AireRyder LK51218WP Instructions / Assembly
Contents
1. 5 Thread the fixture wires through the coupling hex nut long nipple big tube cap canopy metal pad washer grounding pad and another hex nut 6 Secure the coupling onto the stem on the top of the light kit Then screw the long nipple into the coupling then secure it with a hex nut 7 Slip the big tube cap with the open side facing downward and the canopy down through the long nipple secure them together with a metal pad washer grounding pad and hex nut 8 Cut the redundant wires if necessary Pull out the outlet wires and the house grounding wire from the outlet box Make wire connections using the wire nuts Connect the black wire from fixture to the black wire from power source Connect the white wire from fixture to the white wire from power source Attach the fixture grounding wire to the mounting strap with the green grounding screw Then connect it to the house grounding wire with the wire nut Carefully put wires back into the outlet box 9 Attach the canopy to the mounting strap and secure it with the bolt nuts 10 Follow steps 10 13 as For Light Kit LK51278 Page 2 Light hes Outlet Box Wire Grounding Wire Wire Nut A __7 Mounting Strap Bh SS S ye TE Lock Nut ee Mounting Screw Green Grounding Screw Hex Nut E ndg Pad Washer Metal Pad Sane py Bolt Nut Big Tube Long Nipple Hex Nut fp Coupling set Scre2. ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE NOTE 1 Before installing consult local electrical codes for wiring and grounding requirements 2 The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless additional support is provided for the fan Motor For Light Kit i Coupling Switch Box 1 Remove the switch box cover from the switch ee ee wre Wate Wie box of the fan by loosing the three switch box ee Wie K 2B White Wire Screws E Hex Nut amp Washer 2 Unscrew the center plug from the switch box Center Plug Qu a0 Switch Box Screw cover and discard it et I Switch Box Cover 3 Thread the fixture wire through the switch box Stem Set Screw rei AYN Metal Bar 4 Attach the switch box cover to the light kit then Light Kit f H ENN secure it with a washer and hex nut re 5 Thread the pull chain through a hex nut and the ee E26 medium base spiral short nipple Screw the short nipple into the Sana Mee on ches T coupling and secure it with a hex nut Short Nipple Glass Shade i 6 Install bulbs included See relamping label at socket area or packaging for maximum allowed wattage 7 Gently place the glass shade into the decorative ring With the pull chain and short nipple passing U through the hole
3. of glass shade attach the glass Decorative Ring gt shade assembly up to the metal bars and fasten it by securing the set screws into the nuts of decorative ring 8 Cut the redundant wires if necessary Pull out the wires from the switch box Make wire connections using the wire nuts Rubber Pad The black wire from the light kit to the black mex nus or blue wire from the switch box The white wire from the light kit to the white wire from the switch box Carefully put the wires back into the switch box 9 Attach the switch box cover back to the switch box using the three switch box screws 10 Thread the pull chain through a rubber pad metal pad and hex nut then secure them onto the short nipple Do not over tighten 11 Thread the pull chain through the cover and finial then slide the cover up to the glass shade secure it with finial 12 Secure the pine needles and pine cones onto the studs of the decorative ring 13 Turn on the power at the main fuse or circuit breaker box You can control the light with the pull chain aireRyde F A N Cc _ O LK51218 Page 1 090406 For Semi Flush 1 Take out the parts from the hardware package For Semi Flush 2 Attach two screws to the mounting strap and secure it with two lock nuts Adjust the length of the screws if necessary 3 Attach the mounting strap to the outlet box by using two mounting screws 4 Follow steps 5 7 as For Light Kit
4. w Mei Bar Coupling Pull Chain fluorescent Bulb Hex Nut Max 13W incluced Short Nipple a Glass Shade Pine Needle Hex Nut Metal Pad Cover Finial aireRyde F A N Cc O 090406
Download Pdf Manuals
Related Search