EN DE Original-Montage- und Betriebsanleitung Original assembly
Contents
1. GJ5603ke GJ5606ke GJ5610e GJ5618e Voltage 230 V 50 Hz Current 0 40A 0 40A 0 60A 0 80A Cos Phi coso gt 0 95 Inrush current factor x 1 2 Power 90 W 93 W 135 W 180 W Torque 3 Nm 6 Nm 10 Nm 2 x 9 Nm Speed 26 rpm Protection class IP 54 Limit switch range 200 rotations Operating mode S2 4 min Sound pressure level 34 db A 34 db A 35 db A 40 db A Length 301 mm 301 mm 311 mm 338 mm Diameter 55 mm Weight approx 1 50 kg approx 1 50 kg approx 1 70 kg approx 2 20 kg Ambient temperature Operation T 10 C 60 C H max 90 humidity Storage T 15 C 70 C dry and non condensing place Subject to technical modifications CEASA Technical data GJ56 e with electronic end stop run time optimized version GJ5606e GJ5616e Voltage 230 V 50 Hz Current 0 40A 0 70A Cos Phi coso gt 0 95 Inrush current factor x 1 2 Power 90 W 150 W Torque 6 Nm 2x8Nm Speed 26 rpm Protection class IP 54 Limit switch range 200 rotations Operating mode S2 6 min Sound pressure level 34 db A 40 db A Length 306 mm 338 mm Diameter 55 mm Weight approx 1 60 kg approx 2 20 kg Ambient temperature Operation T 10 C 60 C H max 90 humidity Storage T 15 C 70 C dry and non condensing place 1 The average sound pressure level data are intended for guidance only The values were determined by GEIGER at a distance of 1 m with a hanging motor at idle speed and a2. Antriebstechnik Venetian blind motor GEIGER GJ56 e with electronic end stop For Venetian blinds and exterior blinds Original assembly and sapia t EN operating instructions EN Index 1 General information ccceeceeeeceeeeeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeees 2 25 GUALAMMCE ia ies icvctssevcs E E ETT 2 33 Intended US raaa aaea araa r araa rae daaa eaat Eaa 2 4 Safety INSTI HONS wis scuceiera eieeasniesacnnainnvennantevediecanivnignecivindartin inane 3 5 Safety instructions for assembly ccccceeeeeeseeeeeeeeeeeeenees 3 6 Assembly NOC vcscsini sve cinrsesineesiniduccnsveteeieesrieverteatnsenseisinavedaiens 4 7 Installation instructions cccccceeeseeseneeeeeeeeeeeeeeeeeeeeeeeeeeneenes 5 8 Information for the specialist electrician 2 0 05 6 9 Control features n s cassueurticcsteesans ener cedanvendedwacatinsiinceaniecinaavartan 6 10 Setting of the end StOPS sssssssnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnna 7 11 OPO atlOn ss iaceces cs divcwieclecersecaccestvevdedacepiecwicecevesseectiwevscecsversexeucses 9 12 What tO GO ifisi aeeoea e raaa aaa anaran aaar a aa a aaeocae aont 9 13 Mainte anC escribans aaeain aa anaua adi sadna a daraan d anana 9 14 Technical data ccetcictecceicetecdececcesesisetcedeececcstertecesereeccebeseuvetsrets 10 15 Declaration of conformity sssssseneeennnnnnnnnennnnnnnnnnnnnnnnnnnnnn 11 16 Notes on waste disposal
3. ssssssssssssssnusnuuennnnnnnnnnnnnnnnnnnnnnnnn 12 1 General information Dear customer By purchasing a GEIGER motor you have decided on a quality product from GEIGER Thank you very much for your decision and the confidence placed in us Before you put this drive into operation please observe the following safety instructions It serves for the prevention of danger and for the avoidance of personal injury and damage to property The installation and operating instructions contain important information for the installer the specialist electrician and the user Please pass on these instructions if you transfer the product These instructions should be kept by the user 2 Guarantee In the case of incorrect installation contrary to the installation and operating instructions and or constructional modification the legal and contractual guarantee for property damage and product liability lapses 3 Intended use The motors of the model range GJ56 e with electronic end stop are designed exclusively for the operation of Venetian blinds The motors may not be used for the operation of roller grilles garage doors furniture and lifting tools GJ 56 xx x Design options Torque in Nm For head rails at least 56 mm GEIGER Venetian blinds motor 2 EN Gerhard Geiger GmbH amp Co KG 100W1503en V001 1214 4 Safety instructions ATTENTION Important safety instructions For personal safety it is important to follow these instructio
4. then release the programming button 7 Setting of the upper end position press the direction keys to exactly run the GJ56 e to the desired upper end position 8 Press the programming button till the LED keeps lighting The adjustment procedure is completed www geiger de EN 7 EN Setting GJ56 e4 The order of the adjustment process must be strictly adhered to and the adjustment must always be completely implemented all steps The motor GJ56 e4 is set up with a learning mode During assembly please begin the setting with step 1 and then go over to step 7 Connect the setting switch to the GJ56 e and then plug in power supply Press the programming button till the LED flashes 1 flash light break 1 flash light break then release the programming button Setting of the lower end position press the direction keys to exactly run the GJ56 e to the desired lower end position Press the programming button till the LED flashes 2 flash lights break 2 flash lights break then release the programming button Setting of the shade position press the direction keys to exactly run the GJ56 e to the desired position Press the programming button till the LED flashes 3 flash lights break 3 flash lights break then release the programming button Run the blind to the upper end position The motor turns off via torque recognition Press the programming button till the LED ke
5. the operation points 3 5 and 7 the end stops have kept the same position as before Shade position working position only e1 e4 The shade position working position can be reached by actuating both direction keys at the same time Overload recognition The overload recognition is adapted to the given torque safety margin of the Venetian blind system by carrying out the complete adjustment procedure The blind must be moved by steps 3 5 and 7 Setting GJ56 e1 e2 and e3 The order of the adjustment process must be strictly adhered to and the adjustment must always be completely implemented all steps The motor GJ56 e3 is set up with a learning mode During assembly please begin the setting with step 1 and then go over to step 7 Connect the setting switch to the GJ56 e and then plug in power supply 2 Press the programming button till the LED flashes 1 flash light break 1 flash light EN break then release the programming button 3 Setting of the lower end stop press the direction keys to exactly run the GJ56 e to the desired lower end position 4 Press the programming button till the LED flashes 2 flash lights break 2 flash lights break then release the programming button 5 Setting of the shade position working position press the direction keys to exactly run the GJ56 e to the desired position 6 Press the programming button till the LED flashes 3 flash lights break 3 flash lights break
6. 8 m gt Ifthe motor is controlled by a switch or pushbutton the switch or pushbutton must be mounted within eyeshot of the motor The switch or pushbutton must not be located in the vicinity of moving parts The height of installation must be at least 1 5 m above the floor gt Permanently installed control devices must be attached visibly gt In case of devices extending horizontally a horizontal distance of at least 0 4 m must be respected between the fully extended part and any other fixed element www geiger de EN 3 EN EN The rated speed and the rated torque of the motor must be compatible with the device The mounting accessories that are used must be designed in accordance with the selected rated torque Good technical knowledge and good mechanical skills are necessary for the motor installation Incorrect installation can lead to serious injury Electrical work must be carried out by a qualified electrician in accordance with the regulations in force locally Only use connecting cables that are suitable with the environmental conditions and which meet the construction requirements see accessories catalogue If the device is not equipped with a connecting cable and a plug or other means for disconnecting from the mains with a contact opening on each pole according to the conditions of the overvoltage category Ill for full disconnection a disconnecting device of this type must be incorporated into the permanently inst
7. Please follow all installation instructions since incorrect installation can lead to N the destruction of the motor and the PE switching unit e1 e4 the setting of the end stops requires a GEIGER l setting switch l e5 the setting can be realized with any switch allowing i simultaneous UP and DOWN controls e1 e4 a non locking switch series switch is needed in order to reach the shade position See point 10 Opera tion e5 a locking switch is here necessary no simultaneous UP and DOWN commands The operations with the service clamps may be accom plished only by an electrical specialist Motors with electronic limit stops can be connected in z parallel In this case the maximum load of the switching unit must not be exceeded When changing the running direction the switchover must l be effected through an off position l When changing the running direction the switchover time i must be at least 0 5 s l l pe Electronic mechanical limit stop With a three phase network please use the same external conductor in order to control the UP and DOWN directions Connecting cables with plug connectors of the Hirschmann Company are tested and approved with couplings of the Hirschmann Company In order to prevent a malfunction caused by coupling the supply line ref NYM from the actuator switch to the motor must not exceed 100m in case of motors with electronic end stops EN 9 Control fe
8. alled electrical installation according to the wiring rules Do not mount the connecting cables near hot surfaces A plug for the disconnection of the motor from the power supply must be accessible after installation Damaged connecting cables must be replaced by GEIGER connecting cables of the same type The device must be mounted as described in the installation instructions Fixations shall not be made with adhesives since they are regarded as unreliable 6 Assembly note When viewed from inside the room the Electric mains power supply connection of the GJ56 e is located on the left side The straps are wound on the winding rollers from the Direction OPEN outside The GJ56 e must be installed in align ment with the turning bars It is important that the GJ56 e is installed centrally Please make sure that the load is evenly distributed Inclined installation The inclined installation is permitted till 45 maximum to level y b y i Inside the room LAA Af Bee 4 EN Gerhard Geiger GmbH amp Co KG 100W1503en V001 1214 7 Installation instructions Prior to installation please check to ensure there is no visible damage to the motor like cracks or open cables Before fixing please check the strength of the masonry and of the surface kf EN 5 www geiger de 8 Information for the specialist electrician Caution Important installation instructions Mains 230V 50Hz
9. angers Children are not permitted to play with the device Cleaning and maintenance should not be carried out by children gt The rated sound pressure level is less than 70 dB A gt Disconnect the device from the mains power supply for maintenance and replace ment of parts If the motor is disconnected via a plug connection the operator must be able to control from any place to which it has access that the plug is removed If this is not possible due to design or installation the disconnection from the v vvvvv vyv power supply must be ensured via locking in the disconnected position e g isolator gt The motor tube can get very hot during prolonged use When working on the unit do not touch the tube before it has cooled down 5 Safety instructions for assembly ATTENTION Important safety instructions Follow all installation instructions as incorrect installation can lead to serious injuries gt When mounting the motor without any mechanical protection of the driven parts and of the tube which may become hot the motor must be installed at a height of at least 2 5 m above the ground or of another level which provides access to the drive gt Before the motor is installed all cables which are not needed are to be removed and all equipment which is not needed for power operated actuation is to be put out of operation gt The actuating element of a manual release must be mounted at a height of less than 1
10. atures Electronic motor controls features e1 e2 e3 e4 e5 Indirect shade position The blind always moves to the lower end position first turns round there and moves to the shade position Direct shade position E The blind moves directly to the shade position Preset shade position E 0 5 rotations over the lower end position Antifreeze protection E E 2 rotations from the lower end position Torque shut down in UP direction Set up in learning mode a E Only the upper end position has to be learned A GEIGER setting switch is required E E E E External setting switch A switch which allows simultaneous UP and DOWN commands is necessary 6 EN Gerhard Geiger GmbH amp Co KG 100W1503en V001 1214 10 Setting of the end stops Motors GF56 e1 e4 a GEIGER setting switch is required for the setting of the end stops Motors GF56 e5 the setting can be realized with any switch allowing simultaneous UP and DOWN commands Part Nr GEIGER setting switch M56K144 With Hirschmann STAK3 connector D M56F150 With Hirschmann STAK3 connector CH M56F151 With terminal D M56B265 Adaptation cable with terminal and STAS3 M56E399 Adaptation cable with STAK3 and open cable ends Readjustment of the end stops The readjustment of the end stops can be carried out at any time in accordance with the instructions given below If there is no running of the blind by
11. eps lighting The adjustment procedure is completed Setting GJ56 e5 The order of the adjustment process must be strictly adhered to and the adjustment must always be completely implemented all steps Connect the setting switch to the GJ56 e and then plug in power supply Press the programming button till the LED flashes 1 flash light break 1 flash light break then release the programming button Setting of the lower end position press the direction keys to exactly run the GJ56 e to the desired lower end position Press the programming button till the LED flashes 2 flash lights break 2 flash lights break then release the programming button Setting of the upper end position press the direction keys to exactly run the GJ56 e to the desired upper end position Press the programming button till the LED keeps lighting The adjustment procedure is completed When using an external setting switch the UP and DOWN keys must be activated simultaneously instead of the programming key Instead of the lighting up of the LED the motor reacts with a short back and forth movement EN Gerhard Geiger GmbH amp Co KG 100W1503en V001 1214 11 Operation If the shade position working position is not used the GJ56 e can be operated with a standard locked Venetian blind switch If the shade position working position is used e1 e4 a series switch which allows simultaneous UP and DOWN co
12. es for the company Gerhard Geiger GmbH amp Co KG Authorised representative for technical data Gerhard Geiger GmbH amp Co KG Address Schleifmihle 6 D 74321 Bietigheim Bissingen ri f jiter Cet CCELA Bietigheim Bissingen 15 02 2013 Hans Michael Dangel General Manager www geiger de EN 11 EN 16 Notes on waste disposal Recycling of packaging materials In the interest of environmental protection please contact your local government s recycling or solid waste management department to learn more about the services it provides Waste disposal of electric and electronic equipment Electrical and electronic equipment must be collected and disposed of separately in accordance with EU regulations EN For technical questions please call our service team at 49 0 7142 938 333 They will be happy to assist you A Gerhard Geiger GmbH amp Co KG GEIG ER Schleifmiihle 6 Antriebstechnik D 74321 Bietigheim Bissingen Telephone 49 0 7142 938 0 Telefax 49 0 7142 938 230 E Mail info geiger de Internet www geiger de 12 EN Gerhard Geiger GmbH amp Co KG 100W1503en V001 1214
13. mmands is necessary The operation is effected as described below Actuate the key UP to run the motor to the upper end position Actuate the keys UP and DOWN at the same time to run the motor to the shade position working position e1 e4 Actuate the key DOWN to run the motor to the lower end position 12 What to do if Problem Solution Motor does not run e Motor not plugged in Please check the plug connection e Check connecting cable for possible damage e Check the mains voltage and allow the cause of the voltage breakdown to be tested by a specialist electrician Instead of in the upwards direction motor runs downwards e The control leads are interchanged Exchange black brown control leads Motor only runs in one direction e Motor in the end position Run motor in the opposite direction Readjust teh end positions if necessary After running several times the motor breaks down and no longer responds The motor became too hot and has switched off Try it again after a cooling time of about 15 min After setting of the lower end position the blind only runs in DOWN direction EN The motor has been installed upside down see assembly note 13 Maintenance The drive is maintenance free www geiger de EN 9 EN 14 Technical data Technical data GJ56 e with electronic end stop standard electronic
14. ns Please keep these instructions for future reference gt Do not allow children to play with stationary controls Keep remote controls away from children gt The installation is to be checked regularly for defective balance signs of wear or damaged cables and springs if relevant gt Do observe the moving sun protection system and keep persons away until it has closed completely gt When operating the manual release with the sun protection system open please be cautious as it can fall down quickly if springs or tapes wear off or are broken gt Do not operate the device if operations such as for example window cleaning are to be carried out in the vicinity Disconnect the automatic controlled device from the mains power supply if opera tions such as for example window cleaning are being carried out in the vicinity During operation observe the danger zone Do not use the installation if people or objects are in the danger zone Urgently shut down damaged installations until repair Unconditionally shut down the unit during maintenance and cleaning operations Pinching and shearing points are to be avoided and must be secured This appliance can be used by children aged 8 and above and persons whose physical sensorial or mental capacities are impaired or who have no experience or know how if they have been supervised or been given instructions on the use of the appliance and if they understand the possible resulting d
15. veraged over 10 seconds There is no reference to any specific test standard TA CCASA Subject to technical modifications 10 EN Gerhard Geiger GmbH amp Co KG 100W1503en V001 1214 15 Declaration of conformity Ss GEIGER EC Declaration of Conformity Antriebstechnik Gerhard Geiger GmbH amp Co KG Antriebstechnik Schleifm hle 6 D 74321 Bietigheim Bissingen Product Venetian blind motor motor for rolling shutter motor for awnings Type designation GJ56 GR45 GU45 The designated product is in conformity with the European Directive 2006 42 EC Directive 2006 42 EC of the European Parliament and of the Council of 17 May 2006 for the approximation of laws regulations and administrative provisions of the Member States concerning machinery 2004 108 EC Directive 2004 108 EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89 336 EEC The conformity of the designated product with the provisions of the directives is proved in particular by full compliance with the following standards DIN EN 60335 1 DIN EN 55014 1 EN301 489 03 DIN EN 60335 2 97 DIN EN 55014 2 EN300 220 3 DIN EN 62233 DIN EN 61000 3 2 DIN EN 61000 3 3 The accredited VDE Testing and Certification Institute EU Identification No 0366 Merianstr 28 D 63069 Offenbach tests and certifi
Download Pdf Manuals
Related Search