Home

OPERATORS MANUAL PE 15

1. hot and pin 1 chassis ground When using 1 4 plugs the preferred arrangement is to use a tip ring sleeve version and leave the ring open Alternatively a mono plug may be used Rane Corporation 10802 47th Ave W Mukilteo WA 98275 5098 Manual 4 OPERATING INSTRUCTIONS Once the PE 15 is properly installed it is then time to twist some knobs Power up the system in the normal fashion always turning on the power amplifiers last It is good practice to start at the head of the system turning on any sound sources and mixers first equalization devices next and finally power amplifiers Following this power up sequence minimizes the change of high gain stage turn on transients finding their way to the loudspeakers It is very wise to start with the PE 15 s MASTER CONTROL all the way down and the five LEVEL controls set to their center detents This eliminates the possibility of surprises encountered by having 15 dB of boost centered at a feedback frequency With either a canned or live source applied advance the MASTER CONTROL until normal system gain is achieved Now you are ready to make some adjustments A detailed discussion on room equalization lies outside the scope of this manual however a few words can t hurt Experienced sound people almost always use some sort of realtime analyzer RTA as an aid in setting equalization An RTA allows you to see the frequency response changes as you do them This is invaluable i
2. ANE OPERATORS MANUAL PE 15 PARAMETRIC EQUALIZER QUICK START If all else fails read the manual Yeah yeah But nothing is going to fail and you being one smart cookie don t need to read the stupid manual But you should read this section just to cover your affairs So quickly here goes The PE 15 has few hidden gotchas One of these may be the shelving feature of Bands 1 and 5 Remember that pulling on the bandwidth BW knob causes it to come forward with a positive click indicating the Shelf Mode is active Use Shelving Bands 1 and 5 like Bass and Treble tone controls where you want control over the whole top or bottom ends of the spectrum Hook up is simple The PE 15 accepts all combinations of balanced or unbalanced XLR 14 TRS or TS connectors However note the INPUT connectors are wired in parallel and may not be used together Use only one at a time They will not function as a summing type of Input for two different sources but they may be used in a daisy chain fashion to feed other units On the other hand to randomly pick a hackneyed expression you may use the paralleled OUTPUTs to drive two destinations Never connect anything except a Rane approved AC power supply to the thing that looks like a red telephone jack on the rear of the PE 15 WEAR PARTS This product contains no wear parts Manual 1 FRONT PANEL DESCRIPTION PARAMETRIC QUALIZER POWER switch The key to life in any el
3. alies while the parametric helps source correction loudspeaker compensation and feedback control In these situations the order of placement is not critical however the PE 15 does feature true actively balanced differential outputs which may be a consideration in installations requiring very long cable runs between the equalizers and the power amplifiers or crossovers The 4 TRS and XLR INPUT connectors are wired in parallel and are actively balanced These Inputs are provided primarily to give the user a choice between two types of connectors They will not sum from two different sources For further information on this subject please consult the RaneNote titled WHY NOT WYE available from the factory or the Rane web site The two Inputs may be used in a daisy chain application where the Input to the PE 15 also must feed another piece of equipment The outputs of the PE 15 also provide the choice between TRS connectors and XLR variety They also are wired in parallel and are actively balanced Both Outputs may be used simultaneously All XLR connectors used by Rane are wired per the IEC ANSI AES standard as follows pin 2 positive pin 3 negative and pin 1 chassis ground Unbalanced use of a PE 15 requires you to take some particular steps in wiring On the Input use either a mono 4 connector no ring or short pin 3 to pin 1 and drive pin 2 for XLR connectors On the Output leave pin 3 open and take the signal from pin 2
4. cord grounding pin or the rack screws to another grounded chassis 3 Units with outboard power supplies do NOT ground the chassis through the line cord Make sure that these units are grounded either to another chassis which is earth grounded or directly to the grounding screw on an AC outlet cover by means of a wire connected to a screw on the chassis with a star washer to guarantee proper contact Please refer to RaneNote 110 Sound System Interconnection elsewhere in this manual for further information on system grounding Manual 3 PE 15 CONNECTION The PE 15 is compatible with all line level 10 dBV and 4 dBu interfaces and products However guitars micro phones and other low level products must be preamplified before connecting to the PE 15 The proper connection of this unit to a system is a relatively simple matter the specifics of which may vary greatly depending on the application Use a PE 15 anywhere line level frequency contouring is required This includes live sound reinforcement systems recording studios clubs etc The most common location to insert a parametric equal izer is immediately preceding the active crossover or power amplifier This provides the means to correct loudspeaker deficiencies and other acoustic corrections required in any system for high quality reproduction Many systems employ both a graphic and parametric equalizer connected in series The graphic being used to correct for acoustic anom
5. ectronic device This switch allows power to flow from the source to the very soul of the PE 15 thereby empowering all its vital functions POWER indicator When this yellow LED is lit the unit is ready to serve OVERLOAD indicator illuminates red whenever the signal level at the Input Output or any of the five equalizer stages comes within 3 4 dB of clipping MASTER LEVEL control Full counterclockwise rotation of this control provides full Input attenuation full clockwise rotation yields 20 dB of gain through the unit Unity gain is approximately 12 00 Central Daylight Time Overall BYPASS switch Engaging this pushbutton provides a complete hard wire bypass of the PE 15 including signal ground In the out position the Input to the unit is processed through all of the active electronics This is a passive control requiring no power to operate Overall BYPASS indicator illuminates red when the unit is in the BYPASS mode created by BANDWIDTH controls Q Full counterclockwise rotation yields a bandwidth of octave Q 43 in the respective filter while full clockwise rotation gives a 1 5 octave Q 0 9 bandwidth Pulling this control to the out position on Bands 1 and 5 switches the filters to their Shelf Mode Filter LEVEL controls The center detent position guarantees flat response through the respective filter due to its grounded center tap Full clockwise rotation delivers 15 dB of boost while full cou
6. n achieving better sound As a notch filter the PE 15 works very well in increasing system headroom by attenuating system peaks that create feedback problems The obvious goal in notching is to remove only the problem areas and nothing else With this in mind it is always a good idea to first try to notch out feed back with the BW controls set to their full counterclockwise positions The acoustic resonances causing feedback are generally so narrow that a filter bandwidth set at 03 1 0 octave easily cures the problem To chase down the feedback frequency start with the filter LEVEL control set to its full 20 dB position With the BW still set to minimum tune the FREQ control until the feedback goes away It shouldn t take too much fine tuning to find the center of the resonance Once you have achieved stability advance the MASTER CON TROL until the feedback starts to reappear then back it down slightly If a 20 dB cut won t cure the problem the resonance is extreme and must be dealt with in other ways For example move the speakers or the mics hang some drapes move some walls burn down the building or simply unplug the system something must give REGARDING PE15 NOISE You may experience noise when using this unit with one or more bandwidth BW controls set to the narrowest 03 possible setting This is the noisiest possible setting The most usual use for this setting is deep notching e g for eliminating a specific f
7. nced Output The tip is signal positive the ring is signal negative and the sleeve is chassis ground This jack parallels the XLR Output connector and may be used simultaneously to give two Outputs For unbalanced applications the preferred choice is to use a TRS tip ring sleeve plug and leave the ring open however a standard TS mono plug may be substituted without damage XLR OUTPUT jack This Output parallels the above Wiring is per IEC ANSI AES standards pin 1 ground pin 2 posi tive and pin 3 negative Remote POWER supply input This unit is supplied from the factory with a Model RS 1 Remote AC Power Supply suitable for connection to this jack This unit requires an 18 volt AC center tapped transformer only This is not a telephone jack Never use a power supply other than the one supplied or a Rane approved replacement Chassis ground point A 6 32 screw is used for chassis grounding purposes See below for details CHASSIS GROUNDING If after hooking up your system it exhibits excessive hum or buzzing there is an incompatibility in the grounding configuration between units somewhere Your mission should you accept it is to discover how your particular system wants to be grounded Here are some things to try 1 Try combinations of lifting grounds on units that are supplied with ground lift switches or links 2 If your equipment is in a rack verify that all chassis are tied to a good earth ground either through the line
8. nterclockwise rotation yields 20 dB of cut FREQUENCY sweep controls set the center frequency of the filter band or the Turnover Frequency for Shelf Mode Available sweep range is approximately four octaves Filter BYPASS switches Each of the five filter BYPASS switches disables the respective filter providing instant compari son between flat response and equalized response Q Filter BYPASS LED illuminates when the band is in BYPASS created by 0 Manual 2 REAR PANEL DESCRIPTION Q TRS INPUT jack A differentially active balanced auto unbalanced 1 4 Input connector tip positive ring negative and sleeve chassis ground For unbalanced operation use a 2 conductor mono plug connect the tip to the signal line and the sleeve to ground If a 3 conductor plug is used for unbalanced operation be sure to ground the ring This Input parallels the XLR connector and may be used for daisy chaining purposes but may not be used to sum two different Inputs XLR INPUT jack This Input parallels the 4 connector and is wired pin 1 chassis ground shield screen etc pin 2 positive and pin 3 negative For unbalanced applications be sure to use pin 2 as hot and ground pin 3 Making this connec tion engages the auto unbalanced Input mode As above you may use this connector for daisy chaining to drive other equipment but it must not be used for summing purposes TRS OUTPUT jack This is an active bala
9. requency such as problems caused by feedback or other oscillations Most often only one filter is required It should also be noted there is a trade off between noise and desired results when using narrow bandwidth notching For example where the system correction achieved out weighs the noise levels generated by the required setting TEL 425 355 6000 FAX 425 347 7757 WEB http www rane com 103048

OPERATORS MANUAL PE 15

Contents

Download Pdf Manuals

Related Search

Related Contents