Operating Instructions (English)
Contents
1. These accessories are used for installation work Note e Keep unattached pen holders and their screws in a safe place together with the Operating Instructions this document Operating Instructions and Installation Manual in other languages may be included depending on the country area e The warranty may not be included depending on country area Stand and electronic pen are optional devices page 33 e Replacement penpoints for the electronic pen are optional devices page 33 About Using the DVD ROM To prevent damage to the DVD ROM Do not touch or write on the surface of the disc Do not leave the disc out of the protective case Do not leave the disc in the direct sunlight or near heat sources Do not place heavy objects on the disc case or drop the case To clean the disc hold the disc by its edges and wipe it from the center to the edges with a dry soft cloth Usage Names and Uses of the Parts Main unit Front View Status LED Lights green when the power is on Lights red when an error occurs Undetectable Area Ya The position of your finger or the electronic pen in this p area cannot be detected Make sure that the projected p image does not overlap with this area Screen Board Detects the position of your finger or the electronic pen Project the contents of a computer screen using a projector Electronic Pen Signal Receiver This receives the signals from the electron2. E te 1m 3 ft 3 in Notice e Do not place any obstructions between the electronic pen and elite Panaboard e Do not expose the elite Panaboard s electronic pen signal receiver to direct sunlight or to the intense light from an inverter fluorescent light e Use a dry cloth to wipe off the dust on the elite Panaboard s electronic pen signal receiver Usage Connecting External Components 1 Connect the elite Panaboard to a computer using the USB cable e Plug the USB cable into a USB port on the computer Notice e Do not connect the elite Panaboard to a computer via USB unless elite Panaboard driver software book is installed Only connect the USB cable after following the steps in Installing the Software page 19 to install the software To USB Port o Projector AC Video Cable In the case of the UB T580 the length of the USB cable from the edge of the main unit is approx 2 7 m 8 ft 10 5 16 in when it is connected to the left side and approx 2 4 m 7 ft 10 1 2 in when it is connected to the right side In the case of the UB T580W the length is reduced by about 15 cm 5 7 s in each on both sides 2 Connect the computer to a projector e For instructions on connecting your computer and projector refer to the respecting instruction manuals About the Usage Location e Do not place the elite Panaboard where it is directly exposed to sunlight e Do not use the eli
3. 20 Usage 8 When the following screen is displayed confirm that the USB cable is not connected to your computer or the elite Panaboard and click OK e If the USB cable is connected to the computer disconnect the cable and click OK e If Microsoft NET Framework 3 0 SP 2 or later or 3 5 SP 1 or later is not installed an installation screen will be displayed Follow the on screen directions to install these components Software Installation Software installation will begin Please confirm that the USB cable is disconnected from the electronic board or the comupter Installation may take a few minutes to complete During installation Cancel is unavailable Cancel O When the installation wizard is displayed follow the on screen instructions and continue with the installation 10 When installation has finished click Finish Restart your computer if you are prompted to do so The elite Panaboard group and the Panasonic Software Update Manager group will be created in the Panasonic group in the program menu The following items are installed in the elite Panaboard group A function that you deselected on the Select Features screen in step 7 will not be displayed elite Panaboard software elite Panaboard book Operating Instructions Software Help Download the latest version HD Visual Communication Unit Screen Selection Tool Th
4. 22 finger or the electronic Perform Advanced Calibration pen e Another finger was detected during the calibration process Raise your finger vertically when touching the screen board 22 to avoid other fingers being detected when the calibration process is initiated e The Electronic Pen mode is selected 24 Switch to the Finger Stylus Pen mode e You are touching the screen board with a part of your hand other than your finger Unable to operate or Use only your drawing finger tip to touch the screen board draw with your finger e The right or left side frame or the reflecting tape inside the lower frame is dirty Use a soft cloth that has been moistened with water and 27 then thoroughly wrung out to gently wipe the dirt off the reflecting tape If the dirt is impossible to remove or if the reflecting tape has been scratched contact your dealer e Magnets or other similar objects have been attached to the screen board 13 Do not attach magnets or other similar objects to the screen Lines or comments board drawn with your finger e An object has been placed on top of the lower frame aremnot shown onthe Do not place any objects on top of the lower frame 13 computer screen P 00 P e The temperature has changed suddenly Refrain from using the elite Panaboard in locations where 17 the temperature is subject to sudden changes Appendix Symptom Possible cause and solution
5. America One Panasonic Way Secaucus New Jersey 07094 Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Panasonic Marketing Europe GmbH For EU onl Hagenauer Strasse 43 65203 Wiesbaden Germany For only For information of Compliance with EU relevant Regulatory Directives Contact to Authorised Representative Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg Germany Panasonic Corporation Web Site http www panasonic net Panasonic System Networks Co Ltd 2012 F0112NS2042
6. See page e The Finger Stylus Pen mode is selected 24 Switch to the Electronic Pen mode The electroni e Other applications or anti virus software are active 5 SS eoon pen oses Shut down the other applications and anti virus software the functions Buttons are e The electronic pen is low on batteries f 28 unresponsive Replace the electronic pen s battery Lines written with the The electroni is inl electronic pen are broken s e Balali i eN PT a e 16 or colors change Turn the selector dial to change the mode e Another electronic whiteboard is in use nearby Change the location of the electronic board so that infrared signals transmitted from electronic pens do not interfere with each other The electronic pen status The electronic pen is low on batteries 28 LED is blinking Replace the electronic pen s battery Because the elite Panaboard is designed exclusively for projector Marks written with a images you cannot erase the marks with a standard eraser whiteboard marker Use neutral household cleaner diluted with water When doing 27 cannot be erased this make sure that no detergent will come into contact with the reflecting tape areas If any contact is made wipe it off quickly 31 32 Appendix Specifications sii UB T580 UB T580W Number General Power Supply from USB bus no AC
7. each Ri e Raise your finger vertically when touching the screen board to avoid other fingers being detected If other fingers are detected the position may get shifted e After you touch an indicated point correctly the next point is shown automatically e When calibration has finished normally a completion dialog box is displayed Calibration Basic Calibration succeeded F Always use this calibration information To further reduce misalignment press the Advanced button and perform Advanced Calibration Advanced If the edges of the image projected on the elite Panaboard are curved click Advanced to perform Advanced Calibration Go to the next step if not required e Advanced Calibration reduces misalignment of a projected image Click OK e f the elite Panaboard and projector are fixed so that they will not move Wall mounted case select the Always use this calibration information check box and click OK to skip calibration from the next time you start the elite Panaboard software Usage Starting the elite Panaboard software When the elite Panaboard software is installed the amp icon is displayed in the notification area when calibration is finished and you can use the elite Panaboard software e To display the Select Function Menu click the Menu Start Tab left side right side on the screen with your finger Example of the Select Function Me
8. unplug the USB cable immediately Contact your dealer for service Operating the contaminated unit can cause fire or electric shock Never open or remove unit covers that are screwed with screws unless specifically instructed in the Operating Instructions A high voltage component can cause electric shock Do not alter the unit or modify any parts Alteration or modification can cause fire or electric shock CHOKING HAZARD Keep the penpoint batteries screws and washers out of reach of small children They might accidentally swallow these items Do not look into the lens while the projector is being used Strong light is emitted from the projector s lens If you look directly into this light it can hurt and damage your eyes Be especially careful not to let young children look into the lens In addition turn the projector off and unplug the power cord when you are away from the projector Electronic Pen Optional Device Battery Using the incorrect type of battery can result in overheating burning or leakage of battery acid Use only the specified type of battery Make sure that the battery is installed with the correct polarity as indicated on the battery holder Incorrectly installed batteries may burst or leak resulting in injuries Do not use the damaged batteries Using damaged batteries may result in leaking Do not charge short heat break or throw in a fire as it may result in the bat
9. 3 For Your Safety For Your Safety Aware To prevent severe injury and loss of life read this Z WARNING section carefully before using the unit to ensure proper and safe operation of your unit Power e This section explains the graphic symbols used in Stop operation immediately if the unit this manual emits smoke excessive heat abnormal smell or unusual noise These Denotes a conditions can cause fire or electric potential hazard shock WARN ING that could resutt Immediately unplug the USB cable and in serious injury contact your dealer for service or death During thunderstorms do not touch the Denotes hazards unit and USB cable It may cause an that could result A CAUTION imino tory of electric shock damage to the unit P Installation and Relocation These symbols are used Have the unit installed removed and t alert pede ion disposed of only by qualified service D specific operating personnel E D must not When the unit will no longer be used in p order to prevent it from falling do not This symbol is used to leave the unit installed but request alert operators to a qualified service personnel to remove specific operating the unit If the unit falls it can cause procedure that must be injury emphasized in order to operate the unit safely For Your Safety Operating Safeguards 86 O If metal fragments or water gets into the unit
10. 3 Ibs Input Unit Screen Board Size 1 175 mm x 1 860 mm Height x Width 3 ft 10 4 in x 6 ft 1 1 4 in Interactive Effective Area 9 16 1 037 mm x 1 845 mm Features Display aspect ratio 3 ft 4 13 16 in x 6 ft 5 a in 83 in diagonal Height x Width 10 16 1 153 mm x 1 845 mm 3 ft 9 3 s in x 6 ft 5 s in 86 in diagonal Appendix Supplies amp Accessories Replace the penpoint with a new one when it is worn and a hole has formed Optional Device Stand KX B061 A Electronic Pen UE 608020 Stylus Pen UE 608021 Up Down Unit UE 608030 Stand Table Unit UE 608031 Short Throw Arm Unit UE 608032 Consumables Penpoint For the electronic pen UG 6020 e To purchase separately sold items contact your dealer 33 Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products packaging and or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste For proper treatment recovery and recycling of old products and used batteries please take them to applicable collection points in accordance with your national legislation and the Directives 2002 96 EC and 2006 66 EC By disposing of these products and batteries correctly you will help to save valuable resources and prevent any potential negative effects on human health and the envir
11. For details about the system requirements refer to Read Me First page 19 in the install menu of the included DVD ROM e Even when the system requirements are met the elite Panaboard response may be delayed or the electronic pen may malfunction if other applications anti virus software etc are active Exemption of Liability Panasonic System Networks Co Ltd is not responsible for accidents or injuries caused by but not limited to the following Altering the device or improper installation construction 2 Using the device for purposes beyond its intended use 3 Earthquake fire flood tidal wave hurricane lightning or other natural phenomena 4 Natural aging of the building or similar phenomena _ Introduction For FRG Users For Germany Only Note Machine noise information regulation 3 GPSGV the maximum sound pressure level is 70 dB A or less in conformity with EN ISO 7779 This device is not intended for use in the direct field of view at visual display workplaces To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view For Ukraine Only Declaration of Conformity with the requirements of Technical Regulation on the Restriction Of the use of certain Hazardous Substances in Electrical and Electronic Equipment adopted by Order N21057 of Cabinet of Ministers of Ukraine The Product is in conformity with the re
12. Panasonic Operating Instructions Electronic Board elite Panaboard Model No U B T580 UB T580W Stand and electronic pen are optional devices e Before operating this unit please read these instructions carefully and keep them for future reference e Please refer to attached Installation Manual Installation performed by non authorized individuals could cause safety related problems with the operation of this equipment For U S A only e To locate the closest authorized dealer in your area please call 1 800 449 8989 Introduction Introduction Thank you for purchasing the Panasonic Electronic Board For optimum performance and safety please read these instructions carefully Feature Highlights You can project your computer screen onto the screen board of elite Panaboard using a projector and perform various operations The main features of elite Panaboard are as follows Touch Features e Manipulate objects on the computer screen by using your finger as a mouse Draw or erase lines on the computer screen by using your fingers Save what you draw on the computer screen as image files Supports Windows 7 multi touch functionality elite Panaboard book Use the elite Panaboard book software that supports elite Panaboard operations such as writing drawing attaching images and computer operations This software lets you save the contents of the screen board on your computer and retrieve it for later use
13. USB bus power operation The elite Panaboard operates on the power supply received via the USB cable connected to a computer There is no need to connect the power cord to an AC outlet Stylus Pen The stylus pen works just like using your finger The finger operation given in this manual also applies to the stylus pen operation Electronic Pen Optional Device e Use the electronic pen to draw or erase lines on the computer screen and to select line colors and other options e Manipulate objects on the computer screen remotely by using the up and down buttons on the electronic pen Usage Scenarios For Education e The elite Panaboard makes it easy to use teaching materials efficiently since it allows you to directly operate various kinds of educational software projected onto the screen board using your finger or to enter text using your finger or an electronic pen e By using illustrations pictures and other tools along with explanations you can encourage your students to actively participate in class through the aid of moving images on the screen board e Draw your students interest by using the screen shade feature to show questions to students while hiding the answers and incrementally showing the rest of the screen e The teacher can prepare materials before class to display on the elite Panaboard For Business e Visually convey your product s characteristics and create an appealing product presentation by displaying images an
14. d using your finger or the electronic pen to highlight key points e Information projected on the elite Panaboard including what you add using your finger or the electronic pen can be displayed in real time at remote locations using videoconferencing equipment Introduction Things you should keep a record of Attach your sales receipt here For your future reference Date of purchase Model no Serial number Dealer s name Dealer s address Dealer s tel no Abbreviations Windows refers to the Microsoft Windows operating system Windows XP refers to the Microsoft Windows XP operating system Windows Vista refers to the Microsoft Windows Vista operating system Windows 7 refers to the Microsoft Windows 7 operating system DirectX refers to the Microsoft DirectX application programming interface Trademarks e Microsoft Windows Windows Vista DirectX Windows Media and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries e IBM is a trademark of International Business Machines Corporation in the United States other countries or both e Intel and Pentium are trademarks of Intel Corporation in the U S and other countries e Adobe Reader and Flash are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countri
15. date Manager If it is necessary to uninstall the Panasonic Software Update Manager follow the procedure below 1 Turn on your computer and start Windows e Log into an account with Administrator privileges 2 Select Add or Remove Programs from the Control Panel e In Windows Vista or Windows 7 select Uninstall a program 3 Select Panasonic Software Update Manager then remove it A Follow the on screen instructions S When uninstallation is complete restart your computer Download the Latest Software Follow the procedure below to download the latest version of the software from the download web site 1 Turnon your computer and start Windows 2 On the Start menu point to All Programs Panasonic elite Panaboard and click Download the latest version Note e If Panasonic Software Update Manager is installed the software update programs are notified over the Internet For details on the Panasonic Software Update Manager operations refer to Panasonic Software Update Manager help For the steps to take refer to Viewing the Help of the Software page 25 Appendix Daily Care When cleaning the elite Panaboard or inside the elite Panaboard make sure to unplug the USB cable from the computer Cleaning the elite Panaboard Replacing the Penpoint of the Clean at least once every three months Electronic Pen Optional Device When the penpoint of the electronic pe
16. e following items are installed in the Panasonic Software Update Manager group They are not displayed if they have not been selected on the Select Features screen in step 7 Panasonic Software Update Manager Help Note e To view the Operating Instructions you must have Adobe Reader installed on your computer If your computer is connected to the Internet you can download Adobe Reader from Adobe s web site Usage Setting the Projector Set up your projector as instructed below About Positioning the Image e When you are using a projector make sure that the projected image is inside the screen board e Do not project an image in the undetectable area oa 1 Undetectable Area Project the Image as a Rectangle e Adjust the location of the projector to project at a right angle with the elite Panaboard e If the image is projected trapezoidally the position may not be read correctly Adjust the projector so that the projected image is a rectangle Refer to your projector s documentation for information on adjusting the projected image SZ LN ZA Set the Proper Resolution e Set your computer s and projector s resolutions to the most appropriate setting If the resolution is not set properly the image will be difficult to see Particularly if the projector s resolution is lowe
17. es e All other trademarks identified herein are the property of their respective owners Introduction Organization of the Manuals The following documents are provided to help you use the elite Panaboard properly and safely In additions to these documents the help information is provided for all software Operating Instructions this document Safety precautions operating procedures and information on after sales service are provided Installation Manual for qualified service personnel Safety precautions on assembly assembly procedure of elite Panaboard and stand and wall mounting construction procedure are provided Help of the Software Instructions for elite Panaboard software and elite Panaboard book included are provided in the help information accompanying the software For details on accessing this information see Viewing the Help of the Software page 25 Federal Communications Commission Requirements For United States Only Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful in
18. es and put in a designated box for collection Contacting with other metals or batteries may cause the battery to leak generate heat rupture or ignite Figure 1 Figure 1 How to isolate a battery Adhesive tape Cc Adhesive tape Do not disassemble remove the battery involucre or deform with pressure Gas generated from the battery may irritate the throat distort the battery seals or cause a short circuit which may lead to leakage heat generation rupture or fire Do not incinerate or heat the battery or expose to a temperature higher than 100 C 212 F Gas generated from the battery may irritate the throat distort the battery seals or cause a short circuit inside the battery which may lead to leakage heat generation rupture or fire Avoid contact with leaking batteries Wash any affected body part with plenty of water Consult a physician in case of irritation 11 12 Usage Included Accessories Check that all of the following items are included with your elite Panaboard In the event that an item is missing please contact your dealer List of Accessories Operating Instructions Software DVD ROM 1 Stylus Pen 1 this document AN Warranty 1 Installation Manual 1 Cable Holder 3 LE Ay Wall Mounting Plate 1 each Pen Holder 2 Screw 7 7 Cable Clamp 1 Flat Washer 4 B
19. g location of your finger or the electronic pen will no longer be aligned with the position projected by the projector requiring recalibration The location of the projector changed The location of the elite Panaboard changed The image area or placement was changed due to changes in the zoom focus etc The resolution of the projector or the computer changed The resolution may be changed when you turn on your computer display e lf you are using the elite Panaboard installed ona stand be aware that accidentally hitting the elite Panaboard or pushing too strongly with the electronic pen while operating can move the stand s position which will result in misalignment of the projected image and the electronic pen s position e Make sure to lock the stand s casters when using the elite Panaboard as failing to do so can cause misalignment Performing the Recalibration Displaying the Calibration Screen Manually e When the elite Panaboard software is already installed Click the A icon in the notification area and click Calibration in the pop up menu e When the elite Panaboard software is not installed Double click the desktop icon of lt elite Panaboard Calibration Tool Exiting the elite Panaboard software Click on the A icon in the notification area and select Exit from the menu Viewing the Help of the Software Follow the procedure below to view the help of the software i
20. he selected color Marker line thickness and other settings can be specified in the Drawing Menu d m Erases marker lines that you have drawn Eraser size and other settings can be specified in the Drawing Menu Eraser LC Highlights with a highlighter in the selected color Yellow Yellowish Highlighter line thickness and other settings can be specified in the Drawing Green Pink Menu Mouse Operates in the same way as using your finger e elite Panaboard software Function selected on the Select Function menu elite Panaboard book Function selected on the tool menu Note e The mouse functions are selected automatically when operation has been switched to the Electronic Pen mode using the Electronic Pen Mode Switching Tool O Low Power Mode Puts the electronic pen in low power mode When not in low power mode the electronic pen detects motion to turn itself on or off automatically To conserve battery power put the electronic pen in low power mode before carrying it while walking when it is not in use Operating ranges of the electronic pen Distance Approx 5m 16 ft 4 in at the front of the elite Panaboard s electronic pen signal receiver when there are no obstructions in between Angle Refer to the figure below The shading represents the operating ranges of the electronic pen Side panel Top panel oo 5m 16 ft 4 in 7 2 E lt x
21. ic pen When performing operations using the electronic pen from a distance point the tip of the pen toward this area and operate For the reception ranges of the electronic pen signal refer to Operating ranges of the electronic pen Rear View page 16 USB Cable Connect the USB plug of the cable to a computer The left figure is an example of a screen board that has the USB cable on its left side The USB cable can be provided on the right side If you want the USB cable on the right side request the qualified service personnel during installation Cable Clamp Use this when bundling the USB cable Pen Holder 2 supplied Holds the stylus pen and electronic pen You can select a desired attachment location among the 4 possible locations Ask the qualified service personnel at the time of installation For details of the attachment location refer to Changing the Attachment Location of the Pen Holders page 28 Notice e The elite Panaboard is designed exclusively for projector images Do not write on the screen board with a whiteboard marker e Do not place any objects on top of the lower frame of the elite Panaboard This can result in erroneous operation e Do not attach magnets or other similar objects to the screen board of the elite Panaboard This can result in erroneous operation Note e The elite Panaboard has detected the position of an obstructio
22. l lights contact your dealer e The elite Panaboard and your computer are not connected Securely connect the USB cable to your computer e The USB cable is connected to a USB hub or extension cable The computer does not Connect the USB cable directly to your computer and not via recognize the elite a USB hub or extension cable Panaboard e A different model was selected when installing the software Select the correct model and reinstall the software e The USB cable is damaged Contact your dealer 19 29 Appendix Symptom Possible cause and solution See page The connection between the computer and the Check that the elite Panaboard is in an operable state and that elite Panaboard is the USB cable is properly connected unexpectedly lost The elite Panaboard Other applications or anti virus software are active 5 response is delayed Shut down the other applications and anti virus software In Windows 7 there is a considerable delay in the The USB operation is erratic Site Paha boat response Unplug and reconnect the USB cable _ when you touch the screen plug i board with your finger e The projected image is misaligned 25 Perform the calibration again e The display resolution pixel count has been changed 25 The point of control is out Perform the calibration again of alignment with your e The edge of the projected image is curved
23. n about 5 mm 0 2 in from the screen board surface Therefore the position may be detected without touching the screen board 13 Usage Stylus Pen The stylus pen works just like using your finger You cannot use both stylus pen and electronic pen simultaneously Strap Loop For attaching straps if desired Use a commercially available strap from which the cord will detach if excessive force is applied Penpoint Notice e When you use a stylus pen make sure to select the Finger Stylus Pen mode using the software page 24 e Use the stylus pen by bringing the penpoint into contact with the screen board The screen board may become dirty if the stylus pen is used by bringing its other end into contact with the screen board surface e Do not tap or knock the screen board with the stylus pen Otherwise it may cause damage 14 Usage Electronic Pen Optional Device Strap Loop For attaching straps if desired Use a commercially available strap A from which the cord will detach if ive force is applied Q excessive A Selector Dial Selects features of the electronic pen Status LED green Lights when the electronic pen power is on J Blinks when the electronic pen battery A y is low Battery Cover A To attach replace the battery see Replacing the Battery in the Electronic Pen Optional Device page 28 Down Button Performs the same function as pressing the Page Down key
24. n starts to wear down a hole will start to form in the penpoint Continuing to use the electronic pen in this condition may cause a scratch or malfunction on the screen board Replace the penpoint with a new one as soon as possible e Replacement penpoints are optional devices page 33 1 Remove the old penpoint and attach the new one Use a soft cloth that has been moistened with water and then thoroughly wrung out to gently wipe off the following areas e The screen board surface e Inside the right and left side frame where the reflecting tape is e Inside the lower frame where the reflecting tape Notice is e Dispose the old penpoint which you have removed following the disposal regulations in Notice your country area e The elite Panaboard is designed exclusively e Ensure that any penpoints which will be used for projector images for replacement purposes are stored in a To remove marks written with a whiteboard safe place marker or stubborn stains use neutral household detergent diluted with water When doing this make sure that no detergent will come into contact with the reflecting tape areas If any contact is made wipe it off quickly e Do not use thinner benzine or abrasive chemicals to clean Doing so can result in discoloration 27 28 Appendix Replacing the Battery in the Electronic Pen Optional Device When the electronic pen battery is low the electronic
25. n the notification area indicates the current mode When you use the electronic pen away from the elite Panaboard press and release the menu mode selector button to switch between the Finger Stylus Pen mode and the Electronic Pen mode Icon and Finger Electronic pen Stylus Pen z Mode operations operations Works just like Pd Can s when you use your finger or the stylus Fi I finger or pen Inger stylus pen ae Stylus Pen operation The selector dial mode functions cannot be used Turn the selector 8 Cannot be dial to select Electronic used electronic pen Pen mode functions Note The operation to enable the electronic pen must be performed for each computer When you restart your computer the mode reverts to Finger Stylus Pen mode To use the electronic pen click the Finger Stylus Pen mode icon in the notification area or press and release the menu mode selector button on the electronic pen To display the Drawing Menu touch the screen board while holding the menu mode selector button on the electronic pen in the Electronic Pen mode Example of the Drawing Menu For detailed information about using the electronic pen refer to the help menu For details on accessing the help information see Viewing the Help of the Software page 25 Usage After Calibration Do Not Move the elite Panaboard or the Projector e If any of the following changes are made the operatin
26. nstalled on your computer 1 Turnon your computer and start Windows 2 Open Software Help from the Start menu Start All Programs Panasonic elite Panaboard Software Help e General help information of the installed software is displayed 3 Open Panasonic Software Update Manager help from the Start menu Start All Programs Panasonic Panasonic Software Update Manager Help e Panasonic Software Update Manager help is displayed Note e To access the help information of elite Panaboard software Stylus Pen and Electronic Pen click the A icon in the notification area and select Help from the pop up menu e To access elite Panaboard book help information select Help from the elite Panaboard book Help menu e We recommend that you view the help using Internet Explorer 6 0 or later for Windows 25 26 Usage Uninstalling the Software If it is necessary to uninstall the elite Panaboard driver software book follow the procedure below 1 Turn on your computer and start Windows e Log into an account with Administrator privileges 2 Select Add or Remove Programs from the Control Panel e In Windows Vista or Windows 7 select Uninstall a program 3 Select Panasonic elite Panaboard then remove it 4 Follow the on screen instructions 5 When uninstallation is complete restart your computer Uninstalling Panasonic Software Up
27. nu Note e When the elite Panaboard software is not installed the Z4 icon is not displayed in the notification area The Menu Start Tab is not displayed on the screen Starting the elite Panaboard book The elite Panaboard book can be started in the following ways e If the elite Panaboard software has been installed click the 3 icon in Select Function Menu e Double click the desktop icon of i elite Panaboard book e Click Start All Programs Panasonic gt elite Panaboard elite Panaboard book 23 24 Usage Using the Electronic Pen Optional Device When using the electronic pen for the first time establish the Electronic Pen mode by taking the steps below 1 Confirm that the elite Panaboard driver software book is installed on your computer and connect the UB T580 UB T580W to your computer 2 Press and release the menu mode selector button while pointing the penpoint toward the elite Panaboard s electronic pen signal receiver next to the status LED in the upper left part of the main unit e The a icon which indicates Electronic Pen mode is displayed in the notification area of the computer screen and you can use the electronic pen After establishing the mode by taking the steps above click the icon in the notification area of the computer screen to switch from Finger Stylus Pen mode F to Electronic Pen mode to use the electronic pen The icon displayed i
28. nu exe 3 When the elite Panaboard screen is displayed click the type of device you are using 4 When the Menu screen is displayed click Read Me First ME Menu UB T580 Ver x xx Read Me First e After the system requirements are displayed make sure that your computer meets the requirements Click Install elite Panaboard on the Menu screen If you agree to the terms in the END USER LICENSE AGREEMENT select l accept the terms in the license agreement and then click Next e In Windows Vista if the User Account Control window is displayed click Continue to continue with the installation e In Windows 7 if the User Account Control window is displayed click Yes to continue with the installation When the Select Features screen is displayed select the required function or deselect a function that you do not want and then click Next e Click the corresponding check box to select or deselect a function e You cannot deselect a function that is shown with a gray check box because it is a mandatory function e When you deselect a function that is already installed this function will be deleted uninstalled e If Panasonic Software Update Manager is already installed it will not be deleted uninstalled even when it is deselected For details on how to uninstall it refer to Uninstalling Panasonic Software Update Manager page 26 19
29. on a computer by remote control P int Up Button enpoin Performs the same function as pressing the Page Up key on a computer by remote control Menu mode selector button Hold this button and touch the screen board with the pen to display the Drawing Menu page 24 Press and release this button away from the elite Panaboard to switch between the Finger Stylus Pen mode and the Electronic Pen mode page 24 Notice e When operating the electronic pen s up button down button or menu mode selector button point the penpoint at the elite Panaboard s electronic pen signal receiver and operate the button For the operating ranges of the electronic pen refer to Operating ranges of the electronic pen page 16 e To use the electronic pen switch to the Electronic Pen mode using the software To use your finger switch to the Finger Stylus Pen mode e Confirm that the status LED lights when using the electronic pen e To avoid operating errors do not touch the penpoint when the electronic pen is not in use e Use the electronic pen by bringing the penpoint into contact with the screen board The screen board may become dirty if the electronic pen is used by bringing its other end into contact with the screen board surface e Do not tap or knock the screen board with the electronic pen Otherwise it may cause malfunction 15 Usage Electronic Pen Features E Black Red Blue Green Draws with a marker in t
30. onment which could otherwise arise from inappropriate waste handling For more information about collection and recycling of old products and batteries please contact your local municipality your waste disposal service or the point of sale where you purchased the items Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union These symbols are only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Note for the battery symbol bottom two symbol examples This symbol might be used in combination with a chemical symbol In this case it complies Cd with the requirement set by the Directive for the chemical involved Information on Disposal for India For the purpose of recycling to facilitate effective utilization of resources please return this product to a nearby authorized collection center registered dismantler or recycler or Panasonic service center when disposing of this product Please see the Panasonic website for further information on collection centers etc http www panasonic co in wps portal home Panasonic Corporation of North
31. or electric shock Do not lean against the unit even if the unit is mounted on the wall When using the stand be sure to watch your step so that you do not bump into or trip over the fall prevention extension legs The label of precautions is attached to the stand KX B061 A optional device When operating the screen board with your finger for a long time be sure to take regular breaks Continuous use for a long time may hurt your fingertip For Your Safety Precautions Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device About Using the Battery If a battery is used improperly the battery may leak causing corrosion of the unit or it may burst To prevent this always follow the precaution given below e If the electronic pen ceases to function because the battery has run out remove it immediately and dispose of it according to local regulations Leaving a drained battery in the electronic pen may result in leakage About Disposing of the Battery of the Electronic Pen Optional Device For Taiwan Gy Og Fees than UK Handling of End of life Batteries For Brazil only BRASIL Ap s o uso as pilhas e ou baterias poder o ser entregues ao estabelecimento comercial ou rede de assist ncia t cnica autorizada Wrap adhesive tape around the end of life battery to isolate the and polariti
32. pen status LED blinks green Continued use of the electronic pen can lead to poor performance Replace the battery as soon as possible 1 Unlock the battery cover and open the cover F 2 Insert replace the battery e Make sure to use a AAA alkaline battery and ensure that and face the correct directions e Dispose of expired batteries quickly by covering the terminals in tape and following the disposal regulations in your country area 3 Close the battery cover and lock the cover using the procedure of step 1 in reverse order Changing the Attachment Location of the Pen Holders When the stand is used you can change the attachment location of the pen holders See Names and Uses of the Parts page 13 for details Necessary Tool Phillips head screwdriver CAUTION Before changing the attachment location lock the casters and ensure that the location is changed by two persons Otherwise this unit may move or fall down and cause injury 1 Remove the pen holder that you want to move e Remove the 2 screws for the pen holder from the back of the main unit 2 Select a desired attachment location among the 4 possible locations Appendix Troubleshooting When experiencing problems please refer to the table below for possible solutions If the problem persists contact your dealer In the case of the kinds of tro
33. power supply connection required Power Consumption 5 V 500 mA USB bus power Operating Environment Temperature 10 C to 35 C 50 F to 95 F Humidity 30 to 80 Storage Environment Temperature 20 C to 60 C 4 F to 140 F Humidity 20 to 80 Interface USB 2 0 Electronic Transmission System Infrared communication system Pen F Optional Electronic Pen Power LRO3 AAA alkaline dry cell battery x 1 Device Electronic Pen Battery Life 30 hours when used continuously at 25 C 77 F When using Panasonic LRO3 alkaline dry cell batteries Model Number UB T580 General External Dimensions 1 352 mm x 1 637 mm x 74mm Height x Width x Depth 4 ft 5 1 4 in x 5 ft 4 16 in x 2 15 16 in When pen holders have been attached on both sides of the main unit 1 352 mm x 1 713 mm x 74 mm 4 ft 5 1 4 in x 5 ft 7 The in x 2 1 16 in Weight 23 kg 50 7 Ibs Input Unit Screen Board Size 1 175 mm x 1 582 mm Height x Width 3 ft 10 1 4 in x 5 ft 2 5 16 in Interactive Effective Area 3 4 1 175 mm x 1 567 mm Features Display aspect ratio 3 ft 10 1 4 in x 5 ft 1 16 in 77 in diagonal Height x Width Model Number UB T580W General External Dimensions 1 352 mm x 1 915 mm x74 mm Height x Width x Depth 4 ft 5 1 4 in x 6 ft 3 3 s in x 2 15 16 in When pen holders have been attached on both sides of the main unit 1 352 mm x 1 991 mm x74 mm 4 ft 5 1 4 in x 6 ft 6 3 s in x 2 15 16 in Weight 26 kg 57
34. quirements of Technical Regulation on the Restriction Of the use of certain Hazardous Substances in electrical and electronic equipment TR on RoHS The content of hazardous substance with the exemption of the applications listed in the Annex N22 of TR on RoHS Lead Pb not over 0 1wt or 1000wt ppm Cadmium Cd not over 0 01wt or 100wt ppm Mercury Hg not over 0 1wt or 1000wt ppm Hexavalent chromium Cr not over 0 1wt or 1000wt ppm Polybrominated biphenyls PBBs not over 0 1wt or 1000wt ppm Polybrominated diphenyl ethers PBDEs not over 0 1wt or 1000wt ppm OaRWN Table of Contents Table of Contents For YOUP Safety c2ccececcteccceveisccessecencesscsesceccenedccideeedeeeseeetireciegeensenecesateniettetne 8 FOr Your Safety wciccccccccccccccceeccosssivee ste cceenecttcccnneueetteceeseetocedeees ctacernes OERE ARRENE E 8 PFO CAUTIONS asessorina areenaa EE aE a eaa EETA EEEE 11 WETE Ke e aac E A ee cece 12 Included Accessories siicicsscctcticceceecdtecceeesdcteceeeestteceeeesttenceeenstteceeeestteedeeeeettvccuntestoteess 12 Names and Uses of the Parts ccccccesseeeeeeeeeeeeeeeeeeeeeeeeeeseeseeeeeeseeeeeeeeseeeeeeeeeeeeseenes 13 Connecting External COMPONENES cccccceseeeeeeeeseeeeseeeeseeeeseeeeseeeeeseeesseeseeeeeseeenens 17 Installing the Software ccccseeeeeeeneeeeeeeeeeseeeeeeseeeseeeeeseeseeeeeeenseeseeneeseseseeeesneeeeeeeenes 19 Set
35. r than the computer s thin lines can appear cut or broken Refer to your projector s documentation for information on adjusting the resolution Do Not Look Directly into the Projector Lamp e When using a projector try to avoid looking directly into the projector lamp Doing so can hurt your eyes 21 22 Usage Using the elite Panaboard After Positioning the System Calibration About Calibration Calibration refers to setting up the elite Panaboard and projector so that lines and comments drawn with your finger or the electronic pen are displayed in the correct position Be sure to perform calibration before use After you have set up the elite Panaboard project an image onto the screen board and use the elite Panaboard software installed on your computer to perform calibration Performing Calibration When the elite Panaboard is connected to your computer the calibration screen is automatically displayed Note e When using the projection screen of a projector to which the HD Visual Communication Unit has been connected refer to the help menu For details on accessing the help information see Viewing the Help of the Software page 25 1 Connect the elite Panaboard to your computer with the USB cable e The calibration screen is displayed 2 Calibrate the equipment by using your finger to touch the center of the indicated points following the instructions on the screen for about 2 seconds
36. te Panaboard in a location less than 10 C 50 F or in a location subject to extreme changes in temperature Note e The elite Panaboard may not work properly when used in one of the above locations 17 Usage Moving the elite Panaboard When Using the Stand Optional Device 1 Disconnect the USB cable and bundle it using the cable clamp 2 Release the locks on the casters Note e When folding back the fall prevention extension legs release the lock as follows 3 Move the elite Panaboard with 2 people avoid banging or shaking the board Notice e Do not drag or step on the cable 4 Lock the casters 5 Pull the fall prevention extension legs down 18 Usage Installing the Software To install the elite Panaboard driver software book follow the procedure below Notice e Do not connect the USB cable to the computer until the installation is completed e Do not connect more than 1 elite Panaboard to the same computer Doing so can cause erroneous behavior on the computer 1 Turnon your computer and start the Windows operating system e Log into an account with Administrator privileges 2 Insert the included DVD ROM into the DVD ROM drive e The setup screen will be displayed e lf the setup screen does not appear select your DVD ROM drive in Explorer and double click Menu exe e In Windows Vista or Windows 7 if the Autoplay dialog box is displayed click Run Me
37. terference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Warning operate this device To assure continued FCC compliance the user must use only shielded interface cable Also any unauthorized changes or modifications to this equipment would void the user s authority to Introduction Warning about saving data When the system storage device or any of its optional storage device is adversely effected by operational errors static electricity electrical noise vibration dust or when the power has been cut off due to malfunction repair or inadvertently the memory contents may be lost or changed Before operating the system make a point of reading the precautionary notes in the Operating Instructions and the help information and observe them during operation Please observe carefully the following precaution e Make absolutely sure that all important data is saved by back up or the original is saved The manufacturer hereby declares that it cannot be held accountable for any loss or change in any data stored on floppy disks hard disks optical disks or other memory devices System Requirements Computer IBM PC AT compatible with a DVD ROM drive CPU Intel Pentium 4 processor or later Interface USB 2 0 Note e
38. tery leaking generating heat or bursting When disposing of the battery cover the battery contacts with insulation ex tape Direct contact with other batteries may result in leaking fire or explosion Do not solder the battery as it may result in the battery leaking generating heat or bursting Remove empty batteries immediately to avoid battery fluid leakage Avoid contact of battery fluid with eyes skin or clothing as this may result in irritation or injury In these cases do not rub the affected area and rinse thoroughly with clean water 90 10 For Your Safety CAUTION Installation and Relocation SO 0 OO Do not position the unit in a location where it is unstable Do not place the unit in a hot humid or dusty environment Prolonged exposure to these adverse conditions may cause fire or electric shock To prevent fire or shock hazard do not expose this unit to rain or any type of moisture When moving the unit be sure to unplug the USB cable Otherwise you may trip over a USB cable which may cause injury Move this unit with two persons Otherwise this unit may fall down and cause injury After installing or moving the unit lock the casters and set the fall prevention extension legs Locking the casters Push to lock 5 N 000 Operating Safeguards If the unit falls down or gets damaged unplug the USB cable Otherwise it may cause fire
39. ting the Projector ees sasceeis saissceeies settee ecaceeines de cuueek eas doce aes SSAKA KANAAN ARESA Ran 21 Using the elite Panaboard After Positioning the System Calibration 22 Viewing the Help of the Software ccccccessseecceeeseneeeeeeeeneeeeeeeseeneeeesseeeeeeenseeeeeeeeenss 25 Uninstalling the Software cccccseeecseseeeeeeeeeeeeeeeneneeneeseeseeeeeeseeeeeseeeesesesseeeseeeeeseeeeens 26 Uninstalling Panasonic Software Update Manager scccccssseeeeeeeeeseeeeeeeneseeenens 26 Download the Latest Softwar e ccccccsssseeeeeeesseeeeesseeeeeeneeseeeeeeeesseeeeeeeesseeeeeeeeeesenes 26 AppendiX seinci aera ae ea Sense See eos mt oe i ne e eeeeeee ieee eee ere 27 Daily Cane eussi nia aE AS ELERS EROAN 27 Cleaning the elite Panaboard aeessseesesrneseesnnennssnnaaarnnnnaatannnaannnnnnattannadnnnnnaattannaa 27 Replacing the Penpoint of the Electronic Pen Optional Device ceeee 27 Replacing the Battery in the Electronic Pen Optional Device 28 Changing the Attachment Location of the Pen Holders c cceeecseeeeeseteeeeeeenees 28 Troubleshooting s ccicccecsteccceccrtesccceeeeiteccticertesccceeeettevecanenteeccassaistessdawertaeetziccieeeestasecreess 29 Specifications i 3cinsccnntecensiensssevennnndencsvesnna aaaea Naaa aeaaea Aaa aana Eaa aeaa Anaan anana Aidian 32 Supplies amp ACCESSOreS ccccccccecceceeeeeeeeeeeeaecaeceeeeeeeeeeeeeaaanaeceseeeeeeeeeseesesneeaees 3
40. uble which are not described in the table below refer to Troubleshooting in the software help See Symptom Possible cause and solution page The Status LED does not Check that the USB plug is properly plugged in light when the USB cable Unplug the USB cable wait at least 5 seconds and plug it in is connected again If the status LED still fails to light contact your dealer e The right or left side frame or the reflecting tape inside the lower frame is dirty Use a soft cloth that has been moistened with water and then thoroughly wrung out to gently wipe the dirt off the reflecting tape If the dirt is impossible to remove or if the reflecting tape has been scratched contact your dealer 27 e Magnets or other similar objects have been attached to the screen board Do not attach magnets or other similar objects to the screen board The Status LED red e An object has been placed on top of the lower frame lights Do not place any objects on top of the lower frame 13 13 e You connected the USB cable while touching the screen board When you connect the USB cable do not touch the screen board e The temperature has changed suddenly Refrain from using the elite Panaboard in locations where 17 the temperature is subject to sudden changes After taking the above steps unplug the USB cable wait at least 5 seconds and plug it in again If the status LED red stil
Download Pdf Manuals
Related Search