5”" OPERATING INSTRUCTIONS
Contents
1. 6 Malfunction and Troubleshooting If there is a failure during operation the charger will stop charging or discharging a warning code will be shown on the LCD the buzzer will sound see table below for possible reasons EERi E input voltage is more than 27V or less than 9 5V choose the correct voltage range sere Internal temperature is more than 100 C Let the charger coo down l Check the battery and connections to see if short circuit EER3 Battery shor circuit or open circuit or open circuit EER4 Wrong battery number Reset the number Reversed battery Connect with correct polarity 7 Contents 1 x battery charger 1x charge cable with Tamiya plug 1 x charge cable with crocodile clips 4 x operating instructions 8 Safety instructions 1 Read operating instructions carefully before use 1 Do not expose the battery charger to rain damp or hot conditions 1 When not in use disconnect the battery from the charger and the charger from the mains Do not charge hot batteries Batteries must be at ambient temperature before charging Only charge fast chargeable batteries Charging is oniy allowed after a previous discharge Do not leave the charger unattended during operation Immediately disconnect the battery from the charger if excessive heating occurs Explosion and chemical danger At a cell temperature of more than 45 the battery must be considered 100 charged Charge only coo batteries Charge2. During charge of batteries near to full capacity it is norma for the charging current to go down thus allowing the battery to be charged gradually The charger will detect a full battery either when the end charge voltage fora 2V battery is 2 5V a 6V battery is 7 5V a 12V battery is 15V and a24V battery is 30V or the temperature battery probe is more than 45 C or when the current is less than 80mA or the safety time is more than 20 hours The LED LEAD ACID will tum off the 4 bars in the battery symbol of the LCD display are continuously on and the charger wil begin to trickle charge the battery After disconnection of the battery from the charger the charged capacity value of the battery BATTERY CAPACITY will be reset to zero Beware Always disconnect the battery from the charge cable first and then disconnect the cables from the charger danger of short circuit Always set the charger to the correct battery chemistry before connecting the battery 5 Technical data EXPERT PRO EVO MODEL 60500 Input voltage 230V 50Hz OR 12 24 V BC Input current AC 1 2A DC max 154 1 16 Cells NiCd NiMH 4 2 19 2V DC 4 3 6742 Cells Lead Acid 2 6 12124V DC Battery capacity Approx 100 mAh 20 000 mAh Charge current approx 0 4 max 5000 mA Discharge current 1 8 cells 2A 9 16 celis 1A fixed Discharge voltage Approx 0 9V Cell 230x132x165 mm 1 8Kg 2 3 A Q gt 2 Q Dimensions weight
3. is designed to charge NiCd NiMH battery packs with 1 to 16 celis 1 2 19 2 V DC or lead acid cells with 1 3 6 or 12 cells 2 6 42 24 V DC Charge termination of NiCd NiMH cells is by the delta Peak method and is temperature supervised Charge contro for tead acid batteries is by current and voltage regulation NiCd NiMH batteries can be discharged with a current of approx 1A Charging current is adjustable from appr 0 1A to 5A The charger can be powered from 230 V 50Hz mains supply or 12 24V DC motor vehicle battery 3 Technical index 42 24V nominal Less than 9 5V or more than 27V intemal temperature and More than sorc fanstatus Lessthan 40 C Charging switches to trickle Battery temperature sense More than 45 C charge state ee E 0 1 4A at 15 amp 16 cells Discharge voltage is 0 9V 7 0V per cell DC input voltage range Charging Current Adjustment NiCd NiMH amp 24V SLA batteries to safe the vehicles fuse N Cd NEMH discharge Discharge ready 4 OPERATION Connect the charger to a 230 V 50Hz mains supply or to 12 24 V DC car battery 230V operation Plug the mains plug into a suitable socket and switch the battery charger on at the power switch position Make sure that the DC input crocodile clips are not short circuit His can affect bad operation in damage of the charger 42 24V operation Attach the battery charger directly to the car battery using the ext
4. only NiCd NiMH or lead acid batteries No LIION batteries or primary cells Explosion and chemical danger Only connect the battery charger to suitable voltage sources 230V 50 Hz OR 12 24V DC motor vehicle batteries Never both at the same time Do not short circuit the DC input clips Do not open equipment or carry out repairs Authorized personnel may only carry out repairs Mains switch 2 is only in AC mode under function Do not cover equipment or obstruct ventilation otherwise it may over heat Do not expose to direct sunlight l Do not charge more than one battery pack simultaneously Charge only cells of ihe same type and capacity as a battery pack Keep batteries battery charger and cables away from combustible materiais Avoid sparking as there maybe gases present from the batteries Never place the charger inside the engine compartment Keep leads away from moving parts Technical details subject wilhout prior notice No liability assumed for typographical errors 05 2004 4
5. CARSON EXPERT PRO EVO TYPE 60500 A MODEL SPORT T General information Congratulations on your purchase of the microcontroller charge station EXPERT PRO EVO from the CARSON range To ensure trouble free operation please read the instructions carefully before use 1 FRONT PANEL 9 SNS m e 9 kwh CHARGING CURRENT ADJUST SWITCH adjusts the level of charging current AC POWER SWIFCH Mains ON OFF switch BATTERY TYPE SELECT SWITCH selects type of battery N Cd N MH or LEAD ACID to be charged MAINS POWER FUSE HOLDER Fuse T3A DC INPUT CLIPS for 12 24V DC input BUZZER sounds at various stages during charge LED INDICATORS OF POWER AND CHARGE TEMPERATUR SENSOR For sensing the battery temperature AC INPUT PLUG For mains supply 40 CHARGER OUTPUT TERMINALS 14 12 14 OPERATING INSTRUCTIONS 230V AC 12 IN De Deha Peak DISCHARGE SELECT discharge battery number selector FUNCTION STATE INDICATORS BATTERY SELECT indicator of selecting battery number CHARGING CURRENT indicator of charge current BATTERY CAPACITY indicatar of battery capacity BATTERY VOLTAGE indicator of battery voltage DISCHARGE CURRENT indicator of discharge current DISCHARGE VOLTAGE indicator of discharge voltage DISCHARGE CAPACITY indicator of discharge capacity DISPLAY BUTTON CONFIRN to view the display and confirm LCD DISPLAY 2 Product description The EXPERT PRO EVO
6. ension cable with crocodile clips supplied Pay attention to correct polarity red black In the 12 VDC mode the power switch is not used The green power LED lights and the buzzer sounds for a second The LCD display should read AUTO using the battery type selectswitch 3 select the correct battery type NiCd NiMH or Lead Acid Turn the charging current adjust switch 1 to minimum fully anti clockwise Connect one of the two enclosed charge cables to the output jacks Pay attention to correct polarity black to black far negative red to red for positive Attach the magnetic temperature sensor of the battery charger to the battery body Connect the charge cable correctly to the battery red positive black negative In the AUTO state after selecting the battery type you can press the DISPLAY BUTTON CONFIRM for approx 2 seconds to start the charge process The charger will identify the number of connected cells and start to charge The NiCd NiMH charge indicator lights red If youwish to select the number of cells manually press the DISCHARGE SELECT 11 button a number of times to set the number of cells according to the battery pack that is connected The number of cells will be shown in the LCD display Then press and hoid the DISPLAY CONFIRM 13 button for 2 seconds to begin charging During the charge process the bars in the battery symbol light from right to left to indicate the charging process The operati
7. ng mode on the LCD display can be selected using the DISPLAY CONFIRM 13 button By pressing this button once the mode of the LCD display changes from BATTERY SELECT to CHARGING CURRENT in this mode the charge current should be selected between 0 1A and SA using the CHARGING CURRENT ADJUST SWITCH Caution Take note of the maximum permitted charging current from the battery oe manufacturer if this value is not stated we recommend a maximum of 1 C e g a 3 Ah battery pack should be charged with a maximum of 3A charging current Press the DISPLAY CONFIRM 13 button once more and the display switches to BATTERY CAPACITY and the charged capacity can be seen in miliamps per hour mAh Press the DISPLAY CONFIRM button again and the LCD display changes to the BATTERY VOLTAGE mode which displays the voltage of the connected battery pack in DC Volts Once the charging process has been completed either by DELTA PEAK maximum battery temperature recognition gt 45 C by Vmax or the safety timer 40h the colour of the LED NiCd NiMH changes from red to green the buzzer gives a beep 3 times and the 4 bars in the battery symbol of the LCD display will be continuously on The battery is now fully charged and provided with a trickle charge Pressing the DISPLAY CONFIRM 13 button with the battery connected will show BATTERY SELECTION CHARGING CURRENT BATTERY CAPACITY and BATTERY VOLTAGE Alter disconnecting the ba
8. ttery from the charger or if the discharge mode is selected the charged capacity value of the battery BATTERY CAPACITY will be reset to zero During charge or trickle charge you can choose to discharge the battery by pressing the DISCHARGE SELECT 11 button for 2 seconds to start to discharge the NiCd MiMH LED lights yellow and the discharge function begins The LED flashes yellow at the end of discharge function and the battery capacity will be shown In the discharge mode you can view the discharged battery capacity the discharge current and the battery voltage During discharging or at the end of discharging if the DISCHARGE SELECT 11 button is pressed for 2 seconds the chargerwil automatically begin to charge If charging Lead Batteries LEAD ACID set the battery type selector switch NICD NiMH LEAD ACID to the LEAD ACID position You can now set the charger in AUTO mode or adjust the nominal voltage of the battery to be charged with the DISCHARGE SELECT button Connect the charge cable correctly to the battery red positive black negative Press the DISPLAY CONFIRM button to start the charge process and the LED LEAD ACID lights red The bar display in the battery symbol flashes from right to left The operating state of the LCD display can be selected by pressing the DISPLAY CONFIRM 13 button switch as described previously Caution Take note of charge currents recommended by the battery manufacturer
Download Pdf Manuals
Related Search