User's Guide IBM 3482/3487 Interface Kit
Contents
1. _ im Vertrieb von instal AMBOARD Electronics PN Connecting Display Module to MBC RGB Buffer Extron Electronics I INTERFACING SWITCHNG AND DISTRIBUTION r 4 euro Before connecting to power proceed by connecting the display module to the MBC RGB Buffer assembly as described below Connect the MBC IBM 3482 87 cable 1 from the logic module to the MBC RGB Buffer 2 as shown in Figure 10 Connect the MBC RGB Buffer cable 3 to the analog input of the selected interface The MBC RGB Buffer is compatible with the RGB 118 118 Plus 120 108 Plus and 202 Plus interfaces Restore power and adjust 2 the respective interface features to obtain the best visual presentation User s Guide Special Note The Blue Enhance control is provided on the MBC RGB Buffer for the purpose of brightening the primary blue color within the color palette in order to attain a color display similar to the IBM terminal Increasing the bright ness de saturating of the primary blue allows easy viewing of blue detail on projection applications As the Blue Enhance control is advanced some effect can be seen on magenta graphics The magenta will tend to de saturate This is a normal side effect of the Blue Enhance feature Adjust the Blue Enhance for best overall performance At this time adjust the blue enhance control on the MBC RGB Buffer to achieve the desired blue color This completes installation of the IBM 3482 82. 7 Interface Kit Infowindow II is a registered trademark of the International Business Machines Corporation Interface Kit Page 3 P N 70 019 01 tte EXTRON ELECTRONICS EXTRON ELECTRONICS EUROPE EXTRON ELECTRONICS ASIA 79 11 Zs 1230 South Lewis Street Beeldschermweg 6C 41B Kreta Ayer Road Anaheim CA 92805 3821 AH Amersfoort Singapore 089003 68 116 01 runo 714 491 1500 FAX 714 491 1517 31 33 453 4040 FAX 31 33 453 4050 65 226 0015 FAX 65 226 0019 Rev C U S A The Netherlands Singapore www camboard de Tel 07131 911201 ce info camboard de Fax 07131 911203 _ imVertrieb von Installation of IBM 3482 3487 Interface Kit The IBM 3482 3487 Infowindow II kit consists of 68 116 01 Installation Instructions 26 357 01 MBC IBM 3482 87 Cable 880108 Adapter Assembly 26 364 01 MBC RGB Buffer w Blue Enhance NOTE Please verify that 6 items below are included in the Adapter assembly Qty Part Part Description Qty Part Part Description 1 3 990077 Mounting Plate Retainer 4 4 40 077 01 Thumbnut 3 8 x 0 25 ht 2 2 990076 Module Retainer 5 3 40 077 02 Thumbnut 3 8 x 0 2 ht 3 1 990075 Module Mounting Plate 6 6 40 005 01 4 Hex Nut Blue Hela SE Stand Installing the IBM 3482 3487 Infowindow II Kit 1 Disconnect all cables and the power cord 2 Turn the display module upside down so that it sits on its top with the scree
3. n facing you as shown in Figure 2 Pinch the blue latch within the tilt swivel stand and pull up the edge of the stand from the display module 3 Remove the logic module from the display module by pinching the plastic latch on the logic module toward the rear of the display see Figure 3 Gently pull up and lift out the logic module 4 Insert a mounting plate retainer Item 1 in Figure 1 into each of the three logic module retainer holes in the display unit as shown in Figure 4 www cambeard de ton IBM 3482 3487 Interface Kit e User s Eek Page 1 nse AMBOARD El amp ttthics 5 Place the module mounting plate on the Module Mounting display module as shown in Figure 5 lining it up so that the mounting hardware of the mounting plate retainer is fed through the proper holes Tighten down with three 3 8 x 0 2 thumbnuts Figure 1 item 5 6 Position the MBC Interface Cable so the cable exits toward the right side of the display unit See Figure 6 Plug the MBC cable into the card edge receptacle in the display unit The card edge receptacle normally receives the logic module 7 Plug the logic module into the MBC connector of the interface cable The plastic L shaped retainers of the logic module should slide into the positioning holes of the retaining plate See Figure 7 8 Place a module retainer Figure 1 item 2 MBC IBM 3482 3487 over the logic module one
4. on each side by Interface Cable sliding it over the mounting hardware as 26 357 01 shown in Figure 8 Tighten down the module T7 retainers with four 3 8 x 0 25 thumbnuts Figure 1 item 4 Reattach the tilt swivel stand to the bottom q of the terminal as shown in Figure 2 Return the terminal to its normal operating position as shown in Figure 9 eee This completes the mechanical assembly of N Figure 3 f the Infowindow II kit Connection of the MBC Interface cable to the MBC RGB Buffer is covered on Page 3 Module Aetaine cs Logic Modula Comal Module dodule Edge Mounting Plate Thumbnuts cS 4 Positioning prem Figure amp Holes 4 Interface a ye P Cable Z e c 071 31 91 1 204 e IBM 3482 3487 Interface Kit ueSPaipfe eamboard de Page 2 Fax 07131 911203
Download Pdf Manuals
Related Search