Operating Instructions for Universal Temperature
Contents
1. E Set temperature 0 5K Pal Acquisition of the values lt Return to normal control mode lt Set temperature 0 5K If no key has been activated within a period of approx 5 seconds the system returns to normal control mode again The changed temperature value is being taken over and imported The adjusted set temperature con tinues to be effective until the moment the operating mode is changed no matter if changing manually or automatically after triggering by the switch clock 4 2 Selection of the operating mode AutoECO 6 Comfort ECO M Fr15072011 7 Fr15072011 Frie0720011 12 3 12 34 12 34 OFF Mode Menul Mode v v Actuating the touch key Mode allows to change the operating mode in the order shown below Automatic mode in compliance with the related weekday mode settings Comfort mode permanently ECO mode permanently Operating mode OFF In OFF mode the controller activates the heating when underrunning a temperature level of approx 5 C and deactivates the operations when exceeding a temperature level of approx 6 C This antifreezing function helps prevent rooms from cooling down thoroughly and protects against the occurrence of frost damage 5 Main menu Party Holiday Time2. 1 Safety information Expert electricians only may open this device in due compliance with the wiring diagram shown in the housing cover on the housing represented in the corresponding operating instructions All expert electricians charged with the execution of such works must comply with the relevant safety regu lations currently operative and in force Caution The operation of the con troller in the vicinity of other devices that do not comply with the EMC direc tives may affect its functions The company charged with the installation of the device must after the completion of the installation works instruct the user of the control system into its functions and in how to operate it correctly These operating instructions must be kept at a place that can be accessed freely by the operating and or servicing personnel in charge 2 Application functional description emergency operation The controller described in these instructions is provided for flush installa tion and has been specially devised for the time dependent control of the temperatures in individual rooms or of the temperatures produced by elec tric or warm water heating systems systems with normally closed valve actuators The device can be used as floor or as room temperature controller with additional floor temperature controller function Operation in emergency mode is triggered if the internal or external sensor is defective The same appl
3. Temperature ui 17 0 GENK a Already existing holiday data can be cancelled by simply changing via the main menu over to the holiday submenu Actuating the key allows to leave this menu Factory setting 17 C 17 5 3 Setting of the time Entry of hours Hour 1 Termination of entries returning to the main menu Import of the selected value 4 changing to the minute entry display Hour 1 18 5 3 Entry of minutes S 12 34 End Ok Minute 1 2 3 Termination of entries returning to the main menu Import of the selected value 4 returning to the main menu Minute 1 Actuating the ESBikey after a change of the minutes allows to reset the seconds entry to 0 19 5 4 Setting of the date Entry of the year Year 1 Termination of entries returning to the main menu Import of the selected value lt changing to the month entry display Year 1 20 5 4 Entry of the month Month 1 Termination of entries returning to the main menu Import of the selected value 4 changing to the day entry display Month 1 21 5 4
4. Selection forward Import for Sa Su m Tu Wel Ti Fr SaSu 4 End Ok gt PM 28 5 7 Information Returning to the main menu HTRRUU210 021 Version X xx gue ad 29 5 8 Settings Kevlack x DST y Valve protection 2X METIESFY PE Selection downward Termination of entries returning to the main menu Activation or deactivation of the selected function Selection upward 30 5 8 Settings K The following functions are available 1 Keylock The keylock is activated 2 minutes after actuating any of the touch keys The key icon appears on the display to indicate this locked state The touch keys can be reactivated by actuating and holding any of the keys depressed for 10 seconds 2 Automatic change between daylight saving and standard time The harmonised daylight saving time in the European Union takes effect as of the last Sunday in March i e as of 2 00 o clock a m CET and lasts until to 3 00 o clock a m on the last Sunday in October CEST each year direc tive 2000 84 EG of the European Council and Parliament The temperature controller changes the time all automatically at these dates The automatic change between daylight saving and standard time can also be deactiva
5. XC Dimplex Operating Instructions for Universal Temperature Controller BRTU 101 UN Stand 11 2011 1 Table of contents overview 1 Safety information 06 00 ccc ccc eects 4 2 Application functional description emergency operation 5 3 Operating instructions sisiusueuiissssesssessessessss 6 4 Control operation 2 0 ccc cece cece esee 7 4 1 Temporary set temperature setting 0 8 4 2 Selection of the operating mode 0 00 9 5 Main menu Lii scs ee E As eS ABS exp 10 5 1 Submenu Party suusuuuususssssssssssssssss esses 12 5 2 Setting of the holiday data sssusuuuuuuussssuueue 13 5 3 Setting of the time iiuuuiuusssssssssssssssssssssse 18 5 4 Setting of the date 0 ccc cee ees 20 5 5 Setting of the set temperatures 0 00 002205 23 5 6 Entry of the weekday programs 0 00 0e ee ees 25 9 7 Information 55 uo ip reete Eat xe etd erp I cep eit 29 5 9 Settings xxt dar E XI up One tae HUN ED eH us 30 6 Experts mernu ns rere d ogee nse EIER 33 7 Mounting connection sssssuuessssssssssssssseee 35 8 Wiring diagram and dimensioned drawing 36 9 Iechnic l d ta rrr DRE e o ERE RE 38 10 ACCESSOMES ue sene eter Po SR a OR edt 39 11 Warranty eee trou RANT Pup en ERU 39
6. Date 12 37 15072011 a T IER Sia Ea v Lo v Submenu Submenu Submenu Submenu Party Holiday Time Date see 5 1 see 52 see 5 3 see 5 4 Actuating the key fl terminates the main menu 5 Main menu Temperature Weekday program Info Settings A200C WIPO S Wr alena Ok gt a End c v v v v v v Submenu ise l Submenu temperature wee ay Info n settings see 5 5 ore eee see 5 8 gt Calling of the experts menu see 6 fi 5 1 Submenu Party 7 Party end 15 minutes Termination of data entry returning to the main menu Start of the Party function Party end 15 minutes Partv until Y Hour Minute 22 30 BENK a Actuating the ESSI touch key starts the party function Once the pre adjusted time has been attained the system switches automatically back to the previous operating mode Actuating the touch key cancels the party function at any time While operating in party mode all control operations are performed in dependence on the actually adjusted comfort temperature 12 5 2 Setting of the holiday data and entry of the month in which holidays begin Month in which holidays begin 1 Termination of the data entry returning to the main menu Changing over to the da
7. Entry of the day Day 1 Termination of entries returning to the main menu Import of the selected value 4 returning to the main menu Day 1 22 5 5 Setting of the set temperatures Entry of the comfort temperature fo qr Comfort 20 0 End Ok Pu Comfort temperature 0 5K Termination of entries returning to the main menu Import of the selected value changing to the ECO temperature entry display Comfort temperature 0 5K If using the device as floor temperature controller the desired floor tem perature can be set using this menu The same applies in regard to the setting of the desired room temperature when using it as room tempera ture controller Factory setting 20 C 23 5 5 Entry of the ECO temperature C fs ECO 17 0 ERECIESSES ECO temperature 0 5K a Termination of entries returning to the main menu Import of the selected value lt returning to the main menu ECO temperature 0 5K The maximum adjustable ECO temperature value corresponds to the comfort temperature value 1K Factory setting 17 C 24 5 6 Entry of the weekday programs Selection of the weekday Weekday backward Terminati
8. HF 8 4 K2 External floor temperature sensor incl 4 m long cable HF 8 6 K2 External floor temperature sensor incl 6 m long cable THF Sleeve to ensure the sensor is protected when installing it into the floor screed 11 Warranty The technical data specified herein have been determined under laboratory conditions and in compliance with generally approved test regulations in particular DIN standards Technical characteristics can only be warranted to this extent The testing with regard to the qualification and suitability for the client s intended application or the use under service conditions shall be the clients own duty We refuse to grant any warranty with regard thereto Subject to change without notice 39 Glen Dimplex Deutschland GmbH Am Goldenen Feld 18 D 95326 Kulmbach Note on Disposal Email 09221709589 dimplex de Do not dispose of the unit Phone 49 0 9221 709 564 with general household waste Fax 49 0 9221 709 589 The device must be taken to a Internet www dimplex de en local waste disposal 40
9. es in comfort and also in party mode 3 Permanent backlight 6 Display indications If configuring the device for use as floor temperature controller only the time indication is active If the HTRRUu 210 021 has not been configured for use as floor temperature controller the operator can select between the following indications 1 Time 2 Temperature 3 Time amp temperature alternating 32 6 Experts menu Depressing the right touch key and keeping it depressed for 10 seconds after accessing the settings submenu see page 11 from the main menu enables to call the experts menu Caution This menu enables to make control settings that may only be perfor med by a qualified heating specialist or an expert electrician The settings made while operating in this mode cannot be reset via the reset function and have to be made knowingly therefore Clear proof that such settings have been made by one person only is thus ensured The following settings are available 1 Selection of controller configuragtion variants The following controller configuration variants can be selected Room tempera ture controller Room temperature controller with floor temperature controller function or Floor temperature controller 2 Language The operator can select between the following languages Czech Dutch English French German Polish and Russian 3 Measuring correction The measured temperatu
10. ies if no sensor has been connected when using the device as room temperature controller with additional floor monitoring function and also when using it as floor temperature controller An error message appears on the display and an indicator lamp starts blinking red to indicate this condi tion During operation in emergency mode a fixed 30 duty cycle is being maintained to prevent the related room from cooling down thoroughly and protect it against frost damage The activation time divides into a 3 minute ACTIVE and a 7 minute OFF time 3 Operating instructions The device is equipped with 4 touch keys all of which have been marked by the symbol o The functions allocated to them may vary in dependence on the operation requirements The related function is being indicated on the display which exists above the corresponding keys A special protective function helps prevent an inadvertent activation of the touch keys This function is activated 20 seconds after any of the touch keys has last been activated Actuating any of the touch keys deactivates this function again for 2 seconds 4 Control operation CAET 6f Fr 15072011 12 34 Temporary set temperature setting see 41 Selection of the operating mode see 4 2 Main menu see 5 Temporary set temperature setting see 4 1 41 Temporary set temperature setting irs 20 5
11. inst shifting by securing them with one cable tie each as shown here below In so doing care is to be taken to ensure that the distance between cable tie and power supply or sensor line terminal respectively is always kept as short as possible max 15 mm Power supply terminal Sensor line terminal 37 9 Technical data Operating voltage Sensor Switching contact Switching capacity Setting range Switching difference emperature decrease Display Degree of protection Protection class Power reserve Admissible air moisture Storage temperature Ambient temperature Housing colour Housing material Installation mounting 230V 50Hz NTC internal NTC externally connectable type relay make contact 10 2 A 230V 5 30 C control of room temperatures 10 42 C control of floor temperature lt 1K decrease temperature adjustable as follows control of room temperatures 5 29 C control of floor temperatures 10 41 C factory setting 17 C graphic display backlit IP 30 Il after corresponding installation see drawing on page 37 approx 5 days max 95 non condensing 20 70 C 0 35 C pure white pearly white or white similar to RAL 9016 traffic white made of PC PMMA or ABS in an UP box suited for integration into all currently available flush mounted switch frame installation systems 38 10 Accessories
12. m temperature controller with floor temperature controller function or as floor temperature con troller PI PWM method proportional integral recommended for the control of warm water and floor heating systems Two point method hysteresis recommended for the control of electric direct or storage heating systems factory setting two point method 7 External sensor connection possible only when using the device as room temperature controller with floor temperature controller function or as floor tem perature controller The HTRRUu210 021 allows to connect external temperature sensors NTC with resistance values of 2 12 15 or 33kQ The actually used temperature sensor needs to be selected here factory setting 2kQ 8 Reset function Actuating this function resets all settings made outside of the experts menu except for time and date to the condition as delivered 34 7 Mounting connection The device equipped with the 50 x 50 mm housing cover can be integrated into almost all currently available flush switch installation frame systems when using DIN 49075 compliant intermediate frames The device equip ped with the 55 x 55 mm housing is likewise suited for use with different frame systems If using multiple frames the controller needs always to be mounted in the lowest position The controller is determined for installation in an UP box and may not be exposed to any heat or cold sources The con troller mu
13. on of entries returning to the main menu Changing to the display for the entry of comfort and ECO times Weekday onward Weekday Program E E uper Sal Su a End OK 2 25 5 6 Selection of the comfort or ECO times Termination of entries If no changes have been made the system returns to the display for the selection of the weekday Otherwise it changes over to the entry confirmation display ECO time period Position 15 minutes O E E Mo 0015 0030 occ D 1 2 EIECIE SES Position 15 minutes Pal Shifting between comfort or lt Comfort times Factory settings valid from Monday to Friday 05 00 9 00 16 00 22 00 Factory settings valid from Saturday to Sunday 06 00 22 00 26 5 6 Confirmation of entries Termination of entries returning to the weekday selection display Storing of the entries Change to the menu enabling the copying of entries with respect to other weekdays Weekday Program Settings save al 27 5 6 Import of the entries made with regard to other weekdays Selection backward No import of entries returning to the weekday selection display Import of entries with respect to the selected weekday s
14. re value can in dependence on the related configura tion be adjusted with regard to each individual sensor within a range from 5K to 5K at 01K steps At the same time the uncorrected value measured by the rela ted sensor is being indicated on the display factory setting 0 0 4 Maximum temperaturdsetting possible only when using the device as room temperature controller with floor temperature controller function or as floor tem perature controller 33 The maximum temperature measured by the floor temperature can be defined within a range from 15 to 42 C Damages to the floor in consequence of exces sive temperatures can thus be prevented factory setting 42 C 5 Entry of the connected load entry possible only when using the device as room temperature controller with floor temperature controller function or as floor temperature controller In order to allow to compensate the self heating of the HTRRUu the power con sumption of the connected consumer needs to be entered The power consumed in consequence of the connected heating load is indicated in kW and can be adjusted within a range from 0 1 to 2 3 With intermediate values the nearest lower value needs to be set If actuating valves instead of controlling an electric heating system the low power consumption of these valves can be neglected so that no changes need to be made factory setting 0 1 6 Control methods available only when using the device as roo
15. st not be exposed to direct cold or heat sources Furthermore care must be taken to ensure that the device is not exposed to the influence of foreign heat or cold sources that warm or cool the device at its back through air flows in cavity walls or the temperatures radiated by ascending pipelines f ex The controller should be mounted on the wallpaper the wall covering Caution Prior to performing any installation works always make sure to disconnect the mains voltage at all poles The electrical connection is to be realised as shown in the connection diagram in section 8 herein The plug type terminals 1 can comfortably be pre wired for this purpose and connected to the controller while installing it into coco the under plaster box The ope ning of the device is realised as described in the drawing below by holding the housing cover at the top and bottom and pulling it open After first start up the experts menu items 6 2 Language and 6 1 Selection of controller configuration variants are being called up all automatically The device will only be operable after having made correct entries 35 8 Wiring diagram and dimensioned drawing Load max 2 3kW Ext sensor ooooe 36 Important Notice The single wires of both the power supply cable and the sensor line need to protected aga
16. ted to enable the changing of the time at other dates or to meet the time condi tions in other regions 3 Valve and pump protection function The valve and pump protection function serves to prevent the valve seat and or the pump s from corroding up during longer stop times If using the device for the control of warm water heating systems activating the valve protection function is recommended After activation of the valve and pump protection function the controller actuates the valve s or triggers a heating pump every Monday at 11 00 o clock a m over a 5 minute time period The 31 valve and pump protection function is rendered active only if no heating operations were executed within the last week Unnecessary heating during the heating season is thus avoided thereby leaving the control system unaf fected 4 Self learning function The self learning function serves for the autonomous attaining of the comfort temperature at a preset time The antedated point at which the system swit ches from ECO over to comfort temperature sets itself all autonomously Depending on the calorific output and the prevailing outside temperature the heating time will vary 5 Backlighting of the display The length of time during which the display backlight is on can be selected as follows 1 Backlight during operation plus 10 seconds after the last actuation of any of the touch keys 2 Additional backlight during operating tim
17. y on which holidays begin Month in which holidays begin 1 Holiday from Month ui 14 12 End a 13 5 2 Entry of the day on which holidays begin Holiday from i 14 1 Day on which holidays begin 1 Termination of the entry returning to the main menu Changing over to the month in which lt holidays end Day on which holidays begin 1 14 5 2 Entry of the day on which holidays end Holiday until A Month iii 15 12 BEK a Day on which holidays end 1 Termination of the entry returning to the main menu Changing over to the day on which holidays end Day on which holidays end 1 15 5 2 Entry of the day on which holidays end Holiday until ian 1512 GENE a Day on which holidays end 1 Termination of the entry returning to the main menu Changing over to the holidays temperature menu Day on which holidays end 1 16 5 2 Entry of the holiday temperature Holiday temperature 0 5K Termination of entries returning to the main menu Import of all values returning to the main menu Holiday temperature 0 5K
Download Pdf Manuals
Related Search