Shifter knob with digital gear display Operating Instructions
Contents
1. INDY CATOR Shifter knob with digital gear display Operating Instructions GASLOCK Table of Contents About INDY CATOR 7 LED Package content Gear lever knob installation Programming Troubleshooting About INDY CATOR 7LED First we would like to explain to you the function of the digital gear display It works according to the principle of forming the difference between two position sensors As a result the selected transmission is displayed for you The electronic system recognises even the smallest changes of positions of the gear lever knob It works completely independently of the vehicle transmission Only if a position change is safely recognised as a transmission change will the display change This may take 1 1 5 s This transmission display is to serve as an aid We assume no warranty for correctness of the display If the transmissions are not displayed correctly for some reason please repeat programming with the motor gear at operational temperature Depending on vehicle type and gear position extreme vehicle acceleration may lead to short term reading changes on the display This is based on the physical characteri stics of the sensors and does not constitute any malfunction Package content Gear lever knob with retention ring 1x Data cable 1x Reference box with power supply lines 4x Hexagon socket wrench 1x Grub screws long and short 2x one each Cable terminal cla2. mps 2x Cable ties 1x N OW BWN e Illustr 1 Gear lever knob installation 1 1 1 Disassembly of the original gear lever knob and gear boot Install LED gear lever knob and gear boot the data cable at the gear lever knob must not be damaged The gear boot can be placed between the gear lever knob and the retention ring to cover it or below the retention ring For this the retention ring can be pushed on in two different directions fig 2 and 3 with radius up or radius down 1 2 1 Connection reference box 3 Connect the plus line from the ignition and ground line to the power supply lines of the reference box Figure 2 Figure 3 red to ignition 12 Volt black to ground the included cable clamps can be used Find possible refe rence box position De grease this surface for gluing on the reference box 3 and clean it Con nect data cable between the LED gear lever knob and reference box 3 It is unimportant which one of the two sockets is used Fasten data cable to the gear lever with cable tie as Strain relief 1 2 2 Switch on ignition briefly to check display or connections Reprogrammed display shows a rotating or running bar Programming Programmes individual gear lever positions of your car for gear recognition and display 2 1 1 The vehicle should be placed on a surface that is as level as possible before programming Since the vehicle has to start in first gear afte
3. ng as normal Once the display recognises acceleration a run ning bar is displayed After a few seconds the number of the active gear is displayed here it is the number 1 Your Indy Cator gear display is now programmed and ready for operation Please switch off the motor Programming remains saved with the display ignition switched off The gear boot and any applicable covers in the car can now be re assembled Troubleshooting If re programming is required press the button of the reference box until C is displayed and start again as described on page 6 Display only shows running ringagain as described on page 6 re l Gears not programmed Programme gears Gears are not recognised displayed incorrectly Gear lever loose Reference casing loose Re programme gears Changing LED display brightness Too many display instruments con nected to one reference box Vehicle battery voltage too low
4. r programming light acceleration please ensure now that there are no obstacles 20 metres straight on are sufficient and that traffic is not impaired 2 2 1 Start the engine gear lever set to idle 2 3 1 Fastening the reference box The box should be placed as horizontally as pos sible in the area of the switching lever Labelling points up Fig 4 2 3 2 Remove protective foil from the adhesive strips position reference box and press on firmly Verify that the gear lever is still set to idle Now keep the reference box button 3 pressed approx 5 s until C is displayed then let go of the button Then press the button twice in quick succession to get to the programming mode Figure 4 2 3 3 Gear programming now Starts Starting in first gear the display now shows all gears in sequen ce as flashing figures 2 3 4 Display 1o please switch to first gear 20 please switch to second gear 3 ee please switch to third gear 4 please switch to fourth gear D e please switch to fifth gear if the vehicle only has 4 gears ignore display and leave it in 4th gear 6 please switch to sixth gear if the vehicle does not have any 6th gear ignore display and leave it in 5th or 4th gear foo please switch to reverse gear if there is no gear change the display change may take approx 30 S 1 please switch back to first gear Ao Now accelerate the vehicle in first gear start drivi
Download Pdf Manuals
Related Search