USER'S GUIDE - JBL Professional
Contents
1. AUDIO INPUTS The EON 206P has 6 inputs 2 mono inputs and 2 stereo inputs All of the inputs will route to the speakers and to the MONITOR OUTPUT SECTION MONO MIC LINE INPUTS Moving from left to right there are 2 identical input strips comprised of from top to bottom a treble control bass control reverb control reverb on off button volume control mic line selector and a XLR 1 4 combination conector Treble control adjusts the amount of high frequencies on the particular channel Bass control adjusts the amount of low fequencies on the particular channel Effect control adjusts the amount of effect on the particular channel 3 Channel Volume control adjusts the gain on the particular channel MIC LINE SELECTOR allows you to select between a microphone XLR input and a line 1 4 phone input Combination 1 4 phone plug and XLR male input CH5 6 MONTOR STEREO INPUTS The EON 206P has two stereo inputs and these are used primarily for MP3 or CD players but could be used with the stereo output of an electronic keyboard instrument pre amp or processor or an electronic drum machine The inputs labeled CH 3 4 offer the option of using 1 4 phone plugs or RCA plugs and this channel has a volume control The input labeled CH 5 6 is a 3 5 mm stereo input of the type typically found on personal music players This input does not have a volume control as personal music players usua2. EON 0OGP PORTABLE PA USER S GUIDE For Francais Deutsch Espa ol visit www jblpro com Contents Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Section 8 Important Safety Instructions Precautions Declaration of Conformity Introduction To The EON 206P PA System System Specifications Cables and Connectors Contact Information Warranty Information 12 13 14 15 S ection 1 Important Safety Instructions R N N O A 10 11 12 13 14 16 17 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenien
3. FCC Compliance Notice This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio and television reception which can be determined by turning the equipment off and on the user is encouraged to try to collect the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e C
4. 19 The mains plug of the power supply cord shall remain readily operable Care and Cleaning EON 206P systems may be cleaned with a dry cloth Do not get moisture into any of the openings in the system Ensure that the system is unplugged from the AC outlet before cleaning THIS APPARATUS CONTAINS POTENTIALLY LETHAL VOLTAGES TO PREVENT ELECTRIC SHOCK OR HAZARD DO NOT REMOVE CHASSIS MIXER MODULE OR AC INPUT COVERS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Section 2 Precautions The EON 206P PA system covered by this manual is not intended for use in high moisture environments Moisture can damage the speaker cone and surround and cause corrosion of electrical contacts and metal parts Avoid exposing the speakers to direct moisture Keep speakers out of extended or intense direct sunlight The driver suspension will prematurely dry out and finished surfaces may be degraded by long term exposure to intense ultra violet UV light The EON 206P PA system can generate considerable energy When placed on a slippery surface such as polished wood or linoleum the speaker may move due to its acoustical energy output Precautions should be taken to assure that the speaker does not fall off a stage or table on which it is placed Stand Mounting Safety Precautions The EON 206P speakers contain a 36 mm receptacle cup to allow mounting on tripod stands or on a pole over subwoofers When using stands o
5. its transportation and for payment of any initial shipping charges However we will pay the return shipping charges if repairs are covered by the warranty Limitation of Implied Warranties ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY EXCLUSION OF CERTAIN DAMAGES JBL S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT AT OUR OPTION OF ANY DEFECTIVE PRODUCT AND SHALL NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 15 UBL by HARMAN Part Number 5001426
6. ay 8 00am 5 00pm Pacific Coast Time in the U S A 800 8JBLPRO 800 852 5776 www jblproservice com On The World Wide Web www jblpro com Professional Contacts Outside the USA Contact the JBL Professional Distributor in your area A complete list of JBL Professional international distributors is provided at our U S A website www jblpro com Product Registration Register your product online at www jblpro com Section 8 Warranty Information The JBL Limited Warranty on professional loudspeaker products except for enclosures remains in effect for five years from the date of the first consumer purchase JBL amplifiers are warranted for three years from the date of original purchase Enclosures and all other JBL products are warranted for two years from the date of original purchase Who Is Protected By This Warranty Your JBL Warranty protects the original owner and all subsequent owners so long as A Your JBL product has been purchased in the Continental United States Hawaii or Alaska This Warranty does not apply to JBL products purchased elsewhere except for purchases by military outlets Other purchasers should contact the local JBL distributor for warranty information and B The original dated bill of sale is presented whenever warranty service is required What Does The JBL Warranty Cover Except as specified below your JBL Warranty covers all defects in material and workmanship The following are not cover
7. ce receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Service Instruction in Owner s Manual CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO To completely disconnect this apparatus from the AC mains disconnect the power supply cord plug from the AC receptacle WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE 18 Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids such as vases are placed on the equipment
8. ed Damage caused by accident misuse abuse product modification or neglect damage occurring during shipment damage resulting from failure to follow instructions contained in your Instruction Manual damage resulting from the performance of repairs by someone not authorized by JBL claims based upon any misrepresentations by the seller any JBL product on which the serial number has been defaced modified or removed Who Pays For What JBL will pay all labor and material expenses for all repairs covered by this warranty Please be sure to save the original shipping cartons because a charge will be made if replacement cartons are requested Payment of shipping charges is discussed in the next section of this warranty How To Obtain Warranty Performance If your JBL product ever needs service write or telephone us at JBL Incorporated Attn Customer Service Department 8500 Balboa Boulevard PO Box 2200 Northridge California 91329 818 893 8411 We may direct you to an authorized JBL Service Agency or ask you to send your unit to the factory for repair Either way you ll need to present the original bill of sale to establish the date of purchase Please do not ship your JBL product to the factory without prior authorization If transportation of your JBL product presents any unusual difficulties please advise us and we may make special arrangements with you Otherwise you are responsible for transporting your product for repair or arranging for
9. ese jacks to the jacks on the back of the speakers To Left speaker To Right speaker 5 Connecting the AC Power Cable Connect the female end of the power cable to the mixer and plug the male end into the wall socket or extension cord Turn the MASTER VOLUME control to 0 Now turn the power switch to the on position You should see the POWER indicator illuminated At this point you are ready to bring in an audio signal and hear the signal amplified by the system AC power inlet Getting Acquainted with the EON 206P Powered Mixer This part of the EON 206P system houses the mixing board and power amplifier You will connect all of the microphones musical instruments external sound sources like MP3 or CD players in addition to any recording devices or additional speakers like a personal monitor subwoofer or Front of House feed The Basics The mixing board is actually a very simple device A mixing board brings audio sources in through the inputs and routes the signal to the outputs MASTER VOLUME SPEAKER OUTPUTS or MONITOR OUTPUTS The mixer controls enable the user to affect the tone and or volume in addition to routing the signal and adding reverb to individual input sources CH3 4 CH5 6 MONITOR OUT Let s look at the inputs first
10. l in professional audio systems Microphone to mixer For connecting balanced devices with 1 4 inch phone and maybe used interchangeably For connections of instruments with unbalanced outputs to balanced XLR inputs This cable is electrically identical to TRS unbalanced 1 4 inch phone and may be used interchangeably Connects consumer audio products and some DJ mixer outputs to professional audio equipment inputs Splits a stereo output into separate left right signals Change to a TRS mini phone jack to connect to the output of a portable MP3 CD player and computer sound cards to a mixer Only with balanced in and outputs 1 r lt 5 rss ss o m Shield 2 Q 2 3 Q 0 3 Tip 1 shield Ring 2 Sleeve 3 Tip 1 shield Ring 2 Sleeve 3 u 9S 2 Sleeve 3 2 3 Sleeve shield Tip gt gt gt gt gt n TIP Sleeve O Sleeve shield Tip r Tip O Sleeve shield Ring Sleeve Tip Sleeve shield O 1 no connection o wn wna 13 Section 7 Contact Information JBL by HARMAN Mailing Address JBL Professional 8500 Balboa Blvd Northridge CA 91329 Shipping Address JBL Professional 8500 Balboa Blvd Dock 15 Northridge CA 91329 Do not return product to this address without first obtaining prior authorization from JBL Customer Service Monday through Frid
11. lly have a volume control built into the unit This is the best way to control the volume of the unit plugged into this input Volume Control for STEREO IN 3 4 VOLUME Stereo in 3 4 RCA inputs use with MP3 Player CD or any consumer type electronics O 3 5 mm input jack for CH 5 6 for use with personal music players CH 3 4 CH 5 6 Stereo in 3 4 1 4 Phone inputs use with electronic keyboard instrument pre amp or processor or an electronic drum machine 10 STEREO OUTPUTS We ve brought signals into the mixer now let s send them somewhere The EON 206P has Left and Right 1 4 outputs 1 LEFT RIGHT speaker outputs These outputs should only be connected to the EON 206P speakers and under no condition should they be connected to the input of another electronic device L These outputs carry power and as such could damage the electronic device Only use unshielded speaker cables R like the cables provided with your EON 206P 2 MONITOR OUTPUTS These outputs allow you to route the stereo mixer signal to another destination like a recording device personal monitor subwoofer or to another PA system Front of House MASTER VOLUME and Limit LED Your EON 206P is equipped with a Master Volume that controls the overall output volume of the system and a Yellow LED that indicates that you have approached the ma
12. n to avoid prolonged exposure to SPL in excess of 90 dB WATCH FOR THESE SYMBOLS The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating i ici i i i i TRIC S and maintenance Servicing instructions in the literature AN ZN accompanying the product WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated Dangerous Voltage within the products enclusure that may be of sufficient magnitude to constitute a risk of electric shock to persons Section 3 EON 206P PA System Declaration of Conformity This equipment complies with the EMC directive 89 336 EEC Modified by 92 31 EEC 93 68 EEC 98 13 EEC and LVD 73 23 EEC modified by 93 68 EEC This product meets safety standards EN60065 2002 UL6500 7th Edition 2003 UL 60065 STANDARD FOR AUDIO VIDEO AND SIMILAR ELECTRONIC APPARATUS SAFETY EQUIREMENTS Edition 7 Revision Date 2007 12 11 CSA C22 2 NO 60065 03 AUDIO VIDEO AND SIMILAR ELECTRONIC APPARATUS SAFETY REQUIREMENTS Edition 1 Revision Date 2006 04 01 IEC 60065 AUDIO VIDEO AND SIMILAR ELECTRONIC APPARATUS SAFETY REQUIREMENTS Edition 7 1 Issue Date 2005 12 01 And EMC Standards EN55103 1 E2 EN55103 2 E2
13. ols center detent 12 dB cut and boost On Board DSP Limiting and Tuning 1 x JBL 326G 165 mm 6 5 in woofer 1 neodymium black mylar dome tweeter 100 x 80 nominal 2 2 kHz Passive network 2nd order filters 12 dB per octave for high pass and low pass filters Polypropylene 36 mm pole socket One on top Powder coated perforated steel 20 9 X 27 8 x 13 4 530mm x 705mm x 340mm 11 38 kg 25 Ibs Section 6 Cables and Connectors XLR F to XLR M Microphone Cable TRS balanced 1 4 inch phone jack to XLR M TRS unbalanced 1 4 inch phone jack to XLR M TS unbalanced 1 4 inch phone jack to XLR M XLR M to RCA phono cable TRS 1 4 inch Phone jack to dual 1 4 inch Phone jack TRS 1 4 inch Phone jack to dual 1 4 inch Phone jack XLR F to XLR M audio ground lift XLR F to XLR M Microphone Cable mm E TRS Balanced 1 4 Phone to XLR M Cable E Tip Ring Sleeve TRS Unbalanced 1 4 Phone to XLR M Cable r 9 GE Tip Ring Sleeve TS Unbalanced 1 4 Phone to XLR M Cable Tip Sleeve XLR M to RCA phono Cable TS Unbalanced 1 4 Phone to RCA phono Cable i TRS 1 4 Phone to dual TS 1 4 Phone XLT F to XLR M Audio Groud Lift e E gt o V SLEEVE T V SLEEVE TP The standard cable for interconnection of microphone and line level signa
14. onsult the dealer or an experienced radio TV technician for help Section 4 Introduction To The EON 206P PA System Thank you for choosing the JBL EON 206P PA system The EON 206P is a self contained portable PA system featuring multiple input channels with individual tone controls reverb and convenient output routing capabilities that allow the user to integrate the system into any number of audio environments And with its lightweight and ergonomic design the EON 206P is perfect for situations where ease and portability are just as important as quality and flexibility Included in the EON 206P package are e 2 JBL professional speakers e 1 center housing with powered mixer and compartment for storage of speaker cables e 1 pair of unshielded speaker cables 1 power cable e User s guide GETTING STARTED 1 Remove EON 206P system from the carton 2 Detach speakers from center powered mixer section 1 2 3 Press here Slide button Lift 3 If you have purchased speaker stands you can ill place the speakers on the stands utilizing the pole mount adaptor built into the EON206P speaker cabinets gt 4 Connect the Mixer Module to the Speakers On the back side of the mixer you will notice two 4 phone jacks these are your speaker output jacks Take the speaker cables and connect them from th
15. r poles be sure to observe the following precautions e Check the stand or pole specification to be certain the device is designed to support the weight of the speaker Observe all safety precautions specified by the manufacturer Always verify that the stand or subwoofer pole is placed on a flat level and stable surface and be sure to fully extend the legs of tripod type stands Position the stand so that the legs do not present a trip hazard e Route cables so that performers production crew and audience will not trip and topple the speakers over e Inspect the stand or pole and associated hardware before each use and do not use equipment with worn damaged or missing parts Do not attempt to place more than one EON 206P series speaker on a stand or pole e Always be cautious in windy outdoor conditions It may be necessary to place additional weight i e sandbags on the base of the stand to improve stability Avoid attaching banners or similar items to any part of a speaker system Such attachments could act as a sail and topple the system e Unless you are confident that you can handle the weight of the speaker ask another person to help you get it onto the tripod stand or pole Hearing Damage Prolonged Exposure To Excessive SPL The EON 206P system is capable of generating sound pressure levels SPL sufficient to cause permanent hearing damage to performers production crew and audience members Caution should be take
16. ximum output MONITOR OUT MASTER VOLUME 11 Section 5 System Specifications EON206P System Amplifier Mixer Speaker System Type Maximum SPL Output Frequency Range 10dB Frequency Response 3dB AC input Design System Power Rating Output Connector Input Connectors Channels Input Impedance Output Connectors Signal Indicators EQ System Limiter LF Driver HF Driver Coverage Pattern Crossover Frequency Crossover Type Enclosure Suspension Mounting Handles Grille Shipping Package Dimensions H x W x D Net Weight of System Powered mixer with 2 two way bass reflex enclosures 113 dB peak system output pink noise 64Hz 22kHz 77Hz 20kHz 100 120 VAC 220 240 VAC 50 60 Hz Class D 160 Watts 2 x 80 W 2 x 1 4 TS unbalanced amplifier outputs 6 inputs 2 Mono Mic Line 2 x Stereo 1 2 are XLR 1 4 jack combo connectors XLR is a mic level input 1 4 is a line level input 3 4 one pair of 1 4 balanced TRS jacks stereo and a pair of RCA jacks stereo 5 6 is a 3 5 mm stereo jack Ch 1 2 Combo XLR 40 K Ohms Balanced Ch 1 2 Combo TRS 40 K Ohms Balanced Ch 3 4 TRS 20 K Ohms Balanced Ch 3 4 RCA 5 K Ohms Unbalanced Ch 5 6 3 5 mm 10 K Ohms Unbalanced Monitor outputs one pair of RCA jacks stereo Limit Yellow LED indicates limiter active condition Individual channel Bass and Treble contr
Download Pdf Manuals
Related Search