Mini-K Thermocouple Thermometer Operating Instructions
Contents
1. HOLD a second time the word HOLD appears in the LCD The last measured value is frozen and the thermometer deactivates itself automatically after about 15 seconds to save battery power Plug ina probe CAUTION The thermometer should be protected from the following 1 Electro Static Discharge 2 Thermal shock caused by large or abrupt ambient temperature changes allow 30 minutes for unit to stabilize before use when exposed to thermal shock 3 Do not leave the unit on or near objects of high temperature 4 Keep out of reach of all children STORAGE amp CLEANING Clean the device with a damp cloth Do not use any solvents such as Aceton as they corrode the plastic Isopropyl alcohol may be used to disinfect Do not submerge any part of the thermometer The thermometer should be stored at room temperature between 20 to 65 C 4 149 F LCD ERROR MESSAGES The thermometer incorporates visual diagnostic messages as follows T a oi Cre me 5 ak ad cr Er2 is displayed when the thermometer is exposed to rapid changes in the ambient temperature Er3 is displayed when the ambient temperature exceeds 0 C 32 F or 50 C 122 F The thermometer should be allowed plenty of time minimum 30 minutes to stabilize to the working room temperature Error 5 9 for all other error messages it is necessary to reset the thermometer To reset it turn the instrument off remove the battery and w2. Mini K Thermocouple Thermometer Operating Instructions Congratulations on the purchase of the product We hope than you can make use of this product for a long time and that it helps you with your work Information that are useful and important for understanding the function are highlighted in the instructions text Powered by a replaceable lithium battery the thermometer is a handy temperature measurement device for a whole range of measurement and control applications 1 LCD 2 ON HOLD oe OF Fs 4 Thermocouple Socket 5 Battery Cover 1 LGD 2 ON HOLD OPERATION 3 C 1 Power on To switch the thermometer on keep KeyON HOLD 2 pressed 4 Thermocouple for approximately one 5 Battery cover socket second 2 Display LCD All necessary information is displayed on an LCD The individual symbols have the following meanings 2 1 Display for current measured values 2 2 Minus sign negative measured values 2 3 Battery status indicator 2 4 HOLD Auto shut down after 15 sec 2 5 Temperature unit 3 Measuring temperature Select the required unit of measurement C or F C F can be changed only when Hold is shown f HOLD C 4 Position the tip of the thermocouple where you wish to measure the temperature and press ON HOLD key Wait till the temperature has stabilized and subsequently read the value from the display Now the current temperature is displayed for about 4 min If you press ON
3. ait for a minimum of one minute reinsert the battery and turn on If the error message remains please contact the Service Department for further assistance Hi or Lo is displayed when the temperature being measured is outside of the i H I rL O measurement range BATTERIES The thermometer incorporates visual low battery indication as follows D cw FK Battery OK measurements Battery Low battery needs to be are possible replaced measurements are still possible BATTERY REPLACEMENT When the Low Battery icon indicates the battery is low the battery should be replaced immediately with a CR2032 lithium cell The battery is located under the twist cover at the rear of the thermometer Please note It is important to turn the instrument off before replacing the battery otherwise the thermometer may malfunction Dispose of used battery properly and keep away from children SPECIFICATION Probe Measurement Range Battery Exhausted measurements are not possible 64 to 1400 C 83 2 to 1999 F K type Socket 0 50 C 32 122 F 1 of reading or 1 C 1 8 F whichever is greater 0 1 C 0 1 F TCP 100 hours continuous use Dimensions 78 x 43 x 20 mm 3x1 7x0 8 inch Weight 40 15 grams 1 42 oz including a CR2032 lithium cell The thermometer will automatically shut off if left idle for more than 15 sec Caution The measure range is for thermometer only User should choose proper p
4. robe types for different kinds of application Please make sure the target to be measured will not exceed the temperature range of the probe to avoid permanent damage of the thermocouple probe A Caution To avoid electric shock and thermometer damage do not measure live circuit where voltage exceeding 24V AC RMS or 60V DC with the thermocouple probe A EMC RFI Readings may be affected if the unit is operated within radio frequency electromagnetic field strength of approximately 3 volts per meter but the performance of the instrument will not be permanently affected A ce amp Operating Range Accuracy Tamb 25 C Resolution 9 9 199 9 C Battery Life Ref No 082007
Download Pdf Manuals
Related Search