MOPSlcdLX
Contents
1. Header Pin 1 Signal Name Function 1 TXD 10 100 transmit positive 1 2 2 TXD 10 100 transmit negative 3 RXD 10 100 receive positive 4 GND Ground shield 8 5 GND Ground shield 6 RXD 10 100 receive negative 7 GND Ground shield 8 GND Ground shield MOPSIcdLX User s Guide KTD S0005 C Power Supply 17 Power Supply In some applications the 5 is intended for use as a stand alone module without a backplane You need to have a power connector available on the board for direct power supply The MOPSIcdLX is a 5V only board Peripherals can obtain additional voltage from the power connector next to the PC 104 bus The additional voltages 12V 5V and 12V are not generated onboard 17 1 Connector The power connector is available as 10000 8 pins Header Pin Signal Function 1 GND Ground 1 2 2 9 Power supply 45V 3 BATT Battery 7 4 12V 1 Power supply 12V 5 5y 1 Power supply 5V 6 12V 1 Power supply 12V 7 GND Ground 8 vcc 7 Power supply 45V Note 1 protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 17 2 Power Pins Every power pin on the power connector suppl2. E E E E TEA 24 16 LAN 0140 552 2 25 25 450245 25 16 1 socdessscdsdesendeccccseecicesseseedes doc bcos space essa deedescesssaebsugencessesdiseecegesseatesdeas 25 17 Power 40101 e Mn 26 17 1 esl e TT NEUE 26 17 2 Power ETT ET TTL 26 17 3 External Battery RR E M 27 18 bern ea 28 19 CPU Memory acis Se nemo Ed ep dai 29 20 Special Hardware Hi ES 30 20 1 TSA BUS LiMttat OMS OTT 30 20 2 30 20 3 BO 30 21 SCUT GUE iaar AME 31 21 1 Start PHOENIX AWARD BIOS Setup VUA CH hen VER YA CU PE RURR EET UN dti t ARR 31 21 2 Menu 32 21 3 EINER AERA ERE ATEM AREE 32 21 3 IDEMasterorSlave S bmieti oa vae celeb RETE 33 21 4 Advanced BIOS Features Ne 33 21 5 Advanced Chipset Features 2 rte Eee Coen eee etae een eno eros n oC aeu Ye e ada DRAN 35 21 6 Integrated Peripherals 2 52 2 err ree
3. Note 1 protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 MOPSIcdLX User s Guide KTD S0005 C USB Interface 13 USB Interface The USB interface comes with two USB ports which follow the OHCI EHCI specification and are USB 2 0 compliant You can expand the amount of USB connections by adding external hubs 13 1 Connector The USB ports are available through the X15006 and X15007 connectors each 4 pins To have the signals available on the standard USB interface connectors an adapter cable is required An USB interface cable is available from KONTRON KAB USB 2 part number 96054 0000 00 2 Header Pin SignalName Function 1 GND Ground 2 USB USB port positive 3 USB USB port negative 7 1 Power Note 1 protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 13 2 Limitations The power contacts for USB devices on pin 1 and pin 4 are protected They are suitable to supply connected USB devices with a maximum of 500 mA power dissipation Do not supply external USB de
4. 13 7 1 13 8 CS 14 8 1 CRI COD 14 8 2 Flat Panel Connector 14 8 2 1 PUT 15 8 3 Connecting a Flat Panel e eet eE eu Ee sese ae queen 16 8 4 Available Video une 16 8 5 Extended VESA sds ge Eae e 17 8 6 Backlight Enable Polarity 2 225 2 17 MOPSIcdLX User s Guide Table of Contents 9 Senat Port Intela MEET SEESH atest 18 9 1 esc TT 18 10 Parallel Port bet aCe fess quaa due vb ed a E V EYE HEEL Eden ER 19 10 1 19 11 PS 2 Keyboard BETTE RIS RETE TT 20 11 1 20 11 2 20 12 05 2 D dde a 21 12 1 feud TDI T TI TUUS 21 13 US 22 13 1 22 13 2 18 13 22 14 Floppy DES Mx Ma nid reta acus Ca FR 23 14 1 COMM COLON RETE ETE AED 23 15 EIDE Interface P ATA 24 15 1
5. Jo a e X15003 um m m Connector Layout Connector Locations LOOSLX S00SLX KTD S0005 C Appendix B B 1 95 9 90 81 gt gt 19 85 Z 5 lt 44 08 w S 5 Oo n w 24 gt 4 gt 4 3 68 8 a o e o o 15 KTD S0005 C B 2 4x 23 18 KTD S0005 C B 3 Mating Connectors Thetable notes mating connectors Appendix B Connector Layout Identifier Mating Connector Comment X12001 1 25 mm 6 pin for DSUB15 adaptation CRT MOLEX 51021 0600 or comp X14001 1 25 mm 4 pin for PS 2 mouse MOLEX 51021 0400 or comp X15000 2 54 mm 10 pin for DSUB9 adaption COMA COMB X15001 AMP 1 215882 0 or comp X15002 2 54 mm 10 pin for keyboard f
6. 36 MOPSIcdLX User s Guide Table of Contents 21 7 Comma seis m RR BE DAP HAMA Eq b NUN MU dea Odi MO 36 21 8 pr T I 37 21 9 Board 37 Appendix System ae 38 1 Interrupt Request IRQ 8299 xu epe inh ema externas QU RE ER eR ERN E HR he 38 A 2 Direct Memory Access DMA Channels pp 39 Memory 39 4 T O Address Ma ascen iei 40 5 DEVICES PR 41 A 6 System Management Bus SMBus pe 41 Appendix B Connector LAO MU vcwncswanssvanvieeamepndsa 42 B 1 Connector LOCATIONS 42 B 2 Mechanical Dimensions s 43 B 3 Gp 8 Ie 44 B 4 uod m 45 Appendix C Reference DOCUIBIES acusa cupa ese Eee y Sa YOq tO POUR INFR Me 49 Appendix D Document REVISION History sssesessesesesessssososesessososesesessesesesee 50 MOPSIcdLX User s Guide KTD S0005 C User Information 1 User Information 1 1 About This Document This
7. 3 D0 Data 0 2 4 ERR Error 15 5 01 Data 1 3 6 INIT Init 16 7 D2 Data 2 4 8 SLIN Select in 17 25 26 9 D3 Data 3 5 10 GND Ground 18 11 D4 Data 4 6 12 GND Ground 19 13 D5 Data 5 7 14 GND Ground 20 15 D6 Data 6 8 16 GND Ground 21 17 D7 Data 7 9 18 GND Ground 22 19 Acknowledge 10 20 GND Ground 23 21 BUSY Busy 11 22 GND Ground 24 23 PE Paper out 12 24 GND Ground 25 25 SLCT Select out 13 26 vcc 7 Power 5V Note 1 protect the external power lines of peripheral device make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 MOPSIcdLX User s Guide KTD S0005 C PS 2 Keyboard Interface 11 5 2 Keyboard Interface The keyboard and feature connector of the MOPSIcdLX offers four functions PS 2 Keyboard Speaker Battery Reset button 11 1 Connector The keyboard and feature connector is available through connector X15002 10 pins An adapter cable is required to connect a standard keyboard to this interface There is an adapter cable for the PS 2 keyboard available from KONTRON KAB KB PS2 part number 96060 0000 00 0 The adapter cables do not know the other functions on this interface Pin Signal Name Function 6 pin PS 2 1 SPKR Speaker 1 2 2 GND Ground 3 RESIN Reset input 9 40 4
8. Enabled LAN Controller Enabled Enables or disables the external PCI LAN con Disabled troller USB Controller Enabled Enables or disables the internal USB controller Disabled Watchdog Mode Disabled Selects operation mode Generate RESET Watchdog Timeout 1 sec 30 sec Selects maximum trigger period 1 30 5 min Watchdog Delay 1 sec 30 sec Selects time until the watchdog counter starts 1min 30 5 min the counting MOPSlcdLX User s Guide KTD S0005 C Setup Guide 21 6 Integrated Peripherals Feature Option Description Master Slave Drive PIO Auto Mode 0 Mode 1 Selects HDD PIO mode or Auto for optimum Mode Mode 2 Mode 3 Mode 4 transfer mode Master Slave Drive UDMA Disabled Disables UDMA or selects the optimum transfer Auto mode Bus Master Mode Disabled Enables or disables IDE bus master mode Enabled HDD Block Mode Disabled Enables or disables IDE block mode If the Enabled harddrive supports block mode select Enabled for automatic detection of the optimal number of block read writes per sector Keyboard Input Clock 6 8 12 16 MHz Selects the keyboard clock Floppy Controller Disabled Enables or disables the floppy controller Enabled Serial Port 1 2 Disabled Selects 1 0 base and IRQ of serial port respec 3F8 IRQ4 Port 1 tively disables the port 2F8 IRQ3 Port 2 4 2 Parallel Port Disabled Selects 1 0 base and IRQ of serial port respec 378 1807
9. parameters Memory speed 1 3 07 25 06 M H ttmann Added chapter Watchdog Timer and Onboard Device Configuration 1 2 07 12 06 M H ttmann Minor changes 1 1 07 07 06 S Laudan Basic reworking M H ttmann 1 0 05 16 06 S Laudan First revision Corporate Offices Europe Middle East amp Africa North America Asia Pacific Oskar von Miller Str 1 14118 Stowe Drive 17 Building Block 1 ABP AMD 85386 Eching Munich Poway CA 92064 7147 188 Southern West 4th Ring Road Germany USA Beijing 100070 P R China Tel 49 0 8165 77 777 Tel 1 888 294 4558 Tel 86 10 63751188 Fax 49 0 8165 77 219 Fax 1 858 677 0898 info kontron com info us kontron com info kontron cn MOPSlcdLX User s Guide
10. GND Ground 22 WRTPRT Write protect 23 GND Ground 24 RDATA Read data 25 GND Ground 26 HDSEL Side one select Note 1 protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 MOPSIcdLX User s Guide KTD S0005 C EIDE Interface P ATA 15 EIDE Interface P ATA The MOPSlcdLX features one EIDE interface UDMA33 66 mode that can drive two hard disks When two devices share a single adapter they are connected in a master slave daisy chain configuration If only one drive is connected you must set it as master 15 1 Connector The EIDE interface is available through connector X15005 44 pins This interface is designed in 2 mm grid for optimal connectivity to a 2 5 hard disk You can use two cables to directly connect a hard disk in a 2 5 form factor KAB IDE 2MM part number 96021 0000 00 0 or a 3 5 form factor KAB IDE 25 part num ber 96020 0000 00 0 Header Pin Signal Function Pin Signal Function 1 RESET Reset 2 GND Ground 3 D7 Data 7 4 D8 Data 8 5 D6 Data 6 6 D9 Data 9 7 D5 Data 5 8 D10 Data 10 9 D4 Data 4 10 D11 Data 11 11 D3 Data 3 12 D12 Data 12 13 D2 Data 2 14 D13 Data 13 15 D1 Data 1 16 D14 Data 14 17 DO Data 0 18 D15 Data 15 19 GND Ground 20 Key N C Key pi
11. PCI access possible Shadow Read Write Disabled Normally shadow area only readable Use this Enabled option to enable write operation Memory Hole at 15M 16M Disabled Enables or disables the memory hole at 15MB Enabled for ISA bus access MOPSIcdLX User s Guide KTD S0005 C Setup Guide 21 5 Advanced Chipset Features Feature Option Description CPU Frequency Auto 200 MHz 333 MHz Selects CPU frequency Auto uses board strap 400 MHz 433 MHz 500 MHz options Memory Speed DDR200 DDR266 DDR333 Selects memory speed Video Memory Size 8 16 32 64 128 254 MB Defines Video memory size The Video memory shares system memory Output Display CRT LCD LCD amp CRT Selects display boot devices CRT amp LCD is the simultaneous mode LCD Resolution Auto VGA SVGA XGA VGA to XGA provides standard timings for pa nel resolutions Auto loads a DisplayID record Record Protocol UDS EDID UDS not longer supported DisplayID DisplayID VESA specification Only valid if LCD Resolution Auto Color Depth 18 Bit Defines the LCD color depth 24 Bit Color Mode FPDI FPDI Flat Panel Display Interface LDI LDI LVDS Display Interface Only valid of Color Depth 24 Bit Backlight Value 0 10 20 30 40 50 60 Chooses a value to adjust backlight of the LCD 70 80 100 120 150 180 0 2 0 250 nearly maximal voltage 210 230 250 Security Block Disabled Enables or disables the internal Security Block
12. Setup values with optimized values Set Supervisor Password Change set or disable supervisor password Set User Password Change set or disable user password Save amp Exit Setup Saves Setup values to CMOS and exit Setup Exit Without Saving Discards all Setup values and exit Setup 21 3 Main Menu Feature Option Description Date MM DD YYYY Sets system date Time HH MM SS Sets system time IDE Master Drive Submenu Displays result of IDE autotyping IDE Slave Drive Submenu Displays result of IDE autotyping Drive None 360 kBits 5 Sets type of floppy disk drive 1 2 MBits 5 720 kBits 32 1 44 MBits 3 2 88 MBits 31 Halt On All Errors No Errors Determines if errors detected during boot up But Keyboard cause system to halt All But Diskette All But Disk Key Base Memory N A Displays amount of conventional memory de tected during boot up Extended Memory N A Displays amount of extended memory detected during boot up Extended memory capacity of memory modu le selected frame buffer memory size Total Memory N A Displays amount of total memory detected during boot up MOPSlcdLX User s Guide KTD S0005 C 21 3 1 Feature HDD Auto Detection IDE Master or Slave Submenu Option Press Enter Setup Guide Description Executes HDD auto detection Master Slave Drive None None disabl
13. configured with ease by taking advantage of this standard MOPS module feature 2 2 MOPSIcdLX Overview Please refer to the following matrix to choose the product that suits your needs best Article number 01036 0000 53 4 v 01036 0000 53 5 v v MOPSIcdLX User s Guide KTD S0005 C Specifications 3 Specifications 3 1 Functional Specifications Processor AMD Geode LX800 a 64 data and 64 kB instruction L1 cache a 128kBL2 cache a Integrated memory controller run with one DDR200 to DDR333 unbuffered DDR SDRAM 50 DIMM form factor up to 1GB Integrated display controller with dual display support CRT TFT and up to 254 MB video RAM UMA Chipset AMD Geode CS5536 64 bit 66 MHz GeodeLink interface External PCI bus with 32 bit 33 MHz operation PCI V2 2 compliant One parallel ATA PCI IDE controller Four USB channels only two channels available Onchip Video Graphics Array VGA CRT monitor interface resolution up to 1920x1440 pixel LVDS flatpanel interface supports single clock with 18 24 bit color depth resolution max 1024x768 pixel Onchip Parallel ATA P ATA o Supports PIO mode Multiword DMA and Ultra DMA up to UDMA5 Onchip Universal Serial Bus USB a Two ports are capable to handle USB1 1 and USB2 0 EHCI 5 1 0 LPC Winbond W83627DHG Two serial ports RS 232 compatible One parall
14. tively disables the port 278 IRQ5 3BC IRQ7 Parallel Port Mode Standard Standard bidirectional EPP EPP Enhanced Parallel Port specification EPP Mode Select EPP1 9 EPP1 7 Selects the EPP specification 21 7 PnP PCI Configurations Feature Option Description Init Display First Onboard Defines the search strategy for the primary ISA Slot graphic controller PCI Slot Reset Configuration Data Disabled Enabled erases all configuration data in Exten Enabled ded System Configuration Data ESCD Resources Controlled by Auto ESCD Manual allows user configuration of PCI IRQs Manual First PCI IRQ IRQ3 IRQ4 IRQ5 IRQ7 The system BIOS must have two PCI IRQs PCI Second PCI IRQ IRQ10 First interrupts own the highest priority and dis IRQ11 Second abling legacy ISA IRQs also internal serial 18012 18015 and parallel ports MOPSlcdLX User s Guide KTD S0005 C Setup Guide 21 8 PC Health Status Feature Option Description System Temp Local N A Local temperature CPU Die Temp Remote N A Temperature of CPU Shutdown Temperature Disabled Defines the shutdown temperature 60 65 70 75 80 85 90 95 100 Board Voltage N A Vcore voltage generated onboard Board Voltage 3 3V N A 3 3V voltage generated onboard System Voltage 5V N A 5V voltage external power supply System Voltage 12V N A 12V voltage externa
15. 04 D 1 N C Reserved VCC5 2 ADO 2 Vo AD2 AD1 VCC5 2 3 AD5 GND AD4 AD3 4 C BEO AD7 GND AD6 5 GND AD9 AD8 GND 6 AD11 Viyo AD10 Reserved 7 AD14 AD13 GND AD12 8 VCC3 C BE1 AD15 2 9 SERR GND Reserved PAR 10 GND PERR VCC3 Reserved 11 STOP VCC3 LOCK GND 12 VCC3 2 TRDY GND DEVSEL 13 FRAME GND IRDY 14 GND AD16 VCC3 C BE2 15 AD18 VCC3 AD17 GND 16 AD21 AD20 GND AD19 17 VCC3 2 AD23 AD22 VCC3 2 18 IDSELO AD20 GND IDSEL1 AD21 IDSEL2 AD22 19 AD24 C BE3 Wa IDSEL3 AD24 20 GND AD26 AD25 GND 21 AD29 VCC5 AD28 AD27 22 VCC5 2 AD30 GND AD31 23 REQO GND REQ1 24 GND REQ2 VCC5 2 GNTO 25 GNT1 GNT2 GND 26 VCC5 CLKO GND CLK1 27 CLK2 VCC5 CLK3 GND 28 GND INTD VCC5 2 RST 29 12 2 INTA INTB INTC 30 12V Reserved Reserved GND MOPSlcdLX User s Guide KTD S0005 C Appendix B Connector Layout P ATA Floppy LPT JILI X15005 X15003 X15004 X12000 1 RESET VCC5 STB N C 2 GND IDX AFD 3 D7 VCC5 2 DO 4 08 DRO ERR ENAVCC 5 D6 VCC5 2 D1 FTX1 6 D9 DSKCHG INIT FTX1 7 D5 N C D2 N C 8 D10 N C SLIN FTX2 9 D4 N C D3 FTX24 10 D11 MTRO GND GND 11 D3 N C D4 FTXC 12 D12 FDIR GND FTXC 13 D2 N C D5 GND 14 D13 STEP GND FTX3 15 D1 GND D6 FTX3 16 D14 WDATA GND SDA 17 D0 GND D7 RSVD 18 D15 WGATE GND RSVD 19 GND GND AC
16. 5 07 22 11 M H ttmann Replace the second picture in chapter Crisis Management S0005 B 01 24 11 M H ttmann Changed picture in chapter PCI Bus Expansion PCI and VCC added warning in chapter External Real Time Clock Battery 50005 08 10 10 M H ttmann Changes for pcb rev 5 00 and swap the pins of X12001 X15006 X15007 and X14001 S0005 0 12 16 09 M H ttmann Adapted to KONTRON Technology A S guidelines 2 6 10 13 08 D Zernikow Remove the chapter ISA Bus Timing 2 5 06 30 08 M H ttmann Added chapter ISA Bus Timing chapter UDS and DisplayID specification and the entry Board Information in the Setup Guide 2 4 02 27 08 M H ttmann Added Memory Hole 15M 16M in the Setup Guide 2 3 09 25 07 M H ttmann Delete DDR333 entry 2 2 09 17 07 M H ttmann Added 1 0 address range 290h 297h as reserved NT 07 20 07 M H ttmann Added some memory DDR SDRAM remarks and other minor changes 2 0 05 04 07 M H ttmann Added chapter Color Mode and Crisis Management Added new BIOS features from R109 Change Design 1 9 01 08 07 M H ttmann New KONTRON Design 1 8 01 03 07 M H ttmann Delete restriction of PCI clock signals PC104 connector 1 7 12 07 06 M H ttmann Change chapter Special BIOS Hints 1 6 11 07 06 M H ttmann Added chapter KONTRON BIOS Extension and some Setup entries 1 5 09 04 06 M H ttmann Change font added chapter Memory Issues 1 4 08 17 06 M H ttmann Added some chapters e g CPU Chipset and Super I O Modification of panel
17. CI IRQ for PCI Dynamic BIOS default 11 PCI IRQ for PCI Dynamic BIOS default 12 PS 2 Mouse No Note 1 13 Floating Point Unit FPU No 14 IDE Controller Primary No Note 1 15 IDE Controller Secondary No Note 3 Note 1 Ifthe Used for device is disabled in the BIOS Setup the corresponding interrupt is free 2 The parallel port also can be configured for IRQ5 3 Not usable in Windows since a PCI IDE controller uses always two channels MOPSIcdLX User s Guide KTD S0005 C Appendix A System Resources A 2 Direct Memory Access DMA Channels Used for Available Comment Yes Yes Floppy Controller No Note 1 Yes Cascade No No Note 2 No Note 2 No Note 2 OU Ww Note 1 Ifthe Used for device is disabled in the BIOS Setup the corresponding DMA channel is free 2 16 bit DMA channels not available A 3 Memory Area The first 640 kB of DRAM are used as main memory DOS can address 1 MB of memory directly Memory area above 1 MB high memory extended memory is accessed under DOS via special drivers such as HIMEM SYS Other operating systems Linux or Windows versions allow you to address the full memory area directly Memory Range Used for Comment 0000 C7FFFh VGA BIOS No C8000h CFFFFh Yes if onboard graphic controller is used 000001 DFFFFh Yes E0000h E7FFFh Yes Free for ISA bus
18. Clock Battery Voltage range Maximum current Lithium battery precautions CAUTION Danger of explosion if battery is incorrectly re placed Replace only with same or equivalent type recommended by manufacturer Dispose of used batteries according to the manufacturer s instruc tions ATTENTION Risque d explosion avec l change inad quat de la batterie Remplacement seulement par le m me ou un type quivalent recommand par le producteur L vacuation des batteries usag es conform ment des indications du fabricant ADVARSEL Lithiumbatteri Eksplosionsfare ved fejlagtig h ndtering Udskiftning kun ske med batteri af samme fabrikat og type Lev r det brugte batteri tilbage til leverand ren VARNING Explosionsfara vid felaktigt batteribyte Anv nd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren Kassera anvant batteri enligt fabrikantens instruktion Specifications 2 4V 3 6V typ 3 0V 10pA 3 0V VORSICHT Explosionsgefahr bei unsachgem Bem Austausch der Batterie Ersatz nur durch den selben oder einen vom Hersteller empfohlenen gleichwertigen Typ Entsorgung gebrauchter Batterien nach Anga ben des Herstellers PRECAUCION Peligro de explosi n si la bater a se sustituye incorrectamente Sustituya solamente el mismo o tipo equivalente recomendado por el fabricante Disponga las bater as usadas seg n las instrucciones d
19. E8000h FFFFFh System BIOS No MOPSlcdLX User s Guide KTD S0005 C Appendix A System Resources A 4 1 0 Address Map The I 0 port addresses of the MOPSIcdLX are functionally identical to a standard PC AT All addresses not mentioned in this table should be available We recommend that you do not use 1 0 addresses below 0100h with additional hardware for compatibility reasons even though they are available 1 0 Address Used for D VEVETITS Comment O1FOh 01F7h IDE Controller P ATA No Note 1 0278h 027Fh Yes Possible address of LPT2 0290h 0297h Hardware Monitor No O2E8h O2EFh Yes Possible address of COM4 O2F8h 02 Serial Port 2 No Note 1 0378h 037Fh Parallel Port 1 No Note 1 03BCh 03C4h Yes Possible address of LPT3 03BOh 03DFh Graphic Controller No 03E8h O3EFh Yes Possible address of COM3 03F7h Floppy Controller No Note 1 03F8h 03FFh Serial Port 1 No Note 1 0480h 048Fh DMA Extension No Chipset 04D0h 04D8h PIC Extension No Chipset 0A78h OA7Fh PnP Configuration No OCF8h OCFFh PCI Configuration No Chipset 6000h 63FFh AMD PCI ISA Bridge No Chipset 9COOh 9FFFh AMD PCI ISA Bridge No Chipset AC1Ch AC1Fh AMD PCI Host Bridge No Chipset FEOOh FEOFh AMD IDE Controller No Chipset FFOOh FF3Fh Intel LAN Controller No External PCI device 1 Ifthe Used for dev
20. G kontron Kontron User s Guide MOPSIcdLX KTD S0005 C Table of Contents Table of Contents 1 EGR 1 1 1 Phrase 1 1 2 C pyrig ht NOU CO e Dm 1 1 3 IGI 1 1 4 Si 1 1 5 EDICUAPEEP 1 1 6 Life SUpport POlCY ex 2 1 7 50 ceceni 2 2 vi vM tape DEM URS Ehe 3 2 1 MOPS Embedded Line Family pp 3 2 2 MOPSICALX OVGIVIGW 3 3 10 01 4 3 1 Functional Specifications eeu eae vs do serva ios 4 3 2 Block Did Gra ss os FURY E EN YER E eee 0a 6 3 3 Mechanical 5 5 tree 7 3 4 Electrical 5 5 7 3 5 External Real Time Clock Battery pe 8 3 6 Environmental Specifications ee 9 3 7 p fe 9 4 2 191 Ipsis i MT OR 10 5 11 6 ISA Bus 1 UE 12 6 1 12 6 2 HIMES 12 7 PCE BUS
21. HDD Second USB hard drive LAN LAN controller with LAN Boot ROM Disabled Third Disables boot device MOPSlcdLX User s Guide KTD S0005 C Setup Guide PXE LAN Boot Disabled Enables or disables the LAN boot option Enabled Boot Up Numlock Status Off On or Off turns NumLock on or off at boot up On keyboard feature Gate A20 Option Normal Normal keyboard controller checks Gate A20 Fast Fast lets chipset control Gate A20 Typematic Rate Setting Disabled Enables or disables manual adjustability Enabled Typematic Rate 6 8 10 12 15 20 24 30 Sets number of times to repeat a keystroke per chars sec second if you hold the key down Typematic Delay 250 500 750 1000 ms Sets delay time after key is held down before it begins to repeat the keystroke PS 2 Mouse Function Disabled Disabled prevents installed PS 2 mouse from Enabled functioning but frees IRQ12 Enabled forces the PS 2 mouse port to be ena bled regardless if a mouse is present Video BIOS Shadow Disabled Controls shadowing of Video BIOS Enabled C8000 CBFFF Range ISA PCI Bus ISA PCI bus enables normal ISA or PCI bus Range Shadow RAM access Reads an extension ROM from external D0000 D3FFF Range Ness Shadow RAM shadows an extension ROM on D4000 D7FFF Range ISA or PCI bus fast access D8000 DBFFF Range Reserved Memory sets the range as memory DCOO0 DFFFF Range no ISA or
22. K SCL 20 KEY N C TRKO GND RSVD 21 DRQ GND BUSY RSVD 22 GND WRTPRT GND N C 23 IOW GND PE RSVD 24 GND RDATA GND RSVD 25 IOR GND SLCT GND 26 GND HDSEL VCC5 2 RSVD 27 IOCHRDY RSVD 28 CSEL GND 29 DACK RSVD 30 GND RSVD 31 IRQ VCC5 32 N C VCC5 2 33 SA1 VCC5 2 34 ATAD VCC5 2 35 SAO BKLTON 36 SA2 GND 37 CS1 GND 38 CS3 1212 39 N C 412V 40 GND 1212 41 VCC5 2 42 VCC5 2 43 GND 44 N C MOPSlcdLX User s Guide KTD S0005 C Appendix B Connector Layout PS 2 Keyb PS 2 Mouse COMA COM B X15002 X14001 15000 15001 1 SPKR MSCLK DCD DCD 2 GND GND DSR DSR 3 RESIN VCC5 RXD RXD 4 RSVD MSDAT RTS RTS 5 KBDAT TXD TXD 6 KBCLK CTS CTS 7 GND DTR DTR 8 VCC5 RI RI 9 BATT GND GND 10 PWRGD VCC5 2 VCC5 2 CRT LAN USBA USB B X12001 X16000 X15006 15007 1 HSYNC TXD GND GND 2 VSYNC TXD USBO USBO 3 GND RXD USBO USBO 4 BLU GND VCC5 VCC5 5 GRN GND 6 RED RXD 7 GND 8 GND Note 1 Keypin for PC 104 GND for 104 specification 2 To protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 3 Not supported on the MOPSIcdLX board MOPSlcdLX User s Guide KTD S0005 C Appendix C
23. RSVD Reserved 5 KBDAT Keyboard data 1 6 KBCLK Keyboard clock 5 7 GND Ground 3 8 vcc Power 5V 4 9 BATT Battery 10 PWRGD Power good Note 1 To protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 11 2 Signal Description When POWERGD goes high it starts the reset generator on the CPU module to pull the onboard reset line high after a valid reset period You also can use this pin as a low active hardware reset for modules A battery signal BATT is not needed to hold CMOS setup data Your configurations for hard disks floppy drives and other peripherals are saved in an onboard EEPROM However you need a battery to save the CMOS date and time when power supply is turned off SPKR is an output to drive a piezo electronic speaker MOPSIcdLX User s Guide KTD S0005 C PS 2 Mouse Interface 12 PS 2 Mouse Interface The Super 1 0 of the MOPSIcdLX supports a PS 2 mouse 12 1 Connector The PS 2 mouse interface is available on connector X14001 4 pins An adapter cable is required to con nect a standard PS 2 mouse The cable is available from KONTRON KAB MOUSE PS2 part number 96062 0000 00 0 Signal Name Function 1 MSCLK Mouse clock 2 GND Ground 3 vcc 9 Power 5V 4 MSDAT Mouse data
24. Reference Documents Appendix C Reference Documents KONTRON Technology A S can t guarantee the availability of internet addresses Document Advanced Configuration and Power Interface ACPI Internet Address http www acpi info spec htm AT Attachment Storage Interface Specification ATA http t13 org Digital Visual Interface DVI http www ddwg org High Definition Audio Specification HD Audio http www intel com standards hdaudio High Speed Serialized AT Attachment S ATA http www sata io org developers IEEE 802 3 Specification Ethernet http standards ieee org getieee802 Low Pin Count Interface Specification LPC Bus http developer intel com design chipsets industry lpc htm Open LVDS Display Interface Standard Spec Open LDI http www national com analog displays open 101 PC 104 Specifications http www pc104 org pc104_specs php PCI Express Base Specification PCI Express http www pcisig com specifications SD Specification SD Card http www sdcard org developers tech sdio sdio_spec System Management Bus Specification SMBus http www smbus org specs Universal Serial Bus Specification USB http www usb org developers docs MOPSIcdLX User s Guide KTD S0005 C 50 Appendix D Document Revision History Appendix D Document Revision History Revision Date Author Changes 5000
25. T ISA bus is identical between C1 C18 and D1 D18 6 1 Connector The MOPSIcdLX features both XT bus and AT bus extension on two dual row socket connectors with 2 54 mm x 2 54 mm grid 0 1 x 0 1 The PC 104 XT bus is available through the X10000A connector The PC 104 AT bus is available through the X10000B connector 6 2 Hints PC 104 adapter cards are mounted in a stack through manner Adapter cards are designed with plugs on their undersides that mate with the PC 104 socket connectors of MOPSLcdLX PC 104 adapters can support the socket connector version on their topside and allow additional stacking of adapters Whenever possible use the MOPSIcdLX as top module of the PC 104 stack as the CPU board is normally the board with the highest heat dissipation MOPSIcdLX User s Guide KTD S0005 C PCI Bus Expansion 7 PCI Bus Expansion A quad row socket trough hole connector with a 2 x 2 mm 0 79 x 0 79 pitch implements the standard 32 bit PCI bus signals The PCI 104 bus is available through the standard connector X11000 A description of signals including electrical characteristics and timings is beyond the scope of this docu ment Please refer to the official PCI bus and PC 104 plus specifications for more details Under no circumstances 5V PCI cards may be used on the MOPSIcdLX board Only Universal and 3 3V add on cards are permitted and VCC are open default or set to 3 3V on the PCI bus 5V PCI add on cards ca
26. VESA Modes Test program SciTech VBETest VESA BIOS Extensions Compliance Test VESA Mode Type Pixels Colors 101h Graphic 640 x 480 256 103h Graphic 800 x 600 256 105h Graphic 1024 x 768 256 107h Graphic 1280 x 1024 256 110h Graphic 640 x 480 32k 111h Graphic 640 x 480 64k 112h Graphic 640 x 480 16M 32 bit 113h Graphic 800 x 600 32k 114h Graphic 800 x 600 64k 115h Graphic 800 x 600 16M 32 bit 116h Graphic 1024 x 768 32k 117h Graphic 1024 x 768 64k 118h Graphic 1024 x 768 16M 32 bit 119h Graphic 1280 x 1024 32k 11Ah Graphic 1280 x 1024 64k 11Bh Graphic 1280 x 1024 16M 32 bit 131h Graphic 1600 x 1200 256 133h Graphic 1600 x 1200 64k 134h Graphic 1600 x 1200 16M 32 bit 8 6 Backlight Enable Polarity Use a zero ohm bridge to define the backlight enable polarity Position 1 2 low active Position 2 3 high active TE L MOPSIcdLX User s Guide KTD S0005 C Serial Port Interfaces 9 Serial Port Interfaces Two fully functional serial ports COMA and COMB provide asynchronous serial communications COMA and COMB support RS 232 operation modes They are 16550 high speed UART compatible and support 16 byte FIFO buffers for transfer rates from 50 Baud to 115 2 KBaud 9 1 Connector COMA is available through the X15000 connector 10 pins and COMB through the X15001 connector 10 pins To have the signals available on the standard serial interface connector DSUB9 an adapter c
27. able is required A 9 pin DSUB cable is available from KONTRON KAB DSUB9 2 part number 96017 0000 00 0 The fol lowing table shows the pinouts for COMA and COMB as well as necessary connections for DSUB adapters Header 1 Signal Name Function 1 DCD Data carrier detect 1 1 2 2 DSR Data set ready 6 3 RXD Receive data 2 9 40 4 RTS Request to send 7 5 TXD Transmit data 3 6 CTS Clear to send 8 7 DTR Data terminalready 4 8 RI Ring indicator 9 9 GND Ground 5 10 vcc 7 Power 5V Note 1 To protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 MOPSIcdLX User s Guide KTD S0005 C Parallel Port Interface 10 Parallel Port Interface The MOPSIcdLX incorporates a parallel port that can be set to uni bidirectional and supports EPP operating modes 10 1 Connector The parallel port is available through the X15004 connector 26 pins To have the signals available on a standard parallel interface connector DSUB25 an adapter cable is required which is offered by KONTRON KAB DSUB25 1 part number 96015 0000 00 0 Header Pin Signal Name Function DSUB25 1 STB Strobe 1 1 2 2 AFD Autofeed 14
28. ash BIOS 11000 Bus ISA Bus X10000 X16000 i LAN Ethernet x10000 i82551ER LPC ISA Bridge F85226F Eeprom JIDA Watchdog AT24C04 W83627DHG X15002 4 5 2 E E dc Fl Serial Ports X14001 4 5 2 Mouse PPP onal Fol MAX211E RS 232 Eisen gt X15001 MOPSIcdLX User s Guide KTD S0005 C Specifications 3 3 Mechanical Specifications Dimensions gt 96 x 90 mm 3 77 x 3 55 gt Height on top approx 11 5 mm gt Height on bottom approx 10 5 mm 3 4 Electrical Specifications Supply Voltage gt 5V DC 5 Supply Voltage Ripple gt Maximum 100mV peak to peak 0 20 MHz Supply Current DOS prompt Power consumption tests were executed during the DOS prompt with 256 MB DDR SDRAM CRT monitor USB keyboard and CF card as boot device default BIOS settings FullLoad Softoff S5 1 10 5 50 0 20 1 00 Supply Current Windows XP SP3 The power consumption tests were executed during Windows XP SP3 by using a tool to stress the CPU 100 load and extensive 2D graphic The boards were ran with 256 MB DDR SDRAM CRT monitor PS 2 keyboard USB mouse and a CF card as boot device default BIOS settings Full Load Idle IW A IW 1 45 7 25 0 95 4 75 MOPSIcdLX User s Guide KTD S0005 C 3 5 External Real Time
29. ct your board supplier for technical support Before contacting support please be prepared to provide as much information as possible Board identification Type Part number find PN on label a Serial number find SN on label Board configuration DRAM type and size o BIOS revision find in the BIOS Setup BIOS settings different than default settings refer to the BIOS Setup section System environment a 0 5 type version o Driver origin and version Attached hardware drives USB devices LCD panels MOPSIcdLX User s Guide KTD S0005 C Introduction 2 Introduction 2 1 MOPS Embedded Line Family Each MOPS is a member of the PC 104 SBC family of KONTRON Technology A S MOPS embedded line modules are characterized by interfaces for 2 x USB Fast LAN PS 2 keyboard and mouse connector an ISA bus CRT interface as well as serial and parallel ports These homogeneous features facilitate easy upgrades within the MOPS embedded line product family Con nection of LCD panels is simplified when using the onboard standard JILI 40 pins or JILI30 interface As part of the standard features package all MOPS modules come with a JIDA interface which is integrated into the BIOS of the SBC modules This interface enables hardware independent access to the MOPS fea tures that can t be accessed via standard APIs Functions such as watchdog timer brightness of panel backlight and user bytes in EEPROM can be
30. document provides information about products from KONTRON Technology A S and or its subsidiaries No warranty of suitability purpose or fitness is implied While every attempt has been made to ensure that the information in this document is accurate the information contained within is supplied as is no liability is taken for any inaccuracies Manualis subject to change without prior notice KONTRON assumes no responsibility for the circuits descriptions and tables indicated as far as patents or other rights of third parties are concerned 1 2 Copyright Notice Copyright O 2006 2011 KONTRON Technology A S ALL RIGHTS RESERVED No part of this document may be reproduced or transmitted in any form or by any means electronically or mechanically for any purpose without the express written permission of KONTRON Technology A S 1 3 Trademarks Brand and product names are trademarks or registered trademarks of their respective owners 1 4 Standards KONTRON Technology A S is certified to ISO 9000 standards 1 5 Warranty This product is warranted against defects in material and workmanship for the warranty period from the date of shipment During the warranty period KONTRON Technology A S will at its discretion decide to repair or replace defective products Within the warranty period the repair of products is free of charge as long as warranty conditions are observed The warranty does not apply to defects resulting from improper or inadeq
31. e drive Auto Auto auto detection the drive itself suppli Manual es the information Manual user supplies the HDD information Access Mode CHS CHS physically 28bit addressing mode LBA LBA mode with logical block numbers Large Large for drives that do not support LBA and Auto have more than 1024 cylinders Auto auto detection the drive itself suppli es the information Capacity N A Displays the calculated size of the drive Cylinder N A Number of cylinders Head N A Number of read write heads Precomp N A Write precompensation cylinder number Landing Zone N A Defines the head park position Sector N A Number of sectors per track 21 4 Advanced BIOS Features Feature Option Description Security Option Setup Setup password required for Setup System System password required for system boot CPU Internal Cache Disabled Enables or disables internal cache Enabled JRC Extension Enabled Enables or disables the JRC extension remote Disabled control Darkboot Custom Logo Disabled If enabled normally darkboot will be active Enabled For custom logo contact KONTRON Virus Warning Enabled Enables or disables the virus warning for IDE Disabled harddisk boot sector First Boot Device Floppy Standard legacy diskette drive Second Boot Device Harddisk 0 First IDE hard drive Harddisk 1 IDE hard drive Third Boot Devi CDROM Standard CDROM or DVD drive USB FDD USB diskette drive USB ZIP USB ZIP drive e g IOMEGA USB CDROM USB CDROM drive USB
32. eature connector AMP 1 215882 0 or comp X15004 2 54 mm 26 pin for DSUB25 adaption LPT AMP 2 215882 6 or comp X15005 2 mm 44 pin for IDE connector Berg 89361 144 or comp X15006 1 25 mm 4 pin for USB connectors X15007 MOLEX 51021 0400 or comp X16000 2 mm 8 pin for RJ45 adaption Berg 90311 008 or comp MOPSIcdLX User s Guide KTD S0005 C B 4 Pinout Tables Appendix B Connector Layout PC 104 A PC 104 B PC 104 C PC 104 D 0 GND GND 1 IOCHCK GND SBHE MEMCS16 2 SD7 RESET LA23 10 516 3 506 VCC5 2 LA22 IRQ10 4 SD5 IRQ9 LA21 18011 5 504 5V 9 LA20 IRQ12 6 SD3 DRQ2 LA19 IRQ15 7 502 12V LA18 IRQ14 8 SD1 0WS LA17 DACKO 9 SDO 12 2 MEMR DRQO 10 IOCHRDY GND MEMW DACK5 11 AEN SMEMW SD8 DRQ5 12 SA19 SMEMR 509 DACK6 13 SA18 10W SD10 DRQ6 14 SA17 IOR SD11 DACK7 15 SA16 DACK3 SD12 DRQ7 16 SA15 DRQ3 SD13 VCC5 2 17 SA14 DACK1 SD14 MASTER 18 SA13 DRQ1 SD15 GND 19 SA12 REFRESH N C GND 20 SA11 SYSCLK 21 SA10 IRQ7 22 SA9 IRQ6 23 SA8 IRQ5 24 SA7 IRQ4 25 SA6 IRQ3 26 SA5 DACK2 27 SA4 T C 28 SA3 BALE 29 SA2 VCC5 30 SA1 OSC 31 SAO GND 32 GND GND MOPSlcdLX User s Guide KTD S0005 C Appendix B Connector Layout PCI 104 A PCI 104 B PCI 104 C PCI 1
33. el fabricante ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten Brukte batterier kasseres i henhold til fabrikantens instruksjoner VAROITUS Paristo voi r j ht jos se on virheellisesti asennettu Vaihda paristo ainoastaan lalteval mistajan suosittelemaan tyyppiln H vit k ytetty paristo valmistajan ohjeiden mukaisesti ATTENTION Do not connect the RTC battery to the MOPSIcdLX until just before the supply power is to be applied to the system When the battery is connected without power applied to the system the battery current might be in some cases higher than normal refer to AMD Geode CS5536 Companion Device Silicon Revision B1 Specification Update This can lead to a shorter lifetime of the RTC battery After the supply power has been applied to the system once after connecting the RTC battery the regular current is drained from the battery again MOPSIcdLX User s Guide KTD S0005 C Specifications 3 6 Environmental Specifications Temperature Operating with original KONTRON heat sink gt Ambient temperature 0to 60 1 Non operating gt Ambient temperature 10 to 85 C Note 1 Itis customer s responsibility to provide sufficient airflow around each of the components to keep them within the allowed temperature range Humidity Operating 1090 to 90 non condensing Non operati
34. el port configurable as enhanced parallel port EPP with bidirectional capability One legacy floppy interface PS 2 keyboard and mouse controller Watchdog timer na MOPSIcdLX User s Guide KTD S0005 C Specifications Fast Ethernet PCI Intel 82551ER a Full duplex operation at 10 100 Mbps o Fully compliant with IEEE 802 3 and IEEE 802 3u External ISA bus LPC Fintek F85226F a One PC 104 bus connector 8 16 bit 1 0 and memory access a ALLISA interrupts and 8 bit signals available 16 bit DMA not supported Bus master mode not supported External PCI bus o One PCI 104 bus connector only 3 3V PCI cards supported BIOS AWARD 512 kb Flash BIOS Real Time Clock RTC with CMOS RAM MOPSIcdLX User s Guide KTD S0005 C Specifications 3 2 Block Diagram MOPSIcdLX CPU AMD Geode 800 LVDS Graphic SDRAM DDR X12000 LVDS Controller Controller gt gt SDRAM ED X8000 1 2001 CRT o PCI Bus Temp Sensor 4e SMBus LM86 como gt 15005 Companion AMD contol USB 0 1 X15006 CS5536 X15007 LPC Bus FWH Fl
35. ement is limited to a maximum current and the following limitations apply Power Number of Pins Max Current per Pin VCC 45V 2 1A 5V 1 1A 12V 1 1A 12V 1 1A Note MOPSIcdLX is not a replacement for a backplane Use all power pins on the power connector the PC 104 con nectors for power supply to the MOPSIcdLX and also use all additional power connectors on additional 1 0 cards if your system exceeds the above limitations It is not acceptable to use only the power pins of PC 104 connector for power supply to the full PC 104 stack MOPSIcdLX User s Guide KTD S0005 C Power Supply 17 3 External Battery You can connect an external battery to pin 3 BATT of the power connector instead of pin 9 of the key board connector For more information refer to the keyboard chapter of this manual Attention Pin 3 power connector and pin 9 keyboard connector are connected to the same signal The pins are not decoupled therefore do not connect two batteries MOPSIcdLX User s Guide KTD S0005 C Crisis Management 18 Crisis Management Modifying parameters in the BIOS Setup implies the risk of leaving your system in a unbootable state In case this happens two jumper exists to reset the settings to Fail Safe values In case no battery is connected then follow these five steps Power down the system Remove the tagged jumper JP14002 see the picture Power up the system and
36. enter the BIOS Setup Before saving your new settings with Save amp Exit put the jumper back The board should be functional now 749010012 1011 In casethere is backup battery for the real time clock Power down the system Switch the second jumper JP7000 as depicted and wait for 3 seconds the jumper back as it was before Then continue with the steps from the no battery case MOPSIcdLX User s Guide KTD S0005 C CPU Memory Speed 19 CPU Memory Speed Not every combination of CPU and memory clock frequency is possible To ensure functionality of the board please make sure to use only combinations from the following table CPU Speed Memory Speed 200 MHz DDR200 333 MHz DDR200 333 MHz DDR266 333 MHz DDR333 400 MHz DDR200 400 MHz DDR266 400 MHz DDR333 433 MHz DDR266 433 MHz DDR333 500 MHz DDR266 500 MHz DDR333 MOPSIcdLX User s Guide KTD S0005 C Special Hardware Hints 20 Special Hardware Hints 20 1 ISA Bus Limitations TheISA bus implementation has the following four restrictions 16 bit DMA cycles located at DMA5 DMA7 are not supported An ISA device may take control of the bus ISA bus master mode This mode is not sup ported Simultaneous usage of standard legacy floppy and DMA cycles is not possible Using ISA graphic cards certain high color depth graphic modes may show disturbances i e ver
37. graphic controller and processor Therefore the full memory size is not available for software applications Up to 254 MB of system memory are used as graphic memory Attention 008400 modules can only be operated with the DDR333 timing MOPSIcdLX User s Guide KTD S0005 C ISA Bus Expansion 6 ISA Bus Expansion The design of the MOPSIcdLX follows the standard PC 104 form factor and offers ISA bus signals for the use of standard PC 104 adapter cards The PC 104 bus consists of two connectors that use 104 pins in total XT bus connector 64 pins AT bus connector 40 pins which is optional for 16 bit data bus system The pinout of the PC 104 bus connectors corresponds to the pinout of the ISA bus connectors with some added ground pins The two PC systems with different form factors are electrically compatible The XT bus connector row A and B The corresponding 64 pin stackthrough header ISA bus 62 pins has two added ground pins at the end of the connector pin A32 and pin B32 The pinout between PC 104 bus and XT ISA bus is identical between 1 A31 and B1 B31 The AT bus extension connector row C and D The corresponding 40 pin stackthrough header ISA bus 36 pins has four added ground pins two on each side of the connector To avoid confusion the first two pins are defined as pin CO and pin DO The additional ground pins at the end of the connector are defined as C19 and D19 The pinout between PC 104 bus and A
38. ice is disabled in the BIOS Setup the corresponding address is free MOPSlcdLX User s Guide KTD S0005 C Appendix A System Resources A 5 PCI Devices All devices follow the Peripheral Component Interconnect 2 2 PCI 2 2 specification Please see the speci fication for more details PCI Device PCIIRQ Comment Host Bridge None Chipset Graphics Controller INTA Chipset ISA Bridge None Chipset IDE Controller None Chipset USB Controller 1 INTD Chipset USB Controller 2 INTD Chipset Encryption Controller INTA Chipset LAN Controller INTA PCI bus AD19 A 6 System Management Bus SMBus The MOPSlcdLX uses an onboard System Management Bus SMBus This bus is not available on a peripheral connector and therefore cannot be used for external SMBus devices SMBus Address Device Comment 98h 99h Temperature Sensor LM86 AOh Ath SPD EEPROM DDR SDRAM Part of the DDR RAM module Warning There are more devices connected to the SMBus than listed in this table but access to these devices in not permitted Don t access any other device addresses except those listed above MOPSIcdLX User s Guide 000SLX V00SLX c00S LX W Pin 1 gt gt l 8 D 85 Z fe feu fen lt EEEE CEE X10000 X12001 X15006 X15007 22 a
39. ignal 2 6 RED Red video signal 1 8 2 Flat Panel Connector The LVDS interface for the flat panel is available through the X12000 connector 40 pins on the top side of the board The implementation of this subsystem complies with the JILI specification of KONTRON Techno logy A S A variety of cables for different display types are available from KONTRON Please refer to the actual cable list on the KONTRON website for part numbers and cable names When using a LCD additional voltages may be required to drive the displays logic and supply the backlight converter The display logic may require 5V or 3 3V backlight converters usually are 5V or 12V types When using a KONTRON JILI cable you do not need to determine such configurations Display logic voltage come preconfigured on the JILI cable On occasion backlight voltage has to be adjusted on the cable Even though the MOPSIcdLX is 5V only board you need to supply the 12V for the backlight converter addi tionally when using such a converter type MOPSIcdLX User s Guide KTD S0005 C Graphics Interface 8 2 1 Connector Header i Signal Name Function 1 N C Not connected 2 FTXO First channel data output 0 negative 3 First channel data output 0 positive 4 ENAVCC Enable panel power 5 FTX1 First channel data output 1 negative 6 FTX1 F
40. irst channel data output 1 positive 7 N C Not connected 8 FTX2 First channel data output 2 negative 9 FTX2 First channel data output 2 positive 10 GND Ground 11 First channel clock output negative 12 FTXC First channel clock output positive 13 GND Ground 14 FIX3 First channel data output 3 negative 15 First channel data output 3 positive 16 SDA I2C data line 17 RSVD Reserved 18 RSVD Reserved 19 SCL I2C clock line 20 RSVD Reserved 21 RSVD Reserved 22 N C Not connected 23 RSVD Reserved 24 RSVD Reserved 25 GND Ground 26 RSVD Reserved 27 RSVD Reserved 28 GND Ground 29 RSVD Reserved 30 RSVD Reserved 31 34 vcc 7 Power 45V 35 BKLTON Backlight on 36 37 GND Ground 38 40 VDD 1 Power 12V if voltage is connected Note 1 protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 MOPSlcdLX User s Guide KTD S0005 C Graphics Interface 8 3 Connecting a Flat Panel To determine whether your flat panel is supported check the KONTRON website for panel lists We regularly update the list of panels that have been tested with the MOPSIcdLX If you use one of those adapters supplied by KONTRON configuration is easy Check whether you have the correct adapter and cable for the panel you p
41. l power supply 21 9 Board Information Feature Option Description BIOS Version N A Shows the actual BIOS version BIOS Date N A Shows the BIOS production date LX800 Chip Rev N A Shows the Northbridge LX800 chip revision 55536 Chip Rev N A Shows the Southbridge CS5536 chip revision CPLD Revision N A Shows the CPLD revision Board Class N A Shows the KONTRON specific board class Board Name N A Shows the KONTRON specific board name Hardware Version N A Shows the KONTRON specific hardware version Manufacturing Date N A Shows the KONTRON specific manufacturing date Serial Number N A Shows the KONTRON specific serial number Boot Counter N A Shows the actual boot counter MOPSlcdLX User s Guide KTD S0005 C Appendix A System Resources Appendix A System Resources Interrupt Request IRQ Lines Please note that KONTRON PC 104 devices were designed after the draft of P996 Specification for ISA systems Because of this shareable interrupts are not supported Please ensure that the chosen interrupt is not already in use by PCI devices IRQ Used for Comment 0 Timer 0 No 1 Keyboard No 2 8259 Slave Cascade No 3 Serial Port 2 COM2 No Note 1 4 Serial Port 1 COM1 No Note 1 5 Yes Note 2 6 Floppy Controller No Note 1 7 Parallel Port LPT1 No Note 1 8 Real Time Clock RTC No 9 Yes 10 P
42. lan to use Inspect the cable for damages Disconnect the power from your system Connect the cable to the flat panel connector X12000 on the MOPSIcdLX and connect the other end to your JILI adapter connect the JILI adapter and the display Connect the backlight converter Supply power to your system If no image appears on your display connect a CRT monitor to the CRT connector If necessary program the EEPROM on the JILI cable with the matching configuration data If you still do not see improvement consider contacting the dealer for technical support 8 4 Available Video Modes The following list shows the video modes supported by the graphics controller with maximum frame buffer size When configured for saller frame buffers and or using a flat panel on the JILI interface not all of the video modes listed below may be available Capability depends on system configuration and on display capabilities Different operating systems also may not support all listed modes by the available drivers Video Mode Type Characters Pixels Colors 00h 01h Text 40x25 16 02h 03h Text 80x25 16 04h 05h Graphic 320 x 200 4 06h Graphic 640 x 200 2 07h Text 80 x25 2 ODh Graphic 320 x 200 16 OEh Graphic 640 x 200 16 OFh Graphic 640 x 350 2 10h Graphic 640 x 350 4 11h Graphic 640 x 480 2 12h Graphic 640 x 480 16 13h Graphic 320 x 200 256 MOPSIcdLX User s Guide KTD S0005 C Graphics Interface 8 5 Extended
43. n 21 DRQ DMA request 22 GND Ground 23 10W 1 0 write 24 GND Ground 25 IOR I 0 read 26 GND Ground 27 IOCHRDY 1 0 channel ready 28 CSEL 2 Cable select 29 DACK acknowledge 30 GND Ground 31 IRQ Interrupt request 32 N C Not connected 33 SA1 Address 1 34 ATAD UDMA detection 35 SAO Address 0 36 SA2 Address 2 37 51 Chip select 1 38 53 Chip select 3 39 N C Not connected 40 GND Ground 41 vcc 2 Power 5V 42 vcc 9 Power 5V 43 GND Ground 44 N C Not connected Note 1 protect the external power lines of peripheral devices make sure that the wires have the right diameter to withstand the maximum available current to enclosure of the peripheral device fulfills the fire protecting conditions of IEC EN 60950 2 Pin 28 is connected with 4700 to Ground for Cable Select IDE devices MOPSIcdLX User s Guide KTD S0005 C LAN Controller 16 LANController The MOPSIcdLX uses an Intel 82551ER PCI Fast Ethernet controller The controller support 10 100 Base T interfaces The devices auto negotiates the use ofa 10 or 100 Mbps connection Additionally it is possible to enable the LAN PXE Boot in the BIOS Setup to allow the system to boot up via a network connection from a PXE server 16 1 Connector The LAN interface is available through the connector X16000 8 pins To have the signals available on a standard RJ45 connector you need an adapter cable which is offered by KONTRON KAB MOPS ETN1 part number 96048 0000 00 0
44. n irretrievably damage the MOPSIcdLX board due to short curcuit with or VCC Before using a PCI add on card please make absolutely sure that this card is conform to these requirements The LX chipset does only support a 3 3V PCI bus 7 1 Configuration of The default settings for and VCC are not connected If it is ensured that the PCI expansion cards are types of 3 3V only zero ohm bridges can be set THERE ai Attention 5V PCI expansion cards can damage the board Please note that the 5V supply voltage is routed to the connector Four slots are available via the connector X11000 IDSEL IRQ but only three slots are busmaster capable MOPSIcdLX User s Guide KTD S0005 C Graphics Interface 8 Graphics Interface The graphics accelerator supports CRT monitors and a variety of LCD panels with single clock color depths of 18 24 bit and resolutions up to 1920x1440 for CRT and XGA 1024x768 for LCD 8 1 CRT Connector The CRT monitor interface is available through the X12001 connector 6 pins To have the signals available on a standard DSUB15 CRT monitor connector an adapter cable is required A 15 pin DSUB cable is avail able from KONTRON KAB VGA 2 part number 96053 0000 00 0 Header Pin Signal Function DSUB15 1 HSYNC Horizontal sync 13 2 VSYNC Vertical sync 14 3 GND Ground 5 8 4 BLUE Blue video signal 3 5 GREEN Green video s
45. ng 5 to 95 non condensing 3 7 MTBF The following MTBF Mean Time Between Failure values were calculated using a combination of manufac turer s test data if the data was available and a Bellcore calculation for the remaining parts The Bellcore calculation used is Method 1 Case 1 In that particular method the components are assumed to be operating at a 50 stress level in a 40 C ambient environment and the system is assumed to have not been burned in Manufacturer s data has been used wherever possible The manufacturer s data when used is specified at 50 C so in that sense the following results are slightly conservative The MTBF values shown below are for a 40 C in an office or telecommunications environment Higher temperatures and other envi ronmental stresses extreme altitude vibration salt water exposure etc cause lower MTBF values System MTBF hours tbd Note Fans usually shipped with KONTRON Technology A S products have 50 000 hour typical operating life The above esti mation assumes no fan but a passive heat sinking arrangement Estimated RTC battery life as opposed to battery failures is not included in the MTBF calculation The RTC battery lifetime has to be considered separately Battery life depends on both temperature and operating conditions When the KONTRON unit has external power the only battery drain is from leakage paths MOPSIcdLX User s Guide KTD S0005 C Getting Started 4 Getting Sta
46. on keys Item Specific Help Window Bottom or left side Help for selected item Menu Bar The menu bar at the upper half of the window lists different menus Use the arrow keys to make a selection Legend Bar Use the keys listed in the legend bar on the bottom to make your selections or exit the current menu Selecting an Item Use the or key to move the cursor to the field you want Then use the and keys to select a value for that field Displaying Submenus Use the arrow keys to move the cursor to the submenu you want Then press Enter A pointer gt marks all submenus Note Inthe Option column bold shows default settings MOPSIcdLX User s Guide KTD S0005 C 21 2 Menu Bar Feature Standard CMOS Features Setup Guide Description Defines time date harddisk and floppy type Advanced BIOS Features Defines virus warning boot sequence keyboard and mouse parameters Advanced Chipset Features Defines clocks video settings LAN USB and watchdog features Integrated Peripherals Defines IDE global settings and onboard devices COM LPT PnP PCI Configuration Defines graphic boot device and PCI memory resources PC Health Status Shows temperatures voltages and defines shutdown temperature Board Information Shows BIOS version date serial number and others Load Fail Safe Defaults Overwrite Setup values with fail safe values Load Optimized Defaults Overwrite
47. rted Getting started with the MOPSIcdLX is very easy Take the following steps Plug a suitable DDR SDRAM memory module into the RAM socket Plug the MOPSLcdLX to the PC 104 bus connector on the starter kit baseboard Make all necessary connections from the MOPSIcdLX to the starter kit board cables come with the starter kit The starter kit board offers various interfaces on standard connectors Connect the CRT monitor to the CRT interface or a LCD panel to the JILI interface by using the corresponding adapter cable Plug a keyboard and or mouse to the PS 2 connectors og occ Plug a data cable to the hard disk interface Attach the hard disk to the connector at the oppo site end of the cable If necessary connect the power supply to the hard disk s power connec tor Make sure all your connections have been made correctly Turn on the power 9 Enter the BIOS by pressing the Del key during boot up Make all changes in the BIOS Setup See the BIOS Setup chapter of this manual for details MOPSIcdLX User s Guide KTD S0005 C System Memory 5 System Memory The MOPSIcdLX uses only 200 pin Small Outline Dual Inline Memory Modules SODIMMs One socket is available for 2 5V unbuffered DDR200 up to DDR333 SDRAM of up to 1 GB The total amount of memory available on the SDRAM module is used for main memory and graphic memory on the MOPSIcdLX Shared Memory Architecture SMA manages the sharing of system memory between
48. tical lines This is due to non optimum timings in the FINTEK ISA bridge which cannot be fixed 20 2 PCI Bus Limitations The PCI bus implementation has the following three restrictions gt Only 3 3V PCI boards cards are supported do not use 5V PCI boards cards without level shifter Only PCI boards cards with speed of 33 MHz will be run Some problems exists when using the KONTRON ADA9 Evaluation Board refering to PCI slots KONTRON cannot guarantee that all PCI cards runs error free 20 3 Security Block The standard version of AMD LX800 doesn t contain an EEPROM for storing a hidden key Please contact KONTRON for further information MOPSIcdLX User s Guide KTD S0005 C Setup Guide 21 Setup Guide The PHOENIX AWARD BIOS Setup utility changes system behavior by modifying the BIOS configuration The Setup program uses a number of menus to make changes and turn features on or off Whenever you contact technical support about BIOS issues providing a BIOS version lt PLX8R gt is espe cially helpful 21 1 Start PHOENIX AWARD BIOS Setup Utility To start the PHOENIX AWARD BIOS Setup utility press DEL when the following string appears during boot up Press DEL to enter Setup The main menu then appears The Setup screen is composed of several sections Setup Screen Location Function Menu Bar Upper half Lists and selects all top level menus Legend Bar Near bottom or bottom 11515 Setup navigati
49. uate maintenance or handling by the buyer unauthorized modification or misuse operation outside of the product s environmental speci fications or improper installation or maintenance KONTRON Technology A S will not be responsible for any defects or damages to third party products that are caused by a faulty KONTRON Technology A S product MOPSIcdLX User s Guide KTD S0005 C User Information 1 6 Life Support Policy KONTRON Technology s products are not for use as critical components in life support devices or systems without express written approval of the general manager of KONTRON Technology A S As used herein Life support devices or systems are devices or systems which a are intended for surgical implant into body or b support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labelling can be reasonably expected to result in significant injury to the user A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness 1 7 Technical Support Please consult our Web site at http www kontron com support for the latest product documentation utilities drivers and support contacts or use the special e mail address sbc support 2 kontron com for technical problem In any case you can always conta
50. vices with higher power dissipation through these pins MOPSIcdLX User s Guide KTD S0005 C Floppy Drive Interface 14 Floppy Drive Interface The floppy drive interface of the MOPSIcdLX uses 2 88 MB Super I 0 floppy disk controller and can sup port one floppy disk drive with densities that range from 360 kB to 2 88 MB The controller is 100 IBM compatible 14 1 Connector The floppy disk interface is available on the flat foil connector X15003 26 pins This type of connector is often internally used in notebooks to connect a floppy drive Accessories are available for this interface from KONTRON To connect a standard 3 5 floppy drive use an adapter cable ADA FLOPPY 2 part number 96001 0000 00 0 If you have a slim line 3 5 floppy drive you may need a flat foil cable KAB FLOPPY MOPS 1 part number 96019 0000 00 0 It also is possible to get a slim line 3 5 floppy drive with cable FLOPPY MOPS 1 part number 96010 0000 00 0 Header Pin Signal Name Function Pin Signal Function 1 Power 45V 2 IDX Index 1 3 vcc Power 5V 4 DRO Drive select 0 5 Power 5 6 DSKCHG Disk change 7 N C Not connected 8 N C Not connected 9 N C Not connected 10 MTRO Motor on 0 11 N C Not connected 12 FDIR Direction select 13 N C Not connected 14 STEP Step 15 GND Ground 16 WDATA Write data 17 GND Ground 18 WGATE Write gate 19 GND Ground 20 TRKO Track 0 21
Download Pdf Manuals
Related Search
MOPSlcdLX