Original Operating Instructions
Contents
1. PZ 824 S43 PZ 824LS44 Item number PZ 824LS XX see figure Send your orders per fax to 49 0 9364 8176029 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info Q visomax de www visomax de2. P Po sssoncl Tools 2 Safety notes WARNING Read and observe all notes before installation operation repair maintenance and replacement of accessories as well as before work near the compressed air tool Non observance of the following safety notes may lead to the following severe injuries Keep the safety notes well and hand them over to the operator Safety at the workplace Observe surfaces that may have turned slippery by use of the machine Observe tripping dangers from the air hose Slipping tripping and falling are main reasons for injury atthe workplace Do not work with the compressed air tool in potentially explosive environments in which there are flammable liquids gases or dust Processing the workpiece may cause sparksthat may ignite the dust or vapours Keep audience children and visitors away from your workplace while using the compressed air tool When distracted by other persons you may lose control of the compressed airtool Safety when handling compressed air tools Never point the air flow at yourself or others and conduct cold air away from your hands Compressed air may cause severe injury Check connections and supply lines All maintenance units couplings and hoses must be sized for the pressure and air volume according to the technical data Too low pressure impairs function of the compressed air tool too high pressure may cause property damage and injury Protect the hos
3. any accessories or wear parts This preventive measure prevents inadvertent start up of the compressed air tool 1 Support disc PZ 100 A 30 NV 2 2 Grinding disc The surface of the support disc consists of hook and loop fabric so that grinding discs can be attached quickly with hook and loop adhesion Push the grinding disc 2 firmly against the bottom of the supporting disc 1 Note gt Observe that self adhering grinding discs are attached concentrically on the supporting disc Remove dirt and dust from the supporting disc before putting on a new grinding disc e g with a brush Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold 6 4 Replacing supporting disc gt Interrupt the air supply before you replace any accessories or wear parts This preventive measure prevents inadvertent start up of the compressed air tool 1 Support disc PZ 100 A 15 NV 1 Remove the grinding disc Turn the supporting disc 1 counter clockwise off of the drive shaft Remove dust and dirt e g with a brush Do not clean the device with compressed air Turn the new support disc onto the drive shaft clockwise 1 Support disc 2 Balancing shaft 3 Latching pin PZ 100 A 30 NV 2 Remove the grinding disc Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81
4. described compressed air spot sanders of Visomax Coating GmbH The device documentation must be kept at the site of use of the compressed air spot sanders at all times so that they are available on demand Warranty All warranty claims of the operator shall expire two years after handover of the purchased object except in case of liability from wilful or grossly negligent action Wear parts are excluded from this Damages claims against Visomax Coating GmbH due to contractual or pre contractual violations of obligations shall only apply at wilful intent or gross negligence of the purchaser his representatives or servants or at violation of essential contractual obligations If Visomax Coating GmbH grossly violates contractual obligations the liability shall be limitedin scope to the typically foreseeable damage In case of impossibility or default the damages claims are limited to reimbursement of the typical foreseeable damage If the servant of Visomax Coating GmbH acts grossly negligent Visomax Coating GmbH shall be liable at the scope of the typically foreseeable damage Liability from violation of essential contractual obligations or malice of the seller shall not be affected In case of violations of body well being and health the applicable statutory provisions shallapply Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometcolz 7
5. this test time Do not use the compressed air tool without grinding or polishing agent The grinding disc will wear down otherwise and the grinding materials can no longer be safely attached The compressed air tool can discharge electrostatically if you grind plastic and other non conductive materials When using the compressed air tool the operator may experience unpleasant sensations in his hands arms shoulders neck or other body parts when performing work related activities If the operator suffers any symptoms such as continued feeling unwell complaints pounding pain tingling burning or stiffness in himself these warning signs should notbe ignored The operator should report them to his employer and consult a qualified doctor Do not use any cutting discs The permitted rotating speed of a tool must be at least as high as the maximum rotating speed indicated on the compressed air tool Accessories turning more quickly than permitted may break and fly around Observe that self adhering grinding and polishing discs are attached concentrically onthe grinding disc WARNING The dust arising when sanding grinding polishing and similar work may be carcinogenic teratogenic or mutagenic Some of the substances contained in these dusts include Lead in lead containing paints and varnishes Crystalline silica in bricks cement and other masonry work Arsenic and chromate in chemically treated wood The risk of illne
6. tool Be ready for unexpected movements of the compressed air tool that may occur due to reaction forces or breaking of the usage tool Hold on to the compressed air tool well and put your body and your arms into a position in which you can catch these movements These precautions can avoid injury Take a comfortable position for working with this compressed air tool observe secure hold and avoid unsuitable positions or such positions where it is difficult to remain balanced The operator should change his body posture during extended work which may help avoid discomfort and fatigue At interruption of the air supply or reduced operating pressure switch off the compressed air tool Check the operating pressure and restart at best operating pressure Use only the lubricants recommended Never put your hand close to turning tools You may injure yourself Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de PrometoolZ Po sssoncl Tools Do not use any damaged tools Check tools for splintering and cracks wear or strong wear before each use If the compressed air tool or the tool falls down check if it is damaged or use an undamaged tool When you have checked and used the tool you and persons nearby must stay outside of the level of the rotating tool Let the device run at maximum speed for one minute Damaged tools usually break within
7. 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools gt Turn the support disc 1 until the bore in the balancing shaft 2 is visible in theopening of the circlip arrow Push the latching pin 3 into the bore to fasten the drive shaft Turn the supporting disc 1 counter clockwise off of the drive shaft Remove dust and dirt e g with a brush Do not clean the device with compressed air Turn the new support disc onto the drive shaft clockwise Remove the latching pin 3 VV v v V Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info Q visomax de www visomax de PrometoolZ S Bovcssioncl Tools 7 Operation 7 1 Notes on the operation Remove the setting tools before taking the compressed air tool into operation A setting tool in a turning device part may cause injury Wait until the compressed air tool has stopped before you put it down Observe that self adhering polishing pads are attached concentrically on the supporting disc At interruption of the air supply or reduced operating pressure switch off the compressed air tool Check the operating pressure and restart at best operating pressure Switch on the compressed air tool put it onto the surface to be processed with the entire polishing surface and move it over the workpiece with moderate pressure The polishing output and the polishing pattern are essent
8. D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de PrometoolZ sj Po sssoncl Tools ltemno Description Jitemno Description gt Grip installation O ring 1xID 4 Digital display Sea Wedge 58106 17B 58106 45 58106 18 Safety trigger 58106 46 58106 19 Spring pin 3x16 mm 58106 47 Pad screw M4x5 mm 58106 22 Spring pin 2x4 mm 58106 48 er supporting disc 30 58106 23 Ball bearing lt 696 ZZ gt 58106 49 Tr supporting disc 30mm 58106 24 End plate 58106 50 ng supporting disc 38mm R58106 43Z Item number PZ 58106 XX see figure 58106 15 O ring S12 5 58106 43 Pad fastening 58106 16 O ring S15 58106 44 O ring P15 Send your orders per fax to 49 0 9364 8176029 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools 14 2 Model PZ 100 A 30 NV 2 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de PrometoolZ 77 Po sssoncl Tools ltemno Description itemno Description gt PZ 824LS01 Holder O ring Valve housing PZ824LS26 Spring pin PZ 824LS27 PZ 824LS28 Ball bearing PZ 824LS04 Modi nes PER PZ B2ALS31 PZ B24LS32 PZ 8241 533 PZ 824LS45 Repair set parts no 34 39 PZ 8241 540 PZ 824LSA1 Pz8241S42 Old
9. Prometoold Original Operating Instructions Compressed air spot sander 1 vibration PZ 100 A 15 NV 1 Compressed air spot sander 1 eccentric PZ 100 A 30 NV 2 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools Note This print is part of the documentation for the compressed air spot sanders of Visomax Coating GmbH Copyright This printed document are copyright protected Any use outside of the narrow limits of copyright protection is not permitted and punishable without the consent of Visomax Coating GmbH This also applies to reproductions translations micro film and storage and processing in electronic media Violations commit to damages Imprint Visomax Coating GmbH Sonnenstrasse 55 97225 Zellingen Germany 2014 O Visomax Coating GmbH All rights reserved Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info Qvisomax de www visomax de Prometoold 7 Po sssoncl Tools Content 1 Notes on the operating instructions 5 2 Safety notes 6 3 Symbols and their meaning 13 3 1 Setup and meaning of other notes and symbols 13 Intended us
10. Work with care to avoid injury and property damage as well as accidents 3 1 Setup and meaning of other notes and symbols Other notes in these operating instructions are structured as follows ik Signal word important note Useful note on handling care or maintenance of the device or system Instructions on compliance with safety notes gt Instructions for action Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools 4 Intended use The compressed air tool is intended for dry grinding of wood plastic metal grout and painted surfaces Any other or additional use is deemed non intended Visomax Coating GmbH shall not be liable for any resulting damage The risk is solely withthe operator ik Note The operator must not manipulate the compressed air spot sander unless Visomax Coating GmbH expressly authorises him to do so in writing Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de PrometoolZ PZ 100 A 15 NV 1 PZ 100 A 30 NV 2 Connection of compressed air hose On off switch safety trigger Setting wheel rotating speed RR W N bk Display pressure display Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info Q visomax de www v
11. e 14 5 Device setup 15 6 Mounting 16 6 1 Connect compressed air hose 16 6 2 Connect compressed air hose with muffler 16 6 3 Attach grinding disc 18 6 4 Replacing supporting disc 19 7 Operation 21 7 1 Notes on the operation 21 7 2 Switching the pressure display on off only PZ 100 A 15 NV 1 21 7 3 Switching the device on off safety trigger 22 7 4 Setting rotating speed 23 8 Maintenance and cleaning 24 9 Disposal 24 10 Technical data 25 11 Declaration of conformity 26 12 Scope of delivery and accessories 27 13 Parts list 28 13 1 Model PZ 100 A 15 NV 1 28 13 2 Model PZ 100 A 30 NV 2 30 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools 1 Notes on the operating instructions These operating instructions contain information and instructions for safe operation ofthe compressed air spot sanders of Visomax Coating GmbH For your own safety and to protect from injury familiarise yourself well with the safety notes and observe them precisely Visomax Coating GmbH assumes no liability for the non observance of these operating instructions Target group These operating instructions are targeted at operators or the persons charged by the operator for the compressed air spot sanders of Visomax Coating GmbH Storage These operating instructions are part of the device documentation and a fixed part ofthe
12. e and see a doctor Hold the compressed air tool in a not too tight but safe grip under compliance withthe required hand reaction forces The vibrations may increase the harder you are holdingthe tool Never carry the compressed air tool by the hose Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info Q visomax de www visomax de Prometoold Use eye protection Use gloves Use breathing protection Use safety shoes Use safety helmet Use hearing protection Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools 3 Symbols and their meaning The safety notes in these operating instructions are structured as follows Signal word danger warning caution attention Type and source of danger Possible consequence s of non observation Measure s to avoid the danger The signal word Danger marks a directly threatening danger with the consequence of death or severe injury The signal word Warning marks a possible dangerous situation with the consequence of death or severe injury The signal word Caution marks a possible dangerous situation with the consequence of light injury The signal word Attention marks a possible property damage with damage to the device system or directenvironment Safety notes must be complied with
13. ect the compressed air tool to the airsupply when switched on this may cause accidents Remove setting and mounting tools before you switch on the compressed air tool Asetting tool in a turning tool of the compressed air tool may cause injury Ensure a safe stance and always maintain balance A safe stance and suitable posture make it possible to control the compressed air tool better in unexpected situations Do not wear any loose clothing or jewellery Keep hair clothes and gloves away from moving parts Loose clothes jewellery or long hair may be caught by moving parts If vacuum extraction and collection devices can be installed ensure that they areconnected and used properly Using such devices reduces danger from dust Do not directly inhale the exhaust Avoid getting exhaust into your eyes The exhaust of the compressed air tool may contain water oil metal particles and contamination from the compressor This may cause damage to health Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools Careful handling when using compressed air tools Use clamping devices or a vice to hold and support the workpiece If you hold the workpiece with your hand or press it against your body you cannot securely operate the compressed air tool Do not overload the compressed air tool Use the intended compre
14. es from bending bottlenecks solvents and sharp edges Keep the hoses away from heat oil and rotating parts Replace a damaged hose without delay A defective supply line may cause the compressed air hose to jerk and cause injury Swirled up dust or chips may cause severe eye injury Observe that clamps are always tightened firmly Clamps that are not tightened or thatare damaged may let air escape uncontrolledly Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info Q visomax de www visomax de Prometoold Pa Po sssoncl Tools Safety of persons Work attentively and carefully and perform the work with a compressed air tool with reason Do not use compressed air tools when tired or under the influence of drugs alcohol or medication Amoment s inattention when using the compressed air tool may cause severe injury Wear personal protection equipment and always wear safety goggles Wearing personal protection equipment such as breathing protection slip proof safety shoes safety helmet or hearing protection according to the instructions of your employer or as required n the work and health protection provisions reduces the risk of injury Avoid inadvertent commissioning Ensure that the compressed air tool is switched off before connecting the air supply lifting it up or carrying it If you activate the on off switch when carrying the compressed air tool or if you conn
15. following directives 2006 42 EC Machinery directive 2011 65 EC RoHs Applied standards EN ISO 11148 8 EN 4414 EN 12100 2010 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info Q visomax de www visomax de 12 Scope of delivery and accessories Scope of delivery Accessories Prometoold Z Po sssoncl Tools Compressed air spot sander PZ 100 A 15 NV 1 Compressed air spot sander PZ 100 A 30 NV 2 Latching pin Compressed air hose Compressed air hose with muffler PZ multifunctional oil M2309 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssonel Tools 13 Maintenance Tools Bearing Puller RT BP50 PZ 100 A 15 NV 1 Bearing Puller RT BP50 1 PZ 100 A 15 NV 1 Rotor Spinde Remover RT RS16 PZ 100 A 15 NV 1 Grease Dispenser Grease 100g Refill Head with Grease PZA2305U PZ A230ST PZ 100 A 15 NV 1 PZ 100 A 15 NV 1 PZ 100 A 30 NV 2 PZ 100 A 30 NV 2 Pin punch with guide sleeve 0 9mm PZ A748000 PZ 100 A 15 NV 1 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de visQmax 14 Parts list 14 1 Model PZ 100 A 15 NV 1 a Fa 4 ag s Optional 47 Visomax Coating GmbH Sonnenstrasse 55
16. g rotating speed 1 On off switch 2 Speed controller PZ 100 A 30 NV 2 The speed controller can be used to set the required speed during operation as well The required speed depends on the material and the working conditions gt Maximum rotating speed Turn the speed control to the stop counter clockwise gt Minimum speed Turn the speed control to the stop clockwise Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Pio sssionel Tools 8 Maintenance and cleaning Have maintenance and repair work only performed by qualified specialists This ensuresthat the safety of the compressed air tool is retained 1 Connection sockets for compressed air hose Before starting work spray PZ multifunctional oil M2309 into the connection socket for the compressed air hose 1 Oiler Before starting work spray PZ multifunctional oil M2309 into the oiler 1 Clean the compressed air tool regularly of dust and dirt Clean the plastic parts only with a mild detergent gt Do not clean the tool with compressed air Keep plugs and couplings of the air supply free of dust and dirt 9 Disposal Compressed air tools accessories and packaging should be supplied toenvironmentally compatible recycling Dispose of lubricants and cleaning agents in an environmentally compatible manner Observe the statutory p
17. ially determined by the choice of polishing pad the pre selected rotating speed and the press on pressure 7 2 Switching the pressure display on off only PZ 100 A 15 NV 1 nn pr F on 1 Button ON 2 Unit 3 Display Switching on Push the button ON and keep it pushed for approx 2 seconds until the display appears gt Repeated short pushing of the button ON permits setting of the desired unit The currently chosen setting is displayed by a bar in the display below the unit Deactivation gt Push the button ON and keep it pushed for approx 2 seconds until the display goes out Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po essioncl Tools PZ 100 A 15 NV 1 AR p 1 Activation lock Cin 10 Ng Wi HE 2 On off switch AS PZ 100 A 30 NV 2 The on off switch is secured against accidental actuation by an activation lock Toswitch on the compressed air tool fold the activation lock 1 over a Then pushthe on off switch 2 down b and keep it pushed while working To switch off the compressed air tool release the on off switch 2 The activation lockis returned to the locking position spring actuated Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de PrometoolZ Po sssoncl Tools 7 4 Settin
18. isomax de PrometoolZ Po sssoncl Tools 6 Mounting 6 1 Connect compressed air hose 1 Coupling compressed air hose 2 Connection socket PZ 100 A 30 NV 2 Connect the coupling of the compressed air hose 1 to the connection socket 2 ofthe compressed air tool 6 2 Connect compressed air hose with muffler 1 Connection sockets for compressed air hose 2 Screw connection compressed air hose with muffler 3 Connection socket of compressed air hose with muffler PZ 100 A 15 NV 1 4 Coupling compressed air hose Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po essioncl Tools 1 Connection sockets for compressed air hose 2 Screw connection compressed air hose with muffler 3 Connection socket of compressed air hose with muffler PZ 100 A 30 NV 2 4 Coupling compressed air hose Screw the connection socket 1 for the compressed air hose out of the device Screw the compressed air hose with muffler 2 to the device Connect the coupling of the compressed air hose 4 to the connection socket ofthe compressed air hose with muffler 3 Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de PrometoolzZ Po sssoncl Tools 6 3 Attach grinding disc gt Interrupt the air supply before you replace
19. not be used Changes may reduce the effectiveness ofthe safety measures and increase the risks for the operator Have your compressed air tool only repaired by qualified specialists and only with genuine spare parts This ensures that the safety of the compressed air tool is retained Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Pa Po sssoncl Tools Safety notes for compressed air eccentric devices When the workpiece or one of the accessories or even the compressed air tool itself breaks parts may be ejected at high speed In operation and at repair and maintenance work as well as when replacing accessories at the compressed air tool always wear impact resistant eye protection The degree of required protection should be evaluated separately for every single use Wear a safety helmet when performing work overhead This avoids injury Observe a safe distance from your work area in other persons Everyone who enters the work area must wear personal protection eguipment Fragments of the workpiece or broken cutting discs may fly away and cause injury even outside of the direct workingarea Caution Tools may grow hot when the compressed air tool is operated for anextended time Use safety gloves The operator and maintenance staff must by physically able to handle the size weight and output of the compressed air
20. rovisions Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold 57 Po sssoncl Tools 10 Technical data Compressed air spot sander PZ 100 A 15 NV 1 PZ 100 A 30 NV 2 Length 187 mm Weight 0 65 kg Angle Drive Gradual Muffler rear UT o Type Vibration Rotating Power 0 22 KW Max speed 7500 rpm 0 27 m min n Air consumption Air inlet Thread size 6 5 mm Air pressure 7 Bar Noise and vibration information Noise emission values determined according to EN ISO 15744 The noise level may exceed 80 dB A when working Use hearing protection The A assessed noise level of the compressed air tool typically is Sound pressure level Lpa 75 dB A 75 dB A insecurity K 3 dB 3 dB Total vibration values An vector total of three directions and insecurity K determined according to EN 28927 Ah lt 2 5 m sec lt 2 5 m sec K 1 5 m sec 1 5 m sec Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold Po sssoncl Tools 11 Declaration of conformity G I The manufacturer Visomax Coating GmbH Sonnenstrafse 55 97225 Zellingen explains under its sole responsibility that the machine compressed air spot sander models PZ 100 A 15 NV 1 and PZ 100 A 30 NV 2 correspond to all relevant provisions ofthe
21. ss depends on how often you are exposed to these substances To reduce the danger only work in well ventilated rooms with the corresponding safety equipment e g with specifically constructed breathing protection that will filter out even the smallest dust particles Visomax Coating GmbH Sonnenstrasse 55 D 97225 Zellingen Fon 0 93 64 81 76 00 Fax 0 93 64 81 76 029 info visomax de www visomax de Prometoold 7 Po sssoncl Tools The work with specific materials may cause dusts and vapours that may form a potentially explosive atmosphere Work with compressed air tools may cause sparks that may ignite the dust or vapours When working at the workpiece additional noise may arise that can be avoided by suitable measures such as use of insulation materials when ringing sounds occur at the workpiece If the compressed air tool has a muffler always ensure that it is in place whenthe compressed air tool is operated and that it is in a proper working condition The effect of vibrations may cause damage to the nerves and impairment of the blood circulation in the hands and arms Wear close fitting gloves Handles of compressed air tools grow cold from thecompressed air flow Warm hands are less sensitive to vibrations Loose gloves may be caught byrotating parts If you find that the skin on your fingers or hands becomes numb tingles is painful orturns white stop working with the compressed air tool inform your employe
22. ssed air tool for your work The right compressed air tool will enable you to work better and more safely inthe indicated power range Do not use any compressed air tools with a defective on off switch A compressed airtool that can no longer be switched on or off is dangerous and must be repaired Interrupt the air supply before making any settings on the device replacing accessories orat extended non use This preventive measure prevents inadvertent start up of the compressed air tool Keep unused compressed air tools out of the reach of children Do not let persons usethe compressed air tool who are not familiar with it or who have not read these instructions Compressed air tools are dangerous when used by inexperienced persons Care for the compressed air tool diligently Check if moving device parts work properly and are not caught or if parts are broken or so damaged that the function of the compressed air tool is impaired Have damaged parts repaired before use of the compressed air tool Many accidents have their cause in badly serviced compressed air tools Use compressed air tools accessories usage tools etc according to these instruction Consider the working conditions and the work to be performed in this This reduces dust development vibrations and noise development where possible The compressed air tool should only be set up adjusted or used by qualified andtrained operators The compressed air tool must
Download Pdf Manuals
Related Search