American Standard 9075.120 Installation Guide
Contents
1. are definitely recommended for younger children b Pregnant or possibly pregnant women should consult a physician before using the whirlpool Water temperatures in excess of 100 Fahrenheit are not recommended b The use of alcohol drugs or medication before or during the use of the whirlpool may lead to unconsciousness with the possibility of drowning Consult your physician before using the whirlpool if you are using any medication d Persons suffering from obesity or with a medical history of heart disease low or high blood pressure circulatory system problems or diabetes should consult a physician before using the whirlpool 4 WARNING Risk of Child Drowning To reduce the risk of accidental drowning do not permit children to use the whirlpool unless they are closely supervised 5 WARNING RISK OF ELECTRICAL SHOCK All electrical connections must be accomplished by a qualified electrician in accordance with Article 680 of the National Electric Code and any local codes In addition a GFCI MUST protect all branch circuits to the whirlpool and every electrical component MUST be grounded 6 The unit must be connected only to a supply circuit that is protected by a ground fault circuit interrupter GFCI Such as GFCI should be provided by the installer and should be tested on a routine basis To test the GFCI push the test button The GFCI should interrupt power Push the reset button Power should be restored If the GFCI2. American Standard will repair or at its option exchange the product for a similar model This warranty applies only to the original purchaser and installation of these products This limited warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damages if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which ca
3. E Z Install Heater Americam Standard Whirlpool Heater EZHEAT 100 INSTALLATION INSTRUCTIONS Your E Z Install whirlpool bathtub heater has been specifically designed to enhance the enjoyment of your whirlpool bath Once filled the temperature of the whirlpool bath is constantly maintained by a built in thermostat for as lon p y y g PE e E Z INSTALL HEATER as you desire Your E Z Install whirlpool bathtub heater is totally self contained to insure trouble free installation and operation As with all electrical devices certain safety precautions should be taken during installation and operation Please read and follow all instructions carefully IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS You should have received safety instructions with your whirlpool bathtub system Please read and follow them carefully Those instructions will include the following warnings 1 WARNING Risk of Electrical Shock Do not permit any electrical appliances such as a light telephone radio or television within five feet of the whirlpool bathtub 2 DANGER To reduce the risk of injury do not remove the suction cover from the whirlpool bathtub 3 To Reduce the Risk of Injury a The water in your whirlpool should not exceed 104 Fahrenheit Lower water temperatures are recommended for extended use exceeding 10 15 minutes and
4. a preset pressure switch The pump must be running with water flowing in the whirlpool to allow the heater to turn on a SEs E Z INSTALL jiexitn Indicator Light This light turns on whenever the heater is operating Fig 1 High Limit Switch The heater includes an exclusive Intelligent High Limit This safety circuit will not false trip from hot tap water It will only turn the heater off if the thermostat fails If the high limit trips frequently call a service technician To manually reset the circuit in the event that the High Limit switch has been activated simply 1 Turn off the whirlpool pump 2 Drain water from the tub 3 Remove power from heater by unplugging at receptacle or turning off circuit breaker 4 The heater circuit will automatically reset in less than 15 minutes 5 Restore power to the heater 6 Whirlpool bath is now ready to use ELECTRICAL CONNECTIONS Install a separate 120VAC 15AMP dedicated circuit with GFCI Ground Fault Circuit Interrupter protection At initial start up with power ON push the GFCI test button The reset button should pop out Push this button in to reset If the GFCI fails to operate in this manner there is a ground fault or malfunction indicating the possibility of electrical shock Turn off the power and do not use the bath until the source of the problem has been identified and corrected 1 Route two separate circuits to the junction box near the whirlpool
5. as shown in Figure 2 Each circuit MUST BE GFCI PROTECTED and must use copper conductors only 2 Ensure the heater and pump are properly GROUNDED and BONDED as required Attach the 8 AWG solid copper conductor supplied with the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3 The conductor is secured to the lugs using set screws The motor frame shall have a second 8 AWG solid copper conductor connected from the frame bonding lug to the homes electrical panel or approved local bonding point as shown in Figure 3 2 SEPARATE Fig 2 TAME GFE OUTLET ELECTRICAL INSTALLATION 120 VAC HEATER American Standard E Z INSTALL HEATER PUMP MOTOR HEATER RUN 6 AWG SOLID COPPER CONDUCTORS FROM HEATER BONDING LUG TO PUMP MOTOR FRAME LUG AND FROM PUMP MOTOR SEPARATE 15 AMP GFCI OUTLET LUG TO APPROVED for 1 6 H P PUMP __ GROUND AS SHOWN SEPARATE 20 AMP GFCI OUTLET for2 1 H P PUMP 120 VAC FIRST COPPER CONDUCTOR SECOND COPPER CONDUCTOR PUMP MOTOR FRAME WITH P BONDING LUGS TO GROUND ELECTRICAL DIAGRAM READ AND FOLLOW ALL INSTRUCTIONS 753555 100 Rev E 2 INSTALLATION INSTRUCTIONS To ensure that you have received the proper heater designed to operate specifically with your bathtub locate the bathtub part number within the approved list located on the heater assembly If you cannot locate the specific bathtub part number do not install the heater assembly until the pr
6. fails to operate in this manner the GFCI is defective If the GFCI interrupts power to the bathtub without the test button being pushed a ground current is flowing indicating the possibility of an electric shock Do not use this bathtub Disconnect the hydromassge bathtub and have the problem corrected by a qualified service representative before using 7 WARNING Prolonged immersion in hotter water may induce hyperthermia Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98 6 F The symptoms of hyperthermia include an increase in the internal temperature of the body dizziness lethargy drowsiness and fainting The effect of hyperthermia include a Failure to perceive heat b Failure to recognize the need to exit the bathtub c Unawareness of impending hazard d Fetal damage in pregnant women e Physical inability to exit the bathtub SAVE THESE INSTRUCTIONS American Standard Inc 2007 753555 100 Rev E All product names listed herein are trademarks of American Standard Inc unless otherwise noted OPERATION WARNING Prior to operation review the Important Safety Instructions listed at the beginning of this instruction manual Once the heater is installed and the whirlpool pump is operating the heater is totally automatic The heater will help maintain the temperature of the water in the bath Pressure Switch The heater is equipped with
7. oper heater is received 1 The E Z Install heater can be installed either before or after bathtub installation 2 Identify the location of the inline heater blank It should be near the pump as shown in photo 1 3 Using channel locks loosen the couplings from the whirlpool piping photo 2 Photo 2 4 Remove the spacer pipe leaving the gaskets on the whirlpool pipe connections photo 3 NOTE Gaskets must be in place to ensure a watertight seal Photo 3 753555 100 Rev E 5 Insert the E Z Install heater in the open space on the piping and connect the couplings on the heater to the whirlpool piping photo 4 Be sure that the re set button faces toward the access panel opening Photo 4 6 Tighten the couplings with the channel locks photo 5 Photo 5 7 Fill the tub with water and check for leaks 8 Install heater ground per Figure 3 and plug the E Z Install heater s power cord into the dedicated 15 amp GFCI outlet 9 Start the pump and confirm that there are no leaks 10 Turn the pump on and look to see if the light on the E Z Install heater is lit This indicates that the heater is operating If not check the electrical connections at the outlet AMERICAN STANDARD ONE YEAR LIMITED WARRANTY If inspection of this American Standard plumbing product within one year after its initial purchase confirms that it is defective in materials or workmanship
8. se this warranty does not affect such statutory rights For service under these warranties it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States In Canada InMexico American Standard Inc American Standard CustomerServiceManager P O Box 6820 2480 Stanfield Road IdealStandard S A deC V Piscataway NewJersey 08855 Mississauga Ontario ViaMorelos 330 Attention Director of Consumer Affairs Canada L4Y1S2 Col SantaClara Ecatepec55540Edo Mexico For residents of the United States Toll free 800 387 0369 www americanstand warranty information may also be www americanstandard ca obtained by calling the following toll free number 800 442 1902 www americanstandard us com SERVICE For service or repair contact the number below The model number and serial number for your whirlpool are located on a label near the motor HOTLINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 weekdays 8 00a m to 6 00p m Eastern Time Product names listed herein are trademarks of American Standard Inc American Standard Inc 2007 753555 100 Rev E 4 85 0049AEZ Rev 6
Download Pdf Manuals
Related Search