Digital Gear Display Operating Instructions
Contents
1. clamp 2x Cable ties 3x Data cable 3 metres 1x Sensor box 1x Sensor cable data cable short 1x CON DU DAU N e Fig 1 Instrument installation 1 1 1 The ignition should be switched off before instal lation When installing in a universal instrument carrier Attach instrument with threaded ring in the instrument carrier Connect the 3 metres long data cable 6 to one of the two rear sockets in the instrument fig 2 and guide the data cable carefully through the vehicle into the console below the gear boot Figure 2 1 1 2 Please read the respective assembly instructions when using the Indy Cator attachment set 1 1 2 Connection to the board grid Connect the plus line from the ignition and ground line to the power supply lines of the refe rence box 3 red to 12 Volt of the ignition black to ground you may use the included cable clamps find possible placement for reference box but do not glue on yet The reference box may still need to be moved when programming the gears 1 3 1 Sensor box assembly Connect the data cable 8 of the sensor box 7 to the reference box and the display instrument to the reference box fig 3 Figure 3 it is unimportant which one of the two sockets is used Firmly attach sensor box to the swit ching rod in a twist proof position using the included cable ties 1 3 2 Vehicles with reverse lock often have guide parts that can be moved in lon2. INDY CATOR DASH Digital Gear Display Operating Instructions GASLOCK Table of Contents Pa O cc bachacsrancseausdocwecsudecsetaseesdvecasescucace About INDY CATOR DASH RASE ctesecaaaeces Package content Pa SO a en dun des ee tin Instrument installation PASC Programming PAO O ss a as in Troubleshooting About INDY CATOR DASH First we would like to explain to vou the function of the digital gear display It works according to the principle of forming the difference between two position sensors As a result the selected transmission is displayed for you The electronic system recognises even the smallest changes of positions of the gear lever knob It works completely independently of the vehicle transmission Only if a position change is safely recognised as transmission change will the display change This may take 1 1 5 s This transmission display is to serve as an aid We assume no warranty for correctness of the display If the transmissions are not displayed correctly for some reason please repeat programming with the motor gear on operational temperature Depending on vehicle type and gear position extreme vehicle acceleration may lead to short term reading changes on the display This is based on the physical characteri stics of the sensors and does not constitute any malfunction Package content Display instrument 1x Threaded ring 1x Reference box with power supply lines 1x Cable terminal
3. ctive foil from the adhesive strips position reference box and press on firmly Verify that the gear lever is still set to idle Now acknowledge the box position by briefly pressing the push button 2 3 3 Gear programming now Starts Starting in first gear the display now shows all gears in sequen ce as flashing figures 2 3 4 Display please switch to first gear please switch to second gear please switch to third gear please switch to fourth gear please switch to fifth gear if the vehicle only has 4 gears ignore display and leave it in 4th gear please switch to sixth gear if the vehicle does not have any 6th gear ignore display and leave it in 5th or 4th gear please switch to reverse gear if there is no gear change the display change may take approx 30 S please switch back to first gear Now accelerate the vehicle in first gear start driving as normal Once the display recognises acceleration a running bar is displayed CR J VE After a few seconds the number of the active gear is displayed here it is the number 1 Your Indy Cator gear display is now programmed and ready for operation Please switch off the motor Programming remains saved with the display ignition switched off The gear boot and any applicable covers in the car can now be re assembled Troubleshooting If re programming is required press the button of the reference box until C is displayed an
4. d start again as described on page 6 If the previously selected colour is to be retained please confirm it with the button without moving the reference box again Display only shows running ring DEA Sensor box not connected Check cable connections VE Gears not programmed gt Programme gears Gears are not recognised displayed incorrectly Sensor casing loose Reference casing loose Re programme gears Display goes out when the headlights are switched on Po Ground cable black connected incorrectly Es Ground cable black to chassis 10 Display remains black Changing LCD display brightness Supply lines red and black must be checked If the supply lines are connected correctly e g to DASH G VOLT the reference box status lamp is lit green Fig 6 nes Foam E E Figure 6 Check data line between reference box and instrument Too many display instruments connected to one reference box Vehicle battery voltage too low
5. gitudinal direction around the actual gear lever Please verify that these guides have as little play as possible A moving sensor may lead to wrong gear recogni tion Ideal attachment would be right at the gear lever below the gear boot Fig 4 1 3 3 Switch on ignition briefly to check display or connections Reprogrammed display shows a rotating or running bar Figure 4 Figure 5 Programming 2 1 1 The vehicle should be placed on a surface that is as level as possible before programming Since the vehicle has to start in first gear after programming light acceleration please ensure now that there are no obstacles 20 metres straight on are sufficient and that traffic is not impaired 2 1 2 Start the engine gear lever set to idle 2 2 1 LCD Colour selection Colour change by position change ofthe refe rence box Keep the reference box button 3 pressed for approx 5 s until C is displayed then let go of the button Tilt the reference box forwards and backwards in your hand to start colour selection The colour changes in small nuances when the reference box position is adjusted slightly Briefly confirm desired colour by pressing the push button on the reference box once Display now indicates a transverse bar ND 2 3 1 Fastening the reference box The box should be placed as horizontally as pos sible in the area of the switching lever Labelling points up Fig 5 2 3 2 Remove prote
Download Pdf Manuals
Related Search