUB D 9 pin 2 x USB 2 0 1 x Firewire 1 x USB 2 0 incl rubber cap on the service side DVI I connection Stereo L R cinch sockets S PDIF Out coaxial cinch socket sound output via four internal speakers As an option Integrated slim line DVD drive 1 x Ethernet 10 100 1000 Mbit RJ45 As an option WLAN card incl 2 integrated antennas 100V 240V AC via rubber connector and power supply circuit breaker AC OUT inc shared fuse max value of 500W ON OFF SUSPEND ACPI pushbutton Industrial PCs MCR5000 7 2 GENERAL DATA External dimensions Weight Environmental temperature Protection class Shock resistance In operation Vibrations In operation EMC EL 404 mm x 325 mm x 56 2 mm W x H x D incl the VESA retainer unit Approx 4 7 kg 5 40 C IP20 15 G with a half wave of 11 ms duration DIN EN 60068 2 27 1G 10 150 Hz DIN EN 60068 2 6 EN 61000 6 3 2001 A11 2004 EN61000 6 2 2005 A corresponding CE conformity declaration
25. that has been duly authorised by the manufacturer 2 4 TREATMENT AND DISPOSAL OF LITHIUM BATTERIES Warning There is an acute risk of explosion should the wrong type of battery be used Do not put lithium batteries into fire do not solder on the cell body do not recharge them open them short circuit them do not reverse their polarity or heat them up over 100 C dispose of them properly and protect lithium batteries from direct sun light humidity and condensation Lithium batteries may only be replaced by the same type or by a type recommended by the manufacturer The lithium battery must be disposed of according to the local legislation at the end of its life cycle Note You ll find a detailed instruction on how to replace the lithium battery in the chapter Battery replacement 2 5 SAFETY INSTRUCTIONS Warning All unit assembly operations must be strictly conducted only under safe secure and zero potential conditions Special Note When handling parts and components susceptible to electrical discharge please accurately observe all the relevant safety provisions DIN EN 61340 5 1 DIN EN 61340 5 2 refers ads tec GmbH Heinrich Hertz Str 1 e D 72622 N rtingen Ye tec d Industrial PCs MCR5000 3 ASSEMBLY 3 1 OVERALL DEVICE DIMENSIONS l e u O
26. utility offers a large variety of settings which in most cases will be sufficient for meeting individual network requirements However there is still an opportunity lacking for making the following settings e Setting the region e g Germany France USA etc e An ad hoc channel setting to be specified by region Note Please refer to the service CD for a more detailed instruction on how to configure the WLAN ads tec GmbH e Heinrich Hertz Str 1 e D 72622 N rtingen ET tec Industrial PCs MCR5000 29 5 8 DVI INTERFACE The DVI interface is used for transmitting analogue and digital video signals A standard DVI cable is required for connecting a digital monitor VGA monitors may also be used by means of a DVI VGA adapter L R 5 SYS USB 1394 LAN DVI 1 S PDIF AUDIO COM POWER FUSE Note The interface is a DVI I single link interface Signals are transmitted in an analogue and digital way PIN NUMBER SIGNAL NAME MEAE e e 1 TMDS Data2 elol ele 2 TMDS Data2 3 TMDS Data2 4 Shield 4 N C 5 N C 6 DDC Clock SCL 7 DDC Data SDA 8 Analogue vertical sync 9 TMDS Data 10 TMDS Datal 11 TMDS Data1 3 Shield 12 N C 13 N C 14 5V Power 15 Ground for 5V 16 Hot Plug Detect 17 TMDS Data 18 TMDS Data0 19 TMDS Data0 5 Shield 20 N C 21 N C 22 TMDS Clock Shield 23 TMDS Clock 24 TMDS Clock C1 Analogue Red C2 Analogue Green C3 Analogue Blue C4 Analogue Horizontal Sync Analogue GND Return analo

Download Pdf Manuals

image

Related Search

Related Contents

制度・お知らせ・スポーツ【11ページ】  JVC KD-S6060 CD Player  document intéressant  User Manual ECU-P1706 - download.advantech.com  Port Designs Manhattan II  Yorkville Sound YS1031 Home Theater System User Manual  Inst Sheet OLW14 RevG_0812.pmd  GMS 120 Professional - Ferramenta L`Utensile  Guida alla ricerca guasti Inverter a frequenza  Ver ficha tecnica - Almacenes Benamiel  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.