Operating instructions
Contents
1. and store the selection using M OK Clean waste water pump see above If necessary start programmes Close the door Wait for programme stop buzzer sounding 5 times Open supply fitting Lay supply hose without kinks 1 Unscrew water connection 2 Clean filter in the water connection 3 Flow rate must be min 9 l min when the water inlet is open If the flow rate is less replace the supply fitting Follow manufacturer s specifications detergent Discoloration is quite safe fades after subsequent rinse cycles Fault Dishes not clean Sand or grainy residues on dishes Stains and streaks Milky residues on dishes can be removed Milky film glasses cloudy dull cannot be removed Cutlery rusty Possible Cause Utensils are situated too close to each other or on top of each other Too little cleaning product Unsuitable programme selected Spray nozzles blocked Filters dirty not installed securely Spray arms blocked Rinse aid dosage too high too low Water softening system incorrectly set no special salt Glasses not dishwasher proof Cutlery not rust proof Hard knife blades are more susceptible Extraneous rust Remedy Spread out the utensils avoid contact between the utensils Follow manufacturer s specifications detergent Select more intensive programme Clean spray arms see above Clean the strainers see above Arrange the utensils so th2. insert the spray head as illustrated in the diagram ES J d lz IE Long items serving cutlery salad servers N W gt or knives should be placed on the shelf so N that they do not obstruct the rotation of the eee 999 spray arms The shelf can be folded back MN ml when not requi quired for use u Am i Small accessories holder To ensure that the spray jet can reach all SOME modes parts arrange the baking sheets as Light weight plastic accessories e g CUPS illustrated lids etc can be held securely in the small max 4 baking sheets and 2 grilles accessories holder SS a en Adjusting position of basket Top basket with side levers not on all models Rackmatic Pull out the top basket SS Y max 20 25cm ee max 20 25cm 81cm 86cm AAA A If required the height of the top basket can be adjusted in order to create more space To lower the basket press in for large utensils either in the top or bottom succession the two levers on the left basket and right sides of the basket Always Select one of the two following procedures take hold of the side of the basket on according to the design of the top
3. Empty the dishwasher according to the following steps Turn on the tap Switch on the appliance Start any automatic programme and close the appliance door Wait until approx 4 minutes have elapsed Then open the door terminate the programme and close the door to drain the appliance Wait until the buzzer is emitted 5 times i e all the water has been drained Switch off the appliance Turn off the tap Secure loose parts prior to transportation Transport the appliance upright only Otherwise residual water may penetrate the control and damage the appliance Protection from freezing temperatures If the appliance is installed in a location where there is a risk of freezing temperatures e g in a holiday home all water must be completely drained out of the interior see Transporting the dishwasher Turn OFF the tap disconnect the supply hose and allow to drain 35 en Subjekt to modification Before first use E The display gives optical character information on the programmes Select the display language see instruction manual options and settings as well as actions available Fill in salt and rinse aid see below Set Softening System see instruction manual rl lt AutoWash_ gt Se Main switch Switch on the device This dishwasher is equipped with touch buttons Menu OK Select options store changed value A gentle touch starts th
4. Ensure that the fresh water connection is not kinked crushed or twisted When replacing the appliance always connect a new water supply hose to the water supply The old supply hose must not be re used Water pressure Minimum 0 05 MPa 0 5 bar maximum 1 MPa 10 bar If the water pressure Is higher install a pressure reducing valve Flow rate Minimum of 10 litres per minute Water temperature We recommend that you use cold water If you do use hot water the temperature should not exceed 60 C Electrical connection Connect the appliance only to 230 V alternating current via a correctly installed socket with protective conductor See rating plate for required fusing 33 The socket must be attached near the dishwasher and be freely accessible The connection may be modified by an electrician only Use only a residual current operated circuit breaker which features the symbol Only this circuit breaker guarantees compliance with the currently valid regulations en Removing the appliance It is essential when removing the appliance to observe the following sequence First disconnect the appliance from the power supply Pull out the mains plug Turn off the water supply Disconnect the waste water and fresh water connections Loosen the fastening screws under the worktop If fitted remove the base panel Pull out the appliance carefully pulling the hose behind Transportation
5. Salt content in washing water is too high Lid on salt container is not screwed tight Too much salt was spilt while filling container 32 Glasses become clouded and discoloured coating cannot be wiped off Unsuitable detergent was used Glasses are not dishwasher proof Smears left behind on glasses and cutlery glasses have acquired a metallic appearance Amount of rinse aid set too high serve Home The dishwasher cannot be operated via serve Home The device is not connected to the network The device is not ready for serve Home The System Interface is not installed Customer Service Please call your local service agent if you are not able to resolve any problem yourself The name of your nearest service agent is shown in the Customer Service address list When you call please provide details of the model number 1 and the production FD number 2 which are shown on the nameplate on the appliance door Please note that a visit by the customer service technician in the event of a fault or one of the problems previously discussed is not free of charge even during the warranty period en Notes Disposal of your old appliance Old appliances are not worthless rubbish Valuable raw materials can be reclaimed by recycling old appliances Pull out the mains plug of the redundant appliance Cut off the power cord and discard with mains plug To
6. as cups glasses pots pans etc are stood upside down curved items or those with recesses should be at a slant so that water can run off they are stacked securely and cannot tip over they do not prevent the spray arms from rotating while washing takes place Very small items should not be washed in the dishwasher as they could easily fall out of the baskets Removing the dishes To prevent water dripping from the top basket onto the dishes in the lower basket we recommend that you empty the lower basket first and then the top basket Cups and glasses Upper basket 20 on applicable models 12 Pots and pans Lower basket 28 Cutlery Cutlery should be placed in the dishwasher always unsorted and with the eating surface pointing downwards The spray jet is then better able to reach the individual parts To prevent injuries place long pointed accessories and knives on the tag re some models or on the knife shelf available as an accessory Folding spikes on applicable models To improve stacking of pots and pans the spikes can be folded down en Baking sheet spray head Shelf some models not on all models You can clean large baking sheets or Lean tall glasses and those with long grilles with the baking sheet spray head stems against the shelf not against other To do this remove the top basket and items to be washed
7. basket the upper edge otherwise the basket for your appliance model will not drop smoothly and may Top basket with upper damage the utensils and lower roller pairs Pull out the top basket Remove the top basket and re attach it To raise the basket take hold of the basket on the upper edge and pull upwards Before you re insert the basket ensure that it is at the same height on both sides Otherwise the appliance door cannot be closed and the upper spray arm will not connect to the water circuit en Detergents Notes on detergents You may use any brand of liquid or powder detergent as well as tablets that have been specifically designed for use in domestic dishwashers do not use normal washing up liquid Nowadays there are three types of dishwasher detergent available 1 Those containing phosphates and chlorine 2 Those containing phosphates but no chlorine 3 Those containing neither phosphates nor chlorine When a phosphate free detergent is used in conjunction with hard water there is a greater possibility that white marks will be left behind on the dishes and glasses etc These can be prevented by pouring an increased amount of detergent into the dispenser Chlorine free detergents have a reduced bleaching effect This may mean that tea stains are not completely removed or plastic items become discoloured This can be resolved by using the Auto Su
8. etc Too many items in the rack Items in the rack were touching each other Not enough detergent was added to dispenser Selected wash programme was not intensive enough Rotation of spray arm was obstructed by dish etc Nozzles in spray arm are blocked by remnants of food Filters are blocked Filters have been incorrectly fitted Waste water pump is jammed 31 en O Plastic items are discoloured 0 Not enough detergent was added to dispenser White stains are left on crockery glasses have a milky appearance Not enough detergent was added 0 to input compartment Amount of rinse aid was set too low Although water is quite hard no salt has been put in appliance Water softener was set too low Lid on salt container is not screwed tight f you used a phosphate free detergent try a detergent containing phosphates and compare results O Dishes cutlery etc have not been dried Selected programme did not include drying function Amount of rinse aid was set too low Items were removed from dishwasher too soon O Glasses have a dull appearance Amount of rinse aid was set too low O Tea stains or traces of lipstick have not been completely removed Detergent does not have a sufficient bleaching effect Washing temperature was set too low O Traces of rust on cutlery Cutlery is not sufficiently rustproof
9. regeneration cycle will only work if the salt is dissolved in water After switching on the device lack of salt is indicated by the display Refill Salt This display will no longer appear once you have set the softening system to the value Open the screw type cap of the compartment 25 Before operating the device for the first time you must pour 1 litre of water into the salt compartment Then you must refill salt not table salt using the supplied salt filling aid until the salt compartment is full max 1 5 kg When you refill the salt water is being displaced and drains off Therefore the refilling must take place shortly before switching on the device In order to avoid corrosion This way the overflowing salt solution is diluted and flushed immediately Then clean the filling area of salt residues and screw the compartment lid back on without tilting the lid As soon as a Sufficiently high salt solution has formed the display Refill Salt will disappear If you do not want to wait until the display disappears but you want to wash immediately confirm the refilling of the salt using the button M OK 2 If you do not want to refill the salt now you can skip the display Refill Salt by pressing the button M OK 2 A Do not pour detergent into the container for special salt This would destroy the water softener Setting up the water softene
10. seconds Ifthe door is not opened the appliance automatically switches off after one hour During this time the acoustic signal sounds every 15 minutes After letting the device cool down take out the dishes When the programme has finished you can switch off the appliance or start it again AN Note For an optimum drying of the dishes wait for 15 minutes after the programme has finished before you open the door and empty the dishwasher During this time the possibly remaining water on the dishes can evaporate and condense on the sides of the device s interior AN Note If the device becomes disconnected from the power supply during operation e g it is switched off or there is a power cut all settings remain stored Operation will resume automatically once the power supply has been restored 27 en Maintenance and care You can help prevent faults by checking and maintaining your appliance regularly This will save time and reduce problems Therefore you should occasionally examine the inside of your dishwasher Overall condition of the appliance Check the rinsing compartment for grease and limescale deposits If you find any deposits Fill the detergent dispenser with detergent Start the empty appliance with the programme which has the highest rinsing temperature Clean the door seal Wipe the door seal regularly with a damp cloth and remove any deposits Special Salt When the
11. the device offers you greater comfort and mobility at home as well as on the road In order for your dishwasher to become serve Home capable you will need a special accessory the System Interface You can purchase this interface from your specialist supplier The interface must be mounted in the chamber at the front of the dishwasher following the installation instructions supplied with the system interface When you select your dishwasher s mode Remote Control On you can remotely control the device You can set up and start the prepared switched on and closed dishwasher if you are not at home Equally you can switch off your dishwasher at any time even if the device is not in the Remote Control Mode o Bedieneinheit SA z B Webpad e KH lt gt xs Status Inquiry You can check the current status of your dishwasher at any time Remote Control The serve Home system allows you to select the programme and to start the dishwasher To take advantage of this service you must set the dishwasher s mode to Remote Control On Advice and Warning Messages These messages can be transmitted from your dishwasher to your operating unit Remote Diagnosis You can transmit error messages to the Customer Support thereby helping in the diagnosis Adjusting the appliance Switching on the appliance Turn on the tap fully Switch on the appliance with the main switch 1 and if requi
12. 20 2 20 2 20 appliance automatically switches off after 5 seconds 4 Buzzer volume Energy Consumption kWh 1 05 1 05 105 5 Amount of rinse aid added 9000 005 142 8202 416 Water Consumption litres Strainers Check if required clean Spray arms Remove blockages deposits Rotate filter cylinder remove filter system Pull lower arm upwards rinse under flowing water Insert perhaps with toothpick Clean spray nozzles under flowing water Screw in filter system NOTE MARK Insert lower arm With some models Ladle out water and remove filters Unscrew cover Torx T20 Check area of fan impeller for foreign objects Screw in cover and insert filters Fault Display in wrong language Residual water in the device Programme does not start does not run on Device does not work stops Plastic parts parts of dishes discoloured Possible Cause Language changed Waste water pump blocked Programme has not been started Door was opened before end of programme Supply fitting not open Supply hose kinked Supply fitting jammed or calcified Sv Too little cleaning product Discoloration caused by food colourings gt tomato sauce Remedy Switch off and on the device Press the button M OK repeatedly until the display shows the language selection Select the language using
13. 9000 026 701 8402 Operating instructions Dish washer IGV 699 Kuppersbusch ALLERFEINSTE KUCHENTECHNIK Ss A AA a a er ania A ad U O Y A en Index Safety instructions 4 Opening and closing the door 17 Getting to Know your appliance 6 serve Home 000 18 Before using your appliance Adjusting the appliance 19 for the first time 4 AMO SIN soccer arias 19 Filling in the Salt 8 Programme overview 21 Setting up the water softener 9 Selecting options standard settings 22 Filling with rinse aid 10 Maintenance and care 28 Unsuitable dishes 11 Fault finding 30 Arranging crockery glasses Customer Service 33 etc inthe dishwasher 12 Notes soeoea coser den dare sopor 33 Detergents o oooooo 15 Installation 34 en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit Do not use a damaged appliance but consult your supplier Please dispose of packaging material properly The corrugated cardboard consists mainly of waste paper The polystyrene moulded parts have been foamed without any CFCs The polyethylene film PE consists partly of secondary raw material The wooden frames if fitted are made of re
14. By pressing buttons or 3 you can select a set value between 0 and 6 To switch off select position 0 Press button M OK 2 The set value is Saved and you are returned to the Start menu If the set value O is selected rinse aid is not dispensed Low rinse aid is_not displayed 20 Switching Add special salt and therefore the water softening system off and on Switch on the appliance with the main switch 1 Keep pressing button M OK 2 until the hardness auto setting is displayed By pressing buttons or 3 select a set value between 0 off and 7 The factory setting is hardness auto To switch off select position O Press button M OK 2 The set value is saved and you are returned to the Start menu If the set value 0 off is selected the water softening system is switched off Low salt is not displayed AN Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products ensure that the rinse aid dispenser amount has been switched on and the water softening system has been set to the correct water hardness or to hardness auto en Programme overview Type of utensil e g porcelain pans mara Fragile cutlery wearing glasses etc Type of food remains e g Soups sou
15. anew If the option Remote Options is selected the message Enrol Device will be ee By pressing the button you enrol the device again at de gateway After successfully enrolling the device the message Auto Wash will be displayed If the enrolment is unsuccessful the display shows no gateway found Only with installed interface Aqua sensor on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water A light barrier can detect dissolved food remnants in the water e g egg fat and oats The Aqua sensor is used according to the programme When the Aqua sensor is active clean rinsing water may be transferred into the next rinsing bath and or the temperature adjusted If the turbidity is greater the water is drained and is replaced with fresh water In this way the water consumption is reduced by approx 4 litres for utensils which are less dirty Optical indicator during operation With some models During the rinse programme a light point appears on the floor below the device s door Only open the dishwasher door when the light point has disappeared In the case of built in dishwashers with flush front the light point will not be visible 26 Start programme Before starting check again whether the spray arms can move freely Press the button Start 5 Menu The message Close
16. ard settings Operating principle From the Main Menu you can select the following options settings by repeatedly pressing the button M OK 2 Time Pre select Remote Control Reduce Time Drying Level Buzzer Volume Adding Rinse Aid Water Hardness Language Standard Programmes Remote Setting Only with installed serve Home interface Within an option basic setting there are several possible settings that can be selected using the buttons or 3 A selected setting is applied by changing to the next option basic setting using the button M OK 2 If a setting has been changed using the buttons or and stored using M OK 2 the message Value stored will be displayed and the display returns to the Main Menu Time Pre select You can delay the programme start by 24 hours in steps of 30 minutes If the option Time Pre select is chosen the display shows Delay Start 00 mins Set the desired time Return to the Main Menu by pressing M OK 2 and start the required programme by pressing the Start Button 5 Close the door This starts the time counting backwards When the set time has elapsed the programme will start automatically Until the programme starts you are able to change the set time and programme To do this use the button 3 to return to the Main Menu and change the settings Then
17. at the spray arms can rotate freely Streaks Reduce dosage Water or limescale stains Increase dosage Set water softening system correctly Refill with special salt Use dishwasher proof glasses Use glass friendly cleaning products Use dishwasher proof cutlery Never wash rusting parts in the appliance Further advice can be found in the instruction manual Open the door Open the door and press the Terminate programme button To continue the programme close the door Close the door and wait until the buzzer is emitted 5 times Arrange dishwasher proof utensils having removed any ash wax grease or ink Coarsely remove sticky labels large remnants of jam milk products or food according to the operating instructions Restart the programme or switch off the appliance and check that the spray arms can rotate freely
18. ave been left in the water can cause a blockage in the pump The water is no longer pumped out of the dishwasher and it can be seen covering the filter Proceed as follows Ladle out as much water as possible Remove the filters 26 Undo the screw in the cover Torx T 20 and remove the cover Inspect the inside and remove any obstructions that you find Re insert the cover and screw down Re insert the filters and screw down 29 en Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that arise during normal daily usage yourself without having to call out a service engineer Not only does this save costs but it also means that the appliance is available for use again that much sooner The following list of common occurrences and their remedies should help you identify the causes of most problems Problems On Switching On Wrong Language Selected The following steps return you to the language selection 1 Switch off the device 2 Switch on the device Press the button M OK 2 repeatedly until the language selection appears in the display 3 Select the language and confirm your selection O The device does not start A fuse in the house is defect The device is not properly plugged in The device s door is not closed properly The device s door was closed without first starting the pr
19. d patterns aluminium and silver parts tend to become discoloured and fade during the rinsing cycle Even some types of glass e g crystal glass objects may become cloudy after many rinse cycles Completely absorbent materials such as sponges and cloths must not be cleaned in the dishwasher either Recommendation In future buy only dishes which are identified as dishwasher safe AN Note Dishes which are soiled with ash wax lubricating grease or ink must not be cleaned in the dishwasher en Damage to glassware and other dishes Possible causes type of glass or manufacturing process chemical composition of detergent water temperature and duration of dishwasher programme Suggested remedy Use glassware or porcelain dishes that have been marked dishwasher proof by the manufacturer Use a mild detergent that is described as kind to dishes If necessary seek further information from detergent manufacturers Select a programme with as low a temperature and as short a duration as possible To prevent damage take glass and cutlery out of the dishwasher as soon as possible after the programme has ended 11 en Arranging crockery glasses etc in the dishwasher Loading the dishwasher Scrape off any large amounts of left over food It is not necessary to rinse the dishes under running water Place objects in the dishwasher in such a way that items such
20. e aid refill indicator switched off see auto 3in1 chapter Salt refill indicator switched off see auto 3in1 chapter At the end of the programme there is still water in the appliance The waste water hose is blocked or kinked The waste water pump is blocked The filters are blocked The programme has not yet ended Wait until the programme ends or terminate the programme during washing Unusual amount of foam is created Normal washing up liquid has been poured into the rinse aid container Remove any spilled rinse aid with a Cloth as it could otherwise lead to excessive foaming during the next washing cycle en Appliance stops suddenly while washing is taking place Cut in electricity supply to appliance Water supply has been interrupted Knocking sound can be heard while washing is taking place A spray arm is knocking against the dishes inside the appliance Rattling sound can be heard while washing is taking place Crockery has not been stacked properly inside the appliance Knocking sound coming from inlet valves This is caused by the way the water pipes have been laid and it has no effect upon the way the appliance functions There is no remedy for this With the dishes cutlery etc O Remnants of food are stuck to the dishes cutlery etc Dishwasher was not loaded properly Jets of water could not reach all parts of the dishes
21. e function and Select programmes and settings Start Start programme The luminous arrows indicate whether you are able to select among other options using or Unscrew Only before using Pour in max Screw on the the lid the dishwasher 1 5 kg 3 Ib 5 oz lid Switch on for the first time salt never deter dishwasher pour approx 11 immediately 1 1 4 pt water into the salt opening Press the _ marking gt Lift the Quick Guide Dishwasher Warning Pour in the Push the lid cleaning agent too press combination PLOP products are not suitable for all programmes follow manufac turer s instructions Switch on by pressing main switch approx 2 seconds Programme Overview Auto Super Auto Wash Delicate Wash Se lt AutoWash gt Ser PC Duration hs mins 1 40 2 20 1 40 2 40 1 20 1 50 0 30 according to European Standard EN 50242 Energy Consumption kWh 1 20 1 60 1 00 1 30 0 80 1 10 0 80 0 10 The programme data are laboratory read outs In practice deviations are possible Water Consumption litres 16 23 12 20 10 17 10 A Press Start button 6 Water Hardness 1 Time Pre select Open the door when the buzzer has sounded 5 times 2 Reduce time 7 Language GET EN hemin programme stop Ready is briefly displayed the 3 Drying level 8 Standard programmes 215 2
22. e rinse programme is automatically adjusted in order to obtain the best possible rinsing and drying result Observe the following important information if using combined cleaning products Regeneration salt is not required up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l only No other settings on the appliance are required Salt is still required if the water hardness is above 21 dH 37 fH 26 Clarke 3 7 mmol l Fill the salt dispenser with salt 25 The factory set hardness setting hardness auto ensures that the water softening system is set optimally by the optical limescale sensor even if combined cleaning products are used en If in doubt please contact the detergent manufacturer especially if the utensils are very wet at the end of the programme limescale forms AN Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of salt and rinse aid Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness If the Add rinse aid or special salt display is defective you can switch it off as follows Switching Add rinse aid off and on Switch on the appliance with the main switch 1 Keep pressing button M OK 2 until the rinse aid 4 setting is displayed
23. el indicator at the compartment not being illuminated when the door is fully opened and by the display Refill Rinse Aid no longer being lit Close the lid of the compartment until it audibly clicks into place If necessary the filling aid will be re inserted automatically If you want to fill in the rinse aid at a later time you can skip the display Refill Rinse Aid by pressing the button M OK 2 If necessary you can change the amount of rinse aid that is added during the operation In order to do this select the option Rinse Aid Amount as described in the chapter Device Set up under the heading Options Basic Settings rinse aid control Fill when door is fully open Filling when the door is half open AN Note Use only rinse aid for domestic dishwashers Spilt rinse aid may result in excessive foam formation in the next rinse cycle Therefore remove any spilt rinse aid with a cloth Unsuitable dishes You should not clean the following items in your dishwasher Cutlery and dishes made of wood They will leach out and become unsightly the utilised adhesives are also not suitable for the dishwasher temperatures Delicate d cor glasses craft dishes and vases special antique or irreplaceable dishes These d cor items are not dishwasher safe Plastic parts copper and tin dishes sensitive to hot water are not suitable either Overglaze
24. ffl s sauces potatoes pastries rice eggs fried food Soups potatoes pastries fried food rice eggs Coffee cake milk sausage cold drinks salads Rinse if the utensils have been left for several days prior to wash ing in the dish washer Amount of Large gt small Very i a small food remains m Condition of Very food remains adhesive Slightly adhesive vv 4 Wash AUTO WASH AUTO QUICK PRERINSE programme DELICATE WASH ONLY WASH 45 55 Programme progress 35 45 45 The programme progress is optimised and adjusted according to the appliance load and degree of soiling Intermedi on the utensils te was Final wash 21 en Programme data The programme data duration energy and water consumption can be found in the summary of instructions and refers to standard conditions Greater deviations may be caused by different quantities of utensils inlet temperature of the water water pressure ambient temperature mains voltage tolerances and appliance specific tolerances e g temperature water flow rate etc Only ranges can be indicated for the automatic programmes The water consumption values refer to water hardness value 4 22 Selecting options stand
25. fully utilised by short programmes It is recommended to use washing powder for these programmes For the Auto Super Wash function pour an additional 10 15 ml of detergent onto the inside of the appliance door ht at Reduce costs If your dishes are only moderately dirty you may be able to use less detergent than recommended If using washing tablets please refer to the washing tablets box where to place the tablets in the appliance e g in the cutlery basket detergent dispenser Close the detergent dispenser Slide the dispenser cover completely over the detergent compartment 1 and then press down firmly 2 until the catch clicks into position Close the detergent dispenser when the door is completely open Close the detergent dispenser when the door is half open During the washing cycle the cover of the detergent dispenser is automatically opened and the detergent is washed out The cover is therefore open when the programme ends en Opening and closing the door To open the door pull the door handle To close the door press the door shut until it clicks into position The door can be easily opened before the wash programme starts and when the programme ends en serve Home on applicable models This dishwasher is serve Home capable serve Home is a network comprising other serve Home domestic appliances besides dishwashers Through it
26. guage en Standard Programmes In addition to the rinse programmes available in the Main Menu you can choose among the following standard programmes from the programme Normal Extra Eco Normal Plus Set the desired programme and start the selected programme by pressing the Start Button 5 If you do not want to use any of the displayed standard programmes return to the Main Menu by using the button M OK 2 f you want to cancel the selection of a standard programme in the Main Menu press the button Back The selected standard programme will be displayed By pressing the buttons or the Main Menu will display the programme Auto Wash Normal Type of Dishes Mixed Dishes Amount of Food Particles Little to Many State of l l Food Particles Lightly Adhesive You can find the corresponding programme data length of time energy and water consumption in the short manual We recommend on principle to use the Auto Programmes because they keep the water and energy consumption as low as possible due to the variable programme run In the case of the standard programmes on the other hand the programme run is predetermined 29 en Remote Options The dishwasher installs itself automatically during the first use within a serve Home network In some cases however it might become necessary to start the enrolment process
27. gulations 34 Installation The dishwasher must be connected by a qualified technician to ensure correct operation The specifications for supply drainage and connected load must fulfil the required criteria as stated in the following paragraphs or in the installation instructions Install the appliance in the following sequence Check the delivery Install the appliance Connect the waste water Connect the fresh water Connect the power supply Delivery Your dishwasher was checked at the factory to ensure that it was in perfect working order This may have left some small water stains in the dishwasher These will disappear after the first rinse cycle Installation The required installation dimensions can be found in the installation instructions Using the height adjustable feet adjust the appliance until it is level Ensure that the appliance is standing firmly Waste water connection See the installation instructions for the required connection steps If required attach a siphon with drainage spigot Using the enclosed parts connect the waste water hose to the drainage spigot of the siphon Ensure that the drainage hose is not kinked crushed or twisted ensure that there is no sealing cover which prevents the waster water from flowing away Fresh water connection Using the enclosed parts connect the fresh water connection to the tap according to the installation instructions
28. if required and rinse aid Press the button M OK 2 until Hardness Auto is displayed Using the buttons or 3 select the setting corresponding to the hardness of your mains water The factory setting is Hardness Auto Press the button M OK 2 to store the setting and return to the Main Menu If the setting is 0 the softening system is switched off Possible lack of salt will not be indicated Ill IV 10 42 stos lisis 222 505 2950 Water hardness fh 0 6 7 11 12 16 17 21 22 29 30 397 38 54 955 89 Clarke 0 4 58 9 11 12 1154 620 221 26 422 28 29 62 mmol l Set on the appliance 5 020 65 reap epee ee 302950 od 555580 en Filling with rinse aid Rinse aid is used in washing mode to ensure that glasses are sparkling and utensils are stain free When the appliance is switched on low rinse aid level is indicated by Refill rinse aid You can add rinse aid either when the appliance door is completely open or for a more comfortable posture when the door is half open Open the rinse aid dispenser 30 by pressing the button on the dispenser cover and open the cover When the door is half open also pull out the hinged filling aid until it locks into position tia f VIME Fill in the rinse aid slowly and take care not to overfill The right amount is indicated by the lev
29. language The following steps will take you back to the language selection 1 Switch off the device 2 Switch on the device Press the button M OK 2 until the language selection is displayed 3 Select the desired language and confirm your selection JE onure gt Providing operating materials To operate the dishwasher you will require salt only for appropriate water hardness see chapter Adjusting the softening system rinse aid detergent Only use products which are suitable for the dishwasher Before using the appliance for the first time and after selecting the language fill with salt if required and rinse aid and adjust the softening system Proceed as described in the chapters Filling with salt Filling with rinse aid and Adjusting the softening system en Filling in the Salt A Note Ifthe hardness of your mains water corresponds to the device s index value Ej see chapter Setting up the softening system you do not need to fill in the salt because the operation will not use any salt In case of the settings Hardness Auto and to Y salt must be filled in During the rinse cycle the salt is being washed automatically from the salt compartment into the softening system where it will dissolve the lime The lime containing solution drains from the dishwasher Afterwards the softening system is ready to be loaded again This
30. le the door hinge area should be covered at the side Risk of injury Covers are available as optional accessories from customer services or specialist stores In daily use AN Warning Knives and other utensils with sharp points must be placed in the baskets either flat or with the points downwards Use the dishwasher only in the household and only for its designed purpose i e for washing domestic dishes Do not lean or sit on the open door The appliance could tip The water in the appliance is not drinking water Do not add any solvents to the washing chamber Danger of explosion Open the door carefully when the programme is still running Water could spray out of the appliance Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Children in the household Do not let infants play or operate the dishwasher Keep cleaning and rinsing agents out of the reach of infants Keep infants away from the open dishwasher It could contain residue of the cleaning agent en A aa To prevent injuries e g caused by stumbling open the dishwasher only briefly in order to load and unload the dishwasher If a fault occurs Repairs or other work on the dishwasher should only be carried out by a qualified specialist The dishwasher must be disconnected from the electricity supply before any repairs or other work a
31. o interrupt do not in any circumstance press the button 3 Cancel Programme because this will not allow the programme to continue To continue the programme close the door The programme will continue automatically Inthe case of a warm water supply or when the appliance is already heated leave the door slightly ajar for a few minutes before closing it Otherwise the door can spring open again due to the warm air trapped in the device s interior Cancelling active programme Open the door First open the door only slightly in order to avoid water spraying out The message Cancel Programme will be displayed alternating with the message Close the door the remaining programme time the selected programme and the current programme phase In order to cancel the programme press 3 Cancel Programme The display shows To drain Close the door with the message Close the door flashing en Close the door The water remaining in the device s interior will be pumped off Once the pumping off has finished a buzzer will sound 5 times Open the door Ready is briefly displayed the appliance automatically switches off after 5 seconds End of the programme As soon as the programme has finished a buzzer will sound 5 times Open the door Ready is briefly displayed the appliance automatically switches off after 5
32. o select among other options using or 3 This dishwasher is equipped with touch buttons A gentle touch starts the function Always keep the user interface clean and free of grease in order to prevent malfunctions Use a dry or lightly moistened cloth only do not use scouring or abrasive detergents Appliance interior 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Upper utensils basket Additional cutlery basket for the top basket Additional cup rack Upper spray arm Lower spray arm Dispenser for salt Filters Cutlery basket Lower utensils basket Lock Dispenser for rinse aid with refill display Detergent dispenser Optical limescale sensor Rating plate some models en Before using your appliance for the first time Before you can use your appliance for the first time you must select the language When the appliance has been switched on the following display is output The language abbreviation DE for Deutsch German is flashing If you want to select a different language press or 3 repeatedly until the abbreviation of your desired language flashes Confirm the language selection by pressing M OK 2 All following optical character messages will be displayed in the selected language Chosen the wrong
33. ogramme 30 O Some time after the programme start a continuous acoustic signal sounds The device does not draw water When the door is opened the message Check water supply is displayed Mains water tap is not opened Open the tap fully and press the button M OK 2 of the device Then close the device s door for the programme to resume Filter of the water inlet hose is blocked Switch off the device and disconnect it from the power supply Close the mains water tap Clean the filter located at the connection of the Aquastop or the inlet hose Finally restore the power supply Open the mains water tap switch on the device and close the door for the programme to resume AN Attention Please remember Repairs may only be carried out by professionals Unprofessional repairs can cause significant damage and danger to the user With the appliance itself Lower spray arm rotates with difficulty Spray arm is blocked by small items or food remains Lid in detergent compartment cannot be closed Detergent compartment has been overfilled Mechanism is clogged with remnants of detergent Indicator lamps do not extinguish after washing has finished Remnants of detergent stuck inside dispenser Compartment was damp when it was filled up with detergent Compartment must be dry before detergent is added Refill display does not light up Rins
34. per Wash programme increasing the amount of detergent using a detergent that contains chloride Check the label on the packaging to determine whether a particular product is Suitable for use with silverware If you have any further questions we recommend that you contact the customer advice departments of the respective detergent manufacturer en Detergent dispenser with dosing aid The graduated detergent dispenser helps you add the correct amount of detergent The lower and middle lines in the dispenser indicate15 ml and 25 ml of detergent respectively The dispenser can be filled with 40 ml of detergent when the door is opened horizontally Filling with detergent You can add detergent either when the appliance door is completely open or for a more comfortable posture when the door is half open Ifthe detergent dispenser is still closed open it by pressing the catch Y When the door is half open press the button on the right side of the detergent dispenser Swivel up the detergent compartment and cover The detergent compartment can easily be locked into position by lifting it slightly Pour detergent into the dispenser Please follow the manufacturer s instructions on the detergent packet for correct dosage Due to the different solvency properties of the detergent tablets supplied by various manufacturers the cleaning efficiency of the detergent may not be
35. prevent children from locking themselves in the appliance and suffocating destroy the door lock and childproof lock if fitted You received your new appliance in a protective shipping carton All packaging materials are environmentally friendly and recyclable Please contribute to a better environment by disposing of packaging materials in an environmentally friendly manner Please ask your dealer or inquire at your local authority about current means of disposal Keep children away from the shipping carton and packaging components Danger of suffocation from folding cartons and plastic film Notes on comparison tests You will find details of the conditions for the comparison tests on the additional Notes on comparison tests sheet The consumption values for the relevant programmes are given in the introduction 33 en General Built under and integrated appliances which are subsequently installed as free standing appliances must be secured to prevent them from falling over e g by screwing them to the wall or by installing them under a continuous worktop which is screwed to the adjoining units For Swiss version only The appliance can be installed without difficulty between wooden and plastic walls in a kitchen range If the appliance is not connected via a plug the installation side must feature an all pole disconnector with a contact gap of at least 3 mm in order to satisfy the relevant safety re
36. r In order to provide satisfactory rinsing results the dishwasher requires soft water i e containing little or no lime otherwise water stains will be left behind on the dishes and interior containers If the tap water exceeds a certain level of hardness it must be softened i e decalcified so that it can be used in the dishwasher This is achieved by adding a special salt to the water softener inside the dishwasher The water softener that is the required amount of salt is set up according to how hard the tap water is The softening system is only capable to accept a limited amount of lime If this limit is reached the system must be regenerated or refreshed using salt The factory setting Hardness Auto allows the deposit sensor to determine the hardness and to control the softening system automatically This means that changes to the settings are unnecessary during start up or in case of changes in the water hardness Water hardness range o Water hardness dh 9 3 46 7 9 en If you would nevertheless like to set the water softening system manually proceed as follows Find out the degree of hardness of your tap water Your water supply company or customer service will assist you Switch on the appliance with the main switch 1 The main menu is displayed if switching on the appliance for the first time only when a language has been selected and dispensers have been filled with salt
37. re started Pull the mains plug out of the wall socket or switch off at the fuse box Grasp the plug to remove it from the socket do not tug on the cable Turn the water off at the tap When disposing of old appliances Appliances that have reached the end of their service life should be rendered inoperable in order to exclude the possibility of subsequent accidents Pull the mains plug out of the wall socket cut through the connecting cable and disable the door lock Take the appliance to a designated waste disposal centre AN Warning Children could get locked in the appliance risk of suffocation or get stuck in other positions Therefore Remove the mains plug cut the mains wire and set aside Damage the door lock so that the door can no longer be closed en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front Individual positions are referred to in the text Control panel 1 ch Main switch 2 Button M OK Select options store changed value 3 Buttons and Select programmes and settings 4 This display gives optical character information on the programmes options and settings to be selected as well as on the available actions 5 lt gt Start Button Start programme 6 Door Opener The luminous arrows indicate whether you are able t
38. red top up with salt and rinse aid see chapters Filling 13 with salt Filling with rinse aid The main menu is then displayed lt Auto Wash gt After switching on the Main Menu shows the programme Auto Wash Setting the Programme From the programme Auto Wash in the Main Menu you can select among the following programmes Auto Super Wash Auto Wash Auto Delicate Wash Short Rinse Prerinse Only Set the desired programme by using the buttons or 3 The auto programmes Auto Super Wash Auto Wash and Auto Delicate Wash automatically match the programme to the amount and soil level of the dishes This keeps the energy and water consumption as low as possible Using the following programme overview you can select the appropriate programme for the type amount and soil level of the dishes en auto 3in1 The use of so called combined detergent products may make the use of rinse aid and or salt unnecessary There are currently several types of combined detergent products available 3in1 They contain detergent rinse aid and salt function 2in1 They contain detergent and rinse aid or salt function gt gt gt Always check the type of detergent or combined product which you are using Always follow the operating instructions or the information on the packaging Th
39. salt level is low your dishwasher displays a message in the window Rinse aid When the rinse aid level is low your dishwasher displays a message in the window Filters The filters 26 prevent larger remnants of food or other objects from getting inside the pump This residue can occasionally clog up the filters The filter system consists of a filter cylinder a flat fine filter and depending on the model a microfilter Inspect the filters for obstructions every time the dishwasher has been used By unscrewing the filter cylinder you can remove the filter system Remove any food remnants and clean the filters under running water O 28 Reassembly Insert the filter system and screw down with the filter cylinder Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 23 and 24 and the arm mountings Inspect the nozzles in the spray arms for blocked holes due to remnants of food If necessary pull the lower arm 24 upwards and lift it off Unscrew the upper spray arm 23 Clean both spray arms under running water Refit the spray arms Ensure that the lower arm has locked into place and the upper one is screwed tight Spray arms en Pump on applicable models Larger remnants of food that have not been trapped by the filters and h
40. sidual wood and are untreated The hoops if fitted consist of polypropylene PP Installation Install and connect the appliance according to the installation and assembly instructions The dishwasher must NOT be connected to the power supply during installation Ensure that the protective conductor system of the domestic electricity supply has been installed correctly Electrical connection conditions must correspond with the specifications on the rating plate of the dishwasher In order for your dishwasher to become serve Home capable you will need a special accessory the System Interface available from your specialist supplier Please follow the enclosed installation instructions and install the system interface in the chamber located at the front of the dishwasher Built under and built in appliances should always be installed under a continuous work surface which is attached to the adjacent cupboards in order to ensure that the appliance is entirely stable After the appliance has been installed the mains plug should still be easily accessible Not on all models The plastic housing on the water input contains an electrically operated valve The connecting wires are inside the inlet hose Do not cut through this hose and do not immerse the plastic housing in water AN Warning For safety reasons if the appliance is not fitted in a recess thereby making a side wall accessib
41. start the programme again In order to delete the pre selected time set the time back to Delay Start 00mins Remote Control After choosing the option Remote Control the display will show Remote Control Off factory setting You activate this option by selecting Remote Control On Only with installed interface en Reduce Time The Auto Programmes allow you to reduce the run time of the programmes However in order to achieve an optimal cleaning result the water and energy consumption will be increased If the option Reduce Time is chosen the display shows Reduce Time Off factory setting Select Reduce Time On Return to the Main Menu by pressing M OK 2 and start the required programme by pressing the Start Button 5 If you do not want to use Reduce Time the next time you use the dishwasher you must deselect this option Drying Level Ifthe option Drying Level is chosen the display shows Normal Drying factory setting Alternatively you can choose Save Drying or Extra Drying The option Extra Drying increases the temperature during rinsing in all programmes Please take care with delicate dishes Buzzer Volume You can modify the volume of the acoustic signals or even turn it off altogether Ifthe option B
42. the door will be displayed alternating with a display of the expected programme time This time is only approximate At programme start it corresponds to the time the programme ran the last time During the programme run the remaining time will be adjusted according to the water supply temperature and the amount and soil level of the dishes If you have chosen a time for the programme start the message Close Door will appear when the programme is started alternating with the pre selected time Close the door The programme or the pre selected time respectively will run The programme and other settings can still be changed as long as the door is still open after pressing the button Start 5 By pressing the button M OK 2 Back return to the Main Menu where you can change the settings Finally start the programme again When the door is closed after the start and the programme has already started you will have to interrupt the programme in order to change any settings see Cancel Programme in the Main Cancel Programme In order to interrupt the programme open the door In order to avoid water escaping only open the door slightly first The message Cancel Programme will be displayed alternating with the message Close the door the remaining programme time the selected programme and the current programme phase In order t
43. uzzer Volume is chosen the display shows Buzzer 6 factory setting You can change this value to 0 acoustic signals switched off or to values between 1 quiet and 6 loud A short buzz demonstrates the currently chosen volume level 23 en Adding Rinse Aid You can set the amount of rinse aid added Ifthe option Adding Rinse Aid is chosen the display shows Rinse Aid 4 factory setting Change this setting only if there are streaks reduce the value or water stains increase the value remaining on the dishes You can choose a value between 0 and 6 Water Hardness The factory setting Hardness Auto allows the deposit sensor to determine the hardness and to control the softening system automatically This means that changes to the settings are unnecessary during start up or in case of changes in the water hardness 24 Language You can change the language selected when the appliance was started for the first time see chapter Before Starting The Device For The First Time If the option Language is chosen the display shows several language abbreviations The abbreviation of the currently selected language is flashing In order to choose a different language press or 3 until the desired language appears Confirm the language selection by pressing M OK 2 All subsequent optical character messages will be displayed in the selected lan
Download Pdf Manuals
Related Search