USER MANUAL - Wagi Elektroniczne
Contents
1. O Y d NOTE All dimensions are in mm WWSRF platforms WWSRF_03_12 12_EN_U 5 POWER SUPPLY AND START UP The instrument is powered through a rechargeable built in 6Vdc battery 6V RECHAGEABLE BATTERY FEATURES Material nickel metal hydride Power 4 5 Ah Output 6V THE BATTERY MUST ONLY BE REPLACED WITH AN ORIGINAL FROM THE MANUFACTURER In order TO RECHARGE the 6V battery insert the plug end of the provided charger into the socket in the lower part of the platform see the section INSTALLATION and the charger in the mains Safety norms must be respected for the connection to the mains voltage including the use of a line which has to be free from noise generated by other electronic equipment Do not connect other equipment to the same socket as the one that the charger is in Do not step on or crush the power supply cable TO TURN ON the instrument press the C key until the indicator turns on then release The display shows XX YY is the installed software version The instrument turns on all the display segments and symbols MAX XXX XXX capacity of the scale bt XXX in which XXX is a number from 0 to 100 which indicates the battery level The indicator has an auto zero at start up function in other words it means that if at start up a weight within 10 of the capacity is detected it will be zeroed if the weight is not within this tolerance with a non approved instrument the display shows the present weight2. TARE FROM KEYBOARD Press TARE for a few seconds the display shows tM and then 000000 Enter the desired value using the following keys ZERO decreases the blinking digit TARE increases the blinking digit MODE selects the digit to be modified blinking the scrolling of the digits takes place from left to right if pressed for an instant it quickly zeros the present value if pressed at length it allows to return to weighing without saving the changes made Confirm with the ENTER PRINT key the value will be subtracted from the weight present on the plate and the relative pilot lights will turn on CANCELLING A TARE One can manually cancel the tare value in different ways unload the scale and press the TARE or ZERO key carry out the tares in subtraction partially unloading the scale and and press TARE to zero the display press C without unloading the scale WWSRF platforms WWSRF_03_12 12_EN_U enter a manual tare equal to 0 NOTE it is possible to automatically cancel the tare value see the following section LOCKED UNLOCKED DISABLED TARE SELECTION Normally when a tare value is entered automatic or manual by unloading the scale plate the display shows the tare value with a negative sign LOCKED TARE For one s convenience it is also possible to choose that the tare value cancels itself automatically each time that the scale is unloaded UNLOCKED TARE or disable the tare functions With the U
3. after a few instants while with an approved instrument ZEro is shown continuously on the display until the weight does not re enter within this tolerance the auto zero function at start up may be disabled in the set up environment only with non approved instrument see SEtuP gt gt ConFiG gt gt PArAM gt gt Auto 0 parameter TECH MAN REF By pressing the ZERO key for an instant while the version is shown in the display the indicator will show the following in this order XX YY in which XX indicates the instrument type YY indicates the metrological software version XX YY ZZ is the installed software version XXXXXX is the name of the installed software bt XXX in which XXX is a number from 0 to 100 which indicates the battery level K X YY in which K identifies the type of keyboard K 0 5 key keyboard X YY is the installed software version After this it shows the programmed capacity and the minimum division hi rES in case of NOT approved instrument or LEGAL in case of approved instrument the g gravity value and finally it executes a countdown self check TO RESTART the instrument keep the C key pressed for 8 seconds long the indicator will turn off then release the key and the indicator will automatically turn on TO TURN OFF the instrument keep the C key pressed until the message appears on the display then release the key WWSRF platforms WWSRF_03_12 12_EN_U 6 FRON
4. an acoustic signal is emitted after this the indicator turns off For the setting follow the procedures below Turn on the scale press the TARE key while the firmware version is displayed the display shows the tyPE menu Press ZERO many times to scroll ahead through the parameters or TARE to scroll backwards until one finds the F ModE parameter Press ENTER PRINT to enter the menu Scroll until one finds the En SAVE parameter and select it Scroll until one finds the AutoFF parameter and select it With the ZERO or TARE keys select the possible options diSAb auto switch off disabled EnAb auto switch off enabled Confirm with ENTER PRINT if EnAb has been selected will be asked to enter the number of minutes after which the indicator should turn off enter a number between 1 and 255 using the MODE key to select the digit to be modified and ZERO TARE to decrease increase it and confirm with ENTER PRINT Press many times the C key until the display shows SAVE Press ENTER PRINT to confirm the changes made or another key for not saving 8 5 LOW BATTERY WARNING The charge level is shown in the weighing phase through the battery symbol Fur Wh battery is charged m battery is partially charged battery is discharged connect the indicator to the mains in order to recharge the battery if supplied or replace it thermore for a few seconds the Low bat m
5. web site www diniargeo com WARRANTY The TWO YEARS warranty period begins on the day the instrument is delivered It includes spare parts and labour repair at no charge if the INSTRUMENT IS RETURNED prepaid to the DEALER S PLACE OF BUSINESS Warranty covers all defects NOT attributable to the Customer such as improper use and NOT caused during transport If on site service is requested or necessary for any reason where the instrument is used the Customer will pay for all of the service technician s costs travel time and expenses plus room and board if any The Customer pays for the transport costs both ways if the instrument is shipped to DEALER or manufacturer for repair The WARRANTY is VOIDED if any of the following occurs repairs or attempted repairs are made by unauthorised personnel connected to equipment installed by others or is incorrectly connected to the power supply or instrument has defects or damage due to carelessness or failure to follow the guidelines in this instruction manual This warranty DOES NOT provide for any compensation for losses or damages incurred by the Customer due to complete or partial failure of instruments even during the warranty period AUTHORIZED SERVICE CENTRE STAMP
6. NLOCKED tare In case of SEMIAUTOMATIC TARE the net weight before unloading the scale may also be 0 In case of MANUAL TARE the net weight before unloading the scale must be greater than 2 divisions and stable To set the type of tare Turn on the indicator press the TARE while the firmware version is displayed the display shows the tyPE menu Press ZERO many times to scroll ahead through the parameters or TARE to scroll backwards until one finds the F ModE parameter Press ENTER PRINT to enter the menu Press ZERO many times to scroll ahead through the parameters or TARE to scroll backwards until one finds the tArE parameter With the ZERO or TARE keys select the possible options LoCK locked tare unLoCK unlocked tare diSAb disabled tare Confirm with ENTER PRINT Press the key many times until the display shows the message SAVE Press ENTER PRINT to confirm the changes made or another key for not saving 8 3 LIMITATION OF THE TARE FUNCTIONS With approved instrument it is possible to limit the tare functions by setting yES in the step SEtuP gt gt d SALE TECH MAN REF The tare operations will have the following specifications SCALE FUNCTIONING CAPACITY SEtuP gt gt d SALE gt gt rEM dSP gt gt no SEtuP gt gt d SALE gt gt rEM dSP gt gt yES no remote display for the visualization of the remote display for the visualiza
7. T PANEL KEYS The front panel of the indicator is designed for quick and simple weighing applications It consists of a display with 6 digits 25 mm in height and a 5 key water proof film keyboard While weighing various multifunction symbols indicating the functioning status will turn on see section SYMBOLS ON THE DISPLAY SCALE KEY FUNCTION Zeros the displayed gross weight if it is within 2 of the total capacity ZERO Cancels the negative tare value When entering numbers it decreases the digit to be modified It allows scrolling ahead inside the menu steps or in the parameters within a step If pressed for an instant it carries out the semiautomatic tare TARE If pressed at length it allows entering the manual tare from keyboard Cancels the negative tare value In the numeric input phase it increases the digit to be modified It allows scrolling backwards the menu steps or in the parameters within a step MODE It carries out a specific function of the operating mode set in the set up environment In the numeric input phase it selects the digit to be modified from left to right It carries out a specific function of the operating mode set in the set up environment In the numeric input phase it confirms the entry made ENTER ERIN In the SET UP it allows to enter a step or to confirm a parameter within a step It transmits the data from the serial port dedicated to the
8. USER MANUAL WWSRF WIRELESS WHEEL WEIGHING PLATFORMS WWSRF_03_12 12_EN_U WWSRF platforms WWSRF_03_12 12_EN_U INDEX 1 INTRODUCTION cias iia 1 2 MAIN TECHNICAL SPECIFICATIONS acia 2 J SYMBOLS ani aaa a a sa 3 4ANSTALLA TON an naa anita 3 4 1 VERSION WISE RE satan estoi ti 4 AO VEROION dd Etc LOS 5 35 POWER SUPPLY ANE START UP canina ata 6 6 FRONT PANEL KEY Socia ara ia 7 Ts SYMBOLS ON THE DISPLAY asnicar coin 8 8 BASIC FUNCTIONS tii 9 8 1 ZERO SCALE netiis ces E e e de e 9 8 2 TARE OPERATIONS a a Nd aa a a er a a i t 9 8 3 LIMITATION OF THE TARE FUNCTIONS sucias 10 9 4 AUTO POWER OFF FUNG TION wide TAEAE a eae 11 8 5 LOW BATTERY WARNING ad 11 8 6 DISPLAY OF METRIC DATA inFO naaa 11 BLOCK UNLOCK KEYBOARD 12 9 INSTRUMENT MESSAGES WHILE IN 12 DECLARATION 13 WARRANTY iaa A AA AA AAA AAA AAA AAA 13 WWSRF platforms WWSRF_03_12 12_EN_U 1 INTRODUCTION These wireless platforms are designed for creating weighing stations for large vehicles and axle weighing and avoid the hassle of connecting cables between the platforms and the indicator The platforms are ideal for weighing larger vehicles vans trucks tankers etc IN WARNING IN Any attempt to repair o
9. city 12 Calibration error the acquired calibration point 1 o tP2 o tP3 is equal to the zero point Er 37 The number of converter points per scale division is less than two Carry out again the calibration with special attention to the capacity and the division 39 It is displayed when the instrument has not yet been calibrated and initialized Press the TARE key when the instrument displays Er 39 to enter the technical set up environment Carry out the initialization of the indicator dEFAu parameter and the selection of the type of keyboard parameter and finally the programming of all the parameters of the set up environment and the calibration undEr The weight in underload i e a weight of 100 divisions below the gross zero if the instrument is approved is blinking notified through this message alternated to and by an acoustic signal oVEr The weight in overload i e a weight of 9 divisions greater than the capacity is notified through this message blinking alternated to and by an acoustic signal r AdCX It confirms that the WWSRF platform corresponding to the X channel is connected to the DFWKRPRF WWSRF platforms WWSRF_03_12 12_EN_U DECLARATION OF CONFORMITY This device conforms to the essential standards and norms relative to the applicable European regulations The Declaration of Conformity is available in the
10. ess the C key to return to weighing TE The minimum weigh corresponds to 20 net weight divisions 11 WWSRF platforms WWSRF_03_12 12_EN U 8 7 LOCK UNLOCK KEYBOARD It is possible to enable disable the keyboard by setting the corresponding parameter in the F ModE gt gt LCk kEy step of the setup environment TECH MAN T if the on parameter is selected in this step after 15 seconds of keyboard inactivity in the weighing phase the keyboard is locked the LoC kEy message is displayed In this case it s only possible to turn off the instrument by pressing the C key for about 10 seconds and turn on the instrument By pressing the ZERO and PRINT keys in succession the keyboard is unlocked the unL kEy message is displayed If a different key is pressed the message PrESS ZEro to unLoCk is displayed when the ZERO key is pressed the message noW PrESS Print to unLoCk is displayed 9 INSTRUMENT MESSAGES WHILE IN USE MESSAGE DESCRIPTION ZEro The scale is zeroing the weight Er Mot Unstable weight during the calibration PrEC It is displayed if one tries to calibrate the zero point without first having confirmed the number of calibration points ErPnt During the acquisition of a calibration point a null value has been read by the converter 11 Calibration error too small sample weight has been used it is advisable to use a weight equal to at least half of the scale capa
11. essage appears on the display minimum level voltage en recharging the battery if supplied the indicator shows the recharging phase below RECHARGING PHASE LP gt I gt MM gt im 5 RECHARGE IS COMPLETED Miir NO In TES a system that consists of a DFWKRPRF connected to the WWSRF platforms the level of the battery of the platforms is displayed on the DFWKRPRF through the message ChX btY in which X is the number of the channel and Y is the number of notches of the battery symbol The message is displayed when there is a variation of a notch in the battery symbol of one platform and this level is maintained for at least three minutes While recharging the instrument can be used as usual The instrument automatically turns off when the voltage goes below the minimum level It s possible to view the recharge percentile of the battery by pressing the ZERO key upon start up see the section POWER SUPPLY AND START UP 8 6 DISPLAY OF METRIC DATA inFO The indicator is fitted with a function named INFO thanks to which it is possible to view the configuration metric data keep the key pressed until the display shows inFo and release or press the keys MODE keys in sequence NO The capacity value will appear Press the ZERO key to scroll the following data in this order Capacity gt Minimum weigh gt Division gt Press the TARE key to scroll backwards the metric data Pr
12. g the metric information it identifies the indicated division range 9 LT The locked tare is enabled 10 PT The manual tare is active 11 W1 The instrument is in the first weighing range 2 Not managed W3 Not managed 12 TETEE Scale nr 1 is always shown 13 PCS Not managed WWSRF platforms WWSRF_03_12 12_EN_U 14 kg Indicates the unit of measure in use kg for kilogram g for gram 15 Not managed 16 t Indicates the unit of measure in use tons 17 LB Indicates the unit of measure in use pounds 18 f Not managed 19 Indicates that a key has been pressed 20 PEAK Not managed 21 HOLD Not managed 22 SP1 Not managed SP2 Not managed SP3 Not managed SP4 Not managed 8 BASIC FUNCTIONS 8 1 ZERO SCALE By pressing the ZERO key it is possible to zero a gross weight value which is within 2 of the capacity after the zeroing the display shows 0 weight and the relative pilot lights are turned on 8 2 TARE OPERATIONS SEMI AUTOMATIC TARE By pressing the TARE key any weight value present on the display is put in tare the display shows tArE for an instant and then 0 net weight the pilot lights turn on NOTE The semiautomatic tare will be acquire only if the weight is AT LEAST A DIVISION STABLE instability led off and VALID in other words the OVERLOAD condition must not be created ENTERING THE MANUAL
13. heeled bin on the product means that at the product end of life it must be taken to separate collection or to the reseller when a new equivalent type of equipment is purchased The adequate differentiated refuse collection in having the product recycled helps to avoid possible negative effects on the environment and health and supports the recycling of the materials of which the equipment is made The unlawful disposal of the product by the user will entail fines foreseen by the current regulations WWSRF platforms WWSRF_03_12 12_EN_U 2 MAIN TECHNICAL SPECIFICATIONS POWER SUPPLY MAXIMUM POWER OPERATING TEMPERATURE DISPLAYED DIVISIONS MAXIMUM INPUT SIGNAL MINIMUM VOLTAGE PER DIVISION RESOLUTION IN CALCULATION KEYBOARD TARE FUNCTION AUTO POWER OFF LOW BATTERY WARNING BATTERY RECHARGE TIME LOAD CELL POWER SUPPLY LOAD CELL CONNECTIONS 6Vdc rechargeable battery 4 5 Ah NOTE recharge the battery using only the charger provided 5 VA From 10 to 40 C 14 to 104 F with even temperature 10000 3X3000e for legal for trade use expandable to 800 000 for internal use with minimum signal coming from the 1 6mV V cell 6 mV V 0 3 uV approved instrument 0 03 uV non approved instrument 1 500 000 points with signal in input equal to 3mV V Water resistant polycarbonate mechanic keys with tactile and acoustic feedback Available on the entire capacity Programmable from 1 to 255 minutes o
14. printer It turns the instrument on and off Cli In the numeric input phase it quickly zeros the present value In the SET UP it allows to exit a step without confirming the change made in the indicator Allows viewing the scale s metric information capacity division minimum weigh for each configured range WWSRF platforms WWSRF_03_12 12_EN U 7 SYMBOLS ON THE DISPLAY The LCD display has symbols which show the indicator s functioning status you will find the description for each symbol below ib bi ABABA Maxu Mins LTPT WiW2W3 227 222223274 Pes i cae DISPLAY NUMBER SYMBOL FUNCTION 1 DIE The weight detected on the weighing system is near zero within the interval of 1 4 1 4 of the division 2 The weight is unstable 3 Ae Not managed 4 NET The displayed weight is a net weight 5 G The displayed value is a gross weight if the Italian or English language is selected in the print configuration 6 B The displayed value is a gross weight if the German French or Spanish language is selected in the print configuration 7 Indicates the battery charge level see the section LOW BATTERY WARNING 8 MAX When viewing the metric information it identifies the indicated capacity range MIN When viewing the metric information it identifies the indicated minimum weigh range e When viewin
15. r alter the unit can expose the user to the danger of electric shock and it will void our warranty This instrument is covered under warranty provided that IT HAS NOT BEEN OPENED BY THE USER for any reason If any problem with the unit or system has been experienced please notify the manufacturer or the dealer from which the instrument was acquired The 6V rechargeable battery has to be completely recharged 12 hours in the first installation of the instrument we RECOMMEND disconnecting the battery if the instrument is not going to be used for more than 30 days In order to avoid the deterioration of the rechargeable battery In standard conditions never leave the battery partially or completely uncharged at least once a week recharge it completely In case the instrument is not used for a long period one needs to completely recharge the battery before the system is switched off for the last time recharge completely every 3 months Do not pour liquids on the indicator Do not use solvents to clean the indicator Do not expose instrument to any heat sources Always mount the platform in a vibration free setting Do not install in an environment with any risk of explosion All the connections of the instrument have to be made respecting the rules applicable in the zone and in the installing environment Everything not expressly described in this manual has to be considered as improper use of the equipment The crossed out w
16. r disinserted Low Batt will appear on the display 12 hours 5Vdc 5 120mA max 8 cells of 350 Ohms 6 wires CELL1 with Remote Sense 4 wires CELL 2 3 4 without Remote Sense THE PARTS OF THE INSTRUMENT CONTAINING DANGEROUS ELECTRICAL TENSION ARE ISOLATED AND INACCESSIBLE TO THE USER UNLESS IT HAS BEEN DAMAGED OPENED OR ALTERED WWSRF platforms WWSRF_03_12 12_EN_U 3 SYMBOLS To call the attention of the user the following symbols are used both in the manual and on the instrument itself A WARNING This operation must be performed only by qualified personal Conforms to the standards of the European Union AID Identifies the Class Of Precision defined by the OIML to represent 3000 divisions 4 INSTALLATION To recharge the battery of the instrument one has to connect the charger provided to the corresponding input in the lower part of the platform In the following two paragraphs the dimensions of the different versions of platforms are shown WWSRF platforms 4 1 VERSION WWSERF WWSRF_03_12 12_EN_U pat 75 0 1 N O O la le EN O O O Y NOTE All dimensions are in WWSRF platforms WWSRF_03_12 12_EN_U 4 2 VERSION WWSDRF 950 E 1 O o
17. tion of the tare tare lt 100kg All the tare functions are disabled The SEMIAUTOMATIC TARE value can not be modified with a manual tare The manual tare can be entered or modified only with an UNLOADED scale and tare equal to zero It s possible to cancel the tare value only with an UNLOADED scale by pressing the ZERO key or by entering a manual tare equal to zero The SEMIAUTOMATIC TARE value can not be The SEMIAUTOMATIC TARE value can not be gt 100kg modified with a manual tare modified with a manual tare The manual tare can be entered or modified only The manual tare can be entered or modified with an UNLOADED scale and tare equal to only with an UNLOADED scale and tare equal zero to zero It s possible to cancel the tare value only with an It s possible to cancel the tare value only with UNLOADED scale by pressing the ZERO key an UNLOADED scale by pressing the ZERO key or by entering a manual tare equal to zero key or by entering a manual tare equal to zero With approved instrument the d SALE and rEM dSP steps are read only WWSRF platforms WWSRF_03_12 12_ 8 4 AUTO POWER OFF FUNCTION It is possible to automatically turn off the indicator from 1 to 255 minutes or disable it the auto power off takes place when with unloaded scale the weight has not been moved or a key has not been pressed for the time set the display shows the oFF blinking message and
Download Pdf Manuals
Related Search