Operating instructions - Nilfisk-Alto / Wap
Contents
1. continued gt 20 Original Instructions Es 4 1 3 Fuelling 4 2 Start the washer 4 2 1 Switching on the washer when it is connected to a water supply 4 2 2 Switching on the washer when it is connected to open tanks suction mode NOTE See chapter 8 3 for required quantity of water and water pressure WARNING Always shut off the engine and let it cool for at least two minutes before fuelling Avoid spilling fuel If you do spill fuel when fuelling do not start the engine before the spilled fuel has evaporated If the washer is on a trailer any fuel spills must be wiped up before the machine is started 1 Start the engine See the operating manual for the fuel engine 1 Before connecting the suction hose to the washer fill the hose with water 2 Start the washer 3 Unlock the spray gun and activate it POSEIDON PE DE In the case of poor water quality sand etc we recommend that a fine water filter is fitted in the water inlet Never expose the machine to an open flame Smoking is prohibited during fuelling Also read the operating manual for the fuel engine Note Never operate the machine in a closed room the exhaust fumes are dangerous Follow the safety instructions in chapter 1 2 Unlock the spray gun and activate it 3 Lock the safety catch even during short pauses Activate the spray gun several times at short intervals to vent the2. Pressure fluctuations In suction mode gt Lack of water gt Pump accessories partially frozen gt Water inlet hose is too long or its cross section too small gt Lack of water caused by blocked water filter gt Lack of water because max permissible suction height has not been heeded gt Water too hot gt Pump draws in air only possible in suction mode Open the tap Thaw machine and accessories Use prescribed size of water inlet hose Clean the water filter in the water connection never operate the machine without water filter mounted See chapter 4 2 2 See chapter 4 2 2 Check that the suction set is air tight Repeat aeration Excess pressure gt Engine s throttle control is defective accessory Give less gas contact Nilfisk ALTO Service Department The motor does not start gt Low fuel level gt Low oil level in engine gt The pump is blocked or frozen Open fuel cock fill with fuel Fill with oil Thaw machine contact Nilfisk ALTO Service Department 26 Original Instructions POSEIDON PE DE The motor stops gt Low oil level in engine e Fill with oil When a detergent injector is used gt Injector is dirty or suction hose is blocked gt Detergent tank is empty gt The lance is not set to low pressure gt Low fuel level e Clean Fill the detergent tank e Adjust the lance to low pressure e Open fu
3. A A A 22 Switching off the pressure washer s src 23 Disconnecting supply Ines been 23 Storing the cleaner frost free uu rrvrrrreoerrreooarreooonnoon 23 Maintenance plan ek 24 Maintenance work ave caves enneteivswesecevstndeccceyieemecteendendacdberead 24 ice Ge eeh Eed 26 Recycling the pressure washer essssessssrrersrrrnessrrrnrnsernnnnss 27 EI 27 elle Re EE 28 Declaration of Conformity ccccceceeeeeeeeeeeeeeeeeeeeetenaeeeeeaeeees 28 16 Original Instructions Symbols Before starting up your high pressure washer for the first time this instruction manual must be read through carefully Save the instructions for later use Safety instructions marked with this symbol must be observed to prevent danger to persons 1 Important safety notes Before using the high pressure washer be sure to also read the enclosed operating instructions and keep them within reach at all times The high pressure washer may only be used by persons instructed in its use and who have been expressly authorised to do so General Use of the high pressure washer is subject to the applicable local regulations In addition to the operating instructions and the binding accident prevention regulations in the country of use the generally recognised rules for safe working must also be observed Any method of use endangering the safety of persons or equipment is forbidden Before use Befo
4. Sehit Sk No 7 Umraniye Istanbul 34775 www nilfisk com tr UNITED KINGDOM Nilfisk ALTO Bowerbank Way Gilwilly Industrial Estate Penrith Cumbria GB CA11 9BQ www nilfisk alto co uk UNITED ARAB EMIRATES Nilfisk Advance Middle East Branch SAIF Zone P O Box 122298 Sharjah www nilfisk com USA Nilfisk Advance 14600 21st Ave North Plymouth MN 55447 3408 www nilfisk alto us VIETNAM Nilfisk Advance Co Ltd No 51 Doc Ngu Str Lieu Giai Ward Ba Dinh Dist Hanoi www nilfisk com
5. immediately and contact Nilfisk ALTO service department 4 The machine can be started by means of the starter rope if the battery has gone flat See manual from Yanmar N Detergent can be added by means of the detergent injector 1 Dilute detergent according to the manufacturer s instructions 2 Set the pressure to the lowest setting on the lance CAUTION Never allow detergent to dry on the surface to be cleaned as this may cause damage 22 Original Instructions 5 After using the washer 5 1 Stop the pressure washer Switching off POSEIDON DE ZB me 5 2 Disconnecting supply lines 5 3 Storing the washer frost protected 1 Shut the fuel cock 2 Remove the water hose from the washer 1 Store the pressure washer in a dry room without danger of frost IMPORTANT If the high pressure washer is stored in a room with temperatures around or below 0 C anti freeze should be drawn into the pump beforehand 1 Remove the water inlet hose from the washer 2 Remove the lance 3 Start the washer and stop it again after max one minute POSEIDON PE DE 1 Stop the engine 2 Close the tap 3 Operate the spray gun until the wasser is depressurized 4 Lock the safety catch 1 Stop the washer by moving the throttle lever to STOP position 2 Switch off the ignition by pushing the ON OFF button The light indicators will now tur
6. nilfisk com MEXICO Nilfisk Advance de Mexico S de R L de C V Agustin M Chavez 1 PB 004 Col Centro Ciudad Santa Fe C P 01210 M xico D F www nilfisk advance com mx NEW ZEALAND Nilfisk Advance NZ Ltd Danish House 6 Rockridge Avenue Penrose Auckland NZ 1135 www nilfisk com au NORWAY Nilfisk Advance AS Bjornerudvejen 24 Oslo N 1266 www nilfisk alto no POLAND Nilfisk Advance Sp z 0 0 Millenium Logistic Park ul 3 go Maja 8 Bud B4 Pruszk w PL 05 800 www nilfisk alto pl PORTUGAL Nilfisk Advance Lda Sintra Business Park Zona Industrial Da Abrunheira Edificio 1 10 A Sintra P 2710 089 www nilfisk pt RUSSIA Nilfisk Advance LLC Vyatskaya str 27 bld 7 1st floor Moscow 127015 www nilfisk ru SINGAPORE Nilfisk Advance Pte Ltd 22 Tuas Avenue 2 Singapore 639453 www nilfisk com SPAIN Nilfisk Advance S A Torre D Ara Passeig del Rengle 5 Plta 10 Matar E 0830222 www nilfisk es SWEDEN Nilfisk ALTO Aminogatan 18 M lndal S 431 53 www nilfisk alto se SWITZERLAND NA Sondergger AG Nilfisk ALTO Generalvertretung Muhlestrasse 10 CH 9100 Herisau www nilfisk alto ch TAIWAN Nilfisk Advance Ltd Taiwan Branch H K No 5 Wan Fang Road Taipei www nilfisk advance com tw THAILAND Nilfisk Advance Co Ltd 89 Soi Chokechai Ruammitr Viphavadee Rangsit Road Jomphol Jatuchak Bangkok 10900 www nilfisk com TURKEY Nilfisk Advance A S Serifali Mh Bayraktar Bulv
7. spray lance has been removed NOTE The fuel engine stops automatically if the oil level is low You can start the petrol engine again once you have added oil does not apply to POSEIDON 2 31 PE 24 Original Instructions 6 2 3 Checking the oil level 6 2 4 Changing the pump gear oil POSEIDON PE DE Check whether the oil level is in the middle of the oil inspection glass Top up with oil if necessary see section 8 3 for type of oil ch Before changing the oil allow the pressure washer to become warm 2 Unscrew the plugs at the top and the bottom of the pump 3 Allow the oil to drain into a suitable container min 1 capacity and dispose of oil in compliance with regulations 4 Mount plug at the bottom of the pump 5 Fill pump with fresh oil see 8 3 for oil type and quantity 6 Check the oil level see 6 2 3 Original Instructions 25 POSEIDON PE DE 7 Troubleshooting Fault Cause Remedy Pressure drop gt Air in the system gt High pressure nozzle blocked worn gt Pressure control on the lance is not set correctly gt Engine speed too low Vent the system by operating the spray gun several times at short intervals If necessary dismount the lance see section 4 2 2 Clean replace the high pressure nozzle Set the required working pressure Contact Nilfisk ALTO Service Department
8. 1 PE POSEIDON POSEIDON POSEIDON POSEIDON 3 36 PE POSEIDON 5 54 DE POSEIDON 5 47 PE 5 53 PE 5 67 PE Water flow max Water flow Q Ec Max water inlet temperature Min max water inlet pressure Dimensions LxWxH Noise power level LWA Thrust Suction height at max 8 C Oil quantity in pump gear Oil quantity in motor 60 60 1 10 1 10 800 x 565 x 1010 105 104 45 46 58 45 0 5 0 5 1 1 0 56 0 27 0 56 0 27 141 1 1 1 1 1 65 Oil type motor pump gear Vibrations We reserve the right to make alterations 8 4 C EC Declaration of Conformity SAE 15 40 2 5 m s Declaration of Conformity Product High Pressure Washer Type POSEIDON 2 31 PE POSEIDON 3 36 PE POSEIDON 5 47 PE POSEIDON 5 53 PE POSEIDON 5 67 PE POSEIDON 5 54 DE Description 250 bar 20 MPa Petrol driven Diesel driven The design of the unit corresponds to the following pertinent regulations 2006 42 EC 2004 108 EC EC Machine Directive EC EMC Directive Applied harmonised standards EN 2100 1 EN 12100 2 EN 60335 2 79 EN 55012 Applied national standards and technical specifications DIN EN 60335 2 79 Name and address of the person authorised to compile the technical file Identity and signature of the person empowered to draw up the decla ration on behalf of the manufacturer Anton S rensen General Manager Technical Operations EAPC Ni
9. Operating instructions Nilfisk ALTO 106169229 c works for you Instruktionsbog reto kota ko rp ek ide eti k sak de 3 15 CEN User manual seiseeieesiieseeeiereeirrnerrrrserrrrerrrrrnne 16 28 Betriebsanleitung cccccceeeeseeeeseeeeeeeeeenees 29 41 Manuel d instructions ccccccssseeceeeeeeesteeees 42 54 QD Manuale di letruziont 55 68 ES Manual de instrucciones icis d tersoitatakstiedsnmionades 69 82 CEL YXEIPIOIO D NYIW ak saka son k dtan kasse bo n kasAke 83 96 Manual de Instru es eiegtegeeeggeEt ege deier 97 110 e EE 111 124 Instrukcja obs ugi EE 125 138 Ge N vod k obsluze wi4s bikikosiacktsskokbaissisasesasaseskosikt 139 151 D zemeltet si tmutat ce eeecseeeeeenees 152 164 Gk N vod na DOSSIER ee Seege eegnen 165 177 QD Gebruikersbandlelding 178 194 Printed in Hungary Copyright 2012 Nilfisk ALTO POSEIDON PE DE Contents Symbols 1 Important safety notes 2 Description 3 Before starting the pressure washer 4 Operation and use 5 After using the pressure washer 6 Maintenance 7 Troubleshooting 8 Further information 2 1 2 2 3 1 4 1 4 2 4 3 5 1 5 2 5 3 6 1 6 2 8 1 8 2 8 4 Seege eege 17 erdege Eege ege 17 a1G ale Co SE ee ee 19 Operating elements A 19 Setting up the pressure washer 20 elle 20 Start the pressure washer ssisidsiesiiiaiieianniiieanesiiiniaan 21 Using COLO go 21911 A
10. el cock fill with fuel 8 Further information 8 1 Recycling the pressure a Ca 8 2 Guarantee If the pressure washer is discarded make it unusable immediately 1 Dismount the ignition plug The pressure washer contains valuable materials that should Your Nilfisk ALTO product is guaranteed for 12 months from date of purchase purchase receipt must be presented on the following conditions e that defects are attributable to flaws or defects in materials or workmanship Usual wear and tear as well as misuse are not covered by the guarantee e that repairs have not been carried out or attempted by other than Nilfisk ALTO trained service staff e that only original accessories have been applied be recycled Contact your local waste disposal site If you have any queries please contact your local authorities or your nearest dealer e that the product has not been exposed to abuse such as knocks bumps or frost e that the instructions in the manual have been carefully observed A warranty repair comprises the replacement of defective parts but it does not cover freight and packaging charges Besides we refer to national Sale of Goods Act Any illegitimate guarantee repair will be invoiced l e malfunctions due to causes mentioned in section 7 Trouble shooting of the instruction manual Original Instructions 27 POSEIDON PE DE 8 3 Technical data Working pressure 2 3
11. he jet towards yourself or towards other persons in order to clean clothes or footwear Do not use the washer when other people without protective Original Instructions 17 POSEIDON PE DE clothing are in the working area Check that cleaning will not result in dangerous substances e g asbestos oil being washed off the object to be cleaned and harming the environment Do not clean delicate parts made of rubber fabric etc with the round jet Hold the nozzle at a distance of at least 15 cm when cleaning with the high pressure flat jet Although extremely easy to operate children should not be allowed to use the pressure washer Do not use the high pressure hose for lifting loads Do not continue to use the washer if the quick coupling or high pressure hose is damaged Never use the machine in areas where there is danger of fire or explosion When using the pressure washer stand at least 1 m from buildings etc Ensure an adequate air circulation Do not cover the washer or operate it in inadequately ventilated rooms The exhaust fumes are dangerous Store the pressure washer where it will not be exposed to frost Never operate the pressure washer without water Even brief shortages of water result in severe damage to the pump seals Maintenace and repair CAUTION Before cleaning and servicing the high pressure washer always remove the ignition plug cable first Carry out onl
12. lfisk Advance A S Sognevej 25 DK 2605 Brandby E ien General Manager Technical Operations EAPC Nilfisk Advance A S Sognevej 25 DK 2605 Br ndby Place and date of the declaration Hadsund March 1 2012 28 Original Instructions Nilfisk ALTO works for you HEAD QUARTER DENMARK Nilfisk Advance A S Sognevej 25 DK 2605 Brandby Tel 45 4323 8100 www nilfisk advance com SALES COMPANIES ARGENTINA Nilfisk Advance srl Herrera 1855 6 floor Of A 604 ZC 1293 Ciudad Aut6noma de Buenos Aires Argentina www nilfisk alto com AUSTRALIA Nilfisk ALTO Unit 1 13 Bessemer Street Blacktown NSW 2148 Australia www nilfisk alto com au AUSTRIA Nilfisk ALTO Gesch ftsbereich der Nilfisk Advance GmbH MetzgerstraBe 68 A 5101 Bergheim Salzburg www nilfisk alto at BELGIUM Nilfisk Advance NV SA Riverside Business Park Boulevard Internationalelaan 55 Batiment C3 C4 Gebouw Bruxelles 1070 Brussel www nilfisk be CHILE Nilfisk Advance S A San Alfonso 1462 Santiago www nilfisk com CHINA Nilfisk Advance Cleaning Equipment Shanghai Co Ltd No 4189 Yindu Road Xinzhuang Industrial Park Shanghai P R C 201108 www nilfisk cn CZECH REPUBLIC Nilfisk Advance s r o Do Certous 1 VGP Park Horn Pocernice Budova H2 CZ 190 00 Praha 9 www nilfisk cz DENMARK Nilfisk ALTO Danmark Industrivej 1 Hadsund DK 9560 www nilfisk alto dk FINLAND Nilfisk Advance OY Ab Koskel
13. n off 4 Connect the suction hose to the water inlet of the washer and place it in a tank containing anti freeze 5 Start the washer 6 Hold the spray gun over the tank containing anti freeze and activate it to start suction of anti freeze 7 During suction operate the spray gun two or three times 8 Lift the suction hose from the tank containing anti freeze and activate the spray gun to pump out the remaining anti freeze 9 Stop the washer Original Instructions 23 POSEIDON PE DE 6 Maintenance 6 1 Maintenance plan 6 2 1 Clean water filter 6 2 2 Clean high pressure nozzle 6 2 3 Check oil level 6 2 4 Change oil Note First time after 50 hours every six months or 500 operating Maintenance of motor according to separate operating instructions from the engine supplier 6 2 Maintenance work 6 2 1 Clean water filter 6 2 2 Clean high pressure nozzle A water filter is fitted on the water inlet to prevent large particles of dirt from entering into the pump A blocked nozzle causes excessive pump pressure It must therefore be cleaned immediately 1 Stop the washer 2 Remove the lance 3 Clean the nozzle with a needle 4 Rinse the lance with water from the nozzle side 1 Unscrew the union nut 2 Remove the filter and rinse it Replace damaged filter 3 Tighten the union nut gently so as to avoid damaging the gasket WARNING Use the cleaning needle only when the
14. nlet filter Connection for high pressure hose Pressure gauge Oil level gauge Regulation of water volume Filling of oil Detachable handle Original Instructions 19 POSEIDON PE DE 3 Before starting the pressure washer 3 1 Setting up the pressure washer 4 Operation and use 4 1 Connections 4 1 1 Connecting the lance to the spray gun 4 1 2 Connecting the high pressure hose and the water hose 1 Before using the pressure washer for the first time check it carefully to detect any faults or damage 2 In the event of any damage contact your Nilfisk ALTO dealer immediately 3 Check whether the oil level is in the middle of the oil inspection glass This also applies to machines with gear 1 Pull the blue quick release grip A of the spray handle backwards 2 Insert the nipple of the spray lance B into the quick release connection and release it 3 Pull forward the spray lance or any other accessory to ensure correct mounting before starting the machine NOTE Always remove any dirt from the nipple before connecting the lanse to the spray gun 1 Connect the high pressure hose to the high pressure inlet by means of the quick coupling Use max 50 m extension hose 2 Before connecting the water hose to the washer rinse the water hose briefly to prevent sand and other dirt from entering into the washer 3 Open the tap
15. ontie 23E Espoo Fl 02920 www nilfisk fi FRANCE Nilfisk Advance SAS Division ALTO BP 246 91944 Courtaboeuf Cedex www alto fr com GERMANY Nilfisk ALTO Gesch ftsbereich der Nilfisk Advance AG Guido Oberdorfer StraBe 10 89287 Bellenberg www nilfisk alto de GREECE Nilfisk Advance A E 8 Thoukididou Str Argiroupoli Athens GR 164 52 www nilfisk gr HOLLAND Nilfisk Advance B V Versterkerstraat 5 1322 AN ALMERE www nilfisk nl HONG KONG Nilfisk Advance Ltd 2001 HK Worsted Mills Ind Bldg 31 39 Wo Tong Tsui St Hong Kong Kwai Chung N T www nilfisk com HUNGARY Nilfisk Advance Kereskedelmi Kft H 2310 Szigetszentmikl6s Lakihegy Il R k czi Ferenc ut 10 www nilfisk hu INDIA Nilfisk Advance India Limited Pramukh Plaza B Wing 4th floor Unit No 403 Cardinal Gracious Road Chakala Andheri East Mumbai 400 099 www nilfisk com IRELAND Nilfisk Advance 1 Stokes Place St Stephen s Green Dublin 2 www nilfisk alto ie ITALY Nilfisk Advance S p A Strada Comunale Della Braglia 18 Guardamiglio Lombardia 26862 www nilfisk it JAPAN Nilfisk Advance Inc 1 6 6 Kita Shinyokohama Kouhoku Ku Yokohama 223 0059 www nilfisk advance co jp KOREA Nilfisk Advance Korea 471 4 Kumwon B D 2F Gunja Dong Gwangjin Gu Seoul www nilfisk advance kr MALAYSIA Nilfisk Advance Sdn Bhd SD 33 Jalan KIP 10 Taman Perindustrian KIP Sri Damansara 52200 Kuala Lumpur Malaysia www
16. re use check that the high pressure cleaner is in a safe and proper condition Operate the pressure washer only in an upright position Important notes Do not connect the pressure washer directly to the public drinking water mains observe DIN 1988 and EN 1717 A connection is permitted however e briefly to a pipe interrupter with moving section e with a free outlet Water may also be drawn from an open container or from a well or surface water not intended for the drinking water supply Please use suction set for this Ensure that neither dirty water nor liquids containing solvents are sucked in POSEIDON PE DE This symbol is used to mark safety instructions that must be observed to prevent damage to the machine and its performance This symbol indicates tips and instructions to simplify work and to ensure a safe operation Please observe the regulations and provisions applicable in your country Before putting the high pressure washer into service carry out a visual check of all the major components High pressure jets can be dangerous if misused The jet must not be directed at persons animals live electrical equipment or the pressure washer itself During operation of the washer recoil forces are produced at the spray lance and when the lance is held at an angle a torque is also created The lance must therefore be held firmly in both hands Risk of injury Do not direct t
17. system NOTE If it requires too much power to start the engine it can be facilitated by removing the spray lance and activate the spray gun during startup 4 When using this machine in suction mode first ensure that the system has been bled of air by letting the machine run without spray lance mounted until all air has escaped breaks of more 3 than three minutes switch off the washer During work NOTE For automatic suction from a tank watercourse or similar supply the inlet hose must be filled with water before you start The suction height continued gt Original Instructions 21 EN POSEIDON PE DE 4 2 3 Start POSEIDON PE depends on the water temperature Max suction height see section 8 3 Technical Data is reached with cold water up to 8 C With 70 C 60 C warm water the machine must be under or at the water level 1 Switch on the ignition by pushing the ON OFF button of the machine The charging a a lt 4 3 Using detergents If the water being suctioned contains particles a suction filter must be mounted on the end of the hose In case of risk of running sands a sand filter must be attached oil light indicators will turn on Move the throttle lever to SLOW or RUN position 3 Push the start button until the machine starts Now the charging oil light indicators will turn off If not stop the machine
18. y the maintenance operations described in the operating instructions Use only original Nilfisk ALTO spare parts Do not make any technical modifications to the high pressure washer CAUTION High pressure hoses fittings and couplings are important for the safety of the washer Use only high pressure parts approved by the manufacturer CAUTION Failure to observe these instructions can endanger your safety Please contact the Nilfisk ALTO service department or an authorised specialist work shop for all other maintenance or repair work Testing The machine satisfies IEC EN 60335 2 79 standards The high pressure washer should be examined as needed or at least once a year by a technician to make sure that it is fail safe Our service technicians are at your disposal for assistance and advice Safety device The high pressure pump is equipped with a safety valve that redirects the by pass pressure back to the suction side of the pump The safety device is set and sealed at the factory and must not be adjusted 18 Original Instructions 2 2 1 2 2 POSEIDON PE DE Description Intended use This high pressure washer has been designed for professional use in agriculture transport industry construction industry etc Operating elements Start stop switch Lance Holder for lance Holder for high pressure hose High pressure hose Spray gun Water connection and water i
Download Pdf Manuals
Related Search