Operating instructions
Contents
1. Z ATN ise D N Operating instructions RC EYE OneLINK No 89036RC Version 11 13 1 INTRODUCTION Dear customer Thank you for making the excellent decision to purchase this RC Logger product You now have a high quality product with a name that represents outstanding products This product complies with the applicable National standards and regulations We kindly request the user to follow the operating instructions to preserve this condition and to ensure safe operation These operating instructions relate to this product They contain important notices on commissioning and handling Please take this into consideration when you pass the product on to third parties Please keep these instructions for further reference All company names and product designations contained herein are trademarks of the respective owners All rights reserved We wish you a great deal of enjoyment with your new RC Logger product A Please download the latest version of the operating instructions from our website at www rclogger com Navigate to the product page and open the Downloads tab Click on Operating instructions to start the download 2 INTENDED USE This product is intended for working with the RC EYE ONE S not included or RC EYE ONE Xtreme not included to allow controlling via branded remote control transmitters With suitable cables the OneLINK is compatible with remote control transmitters from th2. OO ON ONT FP Ww PO 7 INSTALLING THE ANTENNA YJ Connect the included 2 4 GHz antenna to the antenna connector 8 at the top of the RC EYE OneLINk Connect the antenna to the OneLINK before applying voltage to the OneLINK If the OneLINK is powered on without the antenna installed for more than 5 mins it may be damaged 8 INSERTING BATTERIES Open the battery compartment at the rear by sliding the compartment cover towards the bottom Insert two AAA type batteries into the compartment Observe the polarities as indicated in the battery compartment After inserting the batteries the status LED 7 lights up 9 CONNECTING TO A REMOTE TRANSMITTER YJ Connect the microUSB port 6 on the OneLINK to the trainer port of your transmitter by a suitable cable Refer to the cable compatibility table of section 22 Compatibility table and select the correct cable for your transmitter If no transmitter is learned the OneLINK waits for correct learning after first startup When using the OneLINK turn off signal transmission via antenna on your transmitter Signal should only be transmitted via trainer port Read the operating instructions of your transmitter for more information LED indications Solid No signal received from transmitter Flashing slowly OneLINk is transmitting on the chosen channel Troubleshooting Transmitter Is the transmitter turne
3. 7th channel for Camera triggers turn on a 2 CH switch or button and then off A short buzzer beep indicates each channel is learnt Also status LED 5 blinks n th times when the n th channel is learnt example For channel 6 the status LED will blink 6 times After the last channel is learnt the status LED 7 blinks slowly 3 Learning of 7th channel is not a must After an 8 second delay from learning of 6th channel learning mode will automatically be quit if no input for 7th channel is made 12 FREQUENCY SELECTION The OneLINkK is equipped with double frequency Depending on your needs you can switch the frequencies Press and hold the button Select Frequency for approx 3 seconds to enter frequency selection mode Select desired frequency by following below table Frequency selection 915 MHz RC EYE ONE Press button Select Frequency repeatedly until status LED blinks 1 time and 3 buzzer sounds are emitted 89036RC 2 4 GHz RC EYE ONE S RC EYE Xtreme Press button Select Frequency repeatedly until status LED blinks 2 times and 1 buzzer sound is emitted Confirm selection by pressing the ON OFF button After that the OneLINK emits one beep sound 13 CHANNEL SELECTION MODE 3 This section is only valid for RC EYE ONE 1 Hold and press the button Select Frequency 3 for approx 3 seconds to switch to frequency selection mode Once frequency selection mode
4. Mercury Pb Lead You can return used batteries rechargeable batteries free of charge to any collecting point of your local authority our stores or where batteries rechargeable batteries are sold Consequently you comply with your legal obligations and contribute to environmental protection 19 FCC COMPLIANCE STATEMENT FCC ID Y2H 89036RC Statement according to FCC part 15 19 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions gt This device may not cause harmful interference and gt This device must accept any interference received including interference that may cause undesired operation Statement according to FCC part 15 21 Modifications not expressly approved by this company could void the user s authority to operate the equipment 20 PRODUCT SUPPORT Visit http www rclogger com index php contact us or call 852 2559 2662 for product support Additionally visit our support forum at http rclogger com forum 21 TECHNICAL DATA Operating Voltage 2 x 1 5 V DC AAA batteries Transmission FrEQUENCY ceeeeeeeeeeeee 915 MHz 2 4GHz Dimensions W x H X D nasses 59 x 65 x 21 5 mm cle P A E E E T 70g 22 COMPATIBILITY TABLE JH an Th Supporting Brand Futaba 4 7 N Af pe L o VNS Supporting Model 4YF 72 MHz 4YBF 6EX 6J 7C 8FG 8J 9C 10C 12FG amp 145G 4YF 2 4 GHz 1
5. is enabled the OneLINK emits a beep sound and the status LED 7 goes out 2 Press the button Learning to navigate through channels 1 5 Each channels is indicated by the corresponding number of beep sounds example Channel 5 five beep sounds 3 To cancel close the channel selection mode press the button ON OFF The OneLINK emits one beep sound and enters operation mode again The status LED blinks slowly 14 BINDING To bind the OneLINk to your model craft proceed as follows 1 Press button Bind 2 once The OneLINK enters binding mode for 20 seconds 2 The OneLINK is being bound to the RC EYE ONE S Xtreme The status LED 7 blinks fast during binding and blinks slowly again once binding has completed 3 Check the status LED on your RC EYE ONE S RC EYE Xtreme to confirm successful binding 4 gt a SiN ts l Di T aial ogger 15 LOW BATTERY ALERT A repeated beep sound at 5 seconds interval indicates depleted batteries You must stop operation immediately and replace the batteries before operating again 16 FIRMWARE UPGRADE You may upgrade the firmware via a computer Proceed as follows to upgrade the firmware 1 Use the provided Micro USB to USB cable and connect the OneLINK to a computer via the microUSB port 6 2 Remove the batteries from the battery compartment 3 While pressing and holding the Upgrade Firmware b
6. 2Z 14MZ amp 18MZ Tower Hobbies Futaba 4TH amp 6XM 4VF 5U 6A 6DA 6H 6YF 6YG 7NFK 8U amp 9Z Hitec Neon Flash 4sx 5 5SX Focus 4 6 Laser 4 6 Optic 5 72 MHz Optic 6 72 MHz 2 4 GHz Eclipse 7 72 MHz Prism 7 amp Prism 7X Tower Hobbies JR 4FM amp 6FM All aircraft transmitters with trainer DSC jack Spektrum DX4e DX5e DX6 DX6i amp DX7 DX7s DX8 DX10t amp DX18 Graupner MX 16 Hitec Hitec Optic 5 Optic 6 Sport amp Eclipse 7 2 4 GHz Aurora 9 E C Logger These operating instructions are published by CEI Conrad Electronic International HK Limited 18th Floor Tower 2 Nina Tower No 8 Yeung Uk Road Tsuen Wan New Territories Hong Kong All rights including translation reserved Reproduction by any method e g photocopy microfilming or the capture in electronic data processing systems require the prior written approval by the editor Reprinting also in part is prohibited The operating instructions reflect the current technical specifications at time of print We reserve the right to change the technical or physical specifications 2013 by CEI Conrad Electronic International HK Limited V2_1113 JH 1
7. d on Faulty cable connection Disconnect and re connect the cable Cable JH TTN hiat 10 POWER ON OFF To turn the OneLINK on press the button ON OFF 1 once To turn the OneLINK off press and hold the ON OFF button for approx 3 seconds The status LED 7 goes out Note the following conditions when using the OneLINK gt If the OneLINk is turned off when cable is not connected a short press to the button ON OFF 1 turns the OneLINK on until signal received from the transmitter connected and turned on gt Auto power off The OneLINK turns off automatically if no user input is detected for 7 minutes You can wake the OneLINk by pressing the ON OFF button 11 LEARNING Ensure no mixer is applied on your transmitter and put throttle to zero position Hold and press the button Learning 3 for approx 3 seconds to enable learning mode for the remote control The OneLINK emits a buzzing sound indicating the mode is enabled As a next step you must learn the channels with the transmitter 1st channel push throttle to max and back to 0 2nd channel push rudder to left and back to 0 3rd channel push nick to front and back to 0 4th channel push roll to left and back to 0 oth channel for flight mode turn on a 3 CH switch and then off 6th channel for height hold normal acromode function turn on a 3 CH switch and then off
8. e most popular brands in the model craft industry Read the instructions carefully and keep them Make this product available to third parties only together with its operating instructions 3 From here onwards the RC EYE OneLINK is referred to as OneLINK DELIVERY CONTENT RC EYE OneLINK 2 4 GHz Antenna Futaba box trainer cable 89056RC JR mono plug trainer cable 89058RC Micro USB to USB Cable 89060RC 2 x 1 5 V AAA battery Operating instructions VV Vi VM VM VM M O 4 PRODUCT COMPATIBILITY The TX module can be used in combination with the following other RC Logger products gt Micro USB Trigger Port Cable 89059RC gt Futaba Round Trainer Cable 89057RC 5 SAFETY INSTRUCTIONS YJ Persons Product gt The device is not a toy Keep it out of the reach of children and pets gt Do not leave packaging material lying around carelessly These may become dangerous playing material for children gt Protect the product from extreme temperatures direct sunlight strong jolts high humidity moisture flammable gases vapours and solvents gt Do not place the product under any mechanical stress Read the operating instructions carefully and especially observe the safety information If you do not follow the safety instructions and information on proper handling in this manual we assume no liability for any resulting personal injury or damage to property Such cases will invalidate the warranty guarant
9. ee We SS ome aa E C Logger gt If itis no longer possible to operate the product safely take it out of operation and protect it from any accidental use Safe operation can no longer be guaranteed if the product is visibly damaged is no longer working properly has been stored for extended periods in poor ambient conditions or has been subjected to any serious transport related stresses gt Please handle the product carefully Jolts impacts or a fall even from a low height can damage the product gt Also observe the safety and operating instructions of any other devices which are connected to the product gt Not following the instructions in these operating instructions may result in dangers such as short circuit fire electric shock etc Observe the safety information under all circumstances Miscellaneous gt Consult an expert when in doubt about operation safety or connection of the device gt Maintenance modifications and repairs are to be performed exclusively by an expert or at a qualified shop gt If you have questions which remain unanswered by these operating instructions contact our technical support service or other technical personnel 6 OPERATING ELEMENTS Button ON OFF Button Bind Select Frequency Button Learning Upgrade Firmware Battery compartment Receiver body microUSB port Status LED Antenna connector Antenna
10. utton insert the batteries into the battery compartment The OneLINK shows up as a USB mass storage device in your computer It may take up to 3 minutes 4 Inthe shown USB mass storage drive replace the file firmware bin with the latest firmware file 3 Further information can be found on http Wwww rclogger com 17 MAINTENANCE CARE AND REPAIR gt Remove the batteries before cleaning and maintenance gt Regularily clean the OneLINK with a dry cloth gt Do not use abrasive cleaners or alcohol gt Repairs should only be handled by a professional 18 DISPOSAL General a Batteries rechargeable batteries The user is legally obliged battery regulation to return used batteries and In order to preserve protect and improve the quality of environment protect human health and utilise natural resources prudently and rationally the user should return unserviceable product to relevant facilities in accordance with statutory regulations The crossed out wheeled bin indicates the product needs to be disposed separately and not as municipal waste rechargeable batteries Disposing used batteries in the household waste is prohibited Batteries rechargeable batteries containing hazardous substances are marked with the crossed out wheeled bin The symbol indicates that the product is forbidden to be disposed via the domestic refuse The chemical symbols for the respective hazardous substances are Cd Cadmium Hg
Download Pdf Manuals
Related Search