USER'S MANUAL compact handheld 1D/2D code scanner
Contents
1. for example freezing area s or temperatures higher than 40 C please contact your local dealer or Opticon Avoid contact with water B Shock ESD Do not expose the scanner to strong impact do not throw or drop the scanner Do not present mechanical shocks to the product Do not leave product in an area where static charge is accumulated or near devices where electromagnetic emission is generated C Cleaning Clean the reading window regularly to maintain optimum reading performance Clean the exterior of the scanner by wiping it with a soft lightly moist cloth Do not use a high pressure cleaning method If a cleaning liquid is needed only use one drop of a non abrasive household liquid Clean the electrical contacts of the scanner and the cradle with a soft dry cloth or cotton bud Do not use water or sanding paper This can cause malfunction D Maintenance There are no user serviceable parts inside the scanner So do not try to take it apart In case of malfunction please consult your local dealer or Opticon E Recycling amp Disposal instructions X The icon on the product or package indicates that the product should not be thrown in the home waste bin The product must be recycled as an electronic product For proper treatment of end of life products consult the section for Environmental care on www opticon com F Charging instructions Charge the battery by placing the scanner in the cradle Place the scanner in2. its cradle after scanning to maintain the capacity of the battery THE SCANNER IS NOT WARRANTED FOR DAMAGE DEFECTS MALFUNCTION OR LOSS OF DATA RESULTING FROM INCORRECT USE OF THE BATTERY a Qum 05 Ee TA n d Ga 7 i br a es a L i el hi u DA iti Ela i SS smi ini W gt MSI WI e 3 READING CODES Check the scanning engine Is the scanning engine on Is a red light beam visible If not press the trigger key For models without a trigger key check the cable connection Approach the code e Point the reading window of the scanner in the direction of the code e The code should fit from margin to margin in the light beam width e Move the scanner close to the label e Check the data at the connected computer device A Good Read means that the scanner has effectively recognized and decoded the code In most cases the application program will provide an indicator signal or a buzzer signal to indicate a good read to the user When the read is incorrect you can try again paying attention to the instructions below YA TROUBLE SHOOTING General checks e Make sure the scanner is installed properly e Check the power supply of all devices e Is the reading window of the scanner clean e Are the codes on the labels damaged Scanner does not operate e Check the trigger switch e Check if you connected the right interface Code could not be read e Check that the wid
3. ber appearing on your Opticon device has not been removed Removing the serial number might affect the warranty conditions and liability disadvantageously so please be strict at maintaining the label with serial number on the Opticon product Warranty Warranty period Liability Unless otherwise agreed in a contract all Opticon products are warranted for a period of two years after purchase covering defects in material and workmanship Opticon will repair or at its opinion replace products that prove to be defective in material or workmanship under proper use during the warranty period Opticon will not be liable in cases where modifications are made by the customer In such case the standard repair charge will be applicable The standard charge for repair will also be applicable in cases where no defect is found at all These rules also apply for products that are still under warranty Under no circumstance Opticon Sensors Europe B V will be liable for any direct indirect consequential or incidental damages arising out of use or inability to use both the hardware and software even if Opticon has been informed about the possibility of such damages Packaging The packing materials are not harmful for the environment We recommend that you save all packing materials as it should be used whenever you need to transport your scanner eg for service Damage caused by improper repacking is not covered by the warranty Trademar
4. ei ENGLISH compact handheld 1D 2D code scanner eer OP TICON ee OPTICON OPTZCON N INSTALLATION U INSTRUCTIONS LIMITED WARRANTY AND DISCLAIMERS FIRST STEP TURN POWER OFF Exercise caution at all times when working with AC and DC powered equipment e Turn off all your equipment before installation e It is strongly recommended to use Opticon cables and power supplies NEXT STEPS CONNECT INTERFACE e Find your interface type in the corresponding diagram e Connect the scanner to the computer in accordance with the diagram and corresponding Instructions e Turn your computer equipment on When using a battery powered scanner charge the battery before use DIAGRAM AND INSTRUCTIONS See diagram on the left side of this page Connection CABLED 1 RS 232 interface cable connection DB9 DB25 Plug connector into the host If power is required Connect external power supply 2 Keyboard wedge connection Disconnect the keyboard Plug the male side to the host Plug the female side to keyboard If power is required Connect external power supply 3 USB cable Make sure your computer runs Windows 98 or higher Plug USB connector of scanner into the host If power is required Connect external power supply 4 Test read bar code Read the OPTICON bar code and check the result at the host C
5. k Trademarks used are property of their respective owners version 04 2006 1 DETAILED VIEW Depending on the supplied model and or the configured options the following options are applicable 1 Reading window to read the codes Never obstruct this window 2 Trigger key to activate the scanner 3 LED indicator 4 Buzzer Beeper Typical LED indication red no code reading no code acceptation power is on green successful code reading battery full flashing LED data transmission blue Bluetooth connection 802 15 4 communication 5 Cable Connector To connect the scanner or cradle to the computer equipment consult installation instructions 6 Scanner label Connection label A label is fixed to scanner and or cable containing the serial number On a Bluetooth product a connection label with device address might be attached Do not remove it 7 Charging contacts If the scanner is inserted in the cradle the battery will automatically be charged If no scanner is inserted keep the charging compartment empty do not insert paper clips coins or other materials to avoid short circuit 8 Input socket Input for power supply 9 Handstrap Fix for convenient use and to avoid drop YA HANDLING INSTRUCTIONS A Temperature conditions Use in area s between 0 and 40 C Do not expose the scanner for a long time to direct sunlight or near direct heat For use under extreme conditions
6. onnection WIRELESS A Cradle connection USB interface remark Download USB driver from www opticon com and install the driver on the host e Interface connection Connect the interface cable cradle to the cradle and to the host Connect always one type of interface Do not connect for example both USB and RS232 e Power connection Connect the power supply to the cradle and the main socket B Wireless connection between scanner and cradle Scan the label with device address on the bottom of the cradle to connect scanner to cradle C Test read barcode Read the OPTICON bar code and check the result at the host If you have any questions please contact your local dealer or Opticon CAUTION This user s manual may be revised or withdrawn at any time without prior notice Copyright 2006 Opticon Sensors Europe B V All rights reserved This manual may not in whole or in part be copied photocopied reproduced translated or converted to any electronic or machine readable form without prior written consent of Opticon Sensors Europe B V BY OPENING THE PACKAGE OF THIS PRODUCT YOU AGREE TO BECOME BOUND BY THE LIABILITY AND WARRANTY CONDITIONS IN ALL CIRCUMSTANCES THIS MANUAL SHOULD BE READ ATTENTIVELY BEFORE INSTALLING AND OR USING THE PRODUCT Serial number A serial number appears on all Opticon products This official registration number is strictly related to the device purchased Make sure that the serial num
7. th of the code does not exceed the width of the light beam e Change the angle between the code and the scanner e Change the distance between the code and the scanner Communication malfunctioning e Check if the interface cable is undamaged and properly connected to the cradle and the host computer e Check the connection of the power supply e Check if the main socket has power e Check if the connection is configured properly If you can not solve the problem Contact your local dealer or Opticon When the scanner needs to be repaired The label with serial number should be present If returning the scanner please use the original packaging to minimize the chance of damage More information The scanner is configured to default factory settings and is supplied with information that gives you a quick understanding of the product More product details additional support or configuration options to your own preferences by Opticonfigure will be updated at www opticon com The Netherlands Hoofddorp France ISSY Les Moulineaux CEDEX Germany Dietzenbach Italy Castel Maggiore BO Spain Valencia Sweden J rf lla United Kingdom Luton Bedfordshire U S A Orangeburg Japan Warabi City Taiwan Taipei PR China Shanghai Australia Kariong www opticon com OF TiCON
Download Pdf Manuals
Related Search