4 Your VS-211H Automatic HDMI Standby
Contents
1. LCD Display with Speakers DVD Player 1 DVD Player 2 Step 2 Connect the power Step 3 Control via the REMOTE see section 5 Connect the appropriate input FIN IN 1 or IN 2 to the G Ground FIN 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview Overview The VS 211H is a high performance automatic standby switcher for HDMI 1 3 video signals The VS 211H automatically switches to the secondary input whenever the primary video signal is interrupted If the primary signal reappears the unit automatically switches back to the primary input In addition the VS 211H features e A maximum data rate of up to 2 25Gbps e HDTV compatibility e HDCP and HDMI compliance e A DEFAULT INPUT switch for selecting the default HDMI master source signal e Contact closure remote control for forced operation e Active switching To achieve the best performance e Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer VS 211H away from moisture excessive sunlight and dust No operator serviceable parts inside unit Use only the Kramer Electronics input power wall adapter that is provided with this unit anut Disconnect power and unplug unit from2. wall before installing or removing device or servicing unit 1 Available from Kramer Electronics on our Web site at http www kramerelectronics com 2 For example part number 2535 052002 Your VS 211H Automatic HDMI Standby Switcher 4 Your VS 211H Automatic HDMI Standby Switcher Figure 1 and Table 1 define the VS 211H i DEFAULT REMOTE IN1 Ni GIN2 oe BV DC GY SZ 8 ACTIVE INPUT lay CY O O ON A O Automatic HDMI Standby Switcher VvS 211H J Figure 1 VS 211H Automatic HDMI Standby Switcher Table 1 VS 211H Automatic HDMI Standby Switcher Features Feature Function 1 OUT HDMI Connector Connects to the HDMI output acceptor 2 IN 1 HDMI Connector Connects to the HDMI input source 1 3 IN 2 HDMI Connector Connects to the HDMI input source 2 4 DEFAULT INPUT Switch Switches to select the default input IN 1 or IN 2 5 REMOTE IN 1 and IN 2 Terminal Block Connectors Connect to a contact closure switch 6 5V DC 5V DC connector for powering the unit 7 ACTIVE INPUT 1 2 LEDs IIluminates when input is active 8 ON LED Iluminates when receiving power KRAMER SIMPLE CREATIVE TECHNOLOGY Using the VS 211H Automatic HDMI Standby Switcher 5 Using the VS 211H Automatic HDMI Standby Switcher This sect
3. Kramer Electronics Ltd USER MANUAL Model VS 211H Automatic HDMI Standby Switcher Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 4 Your VS 211H Automatic HDMI Standby Switcher 5 Using the VS 211H Automatic HDMI Standby Switcher 5 1 Connecting the VS 211H Automatic HDMI Standby Switcher 5 2 Selecting the Default Master Source Signal 5 3 Connecting the REMOTE Terminal Block Connector 6 Technical Specifications Figures Figure 1 VS 211H Automatic HDMI Standby Switcher Figure 2 VS 211H Automatic HDMI Standby Switcher Connections Figure 3 REMOTE Terminal Block Connector Tables Table 1 VS 211H Automatic HDMI Standby Switcher Features Table 2 Technical Specifications of the Automatic HDMI Standby Switcher O ANDAA A A LU NBE m AK Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Congratulations on purchasing your Kramer DigiTOOLS VS 211H Automatic HDMI Standby Switcher This product is ideal for providing backup switching for broadcast and p
4. ignal is not detected the VS 211H automatically activates the standby input IfIN 1 is the default input and it fails IN 2 activates IfIN 2 is the default input and it fails IN 1 activates If the master input reactivates while the standby input is active the unit automatically switches back to the master input IfIN 2 is active while IN 1 is the default input when IN 1 reactivates it is switched to the output IfIN 1 is active while IN 2 is the default input when IN 2 reactivates it is switched to the output KRAMER SIMPLE CREATIVE TECHNOLOGY Using the VS 211H Automatic HDMI Standby Switcher 5 3 Connecting the REMOTE Terminal Block Connector Regardless of the default input switch setting you can force the switching of the active input by remote control To do this connect the appropriate REMOTE input terminal block connector pins to a contact closure switch see Figure 3 e To force IN 1 connect REMOTE IN1 to PIN G ground e To force IN 2 connect REMOTE IN2 to PIN G ground Do not connect both the REMOTE IN1 and the REMOTE IN2 to PIN G simultaneously 1 Note that the connection should be permanent since the VS 211H reverts to an automatic switcher when the connection is removed Attach PIN IN1 to REMOTE Attach PIN IN2 to REMOTE PIN G to activate IN1 G IN2 PIN G to activate IN1 G IN2 INPUT 1 INPUT 2 Figure 3 REMOTE Terminal Block Connector Note The contact closure setting rema
5. ins in effect until an event occurs such as changing the default input switch or connecting or attaching an HDMI device Technical Specifications 6 Technical Specifications Table 2 includes the technical specifications Table 2 Technical Specifications of the Automatic HDMI Standby Switcher INPUTS 2 HDMI on HDMI connectors OUTPUTS 1 HDMI on an HDMI connector DATA RATE Supports 2 25Gbps per graphic channel STANDARDS COMPLIANCE HDCP and HDMI CONTROLS Contact closure remote control input default selection switch POWER SOURCE 5V DC 510mA DIMENSIONS 12cm x 7 2cm x 2 4cm 4 7 x 2 8 x 1 0 W D H WEIGHT 0 3kg 0 7Ibs ACCESSORIES Power supply mounting bracket OPTIONS RK 3T 19 rack adapter 1 Specifications are subject to change without notice 8 KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGISTHE WARRANTY Labor and parts are warranted for three years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVEREDAND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which
6. ion describes how to e Connect the VS 211H see section 5 1 e Select the default master source signal see section 5 2 e Connect the REMOTE connector see section 5 3 5 1 Connecting the VS 211H Automatic HDMI Standby Switcher To connect the VS 211H as illustrated in the example in Figure 2 do the following 1 Connect HDMI input source 1 for example DVD player 1 to the IN 1 HDMI connector 2 Connect HDMI input source 2 for example DVD player 2 to the IN 2 HDMI connector 3 Connect HDMI acceptor for example an LCD display to the OUT HDMI connector 4 Set the DEFAULT INPUT switch to whichever input is the master input as described in section 5 2 5 Ifneeded connect the remote switches to the REMOTE IN 1 and IN 2 terminal block connectors as described in section 5 3 6 Connect the 5V DC power adapter to the power socket and connect the adapter to the mains electricity 1 Switch OFF the power on each device before connecting it to your VS 211H After powering up your VS 211H switch on the power on each device 5 Using the VS 211H Automatic HDMI Standby Switcher HDMI LCD Display with Speakers DVD Player 1 DVD Player 2 Figure 2 VS 211H Automatic HDMI Standby Switcher Connections 5 2 Selecting the Default Master Source Signal When active input sources are connected to IN 1 and IN 2 the DEFAULT INPUT switch setting determines the default master input source If the master input s
7. is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts ofnature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FORAND WHATWEWILLNOT PAYFOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid
8. ost production applications Note that the Kramer VS 211H is identical to the VS 211HDMI just the name has changed replacing the suffix HDMI by H according to the HDMI Guideline The package includes the following items e VS 211H Automatic HDMI Standby Switcher e Power supply 5V DC e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from our Web site at http www kramerelectronics com 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com l Getting Started 2 1 Quick Start This quick start chart summarizes the basic setup and operation steps Step 1 Connect the inputs and the outputs see section 5 1 Connect the inputs Connect the output to the display SELECT THE DEFAULT INPUT if so Oey N3 T
9. to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OFIMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from
10. your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION B Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment Use the supplied DC power supply to feed power to the machine Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products XX B gt K For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution O Institute of Quality amp Control x Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000681 REV 2
Download Pdf Manuals
Related Search