Operating Instructions
Contents
1. E130 Speed too high Pot not in Pot not out Machine status e The container is clamped e The container is not clamped e Latching pin blocked e Latching pin released e Latching pin blocked e Latching pin released e The mixing unit rotates e The mixing unit does not rotate e Slide has been moved in e Slide is out e Slide is in e Slide has been moved out Collomix R hr und Mischger te GmbH D 85080 Gaimersheim Items to remedy actions to take e check clamping motor brushes and control pcb e The mixing unit is not at 12 o clock position move by hand e Check whether the clamping table clamping table switch moves smoothly e Check the lead connector to the clamping proximity switch e The latching pin is blocked clean and lubricate replace if necessary e Check the lead connector to the switch of the mixing unit magnet e The switch of the mixing unit magnet is defective e The mixing unit is not 12 at o clock position move by hand e Check the lead connector to the switch of the mixing unit magnet e The switch of the mixing unit magnet is defective e The latching pin is blocked clean and lubricate replace if necessary e Check the lead connector to the mixing unit magnet e The mixing unit magnet is defective e Check the lead connector to the position proximity switch e The position proximity switch is defective e Check the fuse for SI 2 motor e Check the lead conn2. Maintenance technician Cleaning the machine Clean the inside and the outside of the machine D Remove paint residues from the spindle and the spindle shaft with a steel brush EN Remove paint residues from between the upper clamping table and the clamping table carrier Inspections Check the drive belt for wear and tension NEM Check that the latching pin on the mixing unit magnet moves smoothly VE Check that the slide with the clamping table moves smoothly Remove any dirt EE Check all ball bearings to see that they move smoothly There are ball bearings on the slide pull out the two clamping jaws the transmission drive shaft and the clamping tables Check the state of wear of the carbon brushes They should have a minimum length of approximately 9 mm Lubricating the machine Check the amount of PERMA lubricant if necessary replace the cartridge EE Lubricate the threaded spindles and he spine shaft with MOLKOTEBR2 Brush a itl lubriccing ol on the guide columns ofthe mining uni Miscellaneous Replace the fuses on the pcb S1 S2 6 3 AT 250V S3 4 0 AT 250V use only sand filled flow fuses Add more spare fuses as required NENNEN Carry out a function test with a large and a small container Comments IEEE MM 16 Edition G 1 1 10 Collomix R hr und Mischger te Gmbh B ax 44S 44SX D 85080 Gaimersheim 7 5 Layout of the main board 1133 LP 191201 A4 XX XX 230V Mixer Mo
3. date of installation on the cartridge The lubrication is guaranteed for approx year Please read the accompanying original PERMA documentation 4 4 Trial run It is best to carry out a trial run with an empty mixing container when you are starting up the machine for the first time or after carrying out maintenance work or repairs Remove all tools and any other loose items from the inside of the machine If the machine wobbles while it is working adjust the machine feet to compensate the differences in height It is prohibited to operate the machine on its shipment pallet 8 Edition G 1 1 10 PERMA lubrication Collomix R hr und Mischger te Gmbh D 85080 Gaimersheim 5 Operation 5 1 Switching on the machine The machine is switched on with the main switch 3 After initialisation has been completed the door can be opened and the slide be automatically moved out by pressing button E The machine is now in its starting position ready for mixing 5 2 Moving slide to parking position When the machine is not used or before switching off the machine after work the slide can be moved into its parking position by pressing buttons E and I simultaneously The slide is moved in and the door is closed 5 3 Moving Slide to starting position By pressing button E the slide can be moved from its parking position to its starting position The door is opened and the slide moved out The display indicates READY
4. the machine is ready for mixing Edition G 1 1 10 BiAx 44S 44SX Collomix BIAX init Version X XX Collomix BIAX init d 80 c 25 v 144 v v Collomix BIAX init 000011 cycles v Collomix BIAX init gt Press E to quit A 9 Collomix BIAX init opening door Collomix BIAX init moving pot out Ready 1 00 Ready 1 00 2 00 3 00 gt Parkposition closing door Parkposition moving pot in Parkposition press E for Ready Parkposition press E for Ready Parkposition opening door Parkposition moving pot out i i j il Ready 1 00 2 00 3 00 B ax 44S 44SX Collomix RUhr und Mischgerate GmbH 5 4 Loading the container If the mixing container is higher than the position of the clamping table press button E to widen the mixing unit Secure the container handle with a rubber band or adhesive tape and place the mixing container on the mixing table in central position Do not use damaged containers or place containers on top of each other It is also possible to mix several identical containers simultaneously In this case make sure the containers are placed on the clamping table in a symmetrical arrangement Place container in central position 5 5 Mischvorgang starten Start the mixing cycle by pressing one of the timer buttons I II or Ill The corresponding mixing time is indicated in the LCD display above the buttons The slide is moved
5. the housing These transport rollers can be made to protrude out of the mixing compartment by turning two screws in the base plate of the mixing compartment Before moving the ROTA 20 30 you must remove the door To do so simply pull out the two hinge pins e Use a cordless screwdriver counter clockwise rotation or some other suitable tool size SW 17 to turn out the transport rollers on both sides of the machine e Carefully tilt the mixer and move it e When you are finished moving the machine turn the transport rollers back in and compensate any unevenness with the height adjustable feet Screw Turning out the rollers gt Moving the machine It is necessary to open the door in order to be able to firmly grip A the machine during transport Edition G 1 1 10 7 B ax 44S 44SX Collomix RUhr und Mischgerate GmbH D 85080 Gaimersheim 4 3 Activating the PERMA lubrication system The machine comes with a PERMA long time lubricator which is to be installed before you use the machine for the first time Proceed as follows For an easier installation first open the mixing unit completely The lubrication nipple on the hub is on the right side Activate the PERMA cartridge by turning the grey activation screw into the cartridge until the holding clip is torn off completely Remove also the black cap at the top of the cartridge Screw the cartridge into the adapter which was fitted to the hub at the factory Write the
6. GENCY STOP function ccccceeceececcsccsecsceseeeeees 11 6 Tro ble shool Hg ioo ii oed eek 12 621 ntialzahon 22 PITT ee 12 0 2 Error messe S orn ke ern 13 7 Maintenance and cleaning essescesceccecoecoecoecoecoecoecoecsecsecsecsecsoesoesoe 15 Zele odore lol PNE E esereidenie 15 7 2 GIG cect cases nates tcc ME MINI MI DE 15 7 9 MMEO NC Eiei a a e r a E 15 74 Maintenance checklist s ouo oe 0 kan 16 7 95 Layout orihe main board aoo ni is 17 7 6 Layout of theextension board 18 MM ode Tee 19 8 1 Technical prelio PEE EE au 19 9 2 W attalilyiei cesis es ee Rated iu cU EP dees 19 8 3 Recycling and disposal eisrean tea 20 8 4 Declaration of CE conformity cieee E aR 20 2 Edition G 1 1 10 Collomix R hr und Mischger te GmbH D 85080 Gaimersheim Collomix R hr und Mischger te Gmbh BiAx 44S 44SX D 85080 Gaimersheim 1 Layout drawings 1 1 Machine components 6 7 1 Machine components 1 Threaded slide spindle 5 Emergency Stop 2 Top clamping table 6 Automatic sliding door 3 Main switch 7 Slide with clamping table 4 Control panel Edition G 1 1 10 3 B ax 44S 44SX Collomix RUhr und Mischgerate GmbH D 85080 Gaimersheim 1 2 Control and display components 11 Collomix 10 10 Control buttons e OPEN the mixing unit e QUIT stand by mode Q Button E e STOP mixing cycle prematurely e ACKNOWLEDGE messages e MOVING Slide out Button e Mixing cycle works
7. Operating Instructions Biaxialmixer BIAX 44S 44SX GB Englisch Edition G 1 1 10 BiAx 44S 44SX Contents 1 L yool drawings oor Vieh nern 3 1 1 Maechinescompohenlsu e epu e rat Rue 3 1 2 Control and display components eeeeeeeeeee e 4 2 General information a aeo ETUR een 5 Se For your safely unsere 5 3 1 Pictograms and symbols used in this manual ccccscceeceececeeeeeees 5 8 2 PODE USB ern ON RO Re M M M ela ee re 5 3 3 General safety instructions ccssccsscsscescsseneceesssscaecsccesssscnecesseaess 6 3 4 Safely relevant comporenlis e soo ove eerte art ete ea 6 4 Using the machine for the first time ee eee eee eee ee eee ee eee ene 7 4 1 Installing the machine Transport notes ccccececceceeceecsceeceeeeeeeesees 7 4 2 Moving ine machine 7 4 3 Activating the PERMA lubrication system ccsccececcecceeceeeeseeeeecaeenes 8 24 Trial TUE seta asien 8 9 ODOFGllOn o ascesesteseessetetenenete eA vasa eva E eben en eae e e T VAR NS SEVA FR S e etes neue aua 9 5 le Switching on The machine un 9 5 2 Moving slide to parking position cccceccecnecscceceecscceceecsececeeceeseeeeees 9 5 3 MOVING Slide to starting position eere see 9 5 4 LOGGING The container nur se an 10 5 9 MISChVorgang starten uni 10 5 6 Ending Ihe mixing cycle u a rone mee eit 10 9 7 Standby seele ee 11 5 8 Triggering the EME
8. d e The door is open e There is no container in the mixing unit e A container is loaded in the mixing unit e The threaded spindles are dirty e The mixing unit is fully open e The mixing unit is not fully open e The container is defective e The container is not defective Edition G 1 1 10 Items to remedy actions to take Press button E to cancel stand by mode Check the Door open proximity switch Check the extension board Check the door motor Check the extension board Release the EMERGENCY STOP Check the EMERGENCY STOP switching element Check the lead connector to the EMERGENCY STOP Check the Door closed proximity switch Check the extension board Check the door motor Check the extension board Load a container The container is too small Check the clamping table switch Check the programmable cam Clean and lubricate the threaded spindles Note that the maximum container height is 400mm Clean and lubricate the threaded spindles Clean and lubricate the guide columns Press button P to reinitialize the machine Correct the clamping pressure Check whether the clamping table clamping table switch moves smoothly Check the lead connector to the clamping proximity switch The clamping proximity switch programmable cam clamping table microswitch or control pcb is defective 13 BiAx 44S 44SX Fault E060 not disclamped E070 MU locked E080 MU unlocked E120 Speed too low
9. e press BUTTON E Ready 1 00 2 00 3 00 5 8 Triggering the EMEGENCY STOP function E020 emergency stop unlock switch N You can press the Emergency Stop button to switch off the machine if ever the container develops a leak or its handle becomes loose or some other potentially NOT AUS Entriegeln dangerous situation for man or machine arises while the mixing cycle is in progress After the EMERGENCY STOP button is pressed the mixing unit will coast to a standstill and remain in this position The mixing unit is not moved automatically to the 12 o clock position Unlock the EMERGENCY STOP button by hand and press button E to cancel the error message E020 emergency stop gt press E to quit After the door has been opened rotate the mixing unit by hand until it is locked in id E020 emergency stop the 12 o clock position wait Unclamp the mixing unit by pressing button E the slide is moved out automatically and the container can be removed E020 emergency stop 3 M gt press E to quit The machine is in base position mixing can be continued E020 emergency stop opening door please disclamp gt press E to quit The EMERGENCY STOP button does not oP disconnect the machine from the mains power t supply Therefore before performing any maintenance work or repairs always be sure to disconnect the machine from the mains by Mischsinheit per pulling out the power plug Hand positionieren We B 7
10. e control pcb Check the connector cable of the display pcb The display is defective The control pcb is defective EMERGENCY STOP actuated Check the connector cable of the EMERGENCY STOP EMERGENCY STOP switching element is defective Container already clamped unclamp by hand The mixing unit is not in the 12 o clock position Check the clamping table proximity switch Check the connector cable of the clamping table proximity switch Latching pin blocked Check the connector cable of the mixing unit magnet The mixing unit magnet is defective The mixing unit is not in the 12 o clock position Edition G 1 1 10 Collomix R hr und Mischger te Gmbh D 85080 Gaimersheim 6 2 Error messages BiAx 44S 44SX The following table provides an overview of possible errors and their remedies Please note that all maintenance and servicing jobs must be left strictly to authorized and suitably trained personnel This applies in particular to those jobs printed on a gray background which have to be performed with the housing open Fault E000 Stand by E010 door not open E020 Emergency stop E025 door not closed E030 Pot not found E040 Max open E050 Pot defective Machine status e 60 minutes have passed without the user actuating any function the machine is in stand by mode e The door has been opened e The door is closed e EMERGENCY STOP actuated e EMERGENCY STOP not actuated e The door has been close
11. e machine Keep this manual within immediate reach of the machine 3 1 Pictograms and symbols used in this manual The caution symbol is used to indicate a situation in which persons are at risk of suffering physical injury The warning must be heeded at all costs The stop symbol is used to indicate a situation in which the machine is at risk of being damaged The hazardous electric voltage symbol is used to indicate live components that may pose a risk to life and limb Those parts of the manual that are important for the correct and safe operation of the machine are printed in bold type 3 2 Proper use The machine must not be operated in any way other than described in this manual The term improper use applies in particular to the following e Operation with defective or missing parts e The bridging or deactivation of any safety devices e Operation of the machine in areas with a potentially explosive atmosphere e The use and installation of non original replacement parts e Running the machine for too long which can potentially lead to the mixing container bursting The consequences of improper use can be personal injury to the user or third party as well as material damages to the appliance or mixing material Edition G 1 1 10 BiAx 44S 44SX B ax 44S 44SX Collomix RUhr und Mischgerate GmbH 3 3 General safety instructions Observe the electrical regulations in force as well as the add
12. ector to the motor e The motor rectifier or control pcb is defective e Decrease the motor speed e Check the proximity switch slide e Check the extension board e Clean and lubricate the threaded spindle e Check the slide motor e Check the extension board e Clean and lubricate the threaded spindle e Check the slide motor e Check the extension board e Check the proximity switch slide e Check the extension board The actions printed on a gray background have to be performed by authorized and suitably trained personnel 14 Edition G 1 1 10 Collomix R hr und Mischger te Gmbh BiAx 44S 44SX D 85080 Gaimersheim 7 Maintenance and cleaning Regular maintenance is necessary to ensure that the machine remains in good working condition at all times If the machine is in constant use it is important to lubricate the most important parts in accordance with the schedule described below How often you repeat the maintenance depends on how long the machine is operated Always pull out the power plug before carrying out any maintenance work 7 1 Inspections Check all safety relevant parts of the machine before beginning with your work Arrange for authorized personnel to replace defective or damaged parts before you work again with the machine 7 2 Cleaning If any material escapes from the mixing container when it is inside the machine remove it immediately Use a rag or a spatula Take care not to damage any co
13. ecycling and disposal The transport packaging consists of recyclable material Please dispose of it accordingly At the end of the machine s working life the materials used in its construction must be properly recycled If you have any questions concerning the disposal of any materials please contact the manufacturer 8 4 Declaration of CE conformity We declare herewith that this product conforms with the following standards and standard setting documents DIN EN ISO 12100 1 DIN EN ISO EN 12100 2 DIN EN ISO 954 1 DIN EN ISO 14121 1 DIN EN 55011 DIN EN 61000 6 2 DIN EN 61000 4 2 DIN EN 61000 4 3 DIN EN 61000 4 4 DIN EN 61000 4 5 in accordance with the provisions of directives 2006 95 EEC 2004 108 EC 2006 42 EC Technical file at Collomix R hr und Mischger te GmbH Abt Technische Entwicklung Daimlerstr 9 85080 Gaimersheim Germany Gaimersheim 29 12 2009 hs Alexander Essing General Manager Manvfacturer Collomix R hr und Mischger te GmbH Daimlerstr 9 D 85080 Gaimersheim Federal Republic of Germany Tel 49 0 8458 32 98 O Fax 49 0 8458 32 98 30 This declaration of conformity will lose its validity if any changes or modifications are made to the machine without the manufacturer s approval 20 Edition G 1 1 10 Collomix R hr und Mischger te Gmbh B ax 44S 44SX D 85080 Gaimersheim Edition G 1 1 10 21 BiAx 44S 44SX 22 Edition G 1 1 10 Collomix RUhr und Mischg
14. erate GmbH D 85080 Gaimersheim Collomix R hr und Mischger te Gmbh B ax 44S 44SX D 85080 Gaimersheim Edition G 1 1 10 23 BiAx 44S 44SX Collomix RUhr und Mischgerate GmbH Collomix RUhr und Mischger te GmbH Daimlerstr 9 D 85080 Gaimersheim Federal Republic of Germany Tel 49 0 8458 32 98 O Fax 49 0 8458 32 98 30 D 85080 Gaimersheim
15. i disclamping moving pot out Hi j Ready 1 00 2 00 3 00 uli Edition G 1 1 10 BiAx 44S 44SX 6 Trouble shooting Collomix RUhr und Mischgerate GmbH D 85080 Gaimersheim Using the trouble shooting tables listed in this chapter you can check whether you are able to correct the errors yourself or whether you need to call the customer service department number the error code being shown in the display and also the status of the LEDs on the control Y Before calling the customer service department please make a note of the machine s serial panel The machine s serial number can be found on the machine s rating plate 9 6 1 Initialization Initialization is performed each time the mixer is switched on The following error messages may appear as a result Please note that all maintenance and servicing jobs must be left strictly to authorized and suitably trained personnel LEDs Display 230 V O 24V O empty 230 V 6 24V 6 empty 230 V E020 emergency stop 24V gt press E to quit 230 V E060 not disclamped 24V gt press E to quit 230 V E080 MU unlocked 24V 6 gt press E to quit All maintenance and servicing jobs must be left strictly to authorized and suitably trained personnel This applies in particular to work performed with the housing open 12 Items to remedy actions to take Check the power supply Check the SI 3 fuse Check the connector cable of th
16. in automatically and the doors close The mixing container is clamped in place and the mixing cycle is started automatically The remaining mixing time is indicated in the LCD display as the mixing cycle progresses 5 6 Ending the mixing cycle The mixing unit is automatically moved to the 12 o clock position and the clamping pressure released when the mixing time is over You can end the mixing cycle prematurely before the mixing time is over by pressing button E The mixing cycle is immediately ended the mixing unit positioned the clamping pressure released and the door unlocked After the mixing cycle has been finished the door will open automatically and the slide will be moved out Important When you have finished using the machine be sure to switch it off with the main switch 10 Edition G 1 1 10 D 85080 Gaimersheim Securing the handle with a rubber band Ready 1 00 2 00 3 00 v v Mixing t 1 00 clamping v Mixing t 1 00 Pot clampt v Mixing t 0 59 mixing wait v Mixing t 0 00 unclamping v Ready 1 00 2 00 3 00 Collomix R hr und Mischger te Gmbh B ax 44S 44SX D 85080 Gaimersheim 5 7 Stand by E 000 Stand by gt press E to quit If approximately 60 minutes pass without the user actuating any function the biaxial mixer will automatically switch to stand by mode All unnecessary consumers are switched off and the door can no longer be opened ei To quit stand by mod
17. is deactivated the latching pin is pushed back by spring force and releases the mixing unit Clamping table switch A microswitch on the upper clamping table monitors whether a container is clamped in the mixing unit It is impossible to start the mixing cycle when no container is clamped in place For the switch to trigger a switching pulse it has to be pressed up by the spring mounted upper clamping table Emergency Stop function With the Emergency Stop function you can e reliably interrupt the control voltage supply so that the machine is unable to move e bring the machine to a halt when it is running 6 Edition G 1 1 10 D 85080 Gaimersheim Collomix R hr und Mischger te Gmbh B ax 44S 44SX D 85080 Gaimersheim 4 Using the machine for the first time 4 1 Installing the machine Transport notes Your biaxial mixer is delivered in reusable cardboard packaging on a wooden pallet Please immediately check the packaging when received as well as the appliance during unpacking for any visible signs of external damage Keep all parts of the original packaging for any necessary return transport Use a suitable hoist to lift the machine off the pallet Fit the door handle with the supplied mounting materials Place the machine on firm level ground Slight unevenness can be compensated with the height adjustable machine feet SW17 19 4 2 Moving the machine The mixer has two transport rollers on the bottom of
18. itional instructions listed in this manual when you install the machine Installation and use of the machine for the first time must be carried out by a trained specialist The machine is to be used only by persons who are acquainted with the working principles of the machine and also with the safety and accident prevention regulations in force in your country i T Check that the machine is in the proper condition and that all parts XY F are in good working order before beginning with your work Do not operate the machine with any defective or missing parts Any maintenance work or repairs must only be carried out by qualified personnel Before performing any maintenance work or repairs be sure to disconnect the machine from the power supply by pulling out the power plug Use only original replacement parts Close the machine when not in use and turn off at the main switch Projecting parts may injure you and others 3 4 Safety relevant components Closed housing The housing is a stationary safeguard and partition that can only be opened with the use of tools Machine door with interlock The door is an interlocking safeguard and partition It is impossible to start the machine when the door is open The door is not unlocked until after the mixing cycle is ended and the mixing container released Latching magnet for the mixing unit The mixing unit is locked in vertical position by a magnetically actuated latching pin When the magnet
19. nnecting leads or sensors Dirty threaded spindles can be cleaned with a rag or a wire brush When you have finished cleaning the threaded spindles lubricate them again with Molycote BR 2 Plus Important Never clean the machine with a high pressure cleaner or the like This could wash the lubricating grease out of the ball bearings leaving them to run dry This will result in serious damage Ball bearings which have run dry must be replaced immediately 7 3 Maintenance Every week e Remove any dirt from the machine e Apply a thin coat of lubricating oil at the two guide columns of the mixing unit Every 6 months e Check the PERMA lubricating cartridge 2 and replace it when necessary e Lubricate the threaded spindle 4 threaded slide spindle 5 and the spindle shaft with Molykote BR 2 plus e Check that the lock pin at the mixing unit magnet moves smoothly e Check that the slide 3 moves smoothly remove any dirth and lubricate lightly with oil e Check that all ball bearings move smoothly Ball bearings are to be found on the two clamping jaws on the drive shaft at the transmission gear and on the clamping tables 1 Guide columns 2 PERMA cartridge 3 Slide pull out mechanism 4 threaded spindle 5 Locking lever Edition G 1 1 10 15 B ax 44S 44SX Collomix RUhr und Mischgerate GmbH D 85080 Gaimersheim 7 4 Maintenance checklist Maintenance checklist for BIAX 44S BIAX 44SX Location of the machine
20. on G 1 1 10 Collomix RUhr und Mischgerate GmbH D 85080 Gaimersheim gig ST5 ST4 TEE EE 3 6 paan 7 EDER LD17 imi LD15 213141516 Collomix R hr und Mischger te Gmbh D 85080 Gaimersheim 8 Annex 8 1 Technical data Type of machine BiAx 44 S B ax 44 SX Supply voltage 1 N PE 3 N PE 230 Volt 50 Hz 400 Volt 50 Hz Rated power 1 1 kW 2 2 kW Fuse 16A 16A Speed mixing unit max 170 UpM max 200 UpM Max container weight 40 kg container height 110 450 mm Max container base area 365 mm Machine weight 235 kg 235 kg Dimensions w x d x h 830 x 857 x 1112 mm 8 2 Warranty The manvfacturer undertakes to provide as part of the general terms of supply and delivery a twelve month warranty This warranty applies to single shift operation and is counted from the date of initial start up It covers all defects arising from faulty material or workmanship Please note that all warranty claims must be accompanied by the original delivery note or initial start up report All essential warranty repair work must only be carried out by adequately trained service engineers or by third parties with express prior authorization from Collomix The carrying out of unauthorized repairs may render the warranty null and void Please return any defective parts or machines carriage paid to our factory Collomix reserves the right to decide on whether cost free parts replacement is applicable Par
21. setting 1 00 minutes Button ll Mixing cycle II works setting 2 00 minutes ur Button Ill Mixing cycle Ill works setting 3 00 minutes e MOVING Slide in Parking Position 11 Display for 230V mains voltage and 24V control voltage 12 LCD Display 13 EMERGENCY STOP button 4 Edition G 1 1 10 Collomix R hr und Mischger te Gmbh D 85080 Gaimersheim 2 General information The BIAX is a stationary mixer for closed tightly closing round rectangular and oval containers made of metal or plastic It can be used to mix paints master batches house paints industrial paints and plasters as well as other low viscosity materials Practical applications are to be found in the wholesale and retail paint trade in the paint lacquer and chemical industries and many other related sectors This shaker is particularly ideal as a component in paint dosing systems The clamped container rotates simultaneously about its longitudinal and transverse axis at 2 different speeds which are adapted to the material in question The required mixing time and the suitability of the container are to be determined before attempting to use the shaker This manual is intended for persons who operate the machine 3 For your safety Although the machine has been developed manufactured and tested in accordance with fundamental safety requirements an element of risk is still present Therefore read this manual before you work with th
22. tor 230V primary transformer and electronics Fuses No Valve Function Lead Function SI 6 3AT 24V fuse Mixing unit magnet Mixing unit magnet switch 6 3A T 230V mixer motor I3 S 4 0A T 230V primary transformer electronics Connector assignment ST 1 Lead Function MIOISH 24V AC from transformer ST3 Lead SEES me Function blue Clamp motor Jumper assignment ST2 4 N STS Joen Gr n gelb PE 1 2 BIAX 44SX 2 3 BIAX 44S ST 8 1 2 Service 2 3 Operation Emergency stop extension ST21 1 2 BIAX 44SX 2 3 BIAX 44S board LED signals l Emergency stop Display meaning Clamp proximity switch BIS Lead Funcion Position proximity switch Mixing unit magnet switch door closed roximity switch door closed E 2 1 not by BIAX 44SX 2 only by Biax 44SX Edition G 1 1 10 17 BiAx 44S 44SX 7 6 Layout of the extension board LD30 LD29 ST 9 TEEDEISEIS S Fuses No Value Function 6 3AT 24 V Fuse Connector assignment 24V AC from transformer ST2 Lead Function LO Slip ring slide motor ST3 Lead Function Emergency stop ma n board ST Lead Proximity switch slide 3 bue LED signals Display Meaning SS Proximity switch slide LED signals sr10 18 Editi
23. ts and labor covered by the warranty will be supplied free of charge The warranty does not cover travel costs expenses or possible overnight accommodation resulting from warranty repairs carried out off our premises Any further responsibility with particular reference to damage claims including foregone profit or other material losses on the part of the customer is expressly excluded Warranty and liability claims for personal or material damages are excluded if attributable to one or more of the following causes e Incorrect operation of the machine as defined in the operating instructions e Failure to observe the instructions in the operating manual with respect to set up initial start up operation and maintenance of the machine e Faults or damage caused by excessive accumulations of dirt and or incorrect cleaning schedules with particular reference to leaks and damaged containers e Operation of the machine with defective safety and or protection devices e Unauthorized structural modifications to the machine e Incorrect monitoring of parts subject to wear and consumables e Unauthorized repairs and or the fitting of non original spare parts e Damage caused by the impact of foreign bodies or force majeure e We reserve the right to make amendments as a result of ongoing advances in the technical field Edition G 1 1 10 BiAx 44S 44SX 19 B ax 44S 44SX Collomix RUhr und Mischgerate GmbH D 85080 Gaimersheim 8 3 R
Download Pdf Manuals
Related Search