Operating Instructions for ClassicLine / PremiumLine
Contents
1. safety eye showers In order to start the eye shower press the big PUSH lever This locks the PUSH lever in the open position The eyewash should not make direct contact with the contaminated eye or any surrounding areas Ideal rinsing is as sured at a distance of approximately 150 mm In order to stop the shower pull back the PUSH lever Contact a doctor DENIOS AG a Dehmer Stra e 58 66 32549 Bad Oeynhausen p Tel 49 0 5731 7 53 0 Fax 197 info denios com www denios com 9 Maintenance Problems The safety shower must be checked for visible damage or faults after installation and before being put into use and subsequently at the intervals stated and after any alterations or maintenance 9 1 Maintenance The safety showers must be checked for operation at least once a month This is also set out in the BGI GUV I 850 0 guidelines from BG Chemie For this purpose the shower must be turned on for approximately 5 seconds This not only checks the operation of the shower itself but also replaces the water in the shower with fresh water contamination protection During the course of this test the shower is to also be inspected visually to see how it closes and if any leaks or dirt such as dust or limescale are apparent Faulty parts must be replaced immediately 9 2 Problems Problem Possible cause Possible solution The amount of water coming out of the Water pressure or cross section of the Check the piping Ens2. DENIOS AG o Dehmer Stra e 58 66 32549 Bad Oeynhausen a Tel 49 0 5731 7 53 0 Fax 197 info denios com www denios com CAUTION For new installations the water supply system must be rinsed out before connecting the shower in order to prevent dirt damaging the valve Complaints arising from pipeline which has not been rinsed out cannot be accepted see point 5 1 Standards and regulations The safety showers comply with all aspects of DIN 12899 3 2009 DIN EN 15154 1 2006 ANSI Z358 1 2009 TRGS 526 and the BG Chemie BGI GUV I 850 0 guidelines This operating manual serves as a supplement to the valid rules and regulations Please take note of the DIN 12899 3 2009 DIN EN 15154 1 2006 ANSI Z358 1 2009 TRGS 526 and the BG Chemie BGI GUV I 850 0 guidelines 2 Operating pressure The safety showers are covered for an operation pressure of a maximum of 10 bar PN 10 The safety showers commands about an automatic flow regulator of 50 1 min category in accordance with DIN 12899 3 2009 The flow rate amounts 45 till 55 litre minute Independent from the upcoming operative pressure this flow rate will be automatically centred by a flow regulator 3 Construction Where possible the safety showers are to be stored and delivered in the transport packaging box pallet sup plied and kept in dry and frost free conditions The surface must be level and be able to hold the weight of the safety shower when installed and filled
3. Walls and special structures must be able to hold the weight of the safety shower and the piping Any water leaking from the safety shower during use should not be able to cause any consequential damage Lea king water is to be safely drained away using barriers and drain trays if necessary bed notd eng DENIOS AG Dehmer Stra e 58 66 32549 Bad Oeynhausen Tel 49 0 5731 7 53 0 Fax 197 info denios com www denios com 3 1 Water connection The connections for the various safety showers have a to 1 4 thread We recommend attaching the safety shower to at least a inch pipe The water pressure should be at least 1 bar The water supply for the safety sho wer should be situated near the system and have a stop valve for maintenance and repair work that no one can tamper with 3 2 Necessary space installation height of body safety showers There must be a free space with a radius of 400 mm underneath the body safety shower The installation height in accordance with DIN EN 15154 1 2006 of the lower edge of the shower head body safety shower must be 210 230 cm 3 3 Necessary space installation height of eye showers There must be a free space with a radius of 150 mm around the eye shower The installation height in accordance with DIN EN 15154 2 2006 of the upper edge of the spray head eye shower must be 80 120 cm 3 4 Installation height of safety shower valve release button The safety shower valve relea
4. se button should be mounted in a maximum height of 175 cm above the floor in the immediate vicinity of the safety shower 4 Installation 4 1 Installation of wall ceiling mounted versions Wall or ceiling mounted versions must be securely fastened to the wall ceiling or other special structure The technique required to fasten the shower depends on the construction and is to be decided by the installation com pany 4 2 Installation of over door mounted versions The over door models are delivered with an already attached valve adapter type A for installation of the rod ope rated valve to the right of the door If an installation to the left of the door is required then the attached valve ad apter type A must be replaced by another valve adapter type B which is also included in the delivery The specialist tool C31 which is also included in the delivery must be used to attach the valve adapter to the ball cock The nut of the ball cock must be tightened with a standard screw locking device 4 3 Installation of freestanding body safety showers Freestanding body safety showers must be securely fastened to the surface using the base plate The technique required to fasten the shower depends on the construction and is to be decided by the installation company DENIOS AG Dehmer Stra e 58 66 32549 Bad Oeynhausen Tel 49 0 5731 7 53 0 Fax 197 info denios com www denios com 5 Water supply The body safety showers mus
5. t be connected to drinking water The drinking water network must be set up in ac cordance with DIN 1988 and DIN EN 1717 CAUTION For new installations the water supply system must be rinsed out before connecting the shower in order to prevent dirt damaging the valve The high performance shower head must be deinstalled during this pro cess It must be reinstalled after the rinsing process 6 Safety labelling The enclosed safety label self adhesive label is to be attached near the body safety shower 7 Location The location is to be chosen in accordance with the BG Chemie BGI GUV 850 0 guidelines Access must always be kept clear Special care must also be taken at the installation location that the safety shower cannot be damaged by vehicles e is readily accessible to users at all times e is less than 10 metres away from the potential danger zone and can be reached within 10 seconds e For highly corrosive substances a distance between 3 6 metres is recommended The area around the shower must be well lit and the shower itself must be clearly identified by easily visible signs 8 Operating 8 1 Body safety showers with pull rods Pull the handle until the valve arm stops Once showering begins remove all contaminated items of clothing that are not stuck to the skin and rinse all affected areas with clean and cold water Push the lever upwards until the valve closes to turn off the shower Contact a doctor 8 2 Models with
6. ure that the pi shower does not appear to be sufficient connecting pipes is too low ping has a minimum diameter of in ches and that the water pressure is at least 1 bar The volume of water which flows from Water pressure is too low supply line Unscrew the jet regulator and clean the eyewash does not appear to be ade cross section is too small or the jet re the regulator and sieve blue If water quate gulator is contaminated pressure is too low low pressure diffu sers are available as accessories The shower drips continuously The valve does not close properly Check the valve for damage and en sure that the valve is pushed back into a fully closed position The shower drips continuously The valve seal is damaged Replace the valve The body safety shower does not auto This is NOT a fault This is a require This is NOT a fault This is a require matically switch itself off after use ment according to DIN standards ment according to DIN standards 10 Disposal The safety shower can be fully dismantled The individual parts e g metal insulation etc can be recycled se parately Please note the national and international disposal regulations Operating Instructions ClassicLine PremiumLine Safety Showers B SAFETY 01 2012 bed notd eng
Download Pdf Manuals
Related Search