Hampton Bay TY-50-A(HD) Use and Care Manual
Contents
1. Connect duct Install a circular duct to outlet and secure it with duct tape or clamps Install the duct G to the outlet with a gradient 1 2 to the outside as shown 11111111111111 111 LL L1 ALL LL AL LLL Installation continued Connect wiring from house to Using quick connect box WARNING Wiring must comply with all applicable electrical codes Turn OFF power before removing or installing connectors WARNING Follow all local electrical and safety codes WARNING COPPER TO COPPER ONLY Do not use on x Aluminum wire CAUTION Never place a switch where it can be reached from a tub or shower A CAUTION Accessory part DD quick connect should meet Connect house wires to ventilation fan wires installation instructions below Match colors as shown NOTE Connector is reusable on solid wires of the same wire gage or smaller Do not reuse connector on stranded wires HOUSE ELECTRICAL BOX Strip the wires so half of the bare wire is showing Grip the wire firmly and push the stripped end of the wire into the open port of connector DD Use only one stripped end of the wire per port Verify the stripped end of the wire is fully inserted to the back of the connector DD FAN SWITCH DD L BLK 120 VAC RG N WHY GRD GREEN amp YELLOW FAN ELECTRICAL BOX CAUTION If your house wires do not2. 10 Troubleshooting CAUTION Do not install in locations where the air temperature will exceed 104 F 40 C Problem Possible Cause Corrective Action Fan will not turn on Power off Make sure the power supply is on Faulty switch Test or replace the switch Faulty wire connection Check wire in the switch box Care and Cleaning Before servicing or cleaning the unit disconnect and lock the power supply at the panel to prevent the power from being turned on Remove the grill by squeezing the springs and pulling down Wash and clean the grill in a sink and dry with a cloth Remove dust and dirt from the fan housing with a vacuum cleaner Dampen cloth with dish detergent wipe the fan housing and dry with a cloth Replace the grill www hamptonbay com 11 Please contact 1 877 527 0313 for further assistance Specifications TY 50 A HD ULTRA SILENT VENTILATION FAN Model No TY 50 A HD Air direction 50 cfm Voltage 120 V Hertz 60 HZ Duct diameter 4 in 10 16 cm Noise 0 5 Sone Power consumption Watts 20 W Speed 900 rpm Air deliver at 0 1 WG 50 cfm Weight 10 5 Ibs 4 8 kg DIMENSIONS Ceiling opening length 9 5 in 24 13 cm Ceiling opening width 9 5 in 24 13 cm Ceiling opening depth 8 26 in 21cm
3. Housing dimension length 9 13 in 23 cm Housing dimension width 9 13 in 23 cm Housing dimension depth 7 75 in 19 6 cm TY 80 A HD SILENT VENTILATION FAN Model No TY 80 A HD Air direction 90 cfm Voltage 120 V Hertz 60 HZ Duct diameter 4 in 10 16 cm Noise 1 0 Sone Power consumption Watts 30 W Speed 1000 rpm Air deliver at 0 1 WG 90 cfm Weight 10 5 Ibs 4 8 kg DIMENSIONS Ceiling opening length 9 5 in 24 13 cm Ceiling opening width 9 5 in 24 13 cm Ceiling opening depth 8 26 in 21 cm Housing dimension length 9 13 in 23 cm Housing dimension width 9 13 in 23 cm Housing dimension depth 7 75 in 19 6 cm 12 Service Parts TY 50 A HD SERVICEABLE PARTS 50 006 50 007 50 008 50 001 0 002 gu 50 003 QY 50 004 Part number Description Quantity 50 001 Quick connectors 3 50 002 Long wood screws 8 50 003 Short screw M4x12 2 50 004 Short screw M4x6 2 50 005 Grill 1 50 006 Complete assembled fan and housing 1 50 007 Complete suspension brackets 1 www hamptonbay com 13 Please contact 1 877 527 0313 for further assistance Service Parts continued TY 80 A HD SERVICEABLE PARTS 80 006 50 00
4. 2 initial install Use long wood screws BB to loosely attach the main body of fan A to the ceiling joist in the four locations shown Fit bracket IV B against the main body of fan ensuring bracket is snug against the opposite ceiling joist Fit bracket D against main the body of fan ensuring bracket IV is snug against the opposite ceiling joist Use long wood screws to loosely attach bracket to opposite ceiling joist as shown Proceed to step 6 www hamptonbay com Please contact 1 877 527 0313 for further assistance Installation continued 4 Configuration 3 preparation Connect bracket D to bracket Il C using two M4x6 screws CC 6 Final installation Ensure the main body A is level Ensure the flange on the main body is flush with the ceiling joist Firmly secure all screws on the main body and any installed brackets Use long wood screws BB to secure the main body flange to bottom of ceiling joist as shown 9 Configuration 3 initial install Use long wood screws BB to loosely attach the main body of fan A to the ceiling joist in the four locations shown Fit connected brackets C D against the main body of fan ensuring they are snug against the opposite ceiling joist Use long wood screws to loosely attach bracket and 2 C D to the opposite ceiling joist as shown Proceed to step 6
5. authorities WARNING Not suitable for use as a range hood or in areas where hazardous or explosive vapors are present CAUTION Do not install in locations where the air temperature will exceed 104 F 40 C IMPORTANT Exercise care to not damage existing wiring when cutting or drilling into walls or ceilings NOTE Make sure duct work size is a minimum of the discharge Do not reduce Reducing the duct size can increase fan noise IMPORTANT You may want to consult with a professional electrician regarding the wiring of your ventilation fan WARNING To reduce the risk of electric shock please disconnect the electrical supply circuit to the fan before installing light kit CAUTION This product must be properly grounded gt Pee Obp Warranty The manufacturer warrants the products to be free from defects in materials and workmanship for a period of three 3 years from date of purchase This warranty applies only to the original consumer purchaser and only to products used in normal use and service If this product is found to be defective the manufacturer s only obligation and your exclusive remedy is the repair or replacement of the product at the manufacturer s discretion provided that the product has not been damaged through misuse abuse accident modifications alterations neglect or mishandling This warranty shall not apply to any product that is f
6. match these colors determine what each house wire represents before connecting You may need to consult a licensed electrician to determine this safely Product wires To switch box NOTE Important wire information Maximum temperature rating 105 C 221 F 600 volts maximum for building wire and 1000 volts maximum in signs and lighting fixtures A Flammability rating of the wires must meet UL94 V2 The acceptable wire range includes Solid 12 20 AWG Stranded 12 16 AWG lt 19 STRAND 18AWG 7 STRAND Tin bonded 14 18 AWG lt 19 STRAND www hamptonbay com 9 Please contact 1 877 527 0313 for further assistance Installation continued 1 0 Connect wiring from box to switch 1 1 Attach grill Insert the mounting springs into the slots in the A WARNING Follow all local electrical and safety codes grill F Squeeze springs together and insert into the Connect wires to switch using the quick connect main body DD or wire nuts not provided Match colors as shown 120 VAC LINE IN WHITE WIRE N BLACK WIRE L GREEN amp YELLOW GRD BLACK WIRE TO SWITCH BOX DD To switch box Sl Product wires WARNING Failure to wire product correctly could result in electrical shock fire hazards or damage to the product Consult a licensed electrician if you are unsure of your ability to correctly install wiring
7. 7 50 005 TAL SS EP gt 5000 gt 80 001 Qe 002 Qa 50 003 QP 50 004 Part number Description Quantity 50 001 Quick connectors 2 80 001 Quick connectors 1 50 002 Long wood screws 8 50 003 Short screw M4x12 2 50 004 Short screw M4x6 2 50 005 Grill 1 80 006 Complete assembled fan and housing 1 50 007 Complete suspension brackets 1 14 This page intentionally left blank www hamptonbay com 15 Please contact 1 877 527 0313 for further assistance Questions problems missing parts Before returning to the store call Hampton Bay Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HAMPTONBAY COM Retain this manual for future use 20111010 M
8. Item 986 755 Model TY 50 A HD Item 986 793 Model TY 80 A HD USE AND CARE GUIDE VENTILATION FAN Questions problems missing parts Before returning to the store call Hampton Bay Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HAMPTONBAY COM THANK YOU We appreciate your trust and confidence in Hampton Bay with your purchase of this ventilation fan At Hampton Bay we make quality products to help you improve your home and give you peace of mind about your choice Don t forget to visit our website for other Hampton Bay products We hope you enjoy this new addition to your home and thanks again for choosing Hampton Bay Table of Contents Table of ContentsS emmm nennen enam naaa naaa 2 Safety Information rien 2 Warranty anca nici 3 Pre INstallation nn na a 4 Planning For Successful Installation 4 Installation Options 4 Tools Required A aaa 5 Materials Required esen 5 Hardware Included cccecceeeeeeeeeeeecaeeeeeeeeeteees 5 Package Contents 6 Safety Information 1 This ventilation fan is approved for use over a bathtub or shower when installed in a GFCI protected circuit Do not use unapproved fans over a bathtub or shower that is not approved for that application 2 Installation work must be carried out by a qualified person s in accordance with a
9. iling is in place 9 When installing in existing construction use the dimensions on page 12 to determine the required hole size for the ceiling Grill edges should overlap finished ceiling Elbow near the body j NOTE If installing in existing construction you must Too many elbows Fan have access to space above and below the installation Body location Minimum 18 INSTALLATION OPTIONS We recommend installing the ventilation fan by securing the main body of the fan against one ceiling joist and using the header bars as necessary for support of the adjoining joist There are multiple installation configurations possible for this ventilation fan Not all configurations are shown If your installation requires a variation other than those shown consult with a licensed contractor to determine the best installation for your project If you are replacing an existing fan ensure that the new grill will adequately cover the existing opening Pre Installation continued TOOLS REQUIRED Safety Hammer TA goggles D IT Drill MATERIALS REQUIRED Dut Duct Duct Duct JE vent clamp tape CCH piping HARDWARE INCLUDED Phillips a Electrical i screwdriver SEENE Level tape A NOTE Hardware shown to actual size awy Qu AA ie DU CC i o Part Description Quantity AA Short screw M4x12 2 BB Long wood screw ST4x30 8 CC Screw M4x6 2 DD Q
10. ll local and safety codes including the rules for fire rated construction 3 Always vent fans to the exterior and in compliance with local codes 4 Install ductwork in a straight line with minimal bends 5 Use 120 V 60 Hz for the electrical supply and properly ground the unit Follow all local safety and electrical codes 6 Do notuse this fan with any solid state control device such as a dimmer switch Solid state controls may cause harmonic distortion which can cause a motor humming noise 7 Toreduce the risk of fire or electric shock do not block air entry grill 8 Sufficient air is needed for proper combustion and exhausting of gases through the flute chimney of fuel burning equipment to prevent back drafting Installation ss es 7 Troubleshooting a 11 Care and Cleaning iii 11 Specifications 12 Ty 50 A HD Ultra Silent Ventilation Fan 12 Ty 80 A HD Silent Ventilation Fan 12 Service Parts apauianiieaaini 13 TY 50 A HD Serviceable Paris 13 TY 80 A HD Serviceable Paris 14 Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air conditioning Engineers ASHRAE and the local code
11. ound to have been improperly installed set up or used in any way not in accordance with the instructions supplied with the product This warranty shall not apply to a failure of the product as a result of an accident misuse abuse negligence alteration faulty installation or any other failure not relating to faulty material or workmanship This warranty shall not apply to the finish on any portion of the product such as surface and or weathering as this is considered normal wear and tear The manufacturer does not warrant and specially disclaims any warranty whether express or implied of fitness for a particular purpose other than the warranty contained herein The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage including but not limited to any labor expense costs involved in the replacement or repair of said product Contact Customer Service Team at 1 877 527 0313 or visit www hamptonbay com www hamptonbay com 3 Please contact 1 877 527 0313 for further assistance Pre Installation PLANNING FOR SUCCESSFUL INSTALLATION Do not install ventilation fan in areas where the duct When installing the ventilation fan in a new work will require configuration as shown construction site install the main body of the fan and duct work during the rough in construction of the building The grill should be installed after the finished Tuming angle too sharp ida ce
12. uick connect 3 www hamptonbay com 5 Please contact 1 877 527 0313 for further assistance Pre Installation continued PACKAGE CONTENTS N N A Part Description Fan body Installation bracket IV Installation bracket Il Installation bracket Installation bracket III nim oloo S gt Grill Installation 1 Determine joist width Measure the distance from the center of the two ceiling joists where you will be installing the ventilation fan Use the table to determine the header bar installation For configuration 1 proceed to step 2 For configuration 2 proceed to step 3 For configuration 3 proceed to step 4 Use the following to determine the proper installation configuration Width between the Joists Brackets Used Configuration 12 in I 1 16 in I IV 2 19 2 in I Il 3 Configuration 1 initial install Use long wood screws BB to loosely attach the main body of fan A to ceiling joist in the four locations shown Fit bracket D against the main body of fan ensuring the bracket is snug against the opposite ceiling joist Use long wood screws to loosely attach bracket to the opposite ceiling joist as shown Proceed to step 6 Configuration
Download Pdf Manuals
Related Search