Paslode 902000 Instructions / Assembly
Contents
1. 12 As you slide the metering valve fuel cell assembly into the Cordless Finish Nailer you will notice a yellow adapter at the top of the cylinder pocket As shown in the illustration this adapter is designed to ensure that the metering valve stem is properly aligned with the small hole or orifice that leads to the combustion chamber Insert the metering valve stem into the orifice of the yellow colored adapter Yellow Adapter Fuel Cell Metering Valve Stem Close the actuator cover to complete the loading of fuel in the Cordless Finish Nailer Do this by swinging it up and over the metering valve fuel cell assembly and pushing down until the actuator cover snaps into position i 2 PUSH DOWN Eg fi Sin i il Pl Gi a Sige e Surgit mM INE a 3 3 Fasteners The Paslode Cordless 16 ga Straight Finish Nailer drives Paslode 16 gauge straight fasteners designed to be used with the tool The use of fasteners that do not meet Paslode standards could cause tool damage and will void all warranty claims Loading Fasteners Step 1 Insert one or two strips of Paslode16 Gauge Straight Finish Nails into the rear of the magazine and slide forward Step 2 While applying pressure to the release lever pull the follower toward the rear of the maga2. Clear jam Tool operates erratically or appears to be losing power tool indicator light is green Fuel cell is low Check fuel cell Spark plug wire is loose Check spark plug wire Air filter is dirty causing tool to overheat Remove air filter and clean Use soap and water to remove stubborn debris Tool is dirty Clean tool Tool operated and drove fasteners but driver blade did not return to up position Built up dirt and debris on driver blade or in nose bore Clean driver blade and nose bore with degreaser cleaner Tool is dirty Clean tool Combustion chamber does not drop after tool cycles Work contacting element is bent or is dirty Clean track or replace work contacting element If tool will not operate after following the above service directions return the tool to an authorized Paslode representative for service For the nearest Paslode representative call 1 800 682 3428 For Technical support call 1 800 222 6990 Paslode An Illinois Tool Works Company 888 Forest Edge Drive Printed in U S A Vernon Hills Illinois 60061 2004 Illinois Tool Works Inc www paslode com 902017 1 8 04
3. TOOL CLEAN A clean tool is less likely to jam or malfunction 18 KEEP YOUR HANDS CLEAR OF THE WORK AREA SURFACE A WARNING A fastener may exit at an angle unexpectedly and cause injury The Paslode batteries contains cadmium and must be recycled or disposed of properly It is illegal in some areas to place a nickel cadmium battery into the trash or solid waste stream You may contact your local recycling center for information on where to return the spent battery or call 1 800 822 8837 for information on Ni Cd battery recycling in your area Battery and Charging System Battery and Charging System The Paslode Cordless tools come with a recharge able battery and its own charging system This charging system is the only one that will work with the Paslode batteries either round or oval The first step in preparing a new tool for operation is to fully charge the battery New batteries are shipped discharged and must be charged prior to first use Batteries will take 5 minutes to 2 hours time will be dependant on the amount of discharge of the battery to recharge Important Charging Notes A Warning CHEMICAL EXPLOSION HAZARD Read ALL instructions be fore charging or using bat tery Failure to follow ALL instructions may result in fire severe burns or re lease of toxic materials Battery Disposal The Paslode batteries contain cadmium and must be recycled or dispose
4. continuous operation Whenever the Cordless Finish Nailer is idle for extended periods keep the fuel and tool out of direct sunlight and in surroundings where temperatures will not exceed 120 F 49 C After extended periods of continuous use it may be necessary to cool the motor by setting tool aside for 10 15 minutes or until the tool operates normally An overheated tool may not drive nails completely or may operate erratically COLD WEATHER OPERATION Fuel cells at cold temperatures lose the required propellant pressure Bring the tool fuel cell and battery above 20 F 7 C by placing the tool in a heated building or vehicle Never expose the tool fuel cell or battery to flame A CAUTION The Cordless Finish Nailer should not be used in the rain or where excessive moisture is present The use of Paslode Cordless Technology under these conditions may result in damage to tool components and cause the tool to malfunction Preparing the Paslode Cordless 16 ga Straight Finish Nailer Paslode Cordless 16 ga Straight Finish Nailer Operation Operation PRESS WORK 7 CONTACTING ELEMENT AGAINST THE WORK SURFACE Fan motor starts fuel is injected into combustion chamber and mixed with air by the fan SQUEEZE TRIGGER Spark plug ignites the fuel air mixture driving the piston assembly down on the fastener RELEASE TRIGGER LIFT TOOL C
5. is no more fuel left in the cylinder and it must be replaced Dispose of the empty fuel cell properly see page 16 Clearing a Jam An occasional problem you may encounter is a jammed fastener Because of the unique design of the Cordless Finish Nailer clearing a jammed fastener is easy 1 Remove the battery 2 Pull the latch releasing front guide Pivot front guide forward 3 Clear jam and push driver blade back up to its normal position 4 Close frontguide and latchit Check that work contacting element moves freely Air Filter Open the cover by pressing slightly above the adapter and pivoting the cover open The air filter simply lifts out Tap the filter GENTLY to remove any dust Check and clean the air filter every two days Soap and water restores the filter to a like new condition FILTER End of Workday Routine These simple steps are based on maintaining the safety and operational efficiency of the Cordless Finish Nailer Before you leave the work site 1 Remove battery and store in tool case Always use the Cordless Finish Nailer case for transporting and storing the tool 2 Dispose of all empty fuel cells Remember to dispose of these cells where they will not be crushed punctured burned or found by children Servicing When you get home 1 Place the
6. ATE THE TOOL ONLY ON THE WORKPIECE A WARNING The Cordless Finish Nailer should be operated only when it is in contact with the work surface When fastening thin materials be sure to position the tool so that the fastener is driven into the underlying piece 12 NEVER DRIVE FASTENERS INTO AREAS WITH CONCEALED HAZARDS 13 Always check the area behind the work surface for electrical wiring gas pipes water pipes sewer drains or other potential hazards ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED FOOTING WHEN ON LADDERS PLATFORMS OR OTHER HIGH LOCATIONS A WARNING Never over reach since tool recoil may cause a loss of balance Always be aware of edges and drop offs when nailing on rooftops and other high locations Keep them in full view Safety Instructions 15 PROPERLY STORE FUEL CELL A WARNING Always store fuel cells where they will not be exposed to an open flame sparks or temperatures above 120 F 49 C 14 ALLOW ONLY QUALIFIED PERSONNEL TO OPERATE THE CORDLESS FINISH NAILER A WARNING Only persons who have read and fully understand all tool operation safety and maintenance instructions shouldbe allowed to operate the tool Battery Disposal 16 ALWAYS STORE THE TOOL WITH THE FUEL CELL AND BATTERY REMOVED Store the fuel cell in the case with the Cordless Finish Nailer 17 KEEP THE
7. CORDLESS 16 GAUGE STRAIGHT FINISH NAILER OPERATING MANUAL IMPORTANT DO NOT DESTROY It is the customer s responsibility to have all operators and service personnel read and understand this manual www paslode com Contents Subject Page Introduction and Warranty secs cisnienia aa Aa ER ANRO 2 An Overview of the Paslode Cordless 16 Gauge Straight Finish Nailer 3 Eia INStuctions LE 4 Battery and enr 7 Fuel Cell and Metering Valve esssessesesseeeeeeeneeneeenenennen nennen nnne nennen nennen nnne 9 Preparing the Paslode Cordless 16 Gauge Straight Finish Nailer for Use 12 Paslode Cordless 16 Gauge Straight Finish Nailer Operation seessssssss 13 Fasteners and Applications cc cccccscceceeeceeeeeeeeeeeeceeeeeesecneeeseeeesecaeeeseaeeeseseeeessaeeeseneeess 14 SOIVICING e 15 uiieileiee RM ET 17 The battery charger system meets all safety requirements for power tools 0 z Paslode s a rademark CEGE An linois Tool Works Company 888 Forest Edge Drive Vernon Hills Illinois 60061 www paslode com P Paslode Power Nailers are made in the U S A and are protected by one or more of the following U S patents 4 403 722 4 483 280 4 483 474 4 522 162 Other patents issued and pending Paslode is a member of Bad ISANTA Copyright 2004 Illinois Tool Wo
8. IMPORTANT Should your battery terminals become corroded and cause poor electrical contact clean the terminals using a soft cloth Clean the contacts Battery and Charging System Battery Indicator Light On the right side of the handle is a small plastic lens This is the battery indicator light When you inserta fully charged battery into the tool you will see a blinking green light If the indicator light blinks red recharge the battery lp Straight Fuel Cell and Metering Valve Fuel Cell A DANGER EXPLOSION FIRE HAZARD Read ALL safety instructions before using or handling the fuel cell Failure to follow ALL instructions may result in explosion or fire This may cause severe personal injurieS or property damage Keep the fuel cell away from heat sparks and open flame Exposure to temperatures above 120 F 49 C may cause the fuel cell to burst releasing flammable gas A WARNING valve Do not inhale the spray Sunlight can raise the inside temperature of an unventilated car or van to above 140 F 60 C Do not puncture or attempt to open the fuel cell it is non refillable Do not incinerate reclaim or recycle the fuel cell Do not smoke while installing or operating the metering Keep out of the reach of children Store fuel cell s in well ventilated areas only The
9. an operates and the indicator light is green but the tool will not cycle or does not drive fasteners completely check the fuel cell With the fuel cell out of the tool check to see if the cell still contains fuel and that the metering valve is working To determine if there is any fuel left in the fuel cell hold in the upright position and simply place the metering stem against a solid object and gently push about three or four times A small amount of fuel should be released each time A DANGER Wear safety glasses when performing this test Never perform this test near an open flame or sparks while smoking or where the fuel may get into your eyes A DANGER Never attempt any maintenance of a Paslode Cordless tool without first removing the fuel cell and battery Maintenance should be started only after the tool is completely inoperative Battery Check Periodically check on the battery indicator light the light in the handle of the Cordless Finish Nailer When encountering a problem the first step should always be to make sure the battery has enough charge to operate the tool When the work contacting element is depressed on the work piece the fan motor will turn on and the blinking green indicator light will turn solid green If the indicator light blinks red or glows red recharge the battery 16 If fuel is not released with each operation of the metering valve this indicates that there
10. battery in its charger if it needs charging as indicated by the red charge light on the handle 2 Wipe your Cordless Finish Nailer with a clean soft cloth 3 Remove and clean the filter every two days 4 Checkworkcontacting elementto ensure it is operating freely Paslode Cordless Tool Accessories A variety of accessories are available for the Paslode Cordless 16 Gauge Straight Finish Nailer No Mar Tip 3 Pk Part No 219236 Battery Part No 404717 Degreaser Cleaner Part No 219086 9 64 Hex Key Part No 900736 Tinted Safety Glasses Part No 402512 Clear Safety Glasses Part No 402510 Bumper Removal Tool Part No 900760 Paslode Cordless Lubricating Oil Part No 401482 Battery Charger Kit Part No 900200 Automotive Adapter Part No 900507 Paslode Cordless Finish Nailer Carrying Case Part No 900751 High Altitude Valve Kit Part No 219247 For fuel cells at altitudes from 4 000 to 9 000 feet Contact your Paslode representative for additional information Tools A 9 64 Hex Wrench Part No 900736 is provided with each Cordless 16 Gauge Straight Finish Nailer Troubleshooting Preparing Tool for Operation Battery Charger Problems SYMPTOM POSSIBLE PROBLEMS SERVICE Battery does not appear to accept charge when battery is plugged into the charger Inoperative indicator lights on charger or defective charger Try battery in tool after a full charge cycle If
11. cycle rate you will be able to drive several thousand nails in a typical workday Fasteners 16 Gauge Straight Magazine Capacity 2 nail strips or 110 fasteners Battery 6 volts DC Provides enough energy to drive approximately 4000 fasteners ona full charge Fuel Cell Short yellow fuel cell 640z part no 650039 Liquid hydrocarbon Provides enough fuel to drive approximately 1200 fasteners fuel cell compartment Handle Assembly soft grip reversable belt hook Magazine Assembly battery indicator light opposite side G 3 adjustable lt E E PASLODE 16 Gauos te FINISH NAILS ONLY X nail count indicator battery compartment depth of drive opposite side nose P follower work contac no mar tip opposite side element The following safety instructions have been included in this booklet to provide you with basic information necessary for safe operation of the Paslode Cordless 16 ga Straight Finish Nailer DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS Safety Instructions AX Dancer The Cordless Finish Nailer is an internal combustion device It produces hot exhaust gases that may ignite flammable materials This tool must not be used ina combustible environment or in the presence of combustible materials such as fla
12. d of properly It is illegal in some areas to place a nickel cadmium battery into the trash or solid waste stream You may contact your local recycling center for information on where to return the spent battery or call 1 800 822 8837 for information on Ni Cd battery recycling in your area a N REAR VIEW OF CHARGER BASE um NN Plug Receptacle Wall Mount Unit Charger Base Y THE PASLODE BATTERY CHARGING SYSTEM Charging Instructions 1 Remove wall mount unit with the orange label from the tool case and plug into a 120V AC outlet Set orange charger on a stable surface and insert wall mount unit s plug into plug receptacle on the back of the charger see picture A green light indicates power is on and charger circuit is ready 2 Remove the battery from tool or case and insert terminals down into charger The red light will come on indicating that the battery is charging and the green light will go out If battery is completely discharged the red light and the green light may flash back and forth for up to 20 minutes This safety feature slowly recharges the battery until it is ready to accept the full charging current If the red and green lights continue to flash after 20 minutes replace the battery 3 After charging is complete the red light will go out and the green light will come on indicating that the battery is fully charged The charger will keep the batter
13. e linear drive internal combustion motor In order for you to fully understand the information contained in this manual you need a basic understanding of the Cordless Finish Nailer As you can see in the illustration below the Cordless Finish Nailer is made up of three major areas handle motor and magazine As you examine the Cordless 16 ga Straight Finish Nailer become familiar with the three major assemblies and the various components located in each of them The Handle Assembly contains the fuel cell indicator light and the trigger The Motor Assembly contains the cover and filter the motor housing the nose and the work contacting element The Magazine Assembly contains the components to load and control the fastener and the battery for the Cordless Finish Nailer removable cover amp filter cap motor housing soft Motor Assembly ae touch quick clear cover trigger Overview of the Paslode Cordless 16 ga Straight Finish Nailer Specifications Dimensions Weight with battery 4 Ibs 120z Height 11 3 4 inches Length 10 1 2 inches Magazine 16 ga Straight Cycle Rate Intermittent Operation 2 to 3 nails per second NOTE Exceeding these cycle rates could cause the tool to overheat resulting in loss of performance or damage to tool components By using the Paslode Cordless 16 ga Straight Finish Nailer at its recommended
14. e out of spark plug Remove cap and check spark lead insert in spark plug and replace cover Spark plug is dirty Clean tool cylinder head No spark is generated Return tool to authorized Paslode dealer for service 18 Normal Stage of Operation Troubleshooting SYMPTOM POSSIBLE PROBLEMS SERVICE Tool operates properly but fasteners do not drive fully Work contacting element requires adjustment Adjust work contacting element Fuel cell is low Check fuel cell and replace as required There may be loss of seal in combustion chamber Press work contacting element against workpiece for one minute Pull trigger If fastener does not drive there is a leak that requires service Tool operates properly but fasteners are sometimes over driven and sometimes under driven Work contacting element is not adjusted properly for the type of material being fastened Adjust work contacting element Readjust as required when material density or thickness of material being fastened changes Tool operates but no fastener is driven Wrong fasteners being used Use only fasteners meeting Paslode specifications Check Fasteners and Applications section for fastener types and sizes recommended for use in Impulse tool Follower not properly engaged behind fastener strip Position follower behind fastener strip and engage strip Jammed fastener
15. eners are collated into strips of 50 for easy loading Paslode fasteners are designed to be used in Paslode tools use of other fasteners may cause damage to the tool or injury to the tool operator THE PASLODE CORDLESS 16 ga STRAIGHT PART FINISH NAILER DRIVES THESE NAILS NO LENGTH TYPE 650281 Panel Cap Shoe Molding ee BR SST e esossi 1 3 4 Baseboard Baseboard Crown Chair Chair Servicing Restrict Field Service to the Following CHECKING THE ENERGY LEVEL OF THE BATTERY RECHARGING THE BATTERY CHECKING THE FUEL CELL AND METERING VALVE REPLACING THE FUEL CELL CLEANING REPLACING THE AIR FILTER CLEARING A JAM CLEANING THE TOOL See cleaning manual Attempts to go beyond these procedures could result in serious personal injury or damage to the Cordless Finish Nailer and voiding the warranty There are certain problems you may encounter when you are using the Cordless Finish Nailer that you will be able to correct onthe worksite The following field service procedures are the only service procedures you should attempt Anything else that may appear wrong with the Cordless Finish Nailer should only be diagnosed and repaired by a fully trained service technician If you have any reason to believe that your problem is beyond the service procedures in this manual contact your Paslode representative immediately Fuel Cell Check Ifthe Cordless Finish Nailer s f
16. is powered by an internal combustion engine and is effected by altitude The tool may lose power or not cycle consistently at elevations of 4000 feet or greater When using the tool at elevations of 4000 feet it is recommended to use the blue high altitude fuel metering valve part 219247 Fuel Cell and Metering Valve Installing Metering Valve to Fuel Cell Prior to Use To install the metering valve to a fuel cell 1 Press downward on the front side of the valve stem side until it seats 2 Press downward on the rear side of the valve until it seats 3 The valve is now completely seated onto the fuel cell and can be inserted into the tool NOTE Paslode Cordless Fuel Cells are marked with an expiration date on the bottom of the cell For maximum performance use fuel before expiration date A DANGER Paslode Cordless Fuel Cells are flammable Do not smoke when installing the metering valve Fuel Cell and Metering Valve Inserting Fuel Cell Inserting the metering valve fuel cell assembly into the Cordless Finish Nailer is very simple To begin press up at the bottom of the actuator cover and pivot outward to open The cover will swing out of the way gt 2 PULL OUT 7 Streagine d I Next with the metering valve stem pointed toward the front of the tool insert the metering valve fuel cell assembly
17. mmable chemicals adhesives gasoline or solvents warnine Do not expose the tool to temperatures in excess of 120 F 49 C Fuel and or the battery may burst releasing flammable gas Ay warnine Do not attempt to operate this tool until you have read and understood all safety precautions and manual instructions Failure to follow all safety precautions and instructions may result in a permanent loss of vision serious personal or even fatal injury property damage and or tool damage A WARNING This tool must be operated only in a well ventilated environment because the tool exhausts carbon monoxide similar to a gas chainsaw or lawnmower Exposure to carbon monoxide may cause dizziness nausea or unconsciousness vy Aawarnine ALWAYS keep the Cordless Straight Finish Nailer fuel cell battery and battery charger out of the reach of children Safety Instructions A WARNING Always wear EYE and EAR safety gear when working with or in the vicinity of the Paslode Cordless 16 ga Straight Finish Nailer CY Eye protection must meet the requirements of ANSI Standard Z87 1 and should have side shields for increased protection NEVER ASSUME THE TOOL IS EMPTY Never point the tool at yourself or anyone else NEVER ENGAGE IN HORSEPLAY WITH THE TOOL The Cordless Finish Nailer is not a toy i
18. ombustion chamber opens Fan exhausts hot gases and cools internal components A DANGER The work contacting element and nose will become hot after prolonged or rapid use If it becomes necessary to adjust the work contacting element avoid touching with bare hands Ax caution This tool must be operated in a well ventilated environment because the tool exhausts carbon monoxide similar to a chainsaw or lawn mower Exposure to carbon monoxide may cause dizziness nausea or unconsciousness 14 Turn adjustment wheel in either direction Depth of Drive Adjustment Remove the battery before adjusting the depth of drive The depth of drive adjustment is done by turning the adjustment wheel as shown by the arrows on the side of the tool Fasteners and Applications Applications The Paslode Cordless 16 ga Straight Finish Nailer is suited for a variety of applications These include securing door and window casings attaching baseboards where walls meet floors attaching moldings where walls meet ceilings securing paneling securing chair rails picture molding and other decorative trim Crown Molding Casings Hand Rail m Door Stop A Door Jamb Fasteners Chair Rail Baseboard k Cap amp Base Shoe The Paslode Cordless 16 ga Straight Finish Nailer drives Paslode 16 ga Straight Finish Nails Fast
19. re is a second container inside the fuel cell The inner container holds the fuel The space between the inner container and the outer cylinder is filled with a gas called the propellant which is under pressure To eject the fuel propellant pressure squeezes the inner fuel container much as you squeeze a tube of toothpaste This squeezing action ensures that all the fuel is used and that the Cordless Finish Nailer can operate in any position Because of this container within a container design you might hear the sound of fluid when shaking the fuel cell after all the fuel has been used This is the propellant which remains between the containers even after all the fuel has been expelled If you expose the empty fuel cell to extreme temperatures the propellant gas will expand andcould cause the container to burst releasing flammable gases Metering Valve The metering valve contains a fuel metering system to inject the correct amount of fuel into the combustion chamber The metering valve with the yellow face is the only valve that will operate properly with the Cordless 16 ga Straight Finish Nailer YELLOW FACE NOTE 1 Do not attempt to reuse the metering valve Replace with fresh fuel cell valve and dispose of spent cell valve properly 2 When replacing fuel cell also clean the air filter for optimum tool operation NOTE Altitude Restriction 10 Paslode Cordless technology
20. rks Inc Paslode Cordless 16 Gauge Straight Finish Nailer Operating Manual This manual is intended to acquaint you with the Paslode Cordless 16 ga Straight Finish Nailer Unlike other power fastening tools the Cordless Finish Nailer is powered by an Introduction and Warranty The Cordless Finish Nailer should be handled like other power fastening tools that you use Like most tools when used improperly injury could result If you are going to allow others to use the Cordless Finish Nailer it is your responsibility to make sure that they also read and comply with the instructions in this manual before attempting to internal combustion linear motor In simpler terms your operate the tool Cordless Finish Nailer is powered by a motor similar to the one that powers an automobile The Cordless Finish Nailer ignites a fuel and air mixture to produce the energy to drive the motor which in turn drives the fastener The Cordless Finish Nailer is totally self contained It carries its own fuel supply and battery along with a supply of fasteners Should you have questions about the Cordless Finish Nailer or wish to obtain additional copies of this manual please contact your Paslode representative The space below is provided so that you may record your representative s name address and telephone number For ease of use this manual is divided into sections see For the nearest Paslode representative call 1 800 Con
21. sory provided in accordance with this warranty will carry a warranty for the balance of the period of warranty applicable to the part it replaces This warranty does not apply to part replacement required due to normal wear This warranty is void on any tool which has been subjected to misuse abuse accidental or intentional damage use with fasteners fuel batteries or battery chargers not meeting Paslode specification size or quantity improperly maintained repaired with other than genuine Paslode replacement parts damaged in transit or handling or which in Paslode s opinion has been altered or repaired in a way that affects or detracts from the performance of the tool PASLODE MAKES NO WARRANTY EXPRESSED OR IMPLIED RELATING TO MERCHANTABILITY FITNESS OR OTHERWISE EXCEPT AS STATED ABOVE and Paslode s liability AS STATED ABOVE AND AS ASSUMED ABOVE is in lieu of all other warranties arising out of or in connection with the use and performance of the tool except to the extent other wise provided by applicable law PASLODE SHALL IN NO EVENT BELIABLE FORANY DIRECT INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO DAMAGES WHICH MAY ARISE FROM LOSS OF ANTICIPATED PROFITS OR PRODUCTION SPOILAGE OF MATERIALS INCREASED COST OF OPERATION OR OTHERWISE Description The Paslode Cordless 16 ga Straight Finish Nailer is a self contained fully portable nailer that uses liquid hydrocarbon fuel to power a uniqu
22. t is a tool Careless and improper use may result in a serious accident NEVER CARRY THE TOOL WITH YOUR FINGER ON OR SQUEEZING THE TRIGGER This practice may result in the accidental discharge of a fastener NEVER OPERATE A MALFUNCTIONING TOOL Refer to the servicing or troubleshooting section of this manual to correct the problem If the problem cannot be corrected stop using the tool and report it to your supervisor or Paslode representative DO NOT LOAD FASTENERS WITH THE TRIGGER AND OR WORK CONTACTING ELEMENT PRESSED IN A fastener may be accidentally discharged NEVER OPERATE THE TOOL WITH THE WORK CONTACTING ELEMENT REMOVED OR DISABLED This device helps reduce the possibility of accidental fastener discharge by preventing the tool from operating until it is completely against the work surface NEVER operate the tool if the work contacting element is not working properly ALWAYS POINT THE TOOL AWAY FROM YOURSELF AND OTHERS WHEN CLEARING JAMS OR REMOVING FASTENERS Pull the follower slightly back and push the release lever Tip the tool nose up slightly and fasteners should slide out of the rear of the magazine If fasteners are jammed refer to the appropriate servicing section of this manual NEVER OPERATE THE CORDLESS FINISH NAILER IF PARTS ARE LOOSE DAMAGED OR MISSING DO NOT DRIVE FASTENERS INTO KNOTS OR ON TOP OF OTHER FASTENERS A fastener may ricochet and cause serious injury 11 OPER
23. tents Each section of the manual is written with you 682 3428 the tool operator in mind We have left out many of the technical terms so that you can easily understand howto get Name the maximum performance from your Cordless Finish Nailer and how to avoid damaging the tool or injuring yourself But to accomplish this we need you to do two things Address 1 READ THE MANUAL FROM COVER TO COVER BEFORE USING THE TOOL City State Zip 2 FOLLOW ALL INSTRUCTIONS IN THE MANUAL Telephone Numbe Paslode Cordless Warranty and Limitations Paslode warranties that new Cordless power fastening tools WARRANTY STATEMENT parts and accessories will be free from defects in material and workmanship for the period shown below after the date of delivery to the original user ONE YEAR LIMITED WARRANTY A one year warranty will apply to all parts except those listed below as normal wearing parts or parts which are specifically covered by an extended warranty FIVE YEAR EXTENDED LIMITED WARRANTY A five year warranty will apply to all molded nylon parts e Cap and Grille Handle Halves and Actuator Trigger 90 DAY LIMITED WARRANTY A 90 day warranty applies to the following parts which are considered normal wear parts Bumper Driver Blades O Rings Paslode s sole liability hereunder will be to replace any part or accessory which proves to be defective within the specific time period Any replacement part or acces
24. tools indicator light is red charger not working properly Replace charger or monitor charging time to ensure battery has adequate time for recharging It is normal for battery to feel warm after properly charging Battery damaged or cycle life exhausted Replace battery Charger gets hot makes excessively loud noise or smokes during charging cycle Charger cord or wall plug gets hot Damaged charger Discontinue use immediately and unplug from power source Replace charger and tag or dispose of charger to prevent accidental re use or connection to power source Normal Stage of Operation SYMPTOM POSSIBLE PROBLEMS SERVICE Fan does not run tool indicator light is blinking red or solid red Battery is not charged Charge battery Battery terminals are oily dirty or corroded Clean battery terminals with soft cloth Fan does not run or runs slower than normal tool indicator light is solid red Battery is discharged Charge battery Work contacting element does not depress fully tool does not operate Work contacting element is bent or build up of debris in track restricts operation Remove and inspect lower probe Clean the track Repair or replace lower probe as required Lockout feature is engaged Add strip of nails Tool will not cycle fan runs indicator light is solid green Fuel Cell empty Replace fuel cell Spark wir
25. y at full charge until it is removed 4 Unplug the wall mount unit from the charger and remove the wall mount unit from the 120V AC outlet CHARGING TIMES First charge new battery Discharged Battery 2 hours 5 minutes to 2 hours CHARGING DON TS 1 Do not charge battery outdoors or in temperatures below 40 F 5 C 2 Do not allow metal objects to come in contact with battery terminals 3 Do not puncture or attempt to open battery case or cells 4 Do not store battery where it will be subjected to temperatures above 120 F 49 C 5 Do not incinerate battery 6 Do not use a defective battery charger one that over heats and or smokes when plugged in 7 Do not immerse the battery in water Charging System Accessories Battery Charger Kit Part No 900200 Wall Mount Transformer Part No 900477 Battery Charger Base Part No 901230 Automotive Adapter Part No 900507 Cannot use with previous gray in color charging system components ee EN AC DED ay M Inserting Battery 1 Load the battery contacts first into the Cordless Finish Nailer 2 Push battery fully forward into its locked position 3 To remove battery push down on locking tab and slide battery out NOTE If battery is left in tool for an extended period the battery will discharge completely and will require recharging
26. zine until the follower passes the last strip of fasteners Step 3 Release the lever on the follower and let the follower push the nails forward into the nose of the tool gt Pull Follower In the illustration above you will see an indicator arrow on the side of the follower When the indicator arrow is in the reload area marked on the side of the magazine you may insert a new strip of nails When the indicator arrow reaches the lockout area the tool automatically locks preventing the tool from operating To unlock the tool simply reload another strip of nails Lockout Feature The purpose of this feature is to prevent needless blank cycling which could mar woods waste fuel and damage tool components Ten 10 nails will be left in the magazine when the follower reaches the lockout area When changing fastener length or loading at the beginning of the work day you should inspect the magazine and nose for any fasteners left in the tool These nails will not be visible unless you open the nose of the tool Paslode Cordless 16 ga Straight Finish Nailer and Outdoor Weather Use the Cordless Finish Nailer outdoors in dry weather when the nailer fuel cell and battery are between 20 F 7 C and 120 F 49 C HOT WEATHER OPERATION The Cordless Finish Nailer requires cooling of the motor assembly to operate properly The fan normally provides the necessary air flow to permit
Download Pdf Manuals
Related Search