Operating Instructions - Exor International SpA
Contents
1. Fig 5 1 1 Power 2 Aux Port 3 PLC Port 4 PC Printer Port 5 Ethernet Port 6 USB Port Fig 4 2 Fig 5 2 MANUGENETOP3xx UniOP Operating Instructions VER 1 03 17 EXOR CONNECTIONS 5 1 Serial Port The serial port is used to communicate with the PLC or with another type of controller Different electrical standards are available for the signals in the PLC port connector RS 232 RS 422 RS 485 The serial port is software programmable Make sure you select the appropriate interface in the programming software RS 422 RS 485 Pin Description EA SERIAL PORT 1 TEL 9 The communication cable must be chosen for the type of device being connected MANUGENETOP3xx UniOP Operating Instructions VER 1 03 18 EXOR 5 2 Ethernet Port Pin_ Description 4 4 5 6 RXOUT y MANUGENETOP3xx UniOP Operating Instructions VER 1 03 CONNECTIONS ON Valid link has NOT been detected OFF Valid link has been detected 19 A POWER SUPPLY GROUNDING AND SHIELDING 6 Power Supply Grounding and Shielding The power supply terminal block is shown in the figure below 24V L Common M 0 Oy C I 2 DO 3 Power supply terminal b2. D A Operating Instructions Description of the UniOP eTOP Series 300 Exor International S p A MANUGENETOP3xx UniOP Ver 1 03 Copyright O 2011 2013 Exor International S p A Verona Italy Subject to change without notice The information contained in this document is provided for informational purposes only While efforts were made to verify the accuracy of the information contained in this documentation it is provided as is without warranty of any kind Third party brands and names are the property of their respective owners www uniop com MANUGENETOP3xx UniOP Operating Instructions VER 1 03 EXOR TABLE OF CONTENTS Table of Contents Introduction RN 4 5 1 Product oVervieWi ss sen in re Ida tenants dent dedans ane sdeiiedasadadeneagaeeduiasnadneatecen 6 2 Standards 7 3 Technical Specifications eee 8 A Technical data dada in iii 10 4 1 DIMENSIONS crios etes e dent ad aE de dents 14 4 2 Installation environment O 15 4 3 Installation procedure 000 16 5 000 17 1 Serial POM iatera nan te tete least tab are 18 7 19 6 Power supply grounding and shielding nan n cc nc canon nn cnc cnnnnncncnnnnns 21 TAUX 22 8 aiii Iii aA a 23 9 Cleaning faceplates acomodada AEAN ANAR 24 40 Get MG Stead aie sacs apna E A it 24 11 Command SUMMARY a AAA 25 12 Configuration ads 26 13 Special Modes Calibrati
3. 4 GHz 2 GHz 3 V m 2 GHz 2 7 GHz 1 V m EXOR Burst immunity test Surge immunity test Immunity to conducted disturbances inducted by radiofrequency field Voltage dips short interruptions and voltage variations immunity test STANDARDS AND APPROVALS 2 KV DC power port EN 61000 4 4 1 KV signal line 0 5 KV DC power port line to earth EN 61000 4 5 0 5 KV DC power port line to line 1 KV signal line line to earth 0 15 80 MHz 10V EN 61000 4 6 Port AC mains Level 100 duration 1 cycle and 250 cycles 50Hz 40 duration 10 cycles 50Hz 70 duration 25 cycles 50Hz Phase 0 180 Test executed on the 230Vac side of the Exor International Power Supply EN 61000 4 11 Durability information Backlight service life LED type Backlight service life CCFL type Front foil without directly exposure to sunlight or UV ray UV Resistance Touch screen reliability 40000 Hrs or more Time of continuos operation until the brightness of the backlight reaches 50 of the rated value when the sorrounding air temperature is 25 C see Note 1 50000 Hrs or more Time of continuos operation until the brightness of the backlight reaches 50 of the rated value when the sorrounding air temperature is 25 C see Note 1 10 years if the surrounding air temperature is 25 C Indoor applications After 300 hours cycled humidity in QUV accelerated weathering some yellowing and brittlene
4. about half a second 4 The panel will remain with black screen and system leds blinking MANUGENETOP3xx UniOP Operating Instructions VER 1 03 26 EXOR A AAA DEDICATED LED INDICATORS 14 Dedicated LED Indicators The table below shows the name and the symbol when available of the LED indicators dedicated to special functions Please note that some indicators may be available only in some models of UniOP operator panels LED Indicator Name symbol lt gt No hardware problem detected BLINK Battery low Hardware fault BLINK Communication error not all models While any key is pressed visual feedback FF ON FF RUN O green Hardware fault Unit in operation ON FF ON ON A BLINK Alarm requires acknowledgment gt green O No keys are pressed and no errors O O Communication OK nemase o Recipe data backup in progress You will find a complete reference to programming this product in the UniOP User s Manual MANUGENETOP3xx UniOP Operating Instructions VER 1 03 27 UNPACKING AND PACKING INSTRUCTIONS EXOR Unpacking and Packing Instructions Qe 2 3 15 To repack the unit please follow the instructions backwards MANUGENETOP3xx UniOP Operating Instructions VER 1 03 28
5. calibration procedure should be used in all cases when it would result not possible to go to calibration using the standard procedure 1 Switch off the unit 2 turn on the unit 3 tap in the middle of the touchscreen with a frequency of about half a second until the operator panel will enter the Calibration Mode 4 perform the standard calibration procedure 122 Go to Configuration Mode In the case it might prove impossible to switch the operator panel to Configuration Mode due to problems in the start up phase follow the procedure below 1 Switch off the unit 2 Touch in the middle of the left side of the display screen with the left hand 3 Switch on the operator panel and tap with the right hand in the middle of the right side of the display screen with a period of about half a second 4 Continue until the screen will show Configuration Mode 12 3 Safe Mode UniOP safe mode allows some specific and special operations to be performed on the unit Under some circumstances safe mode is required to reset the panel contrast adjustment parameters The UniOP safe mode activation is similar to the emergency procedure that activates Configuration Mode at start up 1 Switch off the unit 2 Divide the screen in two parts with a horizontal imaginary line press and hold one finger on the upper part of the display screen 3 Switch on the operator panel and tap in the bottom part of the display screen with a period of
6. film The equipment is not intended for installation in contact with corrosive chemical compounds Check the resistance of the front panel film to a specific compound before installation Do not use tools of any kind screwdrivers etc to operate the keyboard ofthe panel or the touch screen In order to meet the front panel protection classifications proper installation procedure must be followed e the borders of the cutout must be flat e screw up each fixing screw until the plastic bezel corner get in contact with the panel e the cutout for the panel must be of the dimensions indicated in this manual The IP65 is guaranteed only if e max deviation from the plane surface to the cut out 0 5mm e thickness of the case where is mounted the equipment from 1 5mm to 6mm e max surface roughness where the gasket is applied 120 um Applying the rectangular gasket The gasket should be applied on the rear of the frame Fig 4 1 A Gasket B Installation cut out MANUGENETOP3xx UniOP Operating Instructions VER 1 03 15 X OR TECHNICAL DATA 4 3 Installation Procedure Place the fixing brackets as shown in figure Fig 4 2 Fig 4 2 yr CAUTION Screw each fixing screw until the bezel corner gets in contact with the panel MANUGENETOP3xx UniOP Operating Instructions VER 1 03 X A CONNECTIONS 5 Connections
7. via USB connection e Multilanguage applications Far East languages are supported The number of runtime languages is limited only by the available memory All text information in the application can be exported to files in Unicode format for easier translation e Powerful macro editor to configure touchscreen operation e Alarms and historical alarm list Alarm and event information can be printed or transferred to an host computer e Eight level password protection e Report printing to serial printer Reports are freely configurable using Designer gt Ethernet based UniNet network to share data between UniOP HMIs and to serve data using UniNet OPC Server MANUGENETOP3xx UniOP Operating Instructions VER 1 03 EXOR ss STANDARDS AND APPROVALS 2 Standards and Approvals The products have been designed for use in an industrial environment in compliance with the 2004 108 EC EMC Directive The products have been designed in compliance with EN 61000 6 4 EN 55011 Class A EN 61000 6 2 EN 61000 4 2 EN 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 6 The installation of these devices into the residential commercial and light industrial environments is allo wed only in the case that special in measures are taken in order to ensure conformity to EN 61000 6 3 The products are in compliance with the Restrictions on Certain Hazardous Substances RoHS Directive 2002 95 EC In compliance with the above regulations the products a
8. E The pin assignment of the Aux Port connector is described in the manual of the communication module ATTENTION Insert the module pressing simultaneously on the four corners Do not plug the module and the ETAD adapter when power is applied to the operator panel MANUGENETOP3xx UniOP Operating Instructions VER 1 03 21 EXOR mb BATTERY 8 Battery These devices are equipped with rechargeable Lithium battery not user replaceable The following information is maintained by the battery hardware real time clock date and time event list Charge At first installation must be charged for 48 hours When the battery is fully charged it ensures a period of 3 months of data back up at 25 C Battery IT IT ATTENTION Dispose of batteries according to local regulations MANUGENETOP3xx UniOP Operating Instructions VER 1 03 22 EXOR CLEANING FACEPLATES HANDLING THE MEMORY CARD 9 Cleaning Faceplates The equipment must be cleaned only with a soft cloth and neutral soap product Do not use solvents 10 Getting Started UniOP panels must be programmed with the programming package Designer To program a panel you will have to connect the panel to a personal computer running Designer software package the panel must be in Configura
9. S 485 RS 422 UniNet server and client yes es Aux port optional fieldbus Ethernet y Ethernet port 10 100 Mbit Usb port Host interface version 1 1 O 8 pas PES MANUGENETOP3xx UniOP Operating Instructions VER 1 03 TECHNICAL DATA 13 EXOR TECHNICAL DATA 4 1 Dimensions A lt gt A JE m E y y F E gt lt gt 6 gt gt gt A a Y EE EEES eTOP306 187mm 7 36 147mm 5 79 176mm 6 90 136mm 5 35 45mm 1 77 4mm 0 16 eTOP307 187mm 7 36 147mm 5 79 176mm 6 90 136mm 5 35 45mm 1 77 4mm 0 16 eTOP308 232mm 9 13 187mm 7 36 221mm 8 70 176mm 6 90 42mm 1 65 4mm 0 16 eTOP310 287mm 11 30 232mm 9 13 276mm 10 86 221mm 8 70 42mm 1 65 4mm 0 16 eTOP312 337mm 13 26 267mm 10 51 326mm 9 30 256mm 10 1 42mm 1 65 4mm 0 16 eTOP313 337mm 13 26 267mm 10 51 326mm 9 30 256mm 10 1 42mm 1 65 4mm 0 16 eTOP315 392mm 15 43 307mm 12 1 381mm 15 296mm 11 65 46mm 1 82 4mm 0 16 MANUGENETOP3xx UniOP Operating Instructions VER 1 03 14 EXOR A TECHNICAL DATA 4 2 Installation Environment The equipment is not intended for continuous exposure to direct sunlight This might accelerate the aging process of the front panel
10. acro Editor facility of the programming software The chapter describes the touchscreen commands recognized by all UniOP panels Commands are classified according to the operating modes of the unit UniOP panels with touchscreen interface will show a touch keypad on the screen whenever operator input in required For System Commands the default keypad in shown in figure All keypads except the one shown in Configuration Mode can be changed by the programmer Touch screen panels will show automatically a numeric keypad whenever the data entry phase is acti vated Pop up keypads are configurable by users NOTE The text 2 s associated to a key means that the key must be held pressed for two seconds to acti vate the associated function MANUGENETOP3xx UniOP Operating Instructions VER 1 03 24 EXOR sh CONFIGURATION MODE 12 Configuration Mode ENTER shows the type and version of the communication driver stored in the unit if any and boot FW version ENTER 2s returns to Operation Mode if a valid communication driver and a valid project are stored in the unit the key must be pressed for 2 seconds CLEAR 2s Call standard touchscreen calibration procedure M2s Update firmware 2s Erase Static RAM Password and Recipe reset 32s Shows memory menu To change the panel IP address Ethernet GMT and DST settings touch the item you want to change 11 1 Operation Mode Page Mode To recall the Configuration Mode touc
11. back up battery Designer version 6 0 50 C EN 60068 2 14 20 70 C 5 85 RH not condensing 5 9Hz 7 mm 9 150 1g 50 0 11 ms 3 pulses per axis IP66 front panel EN 60068 2 14 EN 60068 2 30 5 EN 60068 2 6 EN 60068 2 27 EN 60529 The front face of the UniOP unit installed in a solid panel has been tested using conditions equivalent to the standards shown in the Environmental conditions Even though the level of resistance UniOP unit is equivalent to these standards oils that should have no effect on the UniOP can possibly harm the unit This can occur in areas where either vaporized oils are present or where low viscosity cutting oil are allowed to adhere to the unit for long periods of time If the front face protection sheet on the UniOP becomes peeled off these conditions can lead to the ingress of oil into the UniOP and separate protection measures are suggested If the installation gasket is used for a long period of time or if the unit and its gasket are removed from the panel the original level of the protection cannot be guaranteed Electromagnetic Compatibility EMC Radiated disturbance test Electrostatic discharge immunity test Radiated radio frequency electromagnetic field immunity test MANUGENETOP3xx UniOP Operating Instructions VER 1 03 Class A EN 55011 8 kV air electrostatic discharge EN 61000 4 2 4 kV contact electrostatic discharge 80 MHz 1 GHz 10V m EN 61000 4 3 1
12. h the screen in an area where no active touch areas have been defined and hold for 2 seconds The value of 2 seconds can be changed with Designer on disabled requiring the use of a touch button programmed with the specific enter configuration mode macro Command Menu A select up y select down select left gt select right ENTER activate selection CLEAR return to Page Mode System Menu A select up y select down activate selection gt activate selection ENTER return to Page Mode when EXT is selected CLEAR return to Page Mode MANUGENETOP3xx UniOP Operating Instructions VER 1 03 25 EXOR SPECIAL MODES CALIBRATION CONFIGURATION AND SAFE MODE 13 Special Modes Calibration Configuration and Safe Mode 12 1 Touchs Screen Calibration Go to Calibration Mode Touchscreen calibration may be required to restore proper operation of the touchscreen interface 12 1 1 Standard Calibration 1 Recall Configuration Mode 2 Touch and hold CLEAR key on the screen until TOUCH SCREEN CALIBRATION message appears then follow the instructions on page reported also below touch and hold the x symbol in the right upper corner until it will move to the low left corner of the screen touch and hold the x symbol in the low left corner touch the key touch the key until the indication to touch the Enter key will be displayed on the screen touch the Enter key ww Nod 12 1 2 Emergency Calibration The Emergency
13. lock Fig 6 1 Note Ensure that the power supply has enough power capacity for the operation of the equipment The unit must always be grounded to earth Grounding helps limit the effects of noise due to electro magnetic interference on the control system Earth connection will have to be done using either the screw or the faston terminal located near the power supply terminal block A label helps identify the ground connection Also connect to ground the terminal 3 on the power supply terminal block The power supply circuit may be floating or grounded In the latter case connect to ground the power source common as shown in figure see below with a dashed line When using the floating power scheme note that the panes internally connects the power common to ground with a 1MQ resistor in parallel with a 4 7nF capacitor The power supply must have double or reinforced insulation The suggested wiring for the power supply is shown below Fig 6 2 All the electronic devices in the control system must be properly grounded Grounding must be performed according to applicable regulations MANUGENETOP3xx UniOP Operating Instructions VER 1 03 20 AUX PORT 7 AUX Port The AUX Port is a communication port specially designed for industrial network communication The AUX Port connector is a 9 pin D sub type The functionality of the AUX Port depends on the optional communication module which is plugged into the unit NOT
14. olor CCFL TFT Color CCFL Colors gt User memory flash 64MB 64MB Recipe memory Yes Flash memory storage Yes Flash memory storage limited only by available limited only by available memory memory PLC Port RS 232 RS 485 RS 232 RS 485 RS 422 RS 422 Programming Printer Port RS 232 RS 485 RS 232 RS 485 RS 422 RS 422 Ethernet programming Ethernet port SS Mbit as Mbit REA A 8880388888 8 4 EE EA e 6 Temperature range vertical installation 0 50 C 0 50 C i MANUGENETOP3xx UniOP Operating Instructions VER 1 03 11 TECHNICAL DATA eTOP312 eTOP313 Display Backlight TFT Color CCFL TFT Color LED EXI AENA O AI Recipe memory Yes Flash memory storage Yes Flash memory storage limited only by available limited only by available memory memory PLC Port RS 232 RS 485 RS 232 RS 485 RS 422 RS 422 Programming Printer Port RS 232 RS 485 RS 232 RS 485 RS 422 RS 422 es 6 E S Current rating at 24VDC 1 05A Temperature range vertical installation 0 50 C 0 50 C EA MANUGENETOP3xx UniOP Operating Instructions VER 1 03 12 Model eTOP315 Display Backlight TFT Color CCFL 0 Diagonal inches User memory flash Flash card option o lt D 0 lt o al 0 s Recipe memory Yes Flash memory storage limited only by available memory PLC Port RS 232 RS 485 RS 422 Programming Printer Port RS 232 R
15. on Configuration and Safe Mode 27 14 Dedicated led indicators ses 8 15 Unpacking and packing instructions 29 MANUGENETOP3xx UniOP Operating Instructions VER 1 03 EXOR INTRODUCTION Introduction The operational guidelines described below is information which relates to the device installation tran sportation storage assembly use and maintenance This Operating Instruction describes the main features of the UniOP operator panels The Guide refers to the following models eTOP306 Operator interface with TFT color 5 7 display eTOP307 Operator interface with TFT color 7 widescreen display eTOP308 Operator interface with TFT color 7 5 display eTOP310 Operator interface with TFT color 10 display eTOP312 Operator interface with TFT color 12 display eTOP313 Operator interface with TFT color 13 3 widescreen display eTOP315 Operator interface with TFT color 15 display MANUGENETOP3xx UniOP Operating Instructions VER 1 03 X OR ELA SAFETY M Safety Guide The manual contains safety standards that must be respect for the personal safety and to avoid damage Indications of attention are divided into three levels of danger DANGER indicates a failure to observe safety rules and such failure may cause death or serious bodily harm DANGER ATTENTION indicates a failure to observe safety rules and that deficiency may cause damage ATTENTION CAUTION indicates a failure to observe safet
16. re CE marked Product Identification The product may be identified through a plate attached to the rear cover You will have to know the type of unit you are using for correct usage of the information contained in the guide An example of this plate is shown in the figure below UniOP 66 eTOP306 08 09 Power Supply 24V 0 55A j pean UA SW v 5 90C 6 eTOP306 product model name 08 09 month year of production 09994847559 serial number H W V hardware version of the product S W V software version of the product MANUGENETOP3xx UniOP Operating Instructions VER 1 03 X OR 3 Technical Specifications Touch screen technology Back up battery Fuse PC Printer Port PLC Port AUX Port User memory Recipe memory Hardware clock Accuracy RTC at 25 C operating Alarms Historical event list Programming software Environmental conditions Operating temperature vertical installation Storage temperature Operating and storage humidity Vibrations Shock Protection class STANDARDS AND APPROVALS Resistive 3V 50mAh Lithium rechargeable not user replaceable model VL2330 Automatic RS 232 RS 485 RS 422 software configurable 300 38400 baud RS 232 RS 485 RS 422 software configurable 300 38400 baud connector D 9 pin female functionality can be configured with an optional communication module 64MB Flash Clock Calendar with back up battery lt 100ppm 1024 last 1024 events with
17. ss may be present see Note 2 gt 1 milion operations Note 1 Extended use in environments where the surrounding air temperature is 40 C or higher may degrade backlight quality reliability durability Note 2 Solvent resistance Contact for 1 2 hour at 21 C No visible effect Acetone Butyl Cellosolve Cyclohexanone Ethyl Acetate Hexane Isopropyl Alcohol MEK Methylene Chloride Toluene Xylene Contact for 24 hours at 49 C No visible effect Coffee Ketchup Lemon Juice Mustard slight yellow stain Tea Tomato juice MANUGENETOP3xx UniOP Operating Instructions VER 1 03 4 Technical Data Display Backlight Colors Resolution Diagonal inches Touch screen User memory flash Flash card option Recipe memory PLC Port Programming Printer Port UniNet server and client Aux port optional fieldbus Ethernet Ethernet programming Ethernet port Usb port Video input Option Trend acquisition and display Battery Real Time Clock Password Event list Voltage Current rating at 24VDC Temperature range vertical installation MANUGENETOP3xx UniOP Operating Instructions VER 1 03 TECHNICAL DATA eTOP306 eTOP307 IA Yes Flash memory storage Yes Flash memory storage limited only by available limited only by available memory memory RS 422 RS 422 RS 422 RS 422 A 1024 18 30VDC 18 30VDC 0 55A 0 55A 0 50 C 0 50 C 10 TECHNICAL DATA Display Backlight TFT C
18. tion mode to be programmed Use the cable CA253 to connect the panel to a personal computer The software package Designer is a Windows application and must be properly installed The Win dows environment is not included in the software package Designer and must already be installed on the personal computer The software package can use either the communication ports COM1 or COM2 on the personal computer Check that the Designer program is correctly configured to comunicate with the communication port to which the cable attached The communication parameters between the panel and the personal computer are speed 9600 models PC Printer Port sup also speeds of 19200 and 38400 baud parity none stop bit 1 The Designer software defaults to the correct parameters The version of the Designer being used must be compatible with the firmware version of the panel to be programmed Call for more information on compatibility between firmware and programming software MANUGENETOP3xx UniOP Operating Instructions VER 1 03 23 EXOR COMMAND SUMMARY 11 Command Summary The UniOP panels have an extended set of pre defined commands Commands are available for the use of the built in system functions including navigation in all system pages CAUTION g The standard command assignment is described in this chapter All the commands except those defined for Configuration Mode can be changed deleted and or extended using the Keyboard M
19. y rules and that deficiency may cause defects to the equipment or inconsistencies CAUTION MANUGENETOP3xx UniOP Operating Instructions VER 1 03 a EXOR PRODUCT OVERVIEW 1 Production Overview The UniOP eTOP Series 300 combines state of the art features and performance with an oustanding design They are the ideal choice for HMI applications including factory and building automation The eTOP Series 300 HMI panels are fully compatible with UniOP Designer 6 software Powerful and intuitive programming with the UniOP Designer 6 software Supports more than 150 communication drivers Built in Ethernet port for communication with devices programming the HMI from Designer and retrieving data from computers e USB host port for the connection of flash drives Flash drives can be used for upgrading applications and firmware e Optional plug in modules for fieldbus systems and networks Compatible with TCM and SCM modules e Dual driver communication capability e Vector graphic capabilities including the support of multiple layers and object transparency e Data display in numerical text bargraph analog gauges and graphic image formats Dynamic object properties supported e Data acquisition and trend presentation Trend data can be transferred to an host computer using the Ethernet connection e Recipe data storage Recipe data can be transferred to an host computer using the Ethernet connection or copied to flash drives
Download Pdf Manuals
Related Search