Operating Instructions
Contents
1. BIKE LO GGE R o L Operating Instructions 3 Bluetooth Erhaltlich im App Store www bikelogger de 4 260336 760016 gt www bikelogger de Intended Use The BikeLogger L is designed to capture the journey data of any bicycle with a hub dynamo Make sure your bicycle s safety is not affected in any way by the installation of the BikeLogger For professional installation we recommend you seek help from a specialist or your bicycle dealer Supplemental sheet with basic information Heat shrink tubing Micro flat plug shoes BikeLogger L eee Sea Installation Summary The BikeLogger L is designed for installation on your bicycle s lamp bracket but can also be mounted onto another location This is done by attaching the BikeLogger along the cable found between the hub dynamo and lamp To do this please take the following steps below Please read full instructions carefully before beginning installation Tools Required 1 2 5mm Allen key 2 Insulation strippers or scissors knife 3 Crimp plier or regular flat nose pliers 4 Hot air gun or lighter Optional e Busch amp M ller headlight bracket 474 DL or 475D e Extra cable when extension necessary e Soldering iron for cable extension e Wire cutters Installation Instructions 1 Using the wire cutters cut a section of the lamp cable extending from the hub dynamo to the headlight If possible level this with the headlight frame cu2. ed time and other parameters are diagrammed Anti Theft Alarm e Swipe the default screen leftward to navigate to the Anti Theft mode e The BikeLogger will now notify you of any movement of your wheel for approximately 30 minutes LED flashing sequence Eo __ Ready to connect Ss oe CF eady to connect Maintenance required Connected Maintenance required Red flashing If time not pre set please load your Smartphone s BikeLogger app Sufficient if App runs in background On start red LED means that energy buffer is charging When full blue LED is lighted shortly Technical Data e Power Supply hub dynamo e Operating Temperature 20 C e Power consumption 10 mW 60 C e Range up to 100 m open field e Socket suitable for B amp M headlight e Dimensions 23mm x 32mm x 40mm brackets two 4 5 5mm thick bars e Weight 20g that run parallel at a distance of 10 e Bluetooth Version 4 0 Bluetooth mm Smart e Bluetooth Profile Cycling Speed and Cadence CSCP Guarantee Warranty and Contact We are liable to all contractual partners for any defects according meso international GmbH to our legal regulations For guarantee please contact your BikeLogger Support BikeLogger dealer or send your item directly to our address see Markt 21 23 right please include your receipt and all billing attachments 09648 Mittweida Please ensure adequate postage The manufacturer reserves all rights for techn
3. ical modifications www bikelogger de support Important Notes Electronic devices may not be Apple and the Apple logo are trademarks of Apple Inc disposed with household registered in the U S and other countries App Store is a waste service mark of Apple Inc Please dispense the device at a Bluetooth is a registered trademark of Bluetooth SIG designated waste disposal C Inc All other trademarks are property of their respective owners This product is compliant with the Directives 93 42 EEC 1999 5 EC and 2011 65 EU The relevant Declaration of Conformity is available at http bikelogger de wp content uploads BikeLogger CE eng pdf CE Declaration of Conformity According to the guidelines 1999 5 EC radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity R amp TTE 2011 65 EC restriction of the use of certain hazardous substances in electrical and electronic equipment ROHS II 2002 96 EC waste electrical and electronic equipment WEEE The manufacturer hereby declares meso international GmbH Markt 21 23 09648 Mittweida under his sole responsibility that the products listed hereafter BikeLogger L Fahrradcomputer mit Bluetooth LE zur Montage am Lampenbugel BikeLogger C Fahrradcomputer mit Bluetooth LE zur Montage im Steuerrohr conforms with the essential requirements of the directives mentioned above The conformity assessment procedures acc
4. ording to appendix IV of 1999 5 EC where carried out with support of SGS Fimko Oy Sdriniementie 3 Helsinki Finnland Applied standards Radio spectrum matters ERM EN 300 328 V1 7 1 Data transmission equipment operating in the 2 4 GHz ISM band Electromagnetic compatibility EMC EN 301 489 1 V1 8 1 Common technical requirements EN 301 489 17 V1 3 x2 Specific requirements for 2 4 GHz broadband transmission Safety EN 60950 1 2006 A11 2009 A1 2010 A12 2011 Information technology equipment The documents required for inspection of responsible authorities are kept by the manufacturer at the address mentioned above Mittweida March 1 2013 Senmi Place date Dipl Math Christian Schwerin CEO head of development
5. rake or gear cables for easier handling Getting Started In order to initiate a connection between the BikeLogger and app please ensure enough energy is generated Turn the bicycle s wheel long enough to activate your LED light Connect your Smartphone 1 Install the BikeLogger app onto your smartphone This can be found on the App Store 2 Make sure your smartphone s Bluetooth is switched on 3 Give your front wheel a good spin to enable the BikeLogger The device has been activated once the LED lights up blue 4 Connect with your Bikelogger by selecting Preferences gt Pair BikeLogger in your app menu The default PIN is 0000 Calibration 1 Select the menu item Preferences gt Calibrate BikeLogger in your BikeLogger app 2 Follow the instructions provided in the app Features View your Journey e To view the default screen choose Start in your BikeLogger app or simply spin your front wheel e Please note the following indicators for displaying information during your active journey o Red needle active speed O Cadence o Orange needle average speed of o B Length of active journey active journey o total kilometre o Analogue clock active time O Bluetooth Status Blue o Digital display inside the analogue connected White no connection clock length of active journey O active outside temperature View historical Data e Select History in your BikeLogger app e Spe
6. tting the cable as close to its bracket as possible Please pay attention to the length of cable which requires cutting cable may have to be extended to accommodate for installation If lighting is originally connected via a coaxial cable instead of a two wire cable please see our additional notes on http bikelogger de manual bikelogger lI 2 Unravel the cable and remove insulation with your available tool 3 Twist the two pairs of exposed cable ends together correspondingly 4 Using the crimp plier or other pull the flat plug shoes over the twisted cable ends Ensure both sets of wire ends are securely inside these accessories Make sure these are very tightly connected with the cables 5 Pull the shrink tubing over the flat plug shoes and using a heat source hot air gun or lighter heat the tubing material so it contracts Attention please be aware of dangers of radiated heat Risk of injury 7 The two flat shoe plugs should now be securely connected and attached to the BikeLogger L 5 iy ECE G Polarity is not important Please note however for lamps with a battery or capacitator a fault with the BikeLogger app may occur If so simply reverse the polarity with the BikeLogger device ELOG S _ J 5 OBluetoy th 8 Attach the BikeLogger L onto the headlight bracket and tighten securely with the Allen key Briefly adjust or position your bicycle s b
Download Pdf Manuals
Related Search